|
| 1 | Design, supply, testing and commissioning of architectural surface spot light in the range of 1800K to 2200K LED luminaire. The luminarie housing material of Pressure Die- Cast Al. construction with special anti-glare baffles ensuring high impact resistance & resistant to water, moisture. The housing shall have Black, White, Grey finish based on site requirement. The system nominal wattage shall be not less than 15W at full load and system lumen output of not less than 1200 lumens. Fixture shall be available with high power LED and architectural optics with choice of beam angles of Mid 24°. The fixture operating temperatue shall be 0⁰C - 45⁰C, and the power factor should be >0.95. Fixture dimension shall be not larger than 110 x 80 x 180 mm. Fixture shall have auto-ranging operating voltage for 140 – 270 VAC and the THD shall be <5%. Fixture shall equipped with IP65 and Imechanical impact of minimum IK08. The driver should have HV Cut off @320V/440V Protection for 8 Hrs, low voltage cut-ff and Open & short circuit Protection. The bidder should submit the BIS with valid R code. (The rates are inclusive of three years maintenance for LED luminaries including replacement ) |
| 2 | Design, supply, testing and commissioning of compact DMX signal splitter that takes the incoming DMX512/RDM signal and amplify the signal and supporting bi-directional communications for discovery, addressing and DMX control of light fixtures.This unit takes the incoming DMX/RDM signal and splits the signal into six separate output channels allowing for expanding the number of devices controlled from 32 to 6 X 32. The output terminals are electronically isolated from the input & RDM-through port and share a common ground reference. All six output ports have an independent output driver to boost the DMX/RDM signal. Operating temperature shall be -10° to 35°C. The maximum power consumption shall be less than 4.5W and input voltage shall be 12-24V DC. (The rates are inclusive of three years maintenance for LED luminaries including replacement |
| 3 | Design, supply, testing and commissioning of controller to author, configure, and control dynamic LED light shows for DMX lighting networks. The controller with two universe of DMX ports control up to 340 light addresses, Works as a stand-alone or computer-driven controller, Secure Digital (SD) card drive for flexible show storage , USB 2.0 interface for downloading shows and configuring from attached PC or Mac, Simple installation and wiring is required, Flexible, adaptable mounting options are expected, Should be provided with light show authoring software, Direct line voltage power supports 100 — 240 VAC , Six configurable effects — Using light show authoring software to select from six effects, adjust effect settings, such as color, speed, and brightness etc as required.(The rates are inclusive of three years maintenance for LED luminaries including replacement |
| 4 | Design, supply, testing and commissioning of compact surface mounted type DMX AC Decoder. The product shall be Standard DMX512 compliant control interface, enable to set the DMX address freely. And show address Via digital numeric display. It can capable to handle max 5A output.The device work stand-alone manual on/off mode selectable, which be controlled by buttons, instead of DMX signal. Input voltage shall be 100-240V AC and support upto 5A with with capacitive or inductive load and upto 15A with resistive load output current and 500-1200W. The product operating temperature shall be -30 to +55 deg. Fixture shall equipped with IP20 and it should comply EN IEC 55015:2019+A11: 2020, EN 61547:2009, EN IEC 61000-3-2:2019+A11:2021 and EN 61000-3-3: 2013+A11:2019. (The rates are inclusive of three years maintenance for LED luminaries including replacement) |
| 5 | Supply and fixing of Standalone Asymmetric linear Warm White LED luminaire made of extruded aluminimum with Black Powder Coated finish, With Lenses and UGR reflector, with reflector color Gun-metal/black. UGR<16 The luminaire having Multiple Lumen Output Options Varying from 3600lm,with system efficacy of ≥80lm/w & system wattage option 45W (±5%) .Assymmetric Optics with the luminaire shall have a width of not more than 45mm, height 80mm and 2150mm lengths. The life shall be 50K Hrs. at L70B50. Operating temperature of the luminaire shall be 0°C to +45°C and driver shall comply to the minimum electronic paramtere like THD≤ 10%, PF ≥0.9, internal surge protection of 4KV, operating voltage range of 140V - 270V having Class - I protection & serviceability of Class B. The luminaire shall be IP20 & IK02 compliance.The driver shall be of the same make as that of LED luminaire and must be EMI/EMC compliant. The LEDs used shall have CCT of 3000K with CRI≥80, & SDCM≤5. The bidder should submit the BIS with valid R code. (The rates are inclusive of three years maintenance for LED luminaries including replacement ) |
| 6 | Design, supply and fixing with suitable supports and necessary bolts and nuts along with suitable MS mesh channel as belowSupply of compact size linear exterior rated architectural and landscape grazing light with 2700K LED luminaire. The luminarie housing material of extruded aluminum with die-cast aluminum end caps, electrostatically applied polyester powder coating finish, system wattage shall be less than or equal to 24W at full load and system lumen output of not less than 1600 lumens and intensity not less than 4,600cd, and it shall have minimum 24 high power LED\"s. Fixture shall be available with high power LED and architectural optics with choice of beam angles of mid 30° x 30°.The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and Clear tempered glass cover for better illumination. Fixture dimension shall be not larger than 1000 x 40 x 90 mm with bracket and weight not more than 1.6kgs. Luminaire should have IP67 male/female connectors for through power + signal connection. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture operating input voltage shall be 24V DC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 2 pole flat cable L=15cm, 2x1.5mm2 with connectors. (The rates are inclusive of three years maintenance for LED luminaries including replacement |
| 7 | Design, supply and fixing with suitable supports and necessary bolts and nuts along with suitable MS mesh channel as belowSupply of compact size linear exterior rated architectural and landscape grazing light with 2700K LED luminaire. The luminarie housing material of extruded aluminum with die-cast aluminum end caps, electrostatically applied polyester powder coating finish, system wattage shall be less than or equal to 36W at full load and system lumen output of not less than 2300 lumens and intensity not less than 7,600cd, and it shall have minimum 36 high power LED\"s. Fixture shall be available with high power LED and architectural optics with choice of beam angles of 15°- 20°x 35°-40° elptical beam.The luminaries shall be with Anti-aging and anti-UV high optical efficiency PMMA lens and Clear tempered glass cover for better illumination. Fixture dimension shall be not larger than 1000 x 40 x 90 mm with bracket and weight not more than 1.6kgs. Luminaire should have IP67 male/female connectors for through power + signal connection. Fixture shall operate in a temperature range of -40°C to 50°C. Fixture operating input voltage shall be 24V DC. Lifetime should be at least 50,000 burning hours at L70 at 35 degree centigrade with total IP66 protection. Fixture shall equipped with mechanical impact of minimum IK06. The luminarie shall have 2 pole flat cable L=15cm, 2x1.5mm2 with connectors. (The rates are inclusive of three years maintenance for LED luminaries including replacement |
| 8 | Supply and fixing of outdoor IP66 rated 24V/ 150W driver or SMPS to provide the supply to the DC luminaries ELG-150-24. (The rates are inclusive of three years maintenance for LED drivers and accessories including replacement |
| 9 | Supply and fixing of outdoor IP66 rated 24V/ 300W driver or SMPS to provide the supply to the above DC luminaries ELG-300-24 (The rates are inclusive of three years maintenance for LED drivers and accessories including replacement ) |
| 10 | Design, supply, testing and commissioning of Supply of 10 pieces of 2mtr factory made 2P /4P/ 5Pmale to female cable to connect the DMX enabled data line for better connectivity (The rates are inclusive of three years maintenance for LED, drivers and accessories including replacement ) |
| 11 | supply and run of 3 core 2.5 sq.mm PVC sheathed copper cable from Junction box to LED fixtures |
| 12 | Supply and Installation of 1 KVA single phase UPS 2 hours backup with connection |
| 13 | Supply and Installation of 4U rack for controller unit |
| 14 | supply and Installation of 15 KVA Three phase Microprocessor controlled Air cooled unbalanced Electronic servo voltage stablizer with High/Low voltage cut off and single phase preventer with Builtin manual bypass arrangments |
| 15 | Supply and run of 75mm x 50mm ,1.6mm thick MS cable mangement Tray with cover , Tees, joint plate arrangements complete with Painting by one coat of red oxide and two coats of painting of suitable colour on the Existing Angle frame work on Stone pillar/wall |
| 16 | Supply and fixing of 1 1/2\"X 1 1/2\"X1/4\" MS angle with 12mm threated rod with suitable Nuts and washer to hold the MS angle on Existing pillar/Wall |
| 17 | Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (Metal) with 1 no.100A 4P MCB switch as incmoing and 12 nos. 6A to 32A SP MCB as outgoing on suitable Angle iron pedestal( floor/wall mounted as directed by the site engineer) with earth connection only |
| 18 | supply and Installation of IP67-TS waterproof threaded-seal connector, dust-tight and protected against temporary immersion (up to 1 m for 30 min) as per IEC 60529, suitable for outdoor electrical connections, rated minimum 240 V, 10 A, UV-resistant housing with silicone sealing |
| 19 | Supply and run of 3 core 1.5 sq.mm PVC flexible copper cable from driver to LED fixtures |
| 20 | supply and run of HDPE pipe of size 50mm/38mm with suitable clamp on existing tray /wall/ ground |
| 21 | Supply and fixing of IP 65 outdoor SMC Box with AI frame support for housing the LED drivers |
| 22 | Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB as incoming and 10 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. |
| 23 | Supply , Erection Testing and commissioning of 415V/50 HZ 200A Cubicle Panel board with centre switches Chamber the bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1”x 1/4 ” copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1”x 1/8” copper flat on either side of the panel board for earth buses , 3 nos. LED pilot lamps set withfuse base, top & 10A HRC Fuse link for 3 phases on a separate Chamber and with the following switches complete.Incoming200A TPN switch disconnector fuse interior only with HRC fuses double break -1no.Outgoing 63A TPN switch disconnector fuse interior only with HRC fuses double break -4nos.Main Panel in Mandapam-1 no. |
| 24 | Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG alu.cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good |
| 25 | Supply and clamping of 3 1/2 x 120 sq.mm. PVC armoured LTUG alu. Cable on wall/ on post with suitable MS clamps |
| 26 | Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection |
| 27 | Supply and providing cable end termination of 3-1/2x120s q.mm. PVCLTUGaluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete |
| 28 | Supply and clarnping of 4 x 10 sq.mm. PVC armoured Copper LTUG cable on post or on wall with MS clamps |
| 29 | Supply and installation of 17.2mm dia 2 mtr. Low carbon steel earth electrode bonded with 250 microns copper with GI clampto be installed in a suitable bore and filled with 50 lbs of cabon bond environment friently back filling compound . An RCC troughed of size 300 x 300 mm should be with RCC cover for protecting the electrode |
| 30 | Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection |
| 31 | Supply and installation of 4MP IP Bullet /Dome camera with key features of not less than 2.8/4/6mm fixed lens, resolution 2560 x 1920 @15 fps , 25-30 mts length range |
| 32 | Supply and installation of 24 Port PoE switch for CCTV IP camera (Higher end) |
| 33 | Supply and run of CAT 6 unarmoured cable in existing PVC pipe/truf including termination work. |
| 34 | Supply and Run of 19mm PVC rigid pipe concealed in wall and ceiling and making good of the concealed position. |
| 35 | Supply and laying of 6 core outdoor armoured OFC cable in exisitng PVC pipe/ HDPE pip |
| 36 | Supply and Laying of HDPE pipe of size 50/38mm in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good |
| 37 | Supply and clamping of HDPE pipe of size 50/38mm on wall or ceiling with suitable MS clamps |
| 38 | supply and installation of 43 inches LED monitor with full HD with following features. Resolution 1920 x 1080, HDMI , audio in, built in speaker , 24/7 operation. |
| 39 | Supply and Installation of 8TB built in Hard Disc drive |
| 40 | Supply and Installation of 32 channel Network Video recorder with 2 sata , (2 Nos. Hard disc) recording minimum 720P resolution in full HD , Hard disc support 4TB, USB, HDMI should be available with all accessories |
| 41 | Supply and Installation of 30W wall mount speaker.Make:Bosch/Eq. Model No:LB2-UC30-L1 |
| 42 | Supply and Installation of 2 core 1.5 Sq.mm Speaker cable in existing pvc pipe on wall and ceiling. Make:Orbit/Eq. |
| 43 | Supply and Installation of 12U floor standing rack with power sockts and lock & key facilities. 700mm width x 600mm deot tray steel audio equipments rack which consists of power sockets, Lock - key front glass door, rear metal door with caster\"s set and other accessories |
| 44 | Supply and Installation of 500W PA Mixer Amplifier (Higher end) Please Enable Macros to View BoQ information |
