|
| 1 | M&L for brick work with sub class B, burnt clay bricks of old size, designation 75 (minimum average compressive strength 75 Kgf per sqcm), straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:4, below/above GL as per requirement complete all as specified & directed. |
| 2 | M&L for rendering 15mm thick on fair face of brick walls or concrete surfaces in CM 1:6 on brick surfaces, finished with Neeru finish on walls without using extra cement complete all as specified and as directed. |
| 3 | M&L for rendering 15mm thick on fair face of brick walls or concrete surfaces in CM 1:4 with WPC @ of 3% by wt of cement surfaces finished even and smooth without using extra cement complete all as specified and directed.Note: WPC will be measured and paid separately |
| 4 | M&L for mild steel TMT bars 10mm dia and over, Fe500/Fe500D grade confirming to IS-1786, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed. |
| 5 | M&L for mild steel TMT bars 8mm dia and over upto & inculding 10mm dia, Fe500/Fe500D grade confirming to IS-1786, cut to length cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacer & binders complete all as specified & directed. |
| 6 | M&L for frameless partition for window/door with acoustic insulated glass(saint gobain/modi make) of 12mm thick air gap+12 mm on two/three side filled with silicon cork sealants with desired frameless or aluminium framework (using ply & sun mica, if required), also and fixing with dorma/ozone make single leg spider, ceiling/bottom to glass connector, glass to glass connector, handle, door set, floor spring(as per reqmt), pivot etc. Glass will be fixed as per acoustic parameter to maximum cut low frequencies all the necessary fittings upto all height including scaffolding, complete all as per the direction of Engineer-in-charge. |
| 7 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 8 | M&L for Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat, complete all as specified and directed. |
| 9 | M&L for RCC M-25 design mix as in Beams, cantilevers,lintels, columns pillars,piers, posts, struts, chullah hoods, stair case,arches, domes, vaults,shell roofs, arch ribs, folded plates, slabs, balconies, canopies, deck slabs etc. or in similar articles upto 5th floor level complete all as specified and as directed by Engineer-in-Charge |
| 10 | S&F three track with two or more shutter with 4mm thicktinted glass, one shutter of Stainless steel wire cloth 0.36mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing , handle lock , rubber beading and glazing clips etc using following aluminium powder coated section conforming to following catalogue of \"JINDAL\" or of equivalent make as mentioned in list of makes here-in-after complete all asspecified and as directed by Engr-In-Charge(a) Bottom frame20620(b) Top frame & vertcal20621 (c) Handle (side) 20606 (d) Shutter Interlock 20724(e) Shutter Top & bottom20844 (f) Glazing clip19352 |
| 11 | S&F 12mm thick toughened glass as in doors (frameless), size 1.8 mtr x 2.4 mtr, floor mounted, stainless steel handle 300mm long-02 Nos. on each leaf, locking arrangement, including all fittings and hardwares and similar work including cutting to shape drilling holes as required complete all as specified & directed.Note: The toughened glass door shall be provided in two leafs. |
| 12 | S&F anodised powder coated aluminium partition wallor fixed type window/ventilator made out of aluminium anodised standard hollow section100 x 44 x 1.60mm thick snap fit beading standard rubber gasket 5.5mm thick glass or 12mm thick prelaminated particle board interior grade prelaminated one side with decorative choice laminates and other side balancing light grey lamination etc complete all as specified and as directed. |
| 13 | M&L for preparing newly plastered surface of walls and applying two coats of exterior acrylic paint (water based) over a coat of primer in camoflaging pattern of any shade and pattern complete all as specified and directed. |
| 14 | M&L for preparing newly plastered surface and applying two coats of distemper oil emulsion over a coat of 3mm putty complete all as specified and directed |
| 15 | Supply only Dr fixit integral WPC /liquid complete all as specified and directed. |
| 16 | M&L for concealed submain wiring with two single core 4 sqmm stranded copper conductor PVC insulated and unsheathed cable ISI marked drawn in 25mm dia, medium grade, PVC conduit concealed in wall for sub main connection including 4Sqmm PVC insulated unsheathed copper conductor ISI marked as earth wire complete all as specified and directed by Engr-In-Charge.Note: Two runs of 4sqmm cable, one run of 4sqmm earth conductor cable and one run of PVC conduits shall be measured and paid together as one unit length. |
| 17 | M&L for point wiring (concealed type) 1.5 sqmm single core PVC insulated FRLS unsheathed 1100 volts grade copper conductor multi standed cable drawn through non-metallic rigid PVC conduits and conduit accessories and provision of one run of PVC insulated FRLS unsheathed 1100 volts grade copper conductor multi-standed single core cable of size 1.5sqmm and connected to common earth dolly including provision of suitable size of modular metal box flush in wall with and including white colour cover plates for mounting modular type switches, sockets, fan regulators, bell pushes etc. for one light point, ceiling fan, Exhaust fan controlled by one switch 1 way complete all as specified and directed. |
| 18 | M&L for modular switch 1 way 6A, 230volts, 1module, complete all as specified and directed. |
| 19 | M&L for modular fan regulator electronic step type, 230volts, suitable for 1200mm sweep ceiling fan, complete all as specified and directed. |
| 20 | S&F LED luminaire 600mm x 600mm, 40watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete, 3600K, total Im not less than 3600lm complete all as specified and directed. |
| 21 | S&F ceiling fans complete with blades, down rods, without remote with electronic regulator and accessories, 230 V, 1200mm sweep Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) Complete all as specified and directed. |
| 22 | S&F in replacement plug top & socket with sheet metal enclosures single pole including one MCB 20Amp, 240 Volts, 10KA complete all as specified and directed. |
| 23 | S&F sheet metal enclosures for MCB distribution board 230V, SPN, 8way, double door type flushed inside wall with 200A rates bus bar and making good the disturbed surfaces complete all as specified and directed. |
| 24 | S&F SPN 32Amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commisioning complete all as specified and directed. |
| 25 | S&F 240V, 10KA \"C\" curve miniature curcuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
