|
| 1 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift up to 1.5 m.(a)All kinds of soil |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(a)All kinds of soil. |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a)1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size) |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinthlevel : (a)1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 8 | Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat andpressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. hollow tube frame or as decided by Engineer-in-Charge (Payment of M.S. frame shall be paid separetely). Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. |
| 9 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates efc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 10 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mmthick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.(a) 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 11 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved |
| 12 | Schedule-BProviding and fixing of MULTI ACTIVITY PLAYSYSTEMof Make ARIHANT/KOMPAN/LANDSCAPE STRUCTURES/OK PLAY/ LEO/ KAALIAwith consist of various activity like Roller slide, Wave slide, Spiral Slide, Net Clamber, Spiral Climber, Bridge Connector/Tunnel, Bubble panels, along with brail panels for blind childrens. The structure of complete MAPS made with B-class GI Pipes with powder coating process of 60-80 Microns. a) 3 Nos. Hex Deck with Canopy: The platform shall be made of Fiber Reinforced Plastic with anti-skid surface. The platform will be powder coated. The platform should be of regular Hexagonal shape. The top canopy shall be made of Fiber Reinforced Plastic with a minimum thickness of 2-3 mm. Canopy is assembled from six modules and at the top of its dome is fixed. b) FRP Ladder: The ladder shall be made up of Fiber Reinforced Plastic with a conservative thickness of 4 mm. Ladder should have reinforcement to maintain strength and avoid bending. The top surface of the ladder should be such that it should not deserve any kind of kiddy movement. c) FRP Roller Slide: In the roller slide the rollers are made up of HDPE with UV stabilized pigments of 2.5 mm thickness provided with Nylon bush and are mounted on 12 mm Dia. rod and fix in slide chute. The frame of the slide is made from 50x50x5mm M.S. angle and handrail is 25 mm NB GI pipes. The landing support is made from 25 mm NB pipes. d) Spiral Slide: Spiral slide chute is made of fiber reinforced plastic having shell thickness of 4 mm.The back side of the slides is at surface matel with platform effect slide is supported on 80 mm NB center GI pipe. Landing module is supported by 20 mm NB pipe. Railing is made up of LLDPE in roto mould process. It is support by 20 mm NB GI pipes. The support pipe is powder coated to avoid rusting of the pipe. e) Roto Railing: Railing is provided for all the decks for safety purpose. It is made up to low-density polyethylene plastic in rotational mould process and has a support of 20 mm NB powder coated GI pipes. The railing is attached to the support pipe using a nylon clamp. f) Spiral Climber: It is fabricated out of 25 mm NB GI pipes. The spiral structure is suitably bent and is kept standing with vertical 40 mm NB GI pipe support.g) Rope Net Climber: It is made out with powder coated 20 mm O.D. and 25 mm O.D. G.I. Pipe Frame having nylon clamps in PP Rope.h) Bridge Connector/Tunnel: It is made out 5mm thick FRP sheet in appropriate shape & color having connecting arrangement at both ends.i) Tactile Panel: Tactile panels to be provided at site of MAPS for the blind children.j) Bubble panel: Colorful bubble panel provided around the MAPS for the more fun.k) Wave slide 1.5 Mtr. : This FRP wave slide consists of ISI marked structure. The attractive FRP wave slide chute is made up of 4 mm thick fiber reinforced plastic. The structure is made up of 20 mm NB and 25 mm NB powder coated GI pipes. The slide is supported on 80 NB powder coated GI pipes. The ladder cum railing is made 20 mm NB and 25 mm NB GI pipes respectively. The platform of the slide is made up of 16 SWG GI sheet with anti-skid for firm foot grip. There are triangular steps 16 SWG GI sheet. The slide chute has its end such as it causes safe landing of the child. The play area of complete MAPS is 10 Mtr. x 7.5 Mtr. Appox. and required safe play area 12x9.5 Mtr. Appox. The manufacturing of play equipment as per the All international standards (ASTM/ F1487/ F1292/F2223/ BS/EN/1176) including maintenance cost for 1st year. |
| 13 | Providing & Fixing of WHEEL CHAIR SWING for physical disable person of the arc shaped powder coated mainframe of B-Class GI Pipe connected with swinging clamps, Rubber coated chain and specially design handicap swinging seat along with height adjustment feature & supporting clamps hooks etc. A suitable GI platformto be provided at bottom side of swing for easy movement of disable person to use the play equipment at site.The play area of complete Wheel Chair Swing is 2.0 Mtr. x 3.0 Mtr. Appox. and required safe play area 5x5.5 Mtr. Appox. The manufacturing of play equipment as per the All international standards (ASTM/ F1487/ F1292/F2223/ BS/EN/1176)including maintenance cost for 1st year. |
| 14 | Providing and fixing of TODDLER SWING of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/OK PLAY/ LEO/ KAALIA.In the toddler swing the center support is made up of 80 mm NB GI pipes. The horizontal bars are made up of 50 mm NB powder coated GI pipes. The bucket seats of the toddler swing are made of rubber with anti-skid. The ball bearings are mounted inside specially designed nylon balls. The rubber seat is affixed on 6 mm thick GI chain. The seats are made with full care so that the child does not fall from it while swinging. All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelines including maintenance cost for 1st year. |
| 15 | Providing and fixing of MULTI SEATER SEE SAW of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/OK PLAY/ LEO/ KAALIA. The Multi Seater See saw comprises four Rotational seats. The lever consists of 20 mm NB and 80 mm NB powder coated GI pipes. The bearing used in this product is heavy duty nylon bush type. The stand for see saw is made using 50 mm NB GI pipe.All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelinesincluding maintenance cost for 1st year. |
| 16 | Providing and fixing of Double Arch swing of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/OK PLAY/ LEO/ KAALIA.The arch shaped side frame of the double arch swing is made up of 80 mm NB GI pipe and top pipe is made up of 50 mm NB GI pipe. The frame is powder coated to give an esthetic look. Seats- Belt Type seats made of Synthetic Rubberised material/Fiber reinforced fabric materials of Virgin Reinforced material. The belt seat is suspended on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clamp.All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelines including maintenance cost for 1st year. |
| 17 | Providing & fixing of SPRING RIDER BIKE (RACER) of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/ OK PLAY/ LEO/ KAALIA. The typical Spring Rider is comprises of Flexible Spring & HDPE sheets of high quality. It’s specially made for kids in between 3 to 8 yrs. It’s designed specially keeping in mind growing kid’s mental development aspects & safety aspects. Playing on this spring rider will enable the kids to develop coordination between force & balance which is required for proper mental development. It also enhances griping power of children which will in turn strengthen growing bones. The rest is only fun that’s required for emotional development of a children. All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelinesincluding maintenance cost for 1st year. |
| 18 | Providing & fixing of SPRING RIDER DUCK of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/ OK PLAY/ LEO/ KAALIA. The spring rider being a whale/pony or bike rider provides an unlimited fun to the children riding on it. The whale/pony or bike is made out from fiber reinforced plastic (FRP). The handles of duck & pony provided for gripping is made up of 15 mm NB GI pipes, whereas the duck is made out of LLDPE in rotational molding. The duck is mounted on a pair of heavy-duty compression spring. Also a GI flat is provided for footrest. The spring is mounted on 5mm thick plate. And the stand for support is made out of 40 mm NB pipe. All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelinesincluding maintenance cost for 1st year. |
| 19 | Providing & fixing of LOOP RUNG SCRAMBLER of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/ OK PLAY/ LEO/ KAALIA. This loop rung provides hanging experience to the children. The frame is fabricated out of 40mm NB and 25mm NB powder coated GI pipes. There are nine triangular loops made from 15 mm NB, which are welded to the top pipe of the frame. The top pipe is made out of 80 mm NB GI pipes. The ladder used is designed to the side support pipe itself. All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelinesincluding maintenance cost for 1st year. |
| 20 | Providing & fixing of MINI SLIDE of make ARIHANT/KOMPAN/LANDSCAPE STRUCTURE/ OK PLAY/ KAALIA. The center support of the Mini Slide is made up of 50 mm NB GI pipe. The slide is made from Fiberglass reinforced plastic (FRP). The thickness of the mini slide is 3-4 mm with proper reinforcement to support the module. The triangular steps of 16 SWG are provided and the ladder frame is made in 20 mm NB and 25 mm NB powder coated GI pipe. The landing support is made up of 25 mm NB GI pipes. The ladder is designed in such a way there won’t entrap child’s foot while playing. The pure polyester powder coating done on the pipes extends the life of equipment. All completeas per the direction of engineer in charge or as per approved drawing & design given by manufacturerincluding earth work, c:c workup to plinth level, c:c block1:2:4(1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size)of required size as per department / manufacturers specifications and guidelinesincluding maintenance cost for 1st year. |
| 21 | Deduct for taking away Mild steel dismantle material. |
| 22 | SCHEDULE-\"C\" Maintenance charges for children Play equipments 9 Nos.(S.No. 12 to 20).a) For 2nd year |
| 23 | b) 3rd year |
| 24 | Modified estimate cost after using correction factor on DSR 2023 on Account of GST @ 0.973 on Item no. 1-11 (614760.00*0.973= 5,98,161.00) |
| 25 | CONDITION :-1. Completion certificate shall be recorded after completion of Schedule ‘A’ & \"B\" and a supplementary agreement shall be executed for Schedule ‘C’ for maintenance work.2. The equipment is to be maintained for 3 years by the agency. First year maintenance is included in the rate and 2nd year onwards, Maintenance charges shall be paid as per rated mentioned in schedule ‘C’ after satisfactory completion of 2nd year and 3rd year. An amount equal to 10% of the cost of children play equipment shall be withheld from R/A bills, which shall be released after completion of maintenance period. 3. For non-maintenance of equipment a penalty ofRs. 1000/- per fortnight per park for 9 nos. equipmentsshall be recovered from the agency .4. Maintenance of equipment’s includes replacement of nut bolts, damaged parts , oiling and greasing, bearing, shafts etc. An inspection after 15 days shall be carried out by the agency.5. An additional security equal to 10% cost of children play equipments shall be withheld from R/A bills, which shall be released after maintenance period of three years, which can be released on submission of FDR or bank guarantee in the account of Sr.AO/CAU/HZ. |
