|
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position, not otherwise specifically provided for, complete all as specified and directed. |
| 2 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed. |
| 3 | Taking down cement plaster of any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water including remaval of derbis upto 5 KM distance, complete all as specified and directed. |
| 4 | M&L for non skid ceramic coloured tiles, 7 to 8mm thick (sqare/ rectanglear), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 5 | M&L for non skid ceramic coloured tiles, 7 to 8mm thick (sqare/ rectanglear), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in skirtings, dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM 1:4, complete all as specified and directed. |
| 6 | M&L for coloured glazed ceramic coloured tiles of size 300x200x7/8mm or 350x250x7/8mm or 450x350x7/8mm as on vertical surfaces of walls, dados, skirtings etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick rendering in CM 1:4 and fair to recive tiles, complete all as specified and directed. |
| 7 | M&L for 10mm thick vitrified light shade coloured ceramic tiles (square/ rectangular), polished, area of each tiles not exceeding 0.36 Sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 8 | M&L for 10mm thick vitrified light shade coloured ceramic tiles (square/ rectangular), polished, area of each tiles not exceeding 0.36 Sqm as in skirtings, dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM 1:4, complete all as specified and directed. |
| 9 | M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding and polishing with rounding to edges of stone slabs one edge complete, fixed over and including10mm thick backing coat in CM 1:4, complete all as specified and directed. |
| 10 | M&L for 10mm thick rendering in CM 1:6 on fair face of brick work or concrete surfaces and finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 11 | M&L for 15mm thick rendering in CM 1:4 on fair face of brick work or concrete surfaces and finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 12 | M&L for 5mm thick rendering in CM 1:3 as on ceilings and finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 13 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. |
| 14 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of primer including 1-2mm thick wall acre putty, complete all as specified and directed. |
| 15 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat of primer, complete all as specified and directed. |
| 16 | Demolition of brick work or stone masonry, built in cement mortar including all quoines, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed. |
| 17 | M&L for brick work with sub class ‘B’, old size bricks, straight or curved on plan exc 6 mtr mean radius, built in CM 1:6, complete all as specified and directed. |
| 18 | M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4, complete all as specified and directed. |
| 19 | S&F in replacement of WC (squatt pattern) including cement concrete bedding, size 580mm x 440mm including PVC\"P\" or \"S\" trap, front and back inlet and with internal foot rests (excluding flushing cistern) including flush pipe and connector pieces of PVC and removed old CI Pipe including demolition of PCC upto 450mm depth, complete all as specified and directed. |
| 20 | S&F in replacement of wash down water closet (pedestal pattern) complete with pedestal pan and \"P\" trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. including PVC seat and cover for pedestal pan and CP Jet alongwith flexible tube/pipe of suitable size, complete all as specified and directed. |
| 21 | S&F in replacement of PVC low level flushing cistern, 10 ltrs capacity, valveless, syphonic action type, white with inlet, ball valve, float and handle including brackets and PVC 32mm dia flushing pipe etc, complete all as specified and directed. |
| 22 | S&F in replacement of wash basin, vitreous china (flat back or angle back type),size 550mm x 400mm including cutting for and pinning in ends of brackets or erecting stand including CP waste coupling of 32mm dia and PVC waste pipe of 32mm bore, complete all as specified and directed. |
| 23 | S&F in replacement of vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe) but including urinal spreader with PVC connection of 15mm dia with PTMT nuts of length 450mm and PVC waste pipe of 32mm bore and CP waste coupling, complete all as specified and directed. |
| 24 | S&F in replacement of PVC connection of 15mm dia with PTMT nuts of length 600mm, complete all as specified and directed. |
| 25 | S&F in replacement of health faucet, CP brass with 8mm dia 1 mtr long flexible tube with wall hook, complete all as specified and directed. |
| 26 | S&F in replacement of CP Jet for EWC with required size of jet pipe (flexible) and connection to 15mm bore iron pipe, complete all as specified and directed. |
| 27 | S&F in replacement of ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 15mm bore iron pipe (minimum weight 142 gms) including fixing of socket if required, complete all as specified and directed. |
| 28 | S&F in replacement of ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 20mm bore iron pipe (minimum weight 210 gms) including fixing of socket if required, complete all as specified and directed. |
| 29 | S&F for 3 layer rotational moulded polyethylene water storage tank, white in colour, 500 ltrs capacity (cylindrical vertical with closed top) including taking down existing water tank and disconnecting old RCC tank etc, hoisted and fixed in position including tank nipple inlet and outlet and conneting pipes, complete all as specified and directed. |
| 30 | S&F for 3 layer rotational moulded polyethylene water storage tank, white in colour, 1000 ltrs capacity (cylindrical vertical with closed top) including taking down existing water tank and disconnecting old RCC tank etc, hoisted and fixed in position including tank nipple inlet and outlet and conneting pipes, complete all as specified and directed. |
| 31 | M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded crshed stone aggregates) as in foundation, filling and mass concrete, complete all as specified and directed. |
| 32 | M&L for colour chequered cement concrete tiles of 30cm x 30cm x 25mm thick each, glossy finish, set, jointed and pointed in neat cement slurry to match the shade of tiles as in floors, fixed over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 33 | M&L for machine pressed rubber moulded manufactured/ compacted by vibrating table method precast concrete interlocking paver block, Laquor finish, any shape and size, confirming to IS:15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment and joints filled with sand, laid over and including 25mm thick sand, complete all as specified and directed. |
| 34 | Taking up or down steel tubing and connection including cleaning for re-fixing or removal to store, size of pipe 15mm bore, complete all as specified and directed. |
| 35 | Taking up or down steel tubing and connection including cleaning for re-fixing or removal to store, size of pipe 20mm bore, complete all as specified and directed. |
| 36 | M&L for 15mm bore medium grade galvanised tube with all fittings and fixed to walls (concealed type) and ceiling or laid in floors, complete all as specified and directed. |
| 37 | M&L for 20mm bore medium grade galvanised tube with all fittings and fixed to walls (concealed type) and ceiling or laid in floors, complete all as specified and directed. |
| 38 | S&F in replacement bib tap, long body, chroimum plated (ISI Marked with valid CML No) with crutch or butterfly handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule including elbow/socket as required at site, complete all as specified and directed. |
| 39 | S&F CP shower with arm 15mm size 195mm long with bend of 45 degree with flange including taking down the existing UNSV shower of any type/shape, complete all as specified and directed. |
| 40 | S&F in replacement of angle valve, brass, chromium plated, fancy type,with capstan head handle, screwed down high pressure including CP brass wall flanges, screwed for 15mm bore pipe connection, complete all as specified and directed. |
| 41 | S&F in replacement of two way angle cock, long shank, chromium plated, brass, fancy type, screwed down high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions including fittings as required at site, complete all as specified and directed. |
| 42 | S&F in replacement of pillar tap, cast copper alloy with capstan heads handle, chromium plated, fancy type, screwed down high pressure with or without lettered \"Hot\" or \"cold\" with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe connection, complete all as specified and directed. |
| 43 | S&F in replacement of plastic water closet seat cover, white, closed pattern with flat bottom with mild steel chromium plated or aluminised hinging device, complete all as specified and directed. |
| 44 | S&F in replacement of looking mirror of size 600mm x 450mm, plain edge 5mm thick selected quality glass, mounted on 6mm thick commercial plywood with frame and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 45 | Taking down chowkats or frames with shutters (without taking off shutters from the frame), area not exc 1.50 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed. |
| 46 | Taking down chowkats or frames with shutters (without taking off shutters from the frame), area exc 1.50 Sqm but not exc 4.00 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed. |
| 47 | Taking down shutters of any description, area not exc 1.0each, complete all as specified and directed. |
| 48 | Taking down shutters of any description, area exc 1.0 Sqm but not exc 2.0 Sqm each, complete all as specified and directed. |
| 49 | S&F pressed steel frames, size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate and cement concrete 1:2:4type B-0 (using 12.5mm graded crushed stone aggregates) as filling inside hollow section etc, complete all as specified and directed. |
| 50 | S&F 35mm thick 2nd class hard wood glazed and skeleton factory made shutters (three panel), open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters, complete all as specified and directed. |
| 51 | S&F plain framed panelled shutter 35mm thick 2nd class hard wood (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 52 | S&F flush shutters, 35 mm thick solid core construction with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 53 | S&F solid PVC door frame of size 50mm x 47mm, made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube in opening as per site, complete all as specified and directed. |
| 54 | S&F solid panel PVC door shutter 30mm thick (style), consisting of frame made out of MS tubes for top and bottom rail, MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as specified and directed. |
| 55 | S&F in repair 18mm thick prelaminated medium density fibre boards, glossy finish/ UV finish interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screw hinges or piano type (continues hinges) and welding as in cup boards, shelves, kitchen cabinet etc, complete all as specified and directed. |
| 56 | S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 57 | S&F 3mm thick plain glass, ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane including hacking out old broken glass of any size, type and thickness, complete all as specified and directed. |
| 58 | S&F 150mm long aluminium, anodised barrel tower bolts of extruded section and fixed with SS screws, complete all as specified and directed. |
| 59 | S&F 150mm long aluminium handle, cast type, anodised and fixed with SS screws, complete all as specified and directed. |
| 60 | S&F 100mm long steel butt hinges, heavy weight, cold rolled and fixed with SS screws, complete all as specified and directed. |
| 61 | S&F 250mm long aluminium alloy, anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed with SS screws, complete all as specified and directed. |
| 62 | S&F continues (piano) type hinges, heavy weight, cold rolled and fixed with SS screws, size 30mm wide when opened, complete all as specified and directed. |
| 63 | S&F floor door stoper of 140mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed with SS screws, complete all as specified and directed. |
| 64 | S&F in replacement of 300mm size ordinary rat tail, rod pattern springs including roller and roller plate, fixed to wooden or steel frames with welding etc, fixed with SS screws, complete all as specified and directed. |
| 65 | M&L for welding of small mild steel articles such as butt hinges of any size, pintel hinges of any size, steel window frames, MS door chowkats all upto height of G+6 building including necessary parts and fixing the same to existing frame, required as per site including necessary scoffolding ladder etc, complete all as specified and directed.Note :- Rates for necessary scaffolding ladder shall be deemed to include in the quoted rates. |
| 66 | S&F 32mm dia PVC wate pipe of 900mm long and fixed in position, complete all as specified and directed. |
| 67 | S&F brass spindle of any size, suitable for bib tap, pillar tap, angle cock, all type of mixture, complete all as specified and directed. |
| 68 | S&F in replacement of PVC flushing cistern kit of any type and fixed in position, complete all as specified and directed. |
| 69 | M&L for factory made (box type) mild steel widow / ventilators glazed and gauged combined shutter with side hung including box type hinges, steel peg stay, locking arrangement with glazing and gazing bar, dovetailed or welded with one shop coat of red oxide primer, complete all as specified and directed.Note :- (i) The window / ventilator shall be fabricated as per drg No. CEUZ/TD/1302/2009 Sheet 1/3 to 3/3.(ii) MS fillets, glazing, wire gauges shall be measured and paid for seperately under respective items.(iii) One side out to out dimensions shall be measured for payment of combined window (glazed & gauged). |
| 70 | M&L for preparation of new or previously untreated steel surface of any description, exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 71 | M&L for preparation of new wooden or untreated wood surfaces of any description, exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 72 | S&F in replacement of sink with drainage board, made of stainless steel 1mm thick sheet kitchen or laboratory with plugs, washers and wastes including waste coupling and waste pipe & bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed. |
| 73 | Dismantling of timber scantling of any size and shape framed work 40 Sqcm and over in section, complete all as specified and directed. |
| 74 | Dismantling of asbestos cement (corrugated or semi corrugated etc.) sheets in roof covering including ridges, complete all as specified and directed. |
| 75 | S&F of 6mm thick asbestos cement corrugated or semi-corrugated sheets as in roofs, walls etc. fixed with \"L\" or \"J\" type hooks, complete all as specified and directed. |
| 76 | M&L for mild steel work for tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes, conforming to IS:1161-1979 Grade ST-240, complete all as specified and directed. |
| 77 | S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls / ridges, fixed with self tapping screws, complete all as specified and directed. |
| 78 | S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls, fixed with self tapping screws, complete all as specified and directed. |
| 79 | S&F centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy with dual capstan heads, chromium plated, screwed down high pressure with lettered \"Hot\" & \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and directed. |
| 80 | S&F single lever wall mixer, brass, chromium plated, fancy type with capstan head handles with lettered \"hot\" and \"cold\", screwed down high pressure including CP brass wall flanges and necessary extension nipples, screwed for 15mm bore pipe connection, complete all as specified and directed. |
| 81 | Taking down eaves gutters and rainwater pipes upto 7 storey Bldg (23 Mtr height) of any size or pattern including all fittings, heads, shoes, bends swan necks etc. including necessary arragement for fixing of pipe like scaffolding, ladder and all other fittings /accessories, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 82 | S&F PVC (SWR) pipes of bore 100/110mm, single socketed in any length with rubber ring joints, fixed to walls/ floor with stack clamps and fixed with nuts and bolts upto 7 storey Bldg (22 Mtr height) including neceassary scaffolding, ladder and necessary arragement for fixing of pipe, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 83 | Fixing only PVC (SWR) pipes of bore 100/110mm, single socketed in any length with rubber ring joints, fixed to walls/ floor with and including stack clamps and fixed with nuts and bolts upto 07 storey Bldg (22 Mtr Height) including neceassary scafolding, ladder and necessary arragement for fixing of pipe, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 84 | S&F PVC (SWR) bends with access door of any radius, suitable for 100/110mm bore pipe, fixed upto 07 storey bldg including neceassary scaffolding and other arragement, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 85 | S&F PVC (SWR) branch piece, single (single Y/T) equal or unequal, suitable for 110mm bore pipes, fixed upto 07 storey bldg including neceassary scafolding and other arragement, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 86 | S&F PVC (SWR) pipes of bore 75mm, single socketed in any length with rubber ring joints, fixed to walls/ floor with stack clamps and fixed with nuts and bolts, complete all as specified and directed. |
| 87 | S&F PVC (SWR) bends with access door any radius, suitable for 75mm bore pipe, complete all as specified and directed. |
| 88 | S&F PVC (SWR) branch piece, single (single Y/T) equal or unequal, suitable for 75mm bore pipe, complete all as specified and directed. |
| 89 | S&F 100mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in trenches or in floors, complete all as specified and directed. |
| 90 | S&F 75mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints, laid in floors or fixed to walls with MS clamps of suitable size, complete all as specified and directed. |
| 91 | S&F in replacement of 100mm bore sand CI bends/ reducer/ Tee (any radius) with access door diminishing pieces or tapers (larger bore measured), complete all as specified and directed. |
| 92 | S&F in replacement of 75mm bore sand CI bends/ reducer/ Tee (any radius) with access door diminishing pieces or tapers (larger bore measured), complete all as specified and directed. |
| 93 | S&F 100mm bore CI vent cowl including taking down old CI vent cowl of any type, complete all as specified and directed. |
| 94 | S&F 75mm bore CI vent cowl including taking down old CI vent cowl of any type, complete all as specified and directed. |
| 95 | S&F 75mm dia PVC (SWR) multi floor trap with grating including jointing with solvent cement, complete all as specified and directed. |
| 96 | S&F false ceiling with everest fiber cement designer tile lvory/ white painted (high pressure steam cured) of 4mm thickness (as per IS:14862) of size 595x595mm and any one of the design (occeanic, lake & hill cascade or electra) in true horizontal level, suspended on interlocking power coated certa black pattern metal grid of hot dipped galvanised steel section (galvanised @ 12gms both side inclusive) consisting of main \"T\" runner with suitably spaced joint to get required length and 15x32mm made of 0.30mm sheet spaced between main \"T\" @ 600mm C/C from a ridge of 600x600mm and wall angle of size 15x20mm made of 0.30mm thick sheet and laying false ceiling tile in the grid including required cuttig / making opening for service like diffuser grils light suspended from ciling using GI soffit cleats fixed to existing rafters purlin etc with dash fastener GI adjustable rod of 3mm dia with galvanised butterfly level clips spaced at 1200mm c/c along main T bottom exposed width of 15mm of all \"T\" sections shall be centre black prepainted with polyester paint and having a load bearing capicity of 12 Kg/Sqm and refixed all existing electric wiring and fixture all complete all heights and as directed by Engineer-in-Charge. |
| 97 | S&F PVC wall lining, consisting of 5mm thick wood grain PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed. |
| 98 | S&F mortice lock with two lever mild steel body (vertical type), 100mm length of latch with 3 set of keys, fixed in door shutter with proper in position, complete all as specified and directed. |
| 99 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions(Fixed portions) with extruded built up standard tubular sections/appropriate Z sections sliding /openable 02 or 3 tier and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 100 | M&L for powder coated anodised aluminium door shutter, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, handles 2 Nos in each door, hingesanodised aluminium snap beading, screws etc, complete all as specified and directed. |
| 101 | M&L for powder coated anodised aluminium sliding shutter of window andventilator openable/ louvers, fixed/ sliding type shutters without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos), suitable handle (1 No), complete all as specified and directed. |
| 102 | S&F powder coated anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/ pattern with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. |
| 103 | S&F anodised aluminium (minimum thickness of powder coating 50 micron) framework for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate \"Z\" sections sliding /openable, 2 or 3 tier and other sections of approved make, conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws, complete as per architectural drawings and the direction of Engineer-in-Charge. |
| 104 | M&L for anodised aluminium door shutter, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, handles 2 Nos in each door, hingesanodis etc, aluminium snap beading, screws etc, complete all as specified and directed. |
| 105 | M&L for anodised aluminium sliding shutter of window and ventilator openable/ louvers, fixed/ sliding type shutters without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos), suitable handle (1 No), complete all as specified and directed. |
| 106 | M&L for anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screws @ 200mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. |
| 107 | S&F 5mm thick tinted/ plain glass sheet, fixed to aluminium section of doors, windows and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame, complete all as specified and directed. |
| 108 | S&F in replacement of door closers of aluminium die cast body hydraulically regulated designation No 3, universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 KG, complete all as specified and directed. |
| 109 | S&F mild steel peg set of 6 with PVC coating, fixed in the MS hooks, any size, shape and description and fixing in wooden, PVC or conctere surface, complete all as specified and directed. |
| 110 | M&L for mild steel 20mm dia curtain rod with PVC coating, fixed in the MS hooks, and finials/ side brackets (both side), shade as approved, complete all as specified and directed. |
| 111 | M&L for preparation of plastered or unplastered old surfaces of ceiling by moulds, moss, efflorscent salt, trading oil and greasy spots etc. and applying one coat of white wash, complete all as specified and directed. |
| 112 | M&L for preparation of old distempered surfaces of walls, plastered or unplastered by washing, rubbing down and stoping of distempered and painted surfaces and applying one coat of oil bound distempered, complete all as specified and directed. |
| 113 | Complete removal of existing treatment of old decorated surfaces of walls, plastered or unplastered by washing, rubbing down and stopping of distempred and painted surfaces and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed. |
| 114 | M&L for preparing of old surfaces of walls and applying one coat ofbirla white putty and finished smooth, complete all as specified and directed. |
| 115 | M&L for preparation of plastered or unplastered old surfaces of walls, chajja, balcony, facia etc. by brooming down or steel wire brushing, scraping down smoke soots, moulds, moss efforescent salls, treating oil and greasy spots etc. and applying one coat of cement base paint in any pattern upto 07 storey bldg (Appx 23 Mtr height) including necessary arragement like scaffolding, ladder etc, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 116 | M&L for preparation of plastered or unplastered old surfaces of walls, chajja, balcony, facia etc. by brooming down or steel wire brushing, scraping down smoke soots, moulds, moss efforescent salls, treating oil and greasy spots etc. and applying two one coat of cement base paint in any pattern upto 07 storey bldg (Appx 23 Mtr height) including necessary arragement like scaffolding, ladder etc, complete all as specified and directed.Note :- Rates for necessary scaffolding, ladder or other means shall be deemed to include in the quoted rates. |
| 117 | Checking of joinery such as wooden/ steel / aluminium/ iron mongery/ pelmet box ,door spring etc. requiring carpenter work and carring out minor repair such as tighting of screw / nails, minor adjustement, cutting of chease of joinery, door/ window by means of palner / chiesling etc. including petty reapir material like screws, nails, plugs etc. to make it functional, complete all as specified and directed.Notes :- (i) Any item required to be replaced shall be paid under respective items of this BOQ and in that case this item shal not be measured and paid. (ii) The contractor or his authoried rep shall collect the complanit of all carpenter work from complaint cell/ JE-in-charge daily and all complaint shall be rectified by the contractor within the same day then the return complaint slip after completion of complaint and get recieved from concern JE. |
| 118 | M&L for attending the water leakage from bib tap, flushing cistern, pillar tap, wash hand basin, mixer, GI pipe line and othe required pluming work such as replacement of washer, GI nipple, GI socket and any other GI fittings, check nuts, tightining nuts etc. including petty material like washer of all size, tread, M seal, screws and to make the same fully functional and leak proof, complete all as specified and directed.Notes :- (i) The rates shall be included for one Plumber (skilled) and one Helper (semi skilled) for attending the daily complaint. (ii) Necessary recovery shall be made in case of complaint should not done in the same day @ Rs. 150 per complaint per day.(iii) Any item required to be replaced shall be paid under respective item and in that case this item shall not be measured and paid.(iv) The contractor or his authoried rep shall collect the complanit of all carpenter work from complaint cell/ JE-in-charge daily and all complaint shall be rectified by the contractor with in the same day then the return complaint slip afeter completion of complaint and get recieved from concern JE. |
| 119 | S&F in repair rigid non - metalic PVC casing caping of 25/12mm inclusive of all elbow, tees,etc complete all as per the direction of Engr-in-Charge. |
