|
| 1 | Demolition of brick work built in cement mortar complete all as specified and as directed. |
| 2 | M&L brick work with fly ash \"bricks(FASB) confirming to IS 12894, of strength M-10 straightor curved on plan exc 6m mean radiusbuilt cement mortar 1:6 complete all as specified and as directed. |
| 3 | Taking out /Dismantlingof existing roof treatment of any description , any position over roof including taking out plain cement concrete of any description to the thckness as directedetc complete and including lowering down complete waste materials to the ground on a place where directed and includingremoval of the same to a distance exc 250 mtr but n exc 500 mtr as directed . Note : The cost of lowering down and removal deemed included in unit rate quoted by the tenderer. |
| 4 | M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof and leveling course etc finished and laid to required slope complete all as specified and as directed. |
| 5 | M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stilgreen finished even and fair including mixing ofwater proofing compound as per manufacturer instructionetc complete all as specified and as directed.Note :- Water proofing compound shall be measured separately assupply. |
| 6 | Supply only integral water proofing compound complete all as specified and as directed. |
| 7 | M&L applying water proofing treatment with the following-(a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated.(b) after the application of approved bituminous primer the water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction.(c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membranecomplete all as specified and as directed. |
| 8 | M and L for preparation of newly surface of APP membrane and Apply two coat of bituminous aluminum paint @ 200 gm / Sq.M. complete all as specified and as directed. |
| 9 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each etc complete. |
| 10 | -do- but exc 1.5 Sqm and n exc 4 sqm each. |
| 11 | S&F powder coated aluminium sliding windows (three track frame of weight not less than 1.17 Kg/Rm) with one fly proof shutters and two glazed shutterhaving top rail of section 41mmx20mmx1.6mm thick, bottom rail of section 41x20x1.6mm thick ,vertical style of section 38x20x1.6mm thick including necessery jointing cleats ,glazing clips, rubber packing ,snap beading, screws handle and locking system etc, fitted including usingg standard aluminium section including necessery fittings and fixtures complete all as specified and directed. Note: (i) All rate i.e track frame, shutter, glazing cleat, rubber gasketetc is deemed included in quoted rates. (ii) Wiremess & glass pane will be measured & paid seperately with respective items. |
| 12 | S&F framed work such as grills, grating, etc, with ends of bars shouldered and or riveted, or froged in to spikes framed guard bars, barred iron doors, ladders, or similar work confirming to Fe 290 Gde-E-165complete all as specified and directed. |
| 13 | M&L for preparation of newsteel surfaces of any description over 10 cm width or girth and applying twocoats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed. |
| 14 | S&F galvanized mild steel wire cloth 0.63 mm nominal dia of wire and avg width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed. |
| 15 | Supply and fix 4.0mm thick Sheet glass, ordinary qualityduly covered with tinted solar control film, including jointing cleats, glazing clips, rubber packing, aluminium anodised snap beading,complete all as specified and as directed by the Engr-in-Charge. |
| 16 | S&F 125 mm x 60 mm size pressed steel frames for door with one or more rebates including necessary fixing lugs, hinge lock strike plate ect including one shop coat of red oxide primer including cutting holes and making good in PCC 1:2:4type B1 using 20mm graded stone aggregate complete all as specified and as directed.Note :- 10 mm deformed bar shall be provided in bottom & PCC will be provided in hollowframe in same rate. |
| 17 | Supply and fix for 30 mm thick locally made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified. |
| 18 | S&F 30mm thick 2nd class hard woodGlazed and skeleton shutters (locally made), open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) fitted to chowkhats complete all asspecified and as directed by the Engr-in-Charge. |
| 19 | M&L two coat synthetic enamel paint over one coat of pink primer on new wooden surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed |
| 20 | S&F 200mm long Aluminium, anodised, barrel tower bolts of extruded sectioncomplete all as specified and as directed by the Engr-in-Charge. |
| 21 | S/F 150 mm size Aluminium handles, cast type, anodised and fixed of approved make & ISI marked complete all as specified and directed. |
| 22 | S&F 250 mm long aluminium alloy anodised sliding door bolts with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed by the Engr-in-Charge. |
| 23 | M&L Anodised aluminium frame straight for doors/windows/partitions using aluminium section of minimum size 100x44mmx1.60mm thick fixed in position by means of steel screws and patent rawl plugs / bolts / hold fasts of suitable size complete all as specified and directed. |
| 24 | S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, nodised aluminum snap beading screws etc. including jointing cleats, glazing clips, rubber packing, aluminium anodised snap beading, screws, anodised aluminium fittings such as hinges (B-21) handles (disc type), tower bolts (200mm long), locking device with duplicate keys complete all as specified and directed. |
| 25 | S&F Aluminium die cast body door closer hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 Kg and fixed in repair complete all as specified and as directed. |
| 26 | Taking down 15 mm bore steel tubing and connection including cleaning and removal to store etc complete all as specified and directed. |
| 27 | Taking down 20 mm bore steel tubing and connection including cleaning and or removal to store etc complete all as specified and directed. |
| 28 | S&F 15 mm bore galvanised mild steel tubing of medium grade with all fittings & fixed complete to walls & ceiling or laid in trenches/floors etc complete all as specified and directed. |
| 29 | S&F 20 mm bore galvanised mild steel tubing of medium grade with all fittings & fixed complete to walls & ceiling or laid in trenches/floors etc complete all as specified and directed. |
| 30 | Taking down/Dismantling old existing unserviceable HDPE water storage tank(PVC/RCC)and of capacityexc 500 ltrs but n exc 1000 ltr etc complete all as specified and directed. |
| 31 | S&F 1000 Ltr capacity of rotational moulded polyethylen water storage tank three layered (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600 mm long with fittingcomplete all as specified and as directed by the Engineer-In- Charge. |
| 32 | S & F in repair 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. |
| 33 | S&Fin repair20 mm boreBall valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 15mm-142gms/ 20mm-210 gms./25mm-455gms/ 40mm etc complete all as specified and directed. |
| 34 | Demolition of cement concrete (unreinfored )in ground floor and paving n,exc 15cm thickness below or above ground level)complete all as specified and as directed |
| 35 | M&L for 75 mm thick cement concrete 1:3:6type C1 ,using 20 mm graded crushed stone aggregatesas in plinth protection/path laid in alternate panel , joint filled with bitumen 85/25, surface finished even and smooth complete all as specified and as directed. |
| 36 | Taking down cement plaster on brick or stone walls etc incl racking out joints hacking for key and scrabbing down with water etccomplete all as specified and directed. |
| 37 | M&L renderig 15mm thick in cementmortar 1:6 over faces of of brick or concrete surface of wall rendering is to be finished even and smooth without using extra cementcomplete all as specified and as directed. |
| 38 | M & L for preparing of new surface andapplying two coat of weather proof paint over a coat of alkali resistant priming paint on external surface complete all as specified and as directed. |
| 39 | M & L for preparing of new surface andapplying two coat of oil emulsion distemper over a coat of alkali resistant priming paint on internal surface complete all as specified and as directed. |
| 40 | M & L preparing surfaces of wall by complete removal of existing treament andapplying two coat of weather proof paint on external walls complete all as specified and as directed. |
| 41 | M & L preparing surfaces of wall by complete removal of existing treament andapplying two coat of oil emulsion distemper on walls complete all as specified and as directed. |
| 42 | M&L preparing old decorated plastered or unplastered surfaces of Ceiling, pilasters, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spot and applying one coat of white wash on ceiling complete all as specified and as directed. |
| 43 | M&L for a coat of JK/Birla wall care putty 1mm thick including preparation of surface complete all as specified and as directed. |
| 44 | Dismantling floor hearth wall tiling including cement mortar bedding but not backing removing serviceable meterial to store complete all as specified and directed. |
| 45 | M&L for Virified Ceramic tiles in any colour 8 to 9 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed or bedding layer in cementy mortar 1:6etc complete all as specified and directed. |
| 46 | M&L for Virified Ceramic tiles in any colour 8 to 9 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , in vertical surfaces such as skirtings/dados or risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 10mm thick rendering in cement mortar 1:4 etc complete all as specified and directed. |
| 47 | M and L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including Screed bed or bedding layer or mortar 15mm layer of mortar 15mm thick for laying floor finishes with CM (1:6)complete all as specified and directed. |
| 48 | M & L for Kota stone slab 15-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15 thick Rendering cement mortar 1:6 complete all as specified and as directed. |
| 49 | M&L Cement concrete in foundations/sub base, filling and mass concrete 1:4:8 type D2 (using 40mm graded stone agg) complete all as specified and directed. |
| 50 | M&L for machine pressed precast concept interlocking paver block of local make availableany shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade with grey cement and no pigment over 50 mm thick sand bed complete all as specified and as directed.Note for item No 50 : Sand bed measured & paid sperately. |
| 51 | M&L for50mm thick sand cushioing to under concrete interlocking paver block including watering & consolidation complete all as specified and as directed. |
| 52 | Taking down carefully copper/ aluminium point wiring (light, fan, socket, or power) complete fitting such as switches, ceiling roses pendants, regulators, sockets, light fitting ceiling fan etc to be measured seperately ) removing materials for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperatly) and making good disturbed surface of walls floors etc all as specified and directed. Note-Responsibility after taking down fan/exhaust fan keep in safe custody of contractor and refix the same afterbefore completion of work the rate of same deemed to be included in the item quoated rate. |
| 53 | Taking down carefully sub main wiring / service connection twin core from wall / LT pole of any size of Aluminum with wooden batten and or through rigid conduit including GI wire and making good the disturbed surfaces of walls, roofs, floors etc complete all as specified and as directed. |
| 54 | M & L for concealed point wiring One light point controlled by one switch complete with PVC insulated and unsheathed flame retardant low smoke and halogen ( FRLSH ) cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 20 mm dia, clip, with MS terminal boxes (not less than 1.6mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dollywith3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green multi stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed. |
| 55 | S&F switch pianoflush button type 5 Amp single pole one waycomplete all as specified and asdirected. |
| 56 | S&F ceiling rose,surface bakelite63.5mm dia three terminals completeall as specified and asdirected. |
| 57 | M&L, sub main wiringwith two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 1.5 sqmm size drawn in and includingnon metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 20 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed.(NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chasesin wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface. |
| 58 | Supply and fix LED 45 W building security light fitting,5700 K energy saving & environmental friendly long life versatile pressure die cast aluminiumIP 66.road way luminare with high power LEDs as light source and electronic driver suitable for pole dia 35 mm including 35 mm dia light grade tube bracket ,bend to shape 1.80 mtrlength with two nos of clamps of size 50mm x 6mm with nuts and bolts,washers etcincluding connection with 1.5sqmm threesinglecorePVC insulated and PVC sheathed cable stranded copper cable upto ceiling rose and fixing on walls/pole complete all as specified and directed. |
