Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking down existing roof treatment and all loose and de-bonded concrete/ screed, loose particles, dirt etc & Debris should be removed from Bldg. Roof substrate must be pressure-washed with water with, a minimum working pressure of 1,400 psi is to be used to and/or remove all dirt, dust, chalking and waste products. Remove algae, mold by using bleach solution or biowash etc complete all as specified & directed. |
| 2 | M&L for repair of all visible hairline cracks on concrete roof / screed more than 0.50 mm and not giving hollow sound, should be cut and widen in V shape with mechanical cutter in the size (10mm W x 6mm D). Fill cracks withPU sealant / Hybrid Sealant with suitable gun and smoothed with a putty knife or trowel. Allow sealant to cure a minimum (72 Hrs.) 3 days etc complete all as specified & directed. |
| 3 | M&L for Remove loose and damaged concrete roof screed in pockets with mechanical cutter. Clean the concrete screed with high pressure water jet to remove dirt and loose particles. Brush apply a bond coat ofPidicrete URP mix in the ratio of 1:1 (URP 1: Cement 1) by volume to make it lump free slurry when applied on in the pre wet surface. Laid to fall roof screed in correct slope and gradient. Mix Dr. Fixit Pidicrete URP 10% by weight of cement in (M20) concrete in ratio of 1:1.5:3 i.e., one bag of 50kg cements: 1.5 times volume of sand: 3 times volume of aggregates: 25L water. Level the repair mortar and finish with trowel average 25mm thick. Moist cure should be done for 7days. Air cure screed for 7days, before application of roof top coat coating system etc complete all as specified & directed. |
| 4 | Applying one coat ofCipoxy 16D primer in the ratio 1:1 spreading at the rate of 0.200 kg-0.250 kg /sqm in complete dry condition where moisture contain below 7% (should be checked with moisture meter)Allow the primer coat to dry for 6 to 8 hours. Apply 1st coat ofRoofseal Classic without dilution spreading at the rate of 0.70/litre/Sq.mt/Coat until all surface is covered. Lay a 45 GSM Fibre glass mesh as a reinforcing material which is incorporated in the coating when the first coat is still in wet condition. Allow the first coat to dry for approximately 4 to 6 hours. Apply the second of chemical with the same application coverage, but in a direction perpendicular to that of the first and second coats. Allow each coat to air cure for a minimum of 4-6 hours after application. Check to see no void surface is left untreated / uncoated.Allow the system to air cure for 7 days minimum etc complete all as specified & directed. |
| 5 | Dismantling floor, hearth wall tiling including cement mortar bedding (but not backing) including rubbish off the premises complete all as specified and directed. |
| 6 | M&L for Virified colour Ceramic joint free tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ceramic coloured tiles joint free decorative (square/ rectangular) area of each tilessqm in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6.complete all as specified and directed. |
| 7 | M&L for Virified colour joint free ceramic tiles 10 mm thick (square/ rectangular)polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm in skirting/vertical surface etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed. |
| 8 | M&L for7 to 8 mm thick non skid ceramic coloured tiles joint free(square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6.complete all as specified and directed. |
| 9 | M&L for Coloured Glazed ceramic tiles 450x350x7mm thick, on vertical surfaces such as skirting, dados and risers to stepsetc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed. |
| 10 | Dismantling stone slabsof any description or thickness in floors / dados, etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 11 | M&L Granite 20 mm thick in steps, pillars, window cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rounding edges of stone slab one edge and including 20 mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and as directed. |
| 12 | M & L for machine cut Kota stone slab flooring 20-22mm thick over 15mm thick screed bed in CM 1:6. laid and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 13 | M & L for kota stone slab 20-22 thick in riser of steps, skirting, dado and pillar laid over 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 14 | Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 15 | M&L brick work with sub class \"B\" bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 16 | All asitem no 15 abovebut except bricks complete all as specified and directed. (Note:- Bricks obtained from item No 14 shall be reused after cleaning.) |
| 17 | Taking down cement / lime plaster,and any kind wall cladding tiles/brick stone of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for kay, scrubbing down with water complete all as specified and directed. |
| 18 | M &L for 10 to 12mm smart care ready mixplaster is a specially designed ready to use cement-based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over interior wall surfaces complete all as specified and directed. Note: Coverage for smart care ready mix plaster shalll be 24 - 28 kg / sqm). |
| 19 | M &L for 10 to 12mm smart care ready mix repair plaster is a specially designed ready to use cement-based plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacture instructions) over exterior wall surfaces complete all as specified and directed. Note: Coverage for smart care ready mix plaster shalll be 24 - 28 kg / sqm). |
| 20 | M & L for washed stone grit plaster on exterior walls in two layers , under layer 12mm th cement plaster 1:4 ( 1 cemant : 4 coarse sand ) furrowing the under layer with scratching tool , applying cement slurry on the under layer @3 Kg of cement per sqm , top layer 15 mm th cement plaster1 :1 / 2 :2 ( 1 cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size ) in panels with groove all arround as per approved pattern incl. scrubbing and washing the top layer with brushes and water to expose the stone shipping complete all as specified etc |
| 21 | Forming groove of uniform size 15 mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens nailed to the under layer incl. removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified & directed. |
| 22 | M&L for rendering 10mm thick in two coats each 5 mm thick plastering on concrete surfaces of ceiling/Chajja in CM 1:3, finished the surfaceeven & smooth complete all as specified and directed. |
| 23 | M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed. |
| 24 | M&L for preparation of old plastered/unplasteredsurfaces of ceiling and applying one coat of white wash complete all as specified and directed. |
| 25 | M&L for preparation of old / new decorated plastered/un-plastered surfaces of walls of any description,pillars, cornices by brooming down or steel wire brushing, scrubbing down smoke, soot, mould moss and efflorescent, salts, trading oil and greasy spots incl rubbing of putty surface and applying two coats of exterior acrylic emulsion paint(wheather Proof) of approved make for fungus protection on wall/roof/fecia over 2 mm wall care putty etc (External surface) of approved make of required shade and colour at any height of structure complete all as specified & directed. |
| 26 | M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed. |
| 27 | Material and Labour for preparation of old plastered or unplastered surfaces of wall including cornices, pilaster etc by brooming down by steel wire brushing, scrapping down smoke Soot, moulds, moss and trading oil and greasy spots etc and apply one coatof white wash complete as specified and directed. |
| 28 | Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed. |
| 29 | All as per item No 28 before but exc 1.5 Sqm and not exc 4.00 Sqm each complete all as specified and directed. |
| 30 | S&F Factory made single extruded WPC (wood polymer composite) solid door/window/ cesetory windows & other frames / chowkhat of decorative type/wood grain printed colour of size 50x125 mm comprising of virign PVC polymer of K value 58-60 (suspension grade) calciamCalcium carborate and naturan fibers (wood powder/ rice husk/ wheat husk ) and non toxic additives (maximum toxity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwd with full body threated star headed SS screw having minimum frame dencity of 750 kg/ cum. Srew withdrowl strenghth of 2200 N (Face) & 1100 N (Edge). minimum comp ressive strenth of proof. water/modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer froff water /moister proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasterners of required dia and lenth complete as per direction of Engineer-in-Charge. |
| 31 | Supply and fixing factory made single extruted WPC ( wood polymer composite ) solid decorative type/wood grain printed color flush door shutter of size 35 mm thick comprising of virson polymer of k value 58-60 (Suspension Grade ) calcium carbonate and natural fibers (wood powder/rice husk /wheat husk and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum dencity of 650 kg/cum and screw withdrowl srength of 1800 N (face) & 900 N (Edge). mimimum compressive strength 50 N/mm2, modulud of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof. water/molstrureproof and fire retardent. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including S & with stainless steen butt hinges of required size with neccesory full body treaded star headed counter sunk S>S screw complete all as specified and directed. |
| 32 | S & F for factory made wire gauged PVC door shutter 30mm thick ( style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be coverd with heat moulded decorative type/wood grain printed colour PVC \"C\" channel having a PVC sheet strip of20mm width stuck inside with sottom rail on olevent cement for stiles and wood grain printed a PVC sheet for top rail. lock rail & bottom rail on eighter side & as gap insertfor top rail & bottomrail. wire gauzed i. e panel will be of wire gauze in lieu of wood grain printed Pvc sheet PVC panel the wire gauze shall be wrapped on an additional square 8 mm M.S solid tube and this shall be welded to M. S tubes, The wire guaze shall be strectched to tighten firmly of wood grain printed colour PVC sheet to be fitte in the M.S frame welded/ sealded to the stiles & rails with suatable 5mm thick x 15mm wide PVC sheet beading used stiles and rails and decorated PVC beading of 10mm x 10mm (9000)used insted of exposed portion of PVC sheet beading and joined togather with solvent cement, suppling & fixing in the frame at site complete all as specified and directed. |
| 33 | M & L Mild steel farmed work as in doors (as in ckowkats/shutter frame) or gates of angle or other section with guest plates rail, brasses rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to GdeFe-410-W(Gde-E-250)quality-B including shop coat of red oxide including prepration of surface before fixing complete all as specified and directed. |
| 34 | M&L for Mild steel, plain, black sheet 1 mm thickin wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, ncluding bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 35 | S&F mild steel work for hold fast and similar small articles conforming to Fe 410-0 or Fe 310-0 including MS screws, bolts, including tarring with a coat of tar and sanding complete all as specified and directed. |
| 36 | S & F for framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 37 | S&F of factory made soild PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification and drawing complete all as specified & directed.. |
| 38 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 39 | S & F, factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed. |
| 40 | S & F factory made steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed |
| 41 | S & F for 3 mm thick sheet glass ordinary quality and glazing withoil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed |
| 42 | S & F in reapir for 3 mm thick sheet glass ordinary quality and glazing withoil putty in square not exc 0.5 Sqm in each pane including hacking out old broken glass from any type of framr complete all as specified and directed |
| 43 | S&F Eco-400 windows fabricated from roll formed sections of galvanized steel colour coated/powder coated (base steel as per IS 513\"D\" quality galvnized as per IS 277 with fine of 120 Gms / Sqm ) with total coated thickness of 0.60 mm sections should be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyster powder up to 50-60 microns, thick section for frame should be of 72mmx50mm,section for mullion should be 72x50 mm, section for shutter frame should be of 47x20mm, section for fixed glass bead should be of 12mmx12mm, and section for fly mesh should of 40x20 mm, each glazed shutter and mesh shuttershould be provided with SS pivot hinges -1 set sec color handle and stay, each glazed shutter and fixed glass portions should be provided with a glass of 5 mm plain float glass mesh shutter should be provided with stainless steel 32 mm guage fly mesh of 304 grade with 144 holes / sqm in window should be provided with grill made of 10 mm Sqr MS Bars welded to at 150mm centre to centre 6mmx12mm Ms flat. total grill unit should be powder coted and fixed to window frame with screws. |
| 44 | S&F 100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed. |
| 45 | M&L 100 mm long aluminium anodized handle cast type complete all as specified and directed. |
| 46 | S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed. |
| 47 | S&F Aluminium alloy, anodised, 200 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 48 | S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 49 | M&L for applying one coats of synthetic enamel paint over a coat of pink primer on wooden surface over 10 cm width or girth including preparation of old or previously untreated wood surfaces complete all as specified. |
| 50 | M & L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 51 | Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed. |
| 52 | M & L 75 mm thick Cement concrete type C-2, 1:3:6 (USING 40mm graded stone aggregate) as in plinth protection complete all as specified and directed. |
| 53 | M&L for providing, PCC 1:2:4 type B-1 (using 20mm graded aggregate) for embedding hold fasts/coping /padding including necessary form work etc.complete all as specified and directed. |
| 54 | S & F, 150mm floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 55 | S&Fdrapery (curtain)rod 25mm dia Stainless steel grade 304 approved quality and colour includingside cups,fixing arrangement with drilling holes in walls brackets etc complete all as specified and directed. |
| 56 | Taking up or down 15mm dia steel tubing and connections etc complete all as specified and directed. |
| 57 | S&F 15 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 58 | Taking up or down20mm dia steel tubing and connections etc complete all as specified and directed. |
| 59 | S&F 20 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 60 | Cutting Chases, pinning in brick/Concreate wall making good to facing where required and pointing in cement mortar 1:3 ends of edges of landing, steps cills sunshade shelves lintles etc and cutting chase for concealed water tubing or or concealed conduit wiring. etc and making good cutting N. exceeding 10 CM girth complete all as specified and directed. |
| 61 | S&F in repairs oval type wash basin superior quality 537x439 mm size incl fitted with granite top/baroda green stone over precast RCC slab including waste coupling and incl suitable size CPbottle trap connected upto grating complete all as specified and directed. |
| 62 | M&L for demolition of reinforced cement concrete of any description and in any position complete all as specified and directed. |
| 63 | M & L for Reinforcement cement concrete (Nominal Mix)type B11:2:4 (using 20mm stone aggregrate ) as in slab supported on wallfor wash hand complete all as specified and directed |
| 64 | M &bL forFormwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work and fair finished surfacenot exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 65 | Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and directed. |
| 66 | M & L Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 67 | All asitem No 66 abovebut 6 to 8mm dia complete all as specified and directed. |
| 68 | S & F vitreous china wash down water closed pan (Pedestal Pattern ) with \"P\" and \"S\" trapp including connection to trap and cistren and flush pipe (excl flushing cistren)and making good to disturbed surface of floor all fixed as in repairs all as specified and directed. |
| 69 | S&F in repairs vitreous China squatting pan (Orissa pattern), white, of size 580x440mm white, with CI \"P\" or \"S\" trap, integral foot rests including flush pipe, trap, lime concrete bedding inlcuding taking out of old lime concrete bedding, unserviceable connections etc connecting up new and making good disturbe portioncomplete all as specified and directed. |
| 70 | S&F in repairbib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orto GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed. |
| 71 | S&Fin repair 15 mm bore CP Angle valve two way fancy type with wall flane, highpressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed complete all as specified & directed. |
| 72 | S&F in repair15 mm bore, single lever brass chromium plated wash basin mixer wothout popup waste with 450mm braided hoses opal prime fixed to wash hand basin complete all as specified and directed. |
| 73 | S&F in repair 15 mm borestop cock, (Concealed type) cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule orto GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed. |
| 74 | S & F in repairs brass chromium plated shower rose 125 mm size, long body ( Arm size should not be less than 450 mm ) with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and directed. |
| 75 | S&F in repairs 600 x 450 mm bevelled edge mirror of selected quality glass 5 mm thick mounted on 6 mm thick commercial ply wood aluminium frame and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. |
| 76 | S&F in repair 500 ltrs capacity rotational moulded polyethylene white colour water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of water tankcomplete all as specified & directed. |
| 77 | S & F in repair of plastic wc seat cover and mild steel chromium plated or aluminised hinging device asetc complete all as specified and directed. |
| 78 | S & F in repairs Flushing Health Faucet for pedestal pattern WC incl .flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed. |
| 79 | S & F in repairsPVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 80 | S&F in repairs 10litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC connections 15mm size with PTMT nuts of length 450mm inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbe portion complete all as specified and directed. |
| 81 | Supply & fixing in repair brass C P tubular towel rail, 60 cm long, 20mm bore, chromium plated complete all as specified & directed |
| 82 | S & FCI floor trap, plain with grating including jointing with solvent cement (Diameter of outlet 100 mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbed portion complete all as specified and directed. |
| 83 | S & FCI floor trap, plain with grating including jointing with solvent cement (Diameter of outlet 75 mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbed portion complete all as specified and directed. |
| 84 | S&F in repair CP soap dish brass chromium plated, size 100 x 60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed. |
| 85 | S & F in reapir 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed. |
| 86 | S & F110 mm bore PVC (SWR) bends of any radius complete all as specified and directed. |
| 87 | S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm dia bore of pipe complete all as specified and directed. |
| 88 | Removing or dismantling of damage / cracked/ concrete /loose concrete / plaster of celing/ wall/ chajja/ facia to expose the sound and hard concrete using a suitable mechanical device or by hammer and chisels etccomplete all as specified & directed. |
| 89 | M&L for providing and applying on beam, col, ceilings surface by one part alkaline based materialwith corrosion inhibitors (Thermax/Pedilite/Tikitar)and dispersing agents for exposed steel surface after cleaning to loose scale or oxidized chips from bars, having bulk density 1.25. The material to be applied to the rusted metal with brush for complete wetting of rusted metal surface and allowed to react for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel after about 5-7 days, before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth etc to make surface dust free complete all as specified and directed. |
| 90 | M & L for applying bonding agent (Thermax/Pedilite/Fosroc) for bonding old to new concrete surface likes chajja/ beams/ celings/ columns/ faciaetcby high performance modified Styrene- Butadiene Rubber ( SBR ) base binder . Applying ofbinder isas 10 sqm/ per litr ( including necessary arrangements in multy storey bldgs up to height 7 mtr)etccomplete all as specified & directed. |
| 91 | M & L for applying 25 mm thick ( average ) smart care repair mortar (Asian/Thermax) ready to use single component polymer modified repair mortar for repair of RCC members likes beams, columns, chajja , facia , mortar having good compressive strength of not less than M-30 and shrinkage resistance,mixing as per manufacture instruction etc ( including necessary arrangements in multy storey bldgs up to height 7 mtr ) complete all as specified & directed. |
| 92 | S&F galvanised welded steel wire fabric as extra reionforcement to RCCmembers likeceilings, chajja’s, beams, columns parapet walls, waste slab etc including all cutting and waste (wt not exc 4.00 kg/Sqm)complete all as specified and directed. |
| 93 | Preparing old plastered or unplastered surfaces of wallsand applying two coats of oil bound distamper over a coat of average 2mm thick Birla putty incl rubbingcomplete all as specified and directed. |
| 94 | Preparing new plastered or unplastered surfaces of wallsand applying two coats of oil bound distamper over a coat of average 2mm thick wall care putty incl rubbing complete all as specified and directed. |
| 95 | M & L for preparing new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide zinc shromeprimer complete all as specified and directed. |
| 96 | M & L for preparing oldsteel surface and applying one coats of synthetic enamel paintcomplete all as specified and directed. |
| 97 | M & L for preparing oldwooden surface and applying one coats of synthetic enamel paintcomplete all as specified and directed. |
| 98 | M & L hard core of broken stone or boulder having gauge n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed. |
| 99 | M&L for 75 mm thick Cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing surface even and rough using broomfinish complete all as specified and directed. |
| 100 | M&L for60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified & directed. |
| 101 | Dismantling wrought iron or mild steel work of any description not otherwise rovided for complete all as specified & directed. |
| 102 | Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any complete all as specified and directed |
| 103 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed |
| 104 | Supply only GI chain link fencing including line wires to any type of standards, rails, straining bolts, etc. complete all as specified and directed.Note :- (i)Line wire screw bolt and flat iron will be measured and paid separately.(ii) Board of officers shall be conveyed by the accepting office for verification the size and weight of chain link fencing. |
| 105 | Fixing only GI chain link fencing including line wires to any type of standards, rails, straining bolts, etc. including provission of flat iron for securing with post and taking down existing chain link fencing complete all as specified and directed.Note :- Screw bolts and flat iron will be measured and paid separately as S&F. |
| 106 | S&FMild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fittedwith washers and one hexagonal or squarenut exc 5cm but n exc 10cm long and 16 to 20 mm diameter of neck complete all as specified and directed. |
| 107 | S & F in repairangle iron as in post and struts in fencing including embedding in concrete, cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., simillar work confirming to Fe-290 Gde E-165 complete all as specified. |
| 108 | S &F of Mild steel flat iron/ round bars Fe 290 (Gde - E-165)10mm dia and over, cut to length, bent to shape required, including welding with fencing post if required for supporting of chain link fencing complete all as specified and directed. |
| 109 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete and all as specified and removingfrom site. |
| 110 | M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts.grade FRLSH PVC insulated unsheathed cable with proper colour codingdrawn in including PVC concealed conduit not less than 20 mm dia with all accessories andFRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, sunk in cast iron/Pressed steel terminal boxes 60 mm deep & 1.6 mm thick duly painted with aluminum inside and anticorrosive paint out side, including 3 mm thick plastic laminatedsheet for mounting switches, sockets, fan regulators etcconnecting earthand making good to the disturbed surfaceof wall/floor and matching with existing specifications.Connections of cable with MCB\"s or bus bar shall be done through proper size copper/brassthimbles.Note :Conduit shall be fixed on surfaceof roof with necessary saddles where concealing of conduitis not feasible at no extra cost for the following :-(a) One light /fan point controlled by one switch |
| 111 | (b) One 5 pin socket outlet 5 Amps on independent board. |
| 112 | (c)One 5 pin socket outlet5 Amps on same board |
| 113 | All as per item No 110 above but with 4 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated unsheathed cable with FRLSH PVC 4 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board for 15 Amps socket outlet/AC Socket outlet complete all as specified and directed. . |
| 114 | Supply and fixing switch piano flush button single pole one way 5 amps 240 volts with polycarbonate body all as specified and directed. |
| 115 | Supply and fixingSwitch piano flush button single pole one way 15 amps 230 Voltswith polycarbonate body all as specified and directed. |
| 116 | Supply and fixingsocket 5 amps 5 pin flush type, 240 volts. with polycarbonate body complete all as specified and directed.. |
| 117 | Supply and fixing socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body all as specified and directed. |
| 118 | S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd,complete all as specified and directed. |
| 119 | S&F ceiling rose , PVC/polycarbonate,, insulated body surface Bakelite 65mm dia three terminals all as specified and directed. |
| 120 | S&F in repair LED batten Tube Light surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption <20W (4 feet 20W) luminaire lumen >2000 lm, system efficiency of >100 lumens /W, with LED binning as per ANSIBin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 450C, driver efficency>85%, power factor>0.9, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and seafty extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification complete all as specified and directed. |
| 121 | Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection,fixed to pole or wall of building with and including suitableBracket made out of25 mm dia GIlightgrade pipe, 1.00 m long bent to shape by cutting & weldingas required & directed and fixed withtwo Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted withtwo coat of aluminium paint over a coat of red oxide primer, and including connecting the fittingto electric sourcewith & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduitincluding all accessories and fixing arrangements for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified and directed.Note:-The period of defects liability shall be 02 Years from the completion of whole work. |
| 122 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm (copper winding) sweep with, blades, and frame and louvers, complete all as specfied and directed. |
| 123 | S&F sub main wiring with two single core FRLSH PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x6 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 1x6 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in conduit not less than 20mm, complete all as specified and directed by Engineer-in-charge including taking down of existing un serviceable sub main wiring complete all as specified and directed. |
| 124 | Supply & fixing in repair of sheet metal enclosure Vertical TPN DB 4 Way double door, Suitable for Flush Mounting and Surface Mounting, With 160 A Copper Busbar for each phase with 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 DB\"s, With provision for 160 Amp MCCB as incomer and SP/TP MCB\"s as outgoingincl cutting/chasing of wall and make in good to the disturbed surface complete all as specified and as directed. |
| 125 | Supply and fixing in repairMCCB 4 pole, 160 Amps, 50 Hz, Icu=25 KA at 415 volts with thermal magneticalongwith adjustable magnetic protection for current setting Icu=Ics = 100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity standard complete all as specified anddirected. |
| 126 | Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp, complete all as specified and directed. |
| 127 | Supply & fixing in repair sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link all as specified and directed. |
| 128 | Supply and fixing MCB SPN 40 to 63 Amp rating 240V, 10KA \"C\" curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified anddirected. |
| 129 | Supply and fixing MCB SP 1 to 32 Amp rating 240V, 10KA \"C\" curve and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified anddirected. |
| 130 | Supply and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 Sqmm 3.5 Core, Complete all as specified and directed. |
| 131 | Excavating in trenches n exc 1.5m wide and n exc 1.5m deep and getting out in hard/dense soil complete all as specified and directed. |
| 132 | Returning,filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as specified and directed. |
| 133 | Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed. |
| 134 | Supply and laying in High density polyethylene pipes (HDPE) double wall corrugated pipe (6mtr length)and 40 mm inner dia laid in trenches complete all as specified and directed. |
| 135 | M&L for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and rivetedto earth plate by means of nuts, bolts, check nuts & washers, of galvanizediron or steelwith connected to test point and testing on completion including 15mm GI light grade pipe for earth leadprotection from earth point to earth plate, including provnadequate quantity of charcoal dust mixed with35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth platewith 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire meshwith and includingall necessary excavation& earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed.NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
