Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 2 | M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in plinth protection, joints filled with bitumen sand mixed 50mm thick, finished even and fair without using extra cement, complete all as specified and directed. |
| 3 | M&L plain cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregates), 25mm thick as in flooring, complete all as specified and directed. |
| 4 | M&L non-skid ceramic coloured designer pattern tiles 300x300mmx7mm thick in floors etc.set jointed in neat cementslurry and pointed in white cement or coloured cement to match etc, including screed bed or bedding layer of mortar 15mm thickin cement mortar 1:6,with cement mortar bedding but not backing and removing, complete all as specified and directed. |
| 5 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 6 | S&F non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, on vertical surface such as skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, ncluding screed bed or bedding layer of mortar 15mm thickin cement mortar 1:6, with cement mortar beddingcomplete all as specified and directed. |
| 7 | S&F non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of eachtile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, ncluding screed bed or bedding layer of mortar 15mm thickin cement mortar 1:6,with cement mortar beddingcomplete all as specified and directed. |
| 8 | M&L for glazed ceramic coloured tiles of size 450x350x7mm thick,(premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and as directed. |
| 9 | M&L for machine cut kota stone slab flooring 16-18 mm thick over 20 mm thick cement mortar 1:6 screed bed laid and jointing with grey cement slurry mixed with pigment including rubbing and mirror polishing complete with machine all as specified as on stair shelves etc, complete all as specified and as directed . |
| 10 | M&L for machine cut kota stone slab 16-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, and including rendering 10mm thick in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge. |
| 11 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., complete all as specified and directed. |
| 12 | M&L for rounding to edges of stone slabs on edge, such as in steps, cooking platform and other similar situations, complete all as specified and directed. |
| 13 | M&L for sunken floor/ slab with the following specifications:-(a)Demolition of PCC and taking out old brick bat fillihng and roughening surfaces of old concrete floor and wall by picking, sweeping clean and washing down with water to remove dust etc. (b)PCC 1:2:4,type B-0, using 12.5mm graded stone aggregate averaging 50mm thick as in sunken floor,with proper slope towards GI spout. The dia of GI Spuot pipe shall be 32mm medium grade.The minimum length of Spout shall be 500mmand if any spout comes above chajja than the length of the spout shall be more than Chajja projection.Ends of Spout shall be tippered and any cutting through brick/ RCC structure shall be done by the Contractor and rates are deemed to be included of this aspects.(c) providing 15mm thick cement plaster in cement mortar 1:3 mixed with water proofing compound @ 3% by weight of cement over bottom and vertical surfaces finishing the surface even and smooth without using extra cement.(d) First layer of slurry cement @ 0.488 kg/ Sqm mixed with Acrylic based polymer modified cementations composite compound @ 0.253 kg/Sqm. The layer will be allowed to air cure for 4 hrs.(e) Second layer of slurry of cement @ 0.242 kg/Sqm mised with Acrylic based polymer modified cementations compound @ 0.126 kg/Sqm. The layer will be allowed to air cure for 4 hrs.(f) Graded Brick bats filling under sunken floor. (g)PCC 1:3:6,type C-1,using 20mm graded stone aggregate 75mm thick, over brick bats filling as in subbase to receive tiles. Note:- (i) For payment purpose only floor area shall be measured. (ii) After Coating of Water proofing compound ponding test shall be carried out by filling the sunken surface with water for 72 Hrs and get approved by Engr-in-Charge if any leakage/ seepage noticed the Contractor will re do the whole process without any extra payment.(iii) Cost of PCC , M-15, type B-1 (using 20mm graded crushed stone aggregates) for chamfering the edges and rounding the sides as directed by Engr-in-Charge shall also be deemed to be included in the quoted rates. |
| 14 | M&L for plain cement concrete M-5 (1:5:10), type E-2 (using 40mm graded crushed stone aggregate), as filling under (sunken slab) floors, complete all as specified and as directed. |
| 15 | M&L for grubbing up bushes, tree trunks portion not exc 30cm girth including cutting of trees/bushes grown in over wall and roofs digging out roofs and making good disturbed area of walls and roofs with plain cement concrete type C-1, 1:3:6 using 20mm graded crushed stone aggregates and matching to existing descriptions/ specifications, complete all as specified and as directed. |
| 16 | M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derustingand cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete 1:1.5:3 using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement mortar 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member n.exc 70mm incl necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete. NOTE: welded mesh shall be paid separately |
| 17 | S&F for hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement,complete all as specified and as directed. |
| 18 | Providing and fixing ceiling board of 4mm thick, designer, in ceiling fixed as per manufacturer’s instructions, including powder coated galvanised iron snap grid frame work of main and tee (weight not less than 240gm/Rm), angle (weight not less than 217 gm/Rm), grid size 595x595mm, for false ceiling all as specified, and hangers not less than 3mm nominal dia, galvanised iron (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of galvanised iron wire of 2.0mm dia, length as required at site and expansion hold fasteners 12.50mm dia, 40mm long including dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets,complete all specified and directed. |
| 19 | M&L for dismantling / taking down of existing roof treatment and roughening surface of old concrete roof by picking sweeping clean and washing down with water to remove dust etc and applying roof treatment with the following specification :i. Applying cement slurry over concrete surfaces @ 3Kg/Sqm ii. Rendering 15mm thick in cement mortar 1:4 mixed with water proffing compound as per manfactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and evn including curing the plastered surfaces for 7 days by ponding of water over the roof (leveling course)iii. Applying evenly one coat of cold bituminous primer conferming to IS 3384-1986 @ 0.40 Kg per Sqm on the cleaned plastered surfacesiv. Applying evenly one coat of blown hot bitumin of grade 85/25 @1.2Kg per Sqm primed surfacesv. Applying a layer of APP base polymerie membrane, 3mm thick (minimum) weighing 3.00 Kg per sqm reinforces) with polyster non woven fabric wighing not les than 160 gms per Aqm by torch application.The overlap shall be not less than 100mm on transverse direction and 75 mm on longitudinal direction and sealing overlaps.vi. applying two coats of aluminium paint, complete all as specified and as directed.Note: Cost of water proofing chemical shall be included in quote rate. |
| 20 | S&F in rapir tubes, \"medium grade\" galvanised, 15mm bore, ISI markedwith all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, including taking down existing pipe,complete all as specified and as directed.Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. |
| 21 | S&F in repair tubes, \"medium grade\" galvanised, 20mm bore, ISI markedwith all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, including taking down existing pipe,complete all as specified and as directed.Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates. |
| 22 | S&F in repair bib taps chromium plated fancy type, cast copper alloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed 15mm bore, complete all as specified anddirected. |
| 23 | S&F in repair wall mixer with provision of shower for mixing hot and cold water 3 in 1 fancy type brass chromium plated with long shank and cupscrewed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed 15mm bore fixed, complete all as specified and directed. |
| 24 | S&F in repair for basin mixer for mixing hot and cold water 2 in 1 fancy type brass chromium plated with long shank and cupscrewed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed 15mm bore fixed, complete all as specified anddirected. |
| 25 | S&F in repair 15mm angular stop cock with wall flange stainless steel/brass chromium plated, screwed down high pressure with or without lathered hot and cold with long screwed shanks and fly nuts, complete all as specified anddirected. |
| 26 | S&F in repair PVC connection 15mm bore size with PTMT nuts of length 45cm length, complete all as specified anddirected. |
| 27 | S&F in repair PVC valveless symphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including brackets 10 ltr capacity, complete all as specified and directed. |
| 28 | M&L for granite (of any type) work (table rubbed and polished), 20mm thick, in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed. |
| 29 | S&F for fancy brass chromium plated shower rose 125mm size, fancy type, fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. |
| 30 | S&F as in repair ball valve high pressure of PTMT with epoxy coated Aluminum rod & high density plastic ball screwed for iron pipe or brass ferrule 20mm bore, complete all as specified and directed. |
| 31 | Supply and fixing in repair 600x1200mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup waste washer, complete all as specified anddirected. |
| 32 | Supply and fixing in repair CP grating 150mm dia with centre hole, complete all as specified and directed. |
| 33 | Rotational moulded polyethylene water storage tank of 1000 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, including taking down existing storage tank, complete all as specified and as directed. |
| 34 | S&F in repair 15 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handle, complete all as specified and as directed. |
| 35 | S&F in repair vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts, flush pipe but excluding flushing cistern) and including plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and making good to dismantled/ damaged floor in cement concrete M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), complete all as specified and as directed . |
| 36 | S&F in repair vitreous china squatting pan, ‘Orissa’ pattern, size 580x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. but including concrete bedding layer, complete all as specified and as directed . |
| 37 | S & F in repair brass chromium plated tubular towel rail 20mm dia 600mm long with and including one pair of brass chromium plated bracket complete all as specifed and directed. |
| 38 | S&F in repair waste pipe for SINK/WHB/Urinal for 32/40mm dia, complete all as specified & as directed. |
| 39 | S&F in repair Vitreous china wash basin, of size 195x590x420mm oval shaped including waste coupling,waste pipe, cutting for and pinning in ends of brackets or erecting standporcelain stopper a pair of CI brackets fixed, complete all as specified and as directed . |
| 40 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed. |
| 41 | Taking down chowkhat or frame with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n.exc 4Sqm each, complete all as specified and directed. |
| 42 | M&L pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed . |
| 43 | M&L for plain cement concrete M-10 (1:3:6), type C-0, (using 12.50mm graded crushed stone aggregate), nominal mix, as in cills, steps; plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates and in hold fasts or filling in hollow of steel frame, including necessary form work, complete all as specified and as directed. |
| 44 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed. |
| 45 | S&F factory made steel window, box type, using ERW hollow \"P\" section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and plain sheet glass 3.0mm thick, 4mm thick frosted glass, jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD-1517/15, sheet No- 1/3 to 3/3 and as directed. Note :- Cost of window shall include all members and spare parts as elaborated in the Drwaing and in the specifications and nothing shall be paid extra seperately. |
| 46 | S&F factory made steel Ventilator, box type, using ERW hollow \"P\" section, comprising double frame for and including gauged and glazed skeleton shutter with wire mesh and plain sheet glass3.0mm thick, 4mm thick frosted glass, jointed internally and made with flat iron 40x4mm complete including grill/ guard bars of 8mm square bars fixed horizontally @100mm C/C including mild steel hinges, handles, tower bolts, stops, lugs etc, complete all as specified and as shown in drawing No- CEUZ/TD-1517/15, sheet No- 1/3 to 3/3 and as directed. Note :- Cost of window shall include all members and spare parts as elaborated in the Drwaing and in the specifications and nothing shall be paid extra seperately. |
| 47 | Supply and fixing of cupboard shutter 20mm thick (style) factory made pannel PVC including chowkat frame made out of M.S tubes 19 gauge for top and bottom rails M.S frame shall be covered with heated moulded plain colour PVC © channel having a PVC sheet strip of 10mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail and bottom rail on either side 10mm (5mmx2) thick of 20mm and 20mm cross PVC sheet and as gap insert for top and bottom rail. Pannelling for plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying fixing in the frame at site as per specification and drawing, complete all as specified and directed. |
| 48 | Sheet glass, 3.0mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane, complete all as specified and as directed. |
| 49 | S&F figured glass 4.0mm thick, pin head type glazed with oil putty in square not exceeding 0.50 Sqm in each pane, complete all as specified and as directed by Engineer-In-Charge. |
| 50 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded etc. with suitable PVC sheet beading including hinges etc, complete all as specified and directed. |
| 51 | S&F factory made, 35 mm thick plain framed panelled shutter (two panel) of second class hard wood rail and style with lock rail and panel of 9 mm BWP commercialply. The size of rail andstyle as per IS : 1003 Part I, klin seasoned and chemically pressure treated, complete all as specified and directed. |
| 52 | S&F glazed and skelton shutters using 2nd class hard wood 35mm thick open rebated and prepare to receive glass or gauge etc edges of framing plain and chamfered or fitted cut or mitered beads for securing glass size of member of shutter as specified in SSR Part-I section 8, clause 8.23(a) and divided in square, complete all as specified and as directed. |
| 53 | S&F in repair for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed. |
| 54 | S&F for mild steel square bar framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staging for of water tanks, cooler stand and similar work conforming to Fe-290, Gde-E-165, including cutting and welding, complete all as specified and as directed. |
| 55 | M&L for mild steel flat iron 40x6mm and struts in fencing including cutting tops to shape as directed, drilling holes, Fe 290 gde E-165 complete all as specified. . |
| 56 | M&L for preparation of new or previously untreated wood or wooden surfaces of any description, over 10 cement mortar in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed. |
| 57 | M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cement mortar width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and as directed . |
| 58 | S&F aluminium anodised barrel tower bolt ISI marked of extruded section and fixed, length of bolt 150mm, complete all as specified anddirected. |
| 59 | S&F aluminum alloy, anodized sliding door bolt ISI marked with hasp staple ( bolt type ) and fixing clips of sheet, castor extruded sections and fixing bolt and sliding boltof extruded section or cast aluminium alloy 250 mm long, complete all as specified and directed. |
| 60 | S&F extruded aluminum alloy handles 150mm ISI marked size fabricated type anodized, complete all as specified and as directed. |
| 61 | S&F mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, ISI marked, complete all as specified and as directed. |
| 62 | S&F floor doors stopper of aluminium alloy body and tenque anodised ISI marked with hard drawn steel spring fixed in floor 150mm long, complete all as specified and directed. |
| 63 | S&F butt hinge, ISI marked, medium weight cold rolled mild steel 100mm long to PVC door etc, complete all as specified and directed. |
| 64 | S&F as in repair epoxy powder coated rods of mild steel 25 mm with fixing brackets, pelmet rods including pair of fancy type finnals, complete all as specified and directed. |
| 65 | M&L for GI wire 6mm dia including fixingwith straining bolt and nuts with hook and necessary plain cement concrete and form work for mosquito net equal to length of barrack and 4 Nos line in each barrack, complete all as specified and directed. |
| 66 | Demolition brick work or stone/boulder masonry built in cement mortarincluding all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and precast concrete articles, complete all specified and directed. |
| 67 | M&L for brick work with sub class \"B\" bricks old size straight or curved in plane exc 6m mean radius built in cement mortar 1:6, complete all as specified anddirected. |
| 68 | Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 69 | M&L 15mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in cement mortar 1:6, complete all as specified anddirected. |
| 70 | M&L 5mm thick plastering on fair faces for concrete surfaces finished the surface even and smooth without using extra cement in cement mortar 1:3 on ceiling, complete all as specified and directed. |
| 71 | M&L 15mm thick plastering on fair faces of bricks or concrete surfaces finished the surface even and smooth without using extra cement in cement mortar 1:4, mixed with water proofing compound @ 3% by weight of cement, complete all as specified and directed.(Note: Cost of water proofing compound shall be included in item), complete all as specified and as directed. |
| 72 | M&L for preparation of new surface of wall with 3mm thick wall putty on plastered surface and applying two coat of oil emulsion white or coloured over a coat of primer of chalk whiteningon walls complete all as specified and as directed. |
| 73 | M &L for preparation of old surfaces of walls plastered surface, and applying two coats of exterior emulsion paint (Apex Ultima or equivalent), complete all as specified and as directed. |
| 74 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over coat of primer, complete all as specified and as directed. |
| 75 | M&L for preparation of complete removal of existing surfaces of wall and applying two coats of cement paint, complete all as specified and as directed by Engineer-In-Charge. |
| 76 | M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coat of white wash over onecoat of wall care putty of 3mm thick, complete all as specified and as directed. |
| 77 | M &L for preparation of new surfaces of walls plastered surface, priming with alkali resistant primer and applying two coats of exterior emulsion paint (Apex Ultima or equivalent), complete all as specified and as directed. |
| 78 | S&F Cast iron sand cast soil, waste and vent pipe, 100mm bore,in any length with or without ears, with cement joints, fixed on walls, including taking down, complete all as specified and directed. |
| 79 | S&F Cast iron sand cast soil, waste and vent pipe, 100mm bore,in any length with or without ears, with cement joints, in floors, including taking down, complete all as specified and directed. |
| 80 | S&F Cast iron sand cast soil, waste and vent pipe, 75mm bore, in any length with or without ears, with cement joints, laid in trenches or in floors, including taking down, complete all as specified and directed . |
| 81 | S&F Cast iron sand cast soil, waste and vent pipe, 75mm bore, in any length with or without ears, with cement joints, fixed on walls, including taking down, complete all as specified and directed. |
| 82 | S&F Cast iron bends, 100mm bore pipe (any radius), with duck\"s foot or heel rest, complete all as specified and as directed. |
| 83 | S&F Cast iron bends, 75mm bore pipe (any radius), with duck\"s foot or heel rest, complete all as specified and as directed. |
| 84 | S&F Cast iron branch pieces, 100mm bore pipe, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed. |
| 85 | S&F Cast iron branch pieces, 75mm bore pipe, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed. |
| 86 | S&F Cast iron branch pieces, 75mm bore pipe, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed. |
| 87 | S&F Cast iron bends, 100mm bore pipe (any radius), diminishing pieces or tapers (larger bore measured), fitted with oval access doors, complete all as specified and as directed. |
| 88 | S&F Cast iron bends, 75mm bore pipe (any radius), diminishing pieces or tapers (larger bore measured), fitted with oval access doors, complete all as specified and as directed. |
| 89 | S&F Cast iron branch pieces, 100mm bore pipe, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified and as directed. |
| 90 | S&F Cast iron ‘P’ or ‘S’ trap, with grating of 100mm outlet dia including jointing to waste pipe fixed in plain cement concrete, M-15 (1:2:4), type B-1 (using 20mm graded crushed stone aggregates), complete all as specified and as directed. |
| 91 | S&F 100mm cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and as directed. |
| 92 | S&F in repair 150 x 100 mm diastoneware Gully trapsetting and jointing with cement mortar 1:1, complete all as specified and directed. |
| 93 | Surface excavation not exceeding 30 cm and averaging 15 cm deep and getting out in any type of soil, complete all as specified and as directed. |
| 94 | M&L for hardcore of broken stone, gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and as directed. |
| 95 | M&L for 75 mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded stone aggregates as in sub bases of floors and pavings, complete all as specified and as directed. |
| 96 | M&L machine pressed precast concrete interlocking paver block of any size and shape confirming to IS 15658-2006 of 60mm thickness M-35 grade including 25mm thick sand cushioning, complete all as specified and as directed. |
| 97 | M&L for sand (cushioning) 25mm thickfilling under floors including watering and consolidation, complete all as specified and as directed. |
| 98 | M&L for demolition of cement concrete (reinforced) in any position and location and including cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed. |
| 99 | Precast reinforced cement concrete M-20 (1:1.5:3), type A-1, (using 20mm graded crushed stone aggregate), nominal mix, as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs and similar articles with plain faces as specified in clause No- 4.11.16 of SSR Part-I (2009), set in cement mortar 1:4, complete all as specified and as directed. |
| 100 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and direted |
| 101 | Excavation in trenches n exc 1.5 metre wide & n. exc 1.5metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes/cable/pipe line etc n. exc 10 Sqm on plan n. exc 1.5 metre in depth and getting out in any type of soil, complete all as specified. |
| 102 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) of 150mm/200mm internal dia, set in cement mortar, complete all as specified and as directed. |
| 103 | M&L for plain cement concrete M-10(1:3:6), type C-2 (using 40mm crushed stone aggregates) as in bed to drain pipes of 150mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; after laying, complete all as specified and as directed. |
| 104 | Salt-glazed stoneware drain pipes, internal 150mm, laid in trenches and jointed in cement mortar 1:1, complete all as specified and as directed. |
| 105 | Returning filling in including spreading, levelling , watering and well ramming of earth incl stone bouldersin layers not exc 25 cm, complete all as specified and as directed. |
| 106 | Removing excavated material to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5mtr above the starting point, complete all as specified and as directed by Engineer-In-Charge. |
| 107 | M&L for Plain cement concrete M-7.5 (1:4:8) type D-2 (using 40mm gradedstone aggregate), as in or as mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge. |
| 108 | M&L for plain cement concrete M-15 (1:2:4), type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in copings, kneelers, plinth courses, apex stones, bed plates,kerbs, mud stops, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work, complete all as specified and as directed by Engineer-In-Charge. |
| 109 | Cleaning of blocked/ choked SGSW/ Cast Iron drain pipes/ sewer lines of any dia and any types, in horizontal or vertical position by rodding, from manholes to manholes and manholes end to septic tanks/ soakage wells, flushing with pressure jet of water/ sewage suction machine after taking out existing manholes covers and putting back manhole covers in original position after cleaning of lines including removing the sludge and other waste materials/ blockage in drain pipes, transport to outside of Unit/ Cantonment area and spreading bleaching powder on top of manholes covers of septic/ soakage pits or in the surrounding areas to make hygienically fit, complete all as specified and as directed.Note: Cost of transportation of waste materials shall be deemed included in quoted rates. |
| 110 | M&L for bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces, complete all as specified and as directed by Engineer-In-Charge. |
| 111 | S&F vitreous China urinal, half stall,flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern and flush pipe but including of waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe, fixing in repairs, complete all as specified and as directed. |
| 112 | S&F vitreous china urinal partition white of size 310x700 mm urinal partitions slabs terminating about 40cm above floor line, complete all as specified and as directed. |
| 113 | Mild steel work as in desert cooler stand ornamental sections, rails and fastining and heavy bracket framing ( beam, tee, angle, channel, or flat section etc., confirming Fe 410 Gde 250, complete all as specified and as directed. |
| 114 | Dismantling plain or corrugated steel sheet etc roof coverings including ridge , complete all specified and directed. |
| 115 | S&f pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 116 | S&f pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 117 | M&L for structural steel work in roof trusses (framed), trussed, purlins, crane gantries, rails, water cooler stands, staging for water tanks, grills, gratings, fastenings, etc. and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-410-W (Grade E-250) quality A, including taking down existing steel work.complete all specified and directed. |
| 118 | Mild steel bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 30.0cm long, not exceeding 12mm dia of neck, complete all as specified and as directed. |
| 119 | Taking down carefully copper/aluminium point wiring ( light, fan, bell, socket or power, tube light ) complete,including fixtures and fittings such as switches, ceiling roses, holders, regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement for smooth finishing of holes,small patches etc, complete all as specified and directed. |
| 120 | Materialand labour for point wiring complete with 1.5 Sqmm PVC insulated, FRLSH type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copperconductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) andincluding cutting, chasing work at any height and all accessories are in concealedinwalls /roofs/floors / ceiling etc. flush mountingMS box with top,bottom,side/back wall knockout for conduitentry from any direction made out of 1.20mm thick suitable for fixing ofmodular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators, red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour), single core cable with copper conductor cable as earth continuity conductor andconnecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cementfor smooth finishing of existing surface, complete all as specified and directed for the following:-(Note:- Allnecessary accessories such asmodular box,top cover, plate, blank plate,MS box,screws,washers and all modular electrical fixtures are to be used same make/brand onlyand modular box,top cover plate, MS box shall be measured and paid seperately under relevant items) |
| 121 | (a) One light point/fan point/ exhaust fan point/ bell point controlled by one switch. |
| 122 | (b) One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board. |
| 123 | (c) One 5 pin 6 amps socket point controlled by one 6 amps switch on same board. |
| 124 | (d) One light point controlled by two 2 way switches. |
| 125 | Description all as per item No 120 above, but point wiring with 2.5 Sqmm and earth conductor of size 2.5 Sqmm complete all as specified and directed but for One 6 pin 16/6 amps socket outlet point controlled by one 16 amps switchon independent board, complete all as specified and directed. |
| 126 | Supply and fixing switch modular type, single pole, one way, 10 Amps, 1/2 module, 240v, ISI marked, complete all as specified and as directed. |
| 127 | Supply and fixing switch modular type, single pole, two way, 10 Amps, 1/2 module, 240v, ISI marked, complete all as specified and as directed. |
| 128 | Supply and fixing socket outlet, modular type 2/3-pin, 6-Amps, 2 module, complete all as specified and as directed. |
| 129 | Supply and fixingsocket, modular type, 6-pin, 6/16-Amps, complete all as specified and as directed. |
| 130 | Supply and fixing switch modular type, single pole, one way, 16 Amps, 1/2 module, 240v, ISI marked, complete all as specified and as directed. |
| 131 | Supply and fixing ceiling rose, three phase/ PVC/ polycarbonate, isolated body type, complete all as specified and as directed. |
| 132 | Supply and fixing lamp holder, PVC Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. |
| 133 | Supply and fixing LED bulb lamp of 9 Watt, 240volts, 50 Hz ,complete all as specified and as directed. |
| 134 | Supply and fixing inverter based LED tube light fitting, 20 Watt, 4 feet long indoor decorative high lumen batten 230 Volts, AC 50 Hz, 6500K, polycarbonate channel with lithium battery with back up time up to 4 hours and connecting up with twin core twisted flexible copper cable, complete all as specified and as directed. |
| 135 | Supply and fixing LED tube light fitting, 20 watt, 220 volts, AC decorative box type with driver holder, includingLED tube light connecting up with three core flexible copper conductor cable of suitable sizefrom ceiling rose, complete all as specified and directed. |
| 136 | Supply and fixing LED light fitting mirror type with the high out put diffuser 2 feet, 10 Watt, 220 volts, AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 137 | Supply and fixing in repair LED secruity light fitting of capacity 35 Watt in aluminium PDC housing, toughened glass cover with IP66 protectionwith suitable inbuilt surge protector with bracket made of GI pipe 40mm dia light grade 1.0 mtrs long duly cut and welded at an angle of 120 degrees and fixed to wall with 50mm X 6mm MS clamps-02 nos with 16mm dia bolts,nuts and washers, complete all as specified and as directed . |
| 138 | S&F in repair Ceiling fan, metalic, sweep 1200mm, with BLDC Motor, high speed, inclduing necessary fitting/fixtures such as Hook and clamps etc including connectig wire of suitable size and length from ceiling rose to fan connector, having BEE Star Rating- 5 Star, Rated Power Input in Watt 28±10%, Rated Speed in RPM 345±10%, Rated Air Delivery in CuM/ Min- 210 Minimum, Service Value CMM/W 7.85 Minimum No of Speed 5 , Insulation Class- E, Temperature Rise @ Rated Voltage 25 degree Celcius (Max) by winding resistance measurement at an ambient 30 degree Celcius, High Voltage Test Withstands 1.5KV, Insulation resistance above 2 MΏ, Type of Ball Bearings Single row deep groove ball bearings of 6202 sizes Top &Bottom Cover should be of aluminium, Type of Lubricant Used Lithium Based – Shell Alvania RL3, Material of Blade Aluminium, BEE Certification, Material of Canopies- Polypropylene, complete all as specified and as directed. Note:- (ii) The dismantled/unserviceableceiling fan shall be deposited with MES store yard for safe custody and shall be the property of the department. |
| 139 | Supply and fixing in repair of exhaust fan 300 mm sweep steel body with louvers,240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable of suitable size, nut bolt and other fixing material complete all as specified and directed.Note: (i) Cutting of walls/wooden panel of any description and making provision of holes etc and making good to the disturbed surface to matching with the existing finish shall also be deemed to have been included in the quoted rates. (ii) The dismantled/unserviceableexhaust fan shall be deposited with MES store yard for safe custody and shall be the property of the department. |
| 140 | Supply and fixing sheet metal enclosure DB TPN 4 way double door made powder coated out of CRCA, 1.6mm thickmild steel sheet 415 Volt , 200 amps rated bus bar dust and vermin proof suitable for incorporation of MCCB and MCBs duly concealed in wall and making good to disturbed surface complete including dismantling existing DB, complete all as specified and directed. |
| 141 | S&F sheet metal enclosures DB\"s double door factory made power coated out of CRCA mild steel sheet 1.6 mm thick with metallic painting white series, 240 volts 200 amps rated enamelled bus bar 8 way dust and vermin proof proof suitable for incorporation of MCBs duly concealed in walls and making good to disturbed surface and colour matchingcomplete including dismantling existing DBs, complete all as specified and directed. |
| 142 | S&F MCB SP 6 to 32 Amps 10 KA,\"C\" series, AC, 240Volts, 50Hz , ISI marked, complete all as specified and directed. |
| 143 | S&F MCB SPN 32 Amps 10 KA,\"C\" series,AC, 240Volts, 50Hz, ISI marked, complete all as specified and directed. |
| 144 | S&F MCB TPN63 Amps 10 KA,\"C\" series,AC, 415Volts, 50Hz, ISI marked, complete all as specified and directed. |
| 145 | M & L for sub main wiring complete with 2 run of 6.0Sqmm single core copper conductor (ISI marked)cable1100 volts grade, FRLSH type, PVC insulated, unsheathed,flexible,multi strandedcolour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such asBend,Tee,Elbow,Short peices etc concealed in wall/roofs/floorsand including cutting chases and making good the surface, one run of 6 Sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat and applying putty including cutting and chasing andcomplete all as specified and directed. including taking down existing wire.Note : - 2 run of 6 Sqmm single core copper conductor cable and one run of 6 Sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit only, complete all as specified and as directed. |
| 146 | M&L for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres belowground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipeof 15 mm diafrom earth electrode up to test point or up to 7.5mtr whichever is less by means of GIbolts, nuts, check nuts and washersall as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, plain cement concrete earth pit chamber 1:3:6 type C1, of size 45X 45X 45 cement mortar, RCC cover 1:2:4 type B1 of size 45X45X6 cement mortar, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old unserviceable earthing item, complete all as specified and directed. |
| 147 | Supply and fixing in repair GI bracket pipe of size 40 mm dia medium grade of 1.0 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixedon wall surfaces and including suitable fabricate MS flat iron clamps of 25X6 mm thick -02 Nos suitable for fixing any places with nuts,bolts & washers including grouting on wall etc., complete all as specified and directed. |
| 148 | Supply and laying, connecting and testing for XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 25 Sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc., including taking down exixting cable any type and size all as specified and directed. (Excavation and earth work, sand cushioning, brick protection & GI pipe shall be measured and paid for separately), complete all as specified and as directed. |
| 149 | M&L for clean dry river sand in trenches/ducts for cushioning to cable, 8cm in depth before laying the cable and 15cm in depth after laying the cable, complete all as specified and directed. |
| 150 | M&L for sub class \"B\" brick of size 230x115x75 mm laid flat work length equal to width of brick on sand for protection of under ground cable, complete all as specified and directed. |
| 151 | M&L for in repair GI pipe 40 mm bore light grade fixing to wall or laying in floors for protection of cable complete existing pipe, complete all as specified and directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
