|
| 1 | Demolition of cement concrete unreinforced of any description andin any position, not otherwise specifically provided for complete all as specified and directed. |
| 2 | Material and Labour for cement concrete 1:2:4, type B-0, (12.5mm graded stone aggregate) for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platformfortanks wherever required complete all as specified and directed. |
| 3 | Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposal of the same to distance exceeding 50mtr but not exceeding 100mtr as and where directed and Material and Labour for 10 mm thick screeding / rendering in cement mortar 1:3 on concrete roof surface, using Water Proofing Compound @ 3% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed.Note: Water Proofing Compound shall be measured and paid separately. |
| 4 | Supply only intergral water proofing compound complete all as specified and directed. |
| 5 | Material and Labour for Cutting out cracks to \"V\" section in existing roofs or terracing, cleaning out wetting grouting with cement and sand slurry 1:3 complete all as specified and directed. |
| 6 | Material and Labour for cleaning the plastered /concrete surface with wire brush and applying water proofing treatment complete all as specified and directed as under:-(a) Apply a uniform coat of primer at 0.70 kg/sqm over cement plaster.(b) 3 mm thick and weighing not less than 3.6 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen - based prefabricated five layer water proofing membrane reinforced with non woven polyester matt black finished over compatible primer at 0.40 Ltr/sqm of density at 25 degree centigrade 0.87 to 0.89 kg/litre and viscosity 70 to 160 cps or cold sticker and torch application of membrane with 10 cm overlap both ways after necessary preparation of surface complete as per manufacturers instructions. (c)Apply two coats of bitumastic - aluminium paint over the membrane. |
| 7 | Demolition of cement concrete (unreinforced)in ground floors and pavings n exc 15 cm thickness (below or above ground level ) complete all as specified and directed. |
| 8 | Material and Labour for waterproofing treatment to RCC sunken slab complete all as specified and directed. Make: PIDILITE , Dr Fixit or equivalent.(a) Clean the sunken portion of toilet/Bath/WC/Kitchenthoroughly toremove laitance, dirt , dust etc (b) Form angle fillet of size 40 mm x 40mm along thejunction of wall and floor using polymer modified mortar (\"Dr Fixit\" Pidicrete URP\" or equivalent)(c) Sanitary pipes entering through walls and floor shall be sealed with \" Dr Fixit Bathseal Tape\" and the gaps to be grouted with non-shrink cementitous grout \" Dr Fixit Bathseal Gruot\" or eqvt. Nahani traps , etc to be fitted securely and the gaps around it to grouted in the same manner.(d) Apply one coat of a Bitumen- modified polymer coating \" Dr Fixit Bathseal Plus\" or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet.Apply second coat of the same coatingon the angle fillets and allow it to dry completely.(e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first coat is dry.Extend the coating upto 150mm above the FFL.Above FFL,another cementitious waterproof coating \" Dr Fixit Pidifins 2K\" or eqvt can be further applied right upto 2.1 mtr to waterpoof the shower area also ,if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6 to 8 hours allow to dry completely.(f)After 2 to 3 days, sunken portion must be overlaid with a 50mm thick concrete screed M 15 type B0 (12.5mm graded stone aggregate) mixed with integral WPC (Liquid) laid to slope 1:60 towardsouter face of wall.Provide 40mm OD UPVC pipe at the lowest point with 300mm projectionbeyond the outer face of the wall.Then fill up the sunken portion with lean concrete 1:5:10 type E2 (40mm graded stone aggregate) complete all as specified and directed.(g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of appd makes such as Dr Fixit, FOSROC , SIKA, MC BUCHEMIE, ROFF etc , all as specified and directed.(Note:- Tiling work will be measured and paid separately) |
| 9 | Material and Labour for PCC (1:5:10) type E2using 40mm graded stone aggregate as inmass concrete or as in sunken portion or floorcomplete all as specified and directed. |
| 10 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat)complete all as specified and directed. |
| 11 | Material and Labour for 25 mm thick PCC 1 :2 : 4 type B0 ( Using 12.5 graded stone aggregate ) as inbase of floorscomplete all as specified and directed. |
| 12 | Material and Labour for Non Skid coloured ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in CM (1:6)Screed bed or bedding layer of mortar for laying floor finishescomplete all as specified and directed. |
| 13 | Material and Labour for Coloured Glazed ceramic tiles 450mm X 300mm X 7mm thick, on vertical surfaces such as skirting, dados and risers to stepsetc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 14 | Material and Labour for Coloured ceramic tiles 8mm to 10mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc,set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile laid over and including 15 mm thick screed in CM 1:6 all complete all as specified and directed. |
| 15 | All as per item No 13 above but as in skirting over 10 mm thick rendering in cm 1:4 complete all as specified and directed. |
| 16 | Demolition of brick work or stone masonary or block masonry built in cement or cement/lime mortar complete all as specified and directed. |
| 17 | Material and Labour for PCC solid block masonry of blocks of type C1 (20mm graded stone aggregate) (1:3:6) wallexceeding 10cm in width & built in CM (1:6) complete all as specified and directed. |
| 18 | Dismantling of old stone slab of any description complete all as specified and directed. |
| 19 | Material and Labour for 20mm thick Granite slab machine cut inlaid over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishingcomplete including screed bed 15mm thick in CM 1:4 complete all as specified and directed. |
| 20 | Material and Labour for 20mm thick Granite slab machine cut indado/skirting over cement screed and jointed with grey cement slurry and pointed with whiteor colour cement with admixture of pigment to match the shade of granite stone including cutting and polishingcomplete including rendering of 10mm thick in CM 1:4 complete all as specified and directed. |
| 21 | Material and Labour for 20mm to 25mm thk machine cut cuddappah stone as inslab flooring over cement screed bed laid and jointed with grey cment slurry mixed with pigment to match the shade of the slab incl grinding polishing laid over and including 15 mm thick screed in CM 1:6 complete all as specified and directed. |
| 22 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 23 | Material and Labour for machine cut kota stone slab flooring 20mm to 25mm thick in flooring but one piece as in treads of straircase etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed or bedding in CM 1:6 for laying floor finishes complete all as specified and directed. |
| 24 | All as item No 23 here in before but in skirting but one piece for step riser over and including 10 mm thick rendering in CM 1:4 to receive kota stone/slab etc complete all as specified and directed. |
| 25 | Taking down cement or cement lime plaster onbrick or stone walls,ceilings etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 26 | Material and Labour for 15 mm thick plastering in cement mortar 1:4 on external plaster finished the surfaces (upto any height) using 3% of WPC of weight of cement used or as per manufacturer instruction complete all as specified and directed.Note:- WPC shall be measured and paid separately. |
| 27 | Material & Labour for preparation to new surface andapplying finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. |
| 28 | Material and Labour for complete removal of existing treatment, preparing the surfaces and applyingfinishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)complete all as specified and directed. |
| 29 | ditto all as in item No. 26 above 10mm thick in CM 1:4 finished even & smoothwith thin layer of sagol finish but as in ceiling complete all as specified and directed. |
| 30 | Material and Labour for applying three coat of white wash on ceiling including preparation of new surfaces complete all as specified and directed. |
| 31 | Material and Labour for applying one coat of white wash on celing on old surfaces including preparation of old surfaces including cleaning smoke efflorocense of any type or spot of nail filled with putty complete match to old surface complete all as specified and directed. |
| 32 | Material and Labour for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a thin layer of sagol complete all as specified and directed. |
| 33 | Material and Labour for preperation of new plastered surfaces & applying two coats of oil bound distember over and including a coat of alkali resistant primer over and including a coat of putty complete all as specified and directed. |
| 34 | Material and Labour for complete removal of existing finishes and applying two coats of oil bound distemper on walls over and including a coat of alkali resistant primer including chalk whiting preparation of old surfaces , on plastered surfaces prepratary to distempering complete all as specified and directed. |
| 35 | Material and Labour for preparation of new surfaces ofwall andapplying threecoats of white wash on wallscomplete all as specified and directed. |
| 36 | Material and Labour for complete removal of existing finishes and applying threecoats of white wash on walls including preparation of old surfaces complete all as specified and directed. |
| 37 | Taking down chowkats or frames with shutters (without taking off shutters from the frames)exc 1.50 sqm but n. exc 4.00 sqm complete all as specified and directed. |
| 38 | Supply and Fixing Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed. |
| 39 | Supply and Fixing pressed steel frame of size 105mm x 60mm made outof 1.25 mm steel sheet fordoors with one or more rebatesincluding necessaryfixing lugs , hinges , lock strike plate etc complete all as specified and directed. |
| 40 | Material and Labour For PCC 1:3:6 type C0, (12.5 mm graded stone aggregate) in door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures complete all as specified and directed. |
| 41 | Material and Labour for flush shutters 35mm thick solid core constructions with block board core, ply wood face panelscommercial type on both side complete all as specified and directed. |
| 42 | Supply and Fixing in repairs 35mm thick factory made second class hard wood plain, framed , panelled shutter(2 panel) with lock rail and panel commercial ply or 12 mm veneered particle board of 9 mm B.W.P commercial veneering on both faces.The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 43 | Supply and Fixing in repairs 35 mm thick factory made Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a) complete all as specified and directed. |
| 44 | Supply and Fixing Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed length of bolt 250 mm complete all as specified and directed. |
| 45 | Supply and Fixing 150 mm size Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed. |
| 46 | Supply and Fixing Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fix 150mm long complete all as specified and directed. |
| 47 | Supply and Fixing in repairMild steel Butt hinges 100 mm long, medium weight, cold rolled steel complete all as specified and directed. |
| 48 | Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces complete all as specified and directed. |
| 49 | Material and Labour for applying one coats of synthetic enamel paint on old wooden surfaces of width or girth exceeding 10 cm including preparation of surfaces complete all as specified and directed. |
| 50 | Taking down shutter from frameexc 1 Sqmand n.exc 2 Sqm each and removing from the site complete all as specified and directed. |
| 51 | Supply and Fixing Solid PVC door frame of size 50mm X 47mm made out of 5mmthick plain colour PVC sheet reinforced with MS Square tube suppling and fixing in opening as per specification and drawing. |
| 52 | Supply and Fixing MS Butt hinges 75mm long, medium weight, cold rolled steel complete all as specified and directed. |
| 53 | Supply and Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails.M.S frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip if 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bootom rail on either side & as gap insert for top rail and bottom rail ; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles. & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 54 | Supply and Fixing Aluminium, anodised, barrel tower bolts of extruded section 125mm long complete all as specified and directed. |
| 55 | Supply and Fixing Aluminium handles, cast type, anodised size 125 mm long complete all as specified and directed. |
| 56 | Supply and Fixing Powder coated aluminium windowsliding type (3 track) with frame size100mm x 35mm x 1.2mm and shutter 39.40mm x 17.70mm x 1.2mm with two glass shutter & one mesh shutter incl necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with 4mm plain float glass & 0.36 mm dia SS wire mesh & 1.40mm average width of aperature, fittings etc including taking down old steel window complete all as specified and directed. |
| 57 | Supply and Fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixing to new steel window with nut bolt, fixed complete all as specified and directed. |
| 58 | Material and Labour for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enameled paint over and including a coat of red oxide, primer complete all as specified and directed. |
| 59 | Supply and Fixing Powder coated aluminium louvered ventilators of section size100mm x 25mm x 1.50mm including frosted glass 4mm thick fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh 0.36mm dia & 1.40mm average width of aperature fixed type on outside frame etc. including taking down existing steel ventilator complete all as specified and directed. |
| 60 | Material and Labour for preparation of old steel surfaces exc 10 cm width or girth and applying one coat of synthetic enameled paint complete all as specified and directed. |
| 61 | Supply and Fixing in repairs powder coated aluminuium pipe 20 mm dia as in curtain rod fixed to brackets complete all as specified and directed.Note:- Brakets shall be measured and paid separately. |
| 62 | Supply and Fixingin repairs powder coated aluminium brakets fancy type for curtain rods of 20mm dia complete all as specified and directed. |
| 63 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10cm girth complete all as specified and directed. |
| 64 | Taking up or down 15 mm bore steel tubing/Key tech pipeand connections including disconnection of fittings and cleaning for refixing where required complete all as specified and directed. |
| 65 | Ditto-all as above Item No. 64 but 20 mm dia pipe etc complete all as specified and directed. |
| 66 | Supply and Fixing 15 mm bore of pipe medium grade steel tubes, galvanised with & including all fittings and fixed complete to concealed walls and ceilings or laid in floors complete all as specified and directed. |
| 67 | Supply and Fixing 20 mm bore of pipe medium grade steel tubes, galvanised with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed. |
| 68 | Dismantling water tanks of capacity exc 250 litres but n exc 500 litres and removing to store complete all as specified and directed. |
| 69 | Supply and Fixing rotational moulded polyethylene water storage tanks of capacity 500 ltrhoisted and fixed in position including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. |
| 70 | Supply and Fixing in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed. |
| 71 | Supply and Fixing in repairs 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipe complete all as specified and directed. |
| 72 | Supply and Fixing in repair 15mm bore, angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed. |
| 73 | Supply and Fixing in repair 15mm bore, stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union but fancy type with long shank and cup (concealed type) complete all as specified and directed. |
| 74 | Supply and Fixing in repairs 15mm dia fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 75 | Supply and Fixing in repairs CP two way bib taps screwed for iron pipe 15mm dia and fixed necessary fitting with and incl PVC connection complete all as specified and directed. |
| 76 | Supply and Fixing in repair,Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe15mm dia or union complete all as specified and directed. |
| 77 | Supply and Fixing in repairs fancy type heavy duty health faucet chromium plated (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hookfixing to 15 mm bore of pipe complete all as specified and directed (Make :Jaquar/Hindware/Cera/Prayag or equivalent). |
| 78 | Supply and Fixing PVC connections 15 mm size with PTMT nuts of 600 mm long complete all as specified and directed. |
| 79 | Supply and Fixingin repair PVC (SWR) pipes110mm dia, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed. |
| 80 | Supply and Fixingin repairPVC (SWR) pipes110mm dia, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 81 | Supply and Fixing in repair,PVC (SWR) pipes75 mm dia, single socketed in any length with rubber ring joints fixed and laid in trenches or floor complete all as specified and directed. |
| 82 | Supply and Fixing in repair,PVC (SWR) pipes75 mm dia, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 83 | Supply and Fixing in repair PVC (SWR) bends any radius, for 110mm dia pipe complete all as specified and directed. |
| 84 | Supply and Fixing in repair PVC (SWR) bends any radius, 75mm dia pipe complete all as specified and directed. |
| 85 | Supply and Fixingin repair PVC (SWR) branch piece, single (single Y) equal or unequal,for 110mm dia pipe complete all as specified and directed. |
| 86 | Supply and Fixingin repair PVC (SWR) branch piece, single (single Y) equal or unequal for 75mm dia pipe complete all as specified and directed. |
| 87 | Supply and Fixingin repair PVC (SWR), junction single, (Single T) equal or unequal,for 110mm dia pipe complete all as specified and directed. |
| 88 | Supply and Fixingin repair PVC (SWR), junction single, (Single T) equal or unequal,75mm dia pipe complete all as specified and directed. |
| 89 | Supply and Fixing in repairs wash down water closet ( European type) excluding fixing bolts, flushing cistern, & flush pipe but including connecting to existing out let pipe etc complete all as specified and directed. |
| 90 | Supply and Fixing in repair PVC valveless syphonic action type flushing cistern (Low level) of 10 litre capacity, coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed. |
| 91 | Supply and Fixing in repairs vitreous china wash basin white, flat back of size 450mm x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets complete all as specified and directed. |
| 92 | Supply and Fixing in repairs 15mm dia brass CP Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed of make CERA cat part No F 2010403 or techno commercially equivalent models in makescomplete all as specified and directed. |
| 93 | Supply and Fixing in repair pillar tapsfancy type cast copper alloy with capestan heads chromiun plated screwed down high pressurewith hot & cold with long screwed shanks and fly nutscomplete all as specified and directed. |
| 94 | Supply and Fixing in repair ,stainless steel sink with drainage board, 1mm thick, kitchen or laboratory with plugs, washers and waste; including PVC waste pipe, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 95 | Supply and Fixing in repairsfor 600mm x 450mm bevelled edge mirror of selected quality glass,mounted on 6mm thich AC Building board or commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. |
| 96 | Supply and Fixing plate rack made of stainless steel1mm thick and overall size 915mm x 915mm x 255mm, inlcuding taking down old /unserviceable complete all as specified and directed. |
| 97 | Supply and Fixing in repairs tubular towel rail 20mm dia, D type 60cm long between flanges brass chromium plated complete all as specified and directed. |
| 98 | Supply and Fixing in repair 100 mm dia cast iron floors trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 (20mm graded stone aggregate) complete all as specified and directed. |
| 99 | Supply and Fixing in repairs 18mm to19mm thick Prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed. |
| 100 | Supply and Fixing Contineous Piano hinged 30mm width of flaps (when open), mild steel, bright finish or electro galvanised complete all as specified and directed. |
| 101 | Supply and Fixing 100mm long Aluminium handles, cast type, anodised complete all as specified and directed. |
| 102 | Supply and Fixing in repairsgrating square or circular 125mm diaof PTMT (minimum weight 100 gms,complete all as specified and directed. |
| 103 | Dismantling wrought iron or mild steel work of any description not othervise provided complete all as specified and directed. |
| 104 | Supply and Fixing mild steel work in framed work such as grills framed guard bars, gratings, ladders etc with ends of bars shouldered and / or riveted or forged into spikes and similar work Fe290 Gde E-165 complete all as specified and directed. |
| 105 | Supply and Fixing in repairs 150mm rubber door stopper of aluminium alloy body, anodisedcomplete all as specified and directed. |
| 106 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed. |
| 107 | Material & Labour for point wiring complete with 1.5 Sqmmsingle core FRLS PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through and including non metallic rigid PVC conduit and accessories concealed in walls including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push complete all as specified and directed. |
| 108 | All as per item No 107 above but for one 3 pin 5 Amps socket on same board controll with other switches on same board complete all as specified and directed. |
| 109 | All as per item No 107 above but for one 3 pin 5 Amps socket on independent board complete all as specified and directed. |
| 110 | All as per item No 107 above but for one light point controlled by two way switch complete all as specified and directed. |
| 111 | All as per Item No 107 here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor forPower Socketon independent board on the existing concealed conduit complete all as specified and directed. |
| 112 | All as per Item No 107 here-in- before but with 4Sqmm PVC insulated multistranded copper conductor with 4 sqmm cable as earth continuity conductor forPower Socket/AC/Geysers on independent board on the existing concealed conduit complete all as specified and directed. |
| 113 | Supply and fixmodular switch 1 way 6A 1 module complete all as specified and directed. |
| 114 | Supply and fixmodular switch 2 way 6A 1module complete all as specified and directed. |
| 115 | Supply and fix modular bell push6A 1module complete all as specified and directed. |
| 116 | Supply and fix modular socket 6A2/3 pin combined 2 module complete all as specified and directed. |
| 117 | Supply and fix modular socket 16A2/3 pin combined 2 module complete all as specified and directed. |
| 118 | Supply and fix modular switch 1way16A 1 module complete all as specified and directed. |
| 119 | Supply and fix Modular fan regulator complete all as specified and directed. |
| 120 | Supply and fixelectric bell Ding Dong, AC 230 volts complete all as specified and directed. |
| 121 | Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed. |
| 122 | Supply & fix LEDfitting for Bldg security, 35 Watt230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete. including conncting with suitable size of copper conductor 3 core flexible cable from fitting connector to ceiling rose and fixon wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr lenth with necessary bending complete all as specified and directed . |
| 123 | Supply and fixing LED lights fitting 1x 20W, 220V,AC, decorative box type with driver, holder incl LED tybe light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 124 | Supply and Fixing wall/ceiling mounted LED tube light fitting , Energy efficient high quality invertor batten having Lithium ion battery of 3.7V, 19 WH for backup upto 2Hrs with high power brightness having BIS certification, LED fitting should be LM 80 certified with system efficacy greater than 100 lumens/watt, including LED tube 20/22 watt having colour temperature 6500 K (4 feets long) , PF> 0.95, THD less 10%, with IP20 protection having open and short circuit protection, having input voltage range 90V to 300V connecting with three core flexible copper wire from connector to ceiling rose/angle holder as per existing site requirement complete all as specified and directed. Make :Jaquar/Halonix/Philips .Note :- The rates are inclusive of cost of square box-02 nos including suitable size of clamps and screws etc. |
| 125 | Supply and fixing LED Light fitting mirror type with high output diffuser 2 feet , 1 X 10 watt 220 V ACdecorative type with driver holder and LED lamp, Alluminium housing,including connecting up with three core flexible copper conductor cable of suitable size completeall as specified and directed. |
| 126 | Supply and Fixing wall mounted high quality indoor wall bracket light cylinderical/oval shapeaesthetically designedfitting in wooden housing , glass and B22 holder complete includinginverter LED bulb B-22 cap with opal diffuser, IP-20 and inbuilt battery backup (LED INVERTER LIGHT 10W B22 CW IP) 10 watts including necessary eletric connection with PVC insulated multistranded copper cable of suitable size 3 core from ceiling rose to fitting terminal completeall as specified and directed. |
| 127 | Taking down unserviceable submain wiring and Material & Labour for submain wiring in PVC conduit with two runs of 6 sqmm and one runs of 6 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid connduit heavy grade ISI marked (IS 9537 Part III) includung accessories such as bends, supports etc all as specified and directed. Note: Two runs of 6 sq mm and one runs of 6 sqmm cable along with conduit shall be measured as one length complete all as specified and directed. |
| 128 | Supply and Fixing MCB DB SPN 8 way of any size and capacity double door type horizontal with 200A busbar including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed. |
| 129 | Supply and FixingMCB SP of capacity 5A to 32A \"B\" curve complete all as specified and directed. |
| 130 | Supply and FixingMCB, SPN (Double Pole) 32 amps, 240 Volts, 10 KA‘’C” curve complete all as specified and directed. |
| 131 | Material & Labour for earthing with 600mm x 600mm x 6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the plate at a depth of not less than 1.5mtr below ground level, connected to and including G.I. wire of size 4 mm diaby means of bolts,nuts and check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. incl charcoal dust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6 type C1 (20mm graded stone aggregate) & RCC Chamercover of size 540mm x 540mm x 100mm made with 1:2:4 Type B1 (20mm graded stone aggregate) using 6 mm round MS bar & 8 mm MS bar for handle ,20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and directed. |
| 132 | Taking down oldunsv Exhaust fan and depositing it to MES store and Supply and fix new Exhaust fan steel body AC single phase , 230 volts of size 380 mm sweep with blades and frame and louvers complete all as specified and directed.Note : (i) To be Fixed in Existing Kitchen window (ii) The rates are inclusive of any civil work required to fix the exhaust fan. |
| 133 | Taking down oldunsv exhaust fan and depositing it to MES store and Supply and fix Exhaust fan which is made up of PVC Plastic, AC single phase , 230 volts of size 300 mm sweep with blades and frame and louvers complete all as specified and directed.Note : (i) To be Fixed in Existing Toilet window (ii) The rates are inclusive of any civil work required to fix the exhaust fan. |
| 134 | Taking down oldunsv ceiling fan and depositing it to MES store and Supply and fixing new ceiling fans complete with blades, down rods, electronic regulator/remoteand connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 135 | Supply and fix singlepole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amp DP MCB complete all as specified and directed. |
| 136 | Taking down the existing serviceable kwh meter from site without any damagecleaning it properly and refixing the same in the new panel as directed by Engr-in-charge of the each block after completion of work complete all as specified and directed. |
| 137 | Supply, install testing and commissioning manufactured by CPRI approved manufacturer indoor type LT panel board wall mounted, self supporting compartmentalised design of suitable size but not less then 1.2 Mtr X 1 Mtr X 0.3 Mtr, 440 V 3 phase 4 wire system powder coating provided with suitable to make it dust/vermin proof. The panel shall be made with 2 mm thick CRCA sheet for outer shell and inner shell made out of 1.6 mm thick CRCA sheet,double door with front openable with locking arrangement, provision of threaded earthing stud at bottom, inner shell be compartmentalized, front openable single door system lockable. Inner shell completely vermin proof and to accommodate incoming/outgoing MCCBs, MCBs and TPN aluminium bus and extension links. Aluminium bus bar of capacity 300 Amps- 4Nos,including neutral duly insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size/rating of epoxy resininsulator all housed in suitable bus bar chamber.All control wires shall be with 2.5 sqmm multi stranded copper conductors and shall be properly bunched,tied, ferrulled for proper indentification and crimped with adequate size of lugs andprovision and fixing of Voltmeter,Ammeter with built in selector switch, CTs of suitable ratio, and pilot indication lamps completealong with provision of necessary cable entry/exit boxes for all incoming and out going cables with suitable size of cable glands etc. Computer cut shelf adhesive vinyl danger notice plate having conventional symbol of bone & skull be provided. The panel shall consists of following accessories:-Location :- (P-37 bldg BDTC) |
| 138 | i) Incomer a) MCCB four pole 25 KA rapturing capacity 100 Amps Ics= 100% of Icu thermal magnetic setting including connection with bus bar- 01 Nos(as incomer)ii) Out going a) MCB SPN 40 Amp 10 KA \"B\" curve-9 Nos (out going )01 for each Qtr b) MCB SPN 10 Amp 10 KA \"B\" curve-01 Nos (out going )(for staire light and Bldg/S/Light) c) Voltmeter0 to 500voltsof size (square dialed) 96 X 96 sq mm flush mounted, AC 50 Hz three phase energy accuracy class 1.0 including inbuild selector switch - 01 Nosd) Ammeter 0 to 100 amps of size 96 X 96 sq mm flush mounted, AC 50 Hz three phase energy accuracy class 1.0 including inbuild selector switch and suitable ratio of CT\"s complete - 01 Nos e) LED type RYB phase indicator lamp with back up HRC fuse- 01 Set f) Suitable space for fixing 10 No\"s single phase smart energy meter. |
| 139 | Supply and Fixing Vigi Guard Boom Barrier GVB6 - Boom length (mt) - 4.00, Height of Boom from Ground (Approx MM) - 875, Housing Dimensions (Approx. mm) 400x400x1065, Boom Dimensions (mm) - 90x32, Controller Protecting Rating - IP54, Control Panel power supply (v) - 230 A.C. 50/60 Hz, Motor Power Supply (v) - 24 D.C. Power (W) - 200, Opening Time (Sec) - 2 to 4, Duty Cycle - 100% Intensive Use, Operating Temperature (C) - (-)20 To (+)55, MCBF - 5 Million Cycle complete all as specified and directed. |
| 140 | Supply and Fixing Photocell - IR Obstacle detection sensor - Anti crush safety sensor for vehicles complete all as specified and directed. |
| 141 | Providing, transporting, assembling and erecting factory-made pre-fabricated security cabin of approved make, complete with structural steel framework fabricated from MS tubular sections, duly welded, bolted and treated with one coat of red oxide zinc-chromate primer and two coats of synthetic enamel paint. The cabin walls and roof shall be made of PUF / EPS insulated sandwich panels (minimum 40 mm thick) with pre-painted GI sheets on both sides. Roof shall be slightly sloped with proper rainwater drainage arrangement.The cabin shall include: • Powder-coated aluminium / uPVC glazed windows with clear glass • MS / aluminium flush door with lock, handle and stopper • Cement board / vinyl / chequered PVC flooring • Internal electrical wiring with one LED light fitting, one exhaust fan, one 5A switch socket, MCB, earthing and external power connection complete • Necessary nuts, bolts, sealants, flashings and finishing worksThe cabin shall be erected over PCC / RCC platform (platform paid separately unless otherwise specified), complete all as specified and directed.Size: 1.8mtr × 1.8mtr× 2.4mtr |
| 142 | Civil Work complete all as specified and directed. |
| 143 | Installation Charges for Boom Barrier (per Boom Barrier) one time complete all as specified and directed. |
| 144 | Cable complete all as specified and directed. |
| 145 | Tranportation Charges complete all as specified and directed. |
