Tender For Construction Of Admin Block At Western Command Hqr Chandigarh., Chandigarh-Chandigarh

TDR : 53499786

Tender Notice
BOQ

8 Days Left

Chandigarh , Chandigarh

Tender Brief : Tender For Construction Of Admin Block At Western Command Hqr Chandigarh.

Document Fees
Refer document

EMD
₹ 2481775.0 /-

Tender Value
Refer document

Submission Date
07-02-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil
2	Excavating trenches by mechanical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia
3	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
4	Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.
5	Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m. All kinds of soil.
6	Earth work by mechinical / manual means in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonneroller or wooden or steel rammers, and rolling every 3rd and top-most layer with power rollerof minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginalbanks and guide banks or filling up ground depressions, lead upto 50 m and for all lift
7	Supplying chemical emulsion in sealed containers including delivery as specified . Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
8	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
9	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
10	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
11	Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns
12	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).
13	Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification.
14	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.
15	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
16	Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for massconcrete
17	Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.
18	Lintels, beams, plinth beams, girders, bressumers and cantilevers
19	Columns, Pillars, Piers, Abutments, Posts and Struts.
20	Stairs, (excluding landings) except spiral-staircases.
21	Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.
22	Edges of slabs and breaks in floors and walls Under 20 cm wide
23	Weather shade, Chajjas, corbels etc., including edges.
24	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
25	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
26	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.5.33.1 All works upto plinth level5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum
27	5.33.2 All works above plinth level upto floor V level5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum
28	Add for using extra cement in the items of design mix over and above the specified cement content therein.
29	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
30	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)
31	Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand)
32	Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).
33	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm
34	Area of slab over 0.50 sqm
35	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
36	Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete.
37	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
38	Extra for Providing and fixing flush doors with both side decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)
39	Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
40	Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm.
41	Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.
42	Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.Double strip (horizontal type).
43	Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.200 mm
44	Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-charge.
45	Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.
46	Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. 30 mm thick plain PVC door shutters.
47	Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge
48	Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.
49	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 300x10 mm
50	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 200x10 mm
51	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm
52	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10 mm
53	Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.
54	Providing and fixing aluminium handles of approved make anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessry screws etc. complete. 125 mm
55	Providing and fixing aluminium handles of approved make anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessry screws etc. complete. 100 mm
56	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper
57	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineerin-charge.
58	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick
59	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows, Doors and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With aluminium Snap beading.
60	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds. Casement Window with Double Rebate Frame with two Side Hung Glazed Panel and two Side Hung wire mesh Panel and Fixed Mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles on both glazed and fly screen panel. Using R3 series with frame (110mm & above ) x (45mm & above) & glazed sash (55mm & above) x (65mm & above) & fly screen sash (30mm & above) x (55mm & above) & mullion (55mm & above) x (65mm & above) & metal grill (if required to be paid separately). (Height upto 1.8 meter) Fixed window / ventilator with mullion / transom.
61	9.147.A4.3 Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height above 1.8m)
62	Ventilator Casement window single panel with or without fixed panel with S S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R1 series with frame (33mm & above ) x (35mm & above) & sash /mullion (33mm & above) x (50 mm & above). (Height upto 0.90 meter).
63	Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
64	Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete.
65	Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 60 mm
66	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
67	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
68	Extra for pre finished nosing to treads of steps of marble / granite stone.
69	Extra for marble / granite stone flooring in treads of steps and risers using single length up to 2.00 metre.
70	11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.1.4 Size of Tile 800 x 1600 mm
71	Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 800 x 800 mm
72	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/RubyRed or equivalent
73	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase
74	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
75	12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
76	15 mm cement plaster on rough side of single or half brick wall of mix :1:6 (1 cement: 6 coarse sand)
77	20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)
78	Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.
79	Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 10 to 13m
80	Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 13 to 16m
81	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.
82	Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work
83	8.32 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shopdrawings and as directed by the Engineer-in-Charge. However, for the purpose of payment,only the actual area on the external face of the curtain wall with Aluminum Composite PanelCladding (including width of groove) shall be measured in sqm. up to two decimal places.
84	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (40x40x6mm = 3.5kg/m)
85	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
86	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
87	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
88	Providing and fixing glazing in UPVC/ aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
89	Filling the gap in between aluminium frame and adjacent RCC/Brickwork/ Stone Work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge. Upto 5mm depth and 5mm width
90	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
91	Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Boardwith BIS certification marks)
92	Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
93	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
94	Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer
95	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm
96	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
97	Supply, Receiving, Storing & Fixing of CP brass wall mounted sink mixer with C.P. wall flange, swinging spout complete as required with flow rate of 6.0 LPM complying to Green Building requirements.
98	Providing,fixing,testing and commissioning Hand Shower (Health Faucet) with 8mm Dia,1 Metre Long Flexible Tube & Wall Hook of approved make and manufacture complete as per direction of Engineer in Charge.
99	Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.
100	Providing and fixing toilet paper holder C.P. brass
101	Supply, Receiving, Storing & Fixing of C.P. brass twin coat hook with PVC rawl plug & C.P. brass screw complete as required. Make :
102	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore
103	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
104	Providing and fixing Chromium Plated towel ring Rectangular shape with concealed fittings arrangement of approved quality and colour, of approved brand & manufacture complete as per direction of Engineer in Charge.
105	Providing and fixing of C. P. brass towel rail 600 x 20 mm size complete with C.P. brass brackets.
106	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
107	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe. 40 mm dia
108	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm dia nominal bore
109	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm dia nominal bore
110	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm dia nominal bore
111	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 50 mm dia nominal bore
112	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 65 mm dia nominal bore (Sch. 40)
113	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes
114	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes
115	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20mm nominal bore
116	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25mm nominal bore
117	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32mm nominal bore
118	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40mm nominal bore
119	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50mm nominal bore
120	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65mm nominal bore
121	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore
122	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore
123	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
124	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks ofclass designation 7.5
125	Providing and fixing motorized valve with sensor of approved quality, to complete the work. 40 mm dia
126	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 110 mm (For Single & public toilets Soil & Waste Pipe).
127	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 75 mm (For Vent Pipe).
128	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 40 mm dia (For Urinal Soil Pipe).
129	Supplying, Installation, Testing and Commissioning of (PP/PP mineral), P or S trap of self cleansing design with / without vent. arm Setting in cement concrete 1:2:4 mix complete including cost of cutting & making good the Wall / Floors wherever required. 110 x110 mm outlet
130	Providing and fixing (PP/PP mineral) floor drain 110X75 size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects.
131	Providing & fixing (PP/PP mineral) clean out plug with uPVC socket fixed to uPVC pipe joints as required complete in all. 100 mm dia Pipe
132	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe
133	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 75 mm dia pipe
134	Providing and fixing chrome plated grating with ring and two S.S screws of approved design with grating screwed down to the ring with s/s screws and embedding and setting ring into the floor with cement mortar.
135	Providing and fixing uPVC cowel of approved quality 110 mm
136	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.450 X 450mm -
137	Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
138	Supplying, Installation, Testing and Commissioning of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) for rain water pipes including all fittings rubber ring type (plain or with access door) e.g. bends, junctions, cowls, offsets, access pieces, jointing with rubber ring joints with lubricant etc. fixed with clamps to walls with cement concrete 1:2:4 blocks complete in all respects. (For rain water Pipe). 75 mm diameter
139	Supplying, Installation, Testing and Commissioning of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) for rain water pipes including all fittings rubber ring type (plain or with access door) e.g. bends, junctions, cowls, offsets, access pieces, jointing with rubber ring joints with lubricant etc. fixed with clamps to walls with cement concrete 1:2:4 blocks complete in all respects. (For rain water Pipe). 110 mm diameter (with all fittings)
140	Supplying and laying of following size HDPE DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 150 mm dia. Pipe
141	Supplying and laying of following size HDPE DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 200 mm dia. pipe
142	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 150 mm dia. DWC & RCC Pipe
143	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 200 mm dia. DWC & RCC Pipe
144	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 250 mm dia. DWC & RCC Pipe
145	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 150 x 100mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
146	Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
147	Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
148	Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
149	Extra for depth for manholes :Size 90x80 cm, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
150	Extra for depth for manholes Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
151	Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
152	Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture\"s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
153	Making connection of drain or sewer line with existing manholeincluding breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter
154	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit with modular switch modular plate suitable GI box and earthing the point with 1.5 sq.mm FRLS / HFFR PVC insulated copper conductor single core cable etc.as required. Group C
155	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS / HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS / HFFR PVC insulated copper conductor single core cable etc. as required. Group C
156	Wiring for power plug points with 2 x 4 sq.mm. FRLS / HFFR PVC insulated, Cu. Conductor, single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq.mm. FRLS / HFFR PVC insulated copper conductor single core cable for loop earthing as required.
157	Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS / HFFR PVC insulated, Cu. Conductor, single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq.mm. FRLS / HFFR PVC insulated copper conductor single core cable for loop earthing as required.
158	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 1.5 sq.mm. + 1 x 1.5 sq.mm. earth wire.
159	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
160	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
161	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
162	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
163	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
164	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
165	Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.
166	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
167	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non-residential buildings).
168	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
169	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet (near equipment point) and 25 A modular SP MCB, “C” curve (at accessible point) including connections, painting etc. as required.
170	Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
171	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
172	Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
173	Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.
174	Suppliying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc.as required. TV antenna socket outlet
175	Suppling and drawing co-axial TV cable RG-6 grade , 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC shealth in the existing surface/recessed steel/ PVC conduit as required.
176	Supply, Installation, Testing & Commissioning of CAT 6A UTP LSZH Cable, 23 AWG solid copper conductors in accordance to TIA/EIA 568 C.2 (Category 6a) & ISO/IEC 11801 2nd ed(Class Ea), UL Approved, tested @500 Mhz, with HDPE insulation of individual conductor and over all Dia of 7.2 mm for Connectivity of Hub room to End Point. Grey Color.
177	Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.
178	Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6A UTP, loaded Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.
179	Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.
180	Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.
181	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)
182	Supply, Installation, Testing & Commissioning of 15 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. & 5Nos. 6/16A sockets PDU also complete as required.
183	Supplying and fixing of following sizes of Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
184	Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in the cubical panel, making connections etc. as required. (for VTPN DB) 100/63 A,36KA,FP MCCB
185	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 8 Way (4+24), Double Door
186	Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way Double door (4 + 24)
187	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface / recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB
188	Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required.
189	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
190	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole
191	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole
192	Supplying and fixing of following rating, four pole 415 V , Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amp
193	Supplying and fixing of following rating, four pole 415 V , Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp
194	Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. 40 Amps
195	Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. 63 Amp
196	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 8-10WATT
197	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 12-15 WATT
198	LED Batten light (System lumen efficacy ≥105 <120lm/Watt) Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) 18-22 WATT
199	LED Batten light (System lumen efficacy ≥105 <120lm/Watt) Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) 40watt
200	Supplying and fixing single wall mounted 9/10 watt (2ft long) LED type batten fitting complete with electronic driver and LED etcdirectly on wall/ceiling including connections with 1.5sq.mm FRPVC insulated copper conductor and earthing the body etc. as required.
201	Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1400 MM Ceiling fan
202	Supplying and fixing of 250mm sweep heavy duty Exhaust fan with all accessories suitable for operation single phase 230 volt 50 cycle per second per sec. AC supply etc. as required. in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning earthing etc. as required.
203	Supplying, Installation, Testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 3 meter and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required
204	Design, Manufacturing, Supply, Installation, Testing & Commissioning of cubicle type totally enclosed free standing / Wall mounted type moisture, dust and vermin proof compartmentlized Floor Distribution Panel made out of 2.0 mm thick of Main members & front cover 1.6 mm thick CRCA sheet complete with internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. y. The MCCB rating up to 250A shall have thermal megnatic based adjustable over current, short circuit protection and above 250A MCCB shall have microprocessor based adjustable over current, short circuit, earth fault protection. All Main Distribution board / Sub Distribution board / Meter boards which are located inside various blocks shall be partially Type Tested assemblies (PTTA) as per conforming to IEC-61439-1 The Moulded Case Circuit Breaker shall have a minimum fault breaking capacity (Ics) of not less than 35 KA & 25KA RMS for one second at 415 volts for MDB / SDB respectively. MCCB‘s above 63A should be provided with Copper & procader terminals. Incomer of Meter Board shall have a minimum short circuit breaking capacity (Ics) of 25KA for one second at 415volt.INCOMING, 1 No. 200 Amp FP,36KA, Moulded Case Circuit Breaker1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.1 NO. SPD with Protection fuse.BUSBAR, 250 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.OUTGOINGS, 1 No125 Amp FP,25 KA, Moulded Case Circuit Breaker3 No100 Amp FP,25 KA, Moulded Case Circuit Breaker2 No 63 Amp FP,25 KA, Moulded Case Circuit Breaker1 Nos. 63 Amp DP Miniature Circuit Breaker.Panel described as above
205	All floor PanelINCOMING1 No. 125 Amp FP,25KA, Moulded Case Circuit Breaker1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.BUSBAR, 150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOINGS, 4 Nos. 63 Amp FP Miniature Circuit Breaker.3 Nos. 40 Amp FP Miniature Circuit Breaker.Panel described as above
206	Earthing with GI earth Pipe 4.5 mtr long 40 mm dia including accesories and providing masonary enclosure with cover plate having locking arrangement of 2.7 mtr long etc with charcoal/cock and salt as required
207	Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
208	Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
209	Providing and fixing GI tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
210	Providing and fixing GI tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
211	Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.
212	Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.
213	Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
214	Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
215	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 3.5 core, 95 sq.mm.
216	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 3.5 core, 50 sq.mm.
217	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 10 sq.mm.
218	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 25 sq.mm.
219	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc.as required. Upto 35 sq. mm (clamped with cable tie)
220	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray/surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie)
221	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 95 sq. mm (45mm)
222	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 50 sq. mm (35mm)
223	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 25 sq. mm (28mm)
224	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 10 sq. mm (25mm) (used for 4 x 6 sq. mm & 4 x 4 sq. mm cable)
225	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.inclunding Bends & TEE etc. 100 mm width x 50 mm depth x 1.6 mm thickness
226	Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520, (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-\"F\" insulation, conforming to IS-325. (D) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (E ) Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head (1W+1S)
227	Supplying and making end termination with brass compressiongland and aluminium lugs for following size of PVC insulated andPVC sheathed / XLPE aluminium conductor cable of 1.1 KV gradeas required. 4 x 25 sqmm ( 28 mm )
228	Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred. 4 core, 25 sq.mm. Aluminium Armoured
229	Providing, fixing, testing and commissioning of control panel for Terrace Booster pumps .Incoming: MCCB 35A 1 set of Phase indicating lamps, 1 set of 35A Al bus bars, 1No Ammeter, 1No Voltmeter with phase selector switch Feeder for Booster Pumps - 1 No. 1 No. 32A TP MCCB without releases. DOL starter with over load relay, single phase preventor and indicating lamps with ON/OFF push buttons. 2No. Automanual selector switch. Suitable for booster pumps
230	Providing & fixing of heavy class M.S. pipes conforming to IS: 1239/3589 complete with fittings including trenching and refilling etc. (external work) including all fittings and accessories like tees, elbows, flanged joints, rubber insertion, nuts, bolts or cutting and welding joints. Providing thrust block at distance specified as per specifications. (Pipe shall be provided with anti corrosive protective treatment with coal tar/asphalt tape confirming to IS: 10221 standard complete as per specification). All work complete as per specification and as directed by Engineer-In-Charge. (All the fitting i.e. tee /elbow etc. for Valve connections etc. will be flanged joints)( Heavy duty pipe 80 mm dia
231	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (The Welding shall not be done for piping less than 50 mm dia.) 80 mm dia
232	Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless Steel (Internal)
233	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. 80 mm dia
234	Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia
235	Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80 mm dia
236	Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)
237	Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
238	Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.40 m
239	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)
240	Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way - 100 mm dia M.S. Pipe
241	Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
242	Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
243	Providing & fixing heavy duty double flanged flexicon rubber expansion joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required. 80 mm dia
244	Supplying and fixing fire hose cabinet fabricated from 16 gauge M.S. Sheet with single or double glazed front door (with 4 mm thick glass) and locking arrangement, painted fire red with stove enamelled paint \"FIRE HOSE\" written on front including necessary supports approximate size. a)750mm x 600mm x 250mm deep. (Internal only for hose reel)
245	Supplying and fixing of Fire Man\"s axe with heavy insulated rubber as per standard conforming to IS 926.
246	Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge. 4.5kg capacity cylinder
247	Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge. Dry Chemical Powder ABC type of 6 Kg as per IS:15683
248	Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressorand Printed Circuit Board (PCB). Must comply : Electricalcable IS 694 or IS 9968 temperature sensing control IS/International Electrotechnical Commission (IEC) 60730,hermetic compressor IS 10617, heat exchanger IS 11329,capacitor IS 2993 and motor IS 12615. Complete as perCPWD specification and IS : 1391 Part II 2023. The systemshall be able to operate up to 50 0C (out door ambienttemperature).Inverter Type - Cooling only1.5 TR with 5 Star BEE Rating
249	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (suction line)(2.0 TR) -6.4 mm dia
250	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (Liquid line)(2.0 TR)-12.7 mm dia
251	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (suction line)(1.5 TR)-6.4 mm dia
252	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (Liquid line)(1.5 TR)-12.7 mm dia
253	Providing and fixing factory fabricated floor/wall mounted type MS angle iron frame suitable for installing of split AC outdoor unit material etc as required.
254	manufacturing, supplying, and fixing of stainless steel, grade 304 letters IN ENGLISH for the \"BUILDING NAME\" sign, each letter designed and fabricated with a 50mm raise from the mounting surface 18 inch size using concealed SS studs and as per approved font, size, and finish. The SS 304 material must be ISI-marked, such as Jindal or Apollo brands, and the surface finish should be brushed or mirror-polished as required by the architectural intent
255	manufacturing, supplying, and fixing of stainless steel, grade 304 letters in HINDI for the \"BUILDING NAME\" sign, each letter designed and fabricated with a 50mm raise from the mounting surface 18 inch size using concealed SS studs and as per approved font, size, and finish. The SS 304 material must be ISI-marked, such as Jindal or Apollo brands, and the surface finish should be brushed or mirror-polished as required by the architectural intent
256	Supplying & laying of drainage composite for use behind walls, between two different fills, alongside drains of road, below concrete lining of canals etc. Geocomposite for planar drainage, realized by thermobonding a draining core in extruded monofilaments with two filtering nonwoven geotextiles that may also be working as separation or protecting layers. The draining three dimensional core will have a “W” configuration as longitudinal parallel channels. Minimum thickness to be 7.2mm, with two filtering UV stabilized polypropylene nonwoven geotextile of minimum thickness of 0.75mm characteristic opening size (090) of 110 micron and tensile strength of 8.0 KN/m that will be working as separation or protecting layer, geocomposite having in plane flow capacity of 2.1 L / (m.s) at hydraulic gradient of 1.0 & 20 kPa pressure and tensile strength of 18 kN/m , with mass per unit area of 740 gsm, supplied in the form of roll for easy transportation to site of work as per detailed specification all complete as per directions of Engineer in charge.
257	Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.
258	Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).
259	Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineerin- charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:-Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer
260	Extra for providing and mixing hardening compound of approved quality as per manufacturer’s specification in cement concrete.
261	Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in-charge.
262	Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineerin-Charge. 60mm thick C.C. paver block of M-35 grade with approved colour, design & pattern.
263	Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
264	Providing and laying 100 micron thick Pvc Sheet (Overlaps at joints of PVC Sheet should be 100mm wide and pasted to each other with suitable adhesive over WMM road surface as per the direction of Engineer-in-Charge.
265	Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 mm
266	Fine dressing of the ground.
267	Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
268	Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge
269	Grassing with selection No. 1 grass including watering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and earth shall be paid for separately). With grass Turf
270	Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)
271	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep
272	Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
273	Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.
274	Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy plant in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.
275	Supply and stacking of Bauhinia blakeana (Kachnar) plant of height 120- 150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
276	Supply and stacking of plant Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.
277	Supply and stacking of plant Tabernaemontana coronaria (Chandni single) of height 90-105 cm,bushy in big size HDPE bag as per direction of the officer-in-charge.
278	Supply and stacking of plant Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.
279	Supplying and placing in position of Danbury Director\"s Desk with Leatherette Desk Pad size :- (W)2000mm X (D)1000mm X (H)760mm. Table Top Thickness : 80mm. Our Danbury office collection is a study in blending timeless elegance with practical design. The masterfully curved silhouette puts the spotlight on intricate moulding and elegant panel design with a leatherette accent. Designed with a movable drawer pedestal and side runner, this director’s desk ensures a clutter-free work area, while the leatherette desk pad and cable organizer add a functional flair. Crafted from premium engineered wood in Walnut finish. Spacious tabletop offers ample workspace, ideal for multitasking and large projects. Gently curved silhouette with intricate moulding and leatherette accent adds a statement appeal. A leatherette desk pad offers a smooth and durable surface for writing and daily tasks. A movable pedestal unit features 3 spacious drawers. A side runner size :- (W)790mm X 650mm(H). runner features 1 cabinet, 1 drawer, 1 shelf, a dedicated CPU shelf and a trolley. A keyboard trolley offers a clutter-free workspace. 2 Circular cable organisers keep the tabletop clutter-free. A dedicated CPU unit keeps your CPU neatly stored, leaving your desk clutter-free. Premium PU polish with low chemical emissions ensures healthy indoor air.Supplying and placing in position of Danbury Director\"s Desk with Leatherette Desk Pad size :- (W)2000mm X (D)1000mm X (H)760mm. Table Top Thickness : 80mm. Our Danbury office collection is a study in blending timeless elegance with practical design. The masterfully curved silhouette puts the spotlight on intricate moulding and elegant panel design with a leatherette accent. Designed with a movable drawer pedestal and side runner, this director’s desk ensures a clutter-free work area, while the leatherette desk pad and cable organizer add a functional flair. Crafted from premium engineered wood in Walnut finish. Spacious tabletop offers ample workspace, ideal for multitasking and large projects. Gently curved silhouette with intricate moulding and leatherette accent adds a statement appeal. A leatherette desk pad offers a smooth and durable surface for writing and daily tasks. A movable pedestal unit features 3 spacious drawers. A side runner size :- (W)790mm X 650mm(H). runner features 1 cabinet, 1 drawer, 1 shelf, a dedicated CPU shelf and a trolley. A keyboard trolley offers a clutter-free workspace. 2 Circular cable organisers keep the tabletop clutter-free. A dedicated CPU unit keeps your CPU neatly stored, leaving your desk clutter-free. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
280	Tables For PA :-Supplying and placing in position of L- shaped desk as per image. The primary work surface over all size is 1500mm(L) x 750mm (D) x 750mm(H) with 25mm thick table top made of prelaminated particle board work surface with wenge finish, using hot melt glue to fixing 2mm thick pvc edge banding made of same matte finish. side pannel is made of 25mm thick. Provision of side runner of size is 750mm (L) x 450mm (D) x 760mm (H) . Construction is from right side of side unit top based on fixed pedestal with ss stud of grade 304, on table top pvc groment hole for wire management . Provision of fixed pedestal of size 450mm (L) x 450mm (D) x 650mm (H) per drawer height is @ 136mm, filling drawer height is @ 300mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. Three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
281	D. Commandant:- Supplying and placing in position of Cabin table as per photograph. Table over all size is 1800mm(l)x 900mm(d)x 750mm(h) 50mm thick table top made of prelaminated particle board work surface with classic wenge brown finish 2mm thick pvc edge banding made of same matte finish. side pannel is made of 50mm thick. Provision of side runner of size is 1200mm(l)x 400mm(d)x 760mm(h) ,(ccombination onstruction below table top 1 key board tray in pvc with telescopic channel on right side is movable side runner having 1 openable door with 1 fixed shelve, 1 open box with 1 fixed shelve upper shelve height is @ 320mm below shelve height is @324@ + 3 drawers (2 equal drawers + 1 filling drawer)per drawer height is @ 184mm, filling drawer height is @ 303mm have central lock and handles with castors . Mobile pedestal of size 400mm(l)x 530mm(d)x 671mm(h) ,per drawer height is @ 186mm, filling drawer height is @ 195mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
282	I.G. Room Table :-Supplying and Placing in Position of Primus Tiered L-Shaped Director\"s Desk size :- (W) 2000mm X (D) 1860mm X (H) 750mm. Table Top Thickness 50mm.The Primus Collection embodies the perfect harmony of curvaceous designs and clean-lined forms, blending sophistication with everyday practicality. This tiered L-shaped director’s desk, featuring a striking contrast of dark oak and lacquered beige finishes, makes a bold statement. Thoughtfully designed with a concealed switchboard and versatile storage, it ensures a clutter-free workspace, allowing you to focus on what matters most. Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish.Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish. A Dark Oak finish accentuates the unique grains & pattern of the wood. A solid lacquered finish adds a subtle contrast to the design. Spacious L-shaped tabletop offers ample workspace, ideal for multitasking and large projects. Concealed switchboard keeps the workspace clutter-free. 1 password-protected drawer, 1 shelf and 2 cabinets keep your essentials protected and within reach. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
283	High Back Chair Leather :-Supplying and Placing in Potition high back natural leather chair. High back 360° degre revolving chair , All over size is : 650mm(l)x 480mm(d)x 1300mm(h) , The chair made of full natural leather . it will comes in matte finsih about style type is modren. Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchromult-locking mechanism . Only seat size is 560mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1300mm & minimum height is 1240mm gas lift 60mm telescopic haudraulic,class 4 heavy duty gas lift for seat height adjustment bearing capacity 200kgs . Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
284	Low Back Chair Leather :-Supplying and Placing in Position of low back natural leather chair. Low back 360° degre evolving chair , All over size is : 650mm(l)x 510mm(d)x 1150mm(h) , The chair made of full natural leather . It will comes in matte finsih about style type is modren . Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchro multi locking mechanism . Only seat size is 580mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1150mm & minimum height is 1090mm gas lift 60mm telescopic haudraulic , Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
285	High Back chair Leatherrete :-Supplying and placing in position of high back 360° degre revolving chair All over size is : 590mm(l)x 505mm(d)x 1280mm(h) , the chair made of full leatherette .It will comes in matte black finish finsih in contemporary style . Details :- Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat . Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support . Mechanism : knee tilt mechanism . Only seat size is 505mm(l)x 505mm(d)x 610mm(h) & the back size is 590mm(l)x 710mm(h) Seat maximum height is 610mm & minimum height is 510mm & back height from floor maximum height is 1280mm & minimum height is 1180mm ; Gas lift 100 mm telescopic haudraulic . Base : 650 mm chrome base with smooth castors .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
286	Visitor Chairs :- Supplying and placing in position of fix cantilever chair, All over size is : 610mm(L)x 505mm(D)x 990mm(H) ,The chair made of full leatherette . It will comes in matte black finish in contemporary style . Details : - Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed BWR plywood (IS Grade - 303 for seat and back) .Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam , sign based on symmetrical lumbar support backrest support . Only seat size is 610mm(L)x 505mm(D)x 485mm(H) & the back size is 610mm(L)x 540mm(H) , Base : chrome finish tublar frame of cantilever type . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
287	High back mess Chair :-Supplying and placing in position of high back mesh chair with matte finish . The high back 360° degre revolving chair with all over size is : 640mm(l)x 670mm(d)x 1350mm(h) , It will comes in matte finsih about style type is modren. Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 815mm(h) , seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1350mm & minimum height is 1250mm . Gas lift 100 mm telescopic haudraulic ; base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
288	Midium Back Chair :-Supplying and placing in position of medium back 360° degre revolving chair ,All over size is : 640mm(l)x 670mm(d)x 1100mm(h) , The chair made of full mesh .It will comes in matte finsih about style type is modren. Details :- Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support, Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h) . Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm . Gas lift 100 mm telescopic haudraulic , Base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
289	Work Station with Partition :_ supplying and placing of non sharing single seater workstation of67mm thk sliding tile base partition of 1200mm height, overall size 1200mm x 600mm x 1200mm that is to be assembled at site. the work top shall have the size 1184mm x 592mm made up of 25mm thick pre- laminated particle board of grade ii type iii of is 12823/latest . of is level with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with polyester powder coating 40p-60p thick . the trims shall have the size 67mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways (l-cover for corner, t-cover for middle section wherever required). the aluminium raceway shall be situated below the worktop with an overall size 116mm(h) x 60mm(d) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft-board (with fabric) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (lan) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots/cut-outs should be given on raceways to fix all electrical and data points. single sided pvc wire manager should be enclosed at table top.adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor.particle board of grade ii of is level. Provision of mobile pedestal with key board tray & CPU trolly.
290	Mess visitor Chair :-Supplying and placing in position of fix cantilever mesh chair with matte finish, All over size is : 605mm(l)x 575mm(d)x 1010mm(h) , It will comes in matte finsih in contemporary style . Details :- Arms : pp fixed padded armrest . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h) , Seat max height is @ 470mm . Fixed cantilever chair with base : chrome plated tublar frame of catilever type .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
291	Two Seaters Sofa :-Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size is 1360mm(l) x760mm(d)x 790mm(h) shall have spring attached and also be padded separately. the seat shall have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience polyurethane foam having density 45kg/m³ in seat and 32kg/m³ in back.there shall be cushion arm provided padded with high resilience polyurethane foam having density 32kg/m³. The complete structure shall be upholsteredwith leatherite tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure shall consist of ms powder coated square pipe having cross-section area 25mm x 25mm with 1.6mm thick the legs shall be made up of powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 490 +/- 510mm(d) x 450 +/- 510mm(h).
292	Sofa for Visitor room :--Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W)2120mm X (D)1580mm X (H)920mm. Legs crafted with kiln-dried solid wood in Walnut French polish.Premium velvet fabric in beige feels soft and sumptuous.Tested with high rub counts, our fabric ensures high abrasion resistance.Soft seat, cushioned backrest and upholstered track arms offer a comfortable seating experience.A sleek leatherette band with 3 side pockets keeps your essentials within reach.3 complementary throw cushions add a layer of comfort while elevating the design.Anti-sag construction offers the right level of support for maximum comfort.Smooth finished edges eliminate moisture seepage, prevent warping and make it last longer.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
293	Sofa for IG Room :- Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W) 3200mm X (D) 3200mm X (H) 860mm.Sofa frame made of Kiln-dried solid wood ensures durability Breathable leatherette upholstery keeps your body cooler for longer Sleek metal legs make the sofa look airy and light 1 Dual USB port for convenient charging Adjustable backrest transforms the sofa into a lounger.Plush cushioned back and seat for comfortable seating Anti-sag construction offers the right level of support for maximum comfort High ground clearance, designed for modern Indian homes.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
294	Centre Table :-Supplying and Placing in Potition of Hopper Solid Wood Coffee Table size (W)1130mm X (D)630mm X (H)410mm. Inspired by the mid-century modern era, the Hopper collection flaunts clean silhouettes with tapered legs. Crafted with solid beech wood, the dark oak finish accentuates the distinctive wood grains. While the clear glass tabletop flaunts the charming wooden accent. The glass tabletop is made with sturdy glass, beautifully bordered by a solid wood frame. Designed for modern Indian homes, it makes a perfect spot to enjoy cozy talks over a cup of coffee. 8 mm Glass Top. Solid Wood Legs.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
295	Storages :-Suppling and fixing in position of customized ( factory made) Back Storage/ Filing unit with Pre laminate partical bord as approved colour of Depth 450 mm of required size ;- L-800mm x D-450mmx H-1800mm all complete as per direction and satisfaction of Engineer-in- charge :- Storage carcase, shelves and shutters shall be 18mm thick and storage backing shall be 9 mm thick Pre laminated partical board of grade ii type iii of is 12823/latest. The gap between 2 shelves should be range from 400 mm(+/-10 mm) as per the direction of EIC. - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature. - Each shutter should be fixed with 3 numbers SS butt hinges, round shape multipurpose lock, SS tower bolt of 100 x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved make.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
296	Supplying and placing in position of Danbury Director\"s Desk with Leatherette Desk Pad size :- (W)2000mm X (D)1000mm X (H)760mm. Table Top Thickness : 80mm. Our Danbury office collection is a study in blending timeless elegance with practical design. The masterfully curved silhouette puts the spotlight on intricate moulding and elegant panel design with a leatherette accent. Designed with a movable drawer pedestal and side runner, this director’s desk ensures a clutter-free work area, while the leatherette desk pad and cable organizer add a functional flair. Crafted from premium engineered wood in Walnut finish. Spacious tabletop offers ample workspace, ideal for multitasking and large projects. Gently curved silhouette with intricate moulding and leatherette accent adds a statement appeal. A leatherette desk pad offers a smooth and durable surface for writing and daily tasks. A movable pedestal unit features 3 spacious drawers. A side runner size :- (W)790mm X 650mm(H). runner features 1 cabinet, 1 drawer, 1 shelf, a dedicated CPU shelf and a trolley. A keyboard trolley offers a clutter-free workspace. 2 Circular cable organisers keep the tabletop clutter-free. A dedicated CPU unit keeps your CPU neatly stored, leaving your desk clutter-free. Premium PU polish with low chemical emissions ensures healthy indoor air.Supplying and placing in position of Danbury Director\"s Desk with Leatherette Desk Pad size :- (W)2000mm X (D)1000mm X (H)760mm. Table Top Thickness : 80mm. Our Danbury office collection is a study in blending timeless elegance with practical design. The masterfully curved silhouette puts the spotlight on intricate moulding and elegant panel design with a leatherette accent. Designed with a movable drawer pedestal and side runner, this director’s desk ensures a clutter-free work area, while the leatherette desk pad and cable organizer add a functional flair. Crafted from premium engineered wood in Walnut finish. Spacious tabletop offers ample workspace, ideal for multitasking and large projects. Gently curved silhouette with intricate moulding and leatherette accent adds a statement appeal. A leatherette desk pad offers a smooth and durable surface for writing and daily tasks. A movable pedestal unit features 3 spacious drawers. A side runner size :- (W)790mm X 650mm(H). runner features 1 cabinet, 1 drawer, 1 shelf, a dedicated CPU shelf and a trolley. A keyboard trolley offers a clutter-free workspace. 2 Circular cable organisers keep the tabletop clutter-free. A dedicated CPU unit keeps your CPU neatly stored, leaving your desk clutter-free. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
297	Tables For PA :-Supplying and placing in position of L- shaped desk as per image. The primary work surface over all size is 1500mm(L) x 750mm (D) x 750mm(H) with 25mm thick table top made of prelaminated particle board work surface with wenge finish, using hot melt glue to fixing 2mm thick pvc edge banding made of same matte finish. side pannel is made of 25mm thick. Provision of side runner of size is 750mm (L) x 450mm (D) x 760mm (H) . Construction is from right side of side unit top based on fixed pedestal with ss stud of grade 304, on table top pvc groment hole for wire management . Provision of fixed pedestal of size 450mm (L) x 450mm (D) x 650mm (H) per drawer height is @ 136mm, filling drawer height is @ 300mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. Three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
298	D. Commandant:- Supplying and placing in position of Cabin table as per photograph. Table over all size is 1800mm(l)x 900mm(d)x 750mm(h) 50mm thick table top made of prelaminated particle board work surface with classic wenge brown finish 2mm thick pvc edge banding made of same matte finish. side pannel is made of 50mm thick. Provision of side runner of size is 1200mm(l)x 400mm(d)x 760mm(h) ,(ccombination onstruction below table top 1 key board tray in pvc with telescopic channel on right side is movable side runner having 1 openable door with 1 fixed shelve, 1 open box with 1 fixed shelve upper shelve height is @ 320mm below shelve height is @324@ + 3 drawers (2 equal drawers + 1 filling drawer)per drawer height is @ 184mm, filling drawer height is @ 303mm have central lock and handles with castors . Mobile pedestal of size 400mm(l)x 530mm(d)x 671mm(h) ,per drawer height is @ 186mm, filling drawer height is @ 195mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
299	I.G. Room Table :-Supplying and Placing in Position of Primus Tiered L-Shaped Director\"s Desk size :- (W) 2000mm X (D) 1860mm X (H) 750mm. Table Top Thickness 50mm.The Primus Collection embodies the perfect harmony of curvaceous designs and clean-lined forms, blending sophistication with everyday practicality. This tiered L-shaped director’s desk, featuring a striking contrast of dark oak and lacquered beige finishes, makes a bold statement. Thoughtfully designed with a concealed switchboard and versatile storage, it ensures a clutter-free workspace, allowing you to focus on what matters most. Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish.Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish. A Dark Oak finish accentuates the unique grains & pattern of the wood. A solid lacquered finish adds a subtle contrast to the design. Spacious L-shaped tabletop offers ample workspace, ideal for multitasking and large projects. Concealed switchboard keeps the workspace clutter-free. 1 password-protected drawer, 1 shelf and 2 cabinets keep your essentials protected and within reach. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
300	High Back Chair Leather :-Supplying and Placing in Potition high back natural leather chair. High back 360° degre revolving chair , All over size is : 650mm(l)x 480mm(d)x 1300mm(h) , The chair made of full natural leather . it will comes in matte finsih about style type is modren. Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchromult-locking mechanism . Only seat size is 560mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1300mm & minimum height is 1240mm gas lift 60mm telescopic haudraulic,class 4 heavy duty gas lift for seat height adjustment bearing capacity 200kgs . Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
301	Low Back Chair Leather :-Supplying and Placing in Position of low back natural leather chair. Low back 360° degre evolving chair , All over size is : 650mm(l)x 510mm(d)x 1150mm(h) , The chair made of full natural leather . It will comes in matte finsih about style type is modren . Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchro multi locking mechanism . Only seat size is 580mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1150mm & minimum height is 1090mm gas lift 60mm telescopic haudraulic , Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
302	High Back chair Leatherrete :-Supplying and placing in position of high back 360° degre revolving chair All over size is : 590mm(l)x 505mm(d)x 1280mm(h) , the chair made of full leatherette .It will comes in matte black finish finsih in contemporary style . Details :- Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat . Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support . Mechanism : knee tilt mechanism . Only seat size is 505mm(l)x 505mm(d)x 610mm(h) & the back size is 590mm(l)x 710mm(h) Seat maximum height is 610mm & minimum height is 510mm & back height from floor maximum height is 1280mm & minimum height is 1180mm ; Gas lift 100 mm telescopic haudraulic . Base : 650 mm chrome base with smooth castors .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
303	Visitor Chairs :- Supplying and placing in position of fix cantilever chair, All over size is : 610mm(L)x 505mm(D)x 990mm(H) ,The chair made of full leatherette . It will comes in matte black finish in contemporary style . Details : - Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed BWR plywood (IS Grade - 303 for seat and back) .Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam , sign based on symmetrical lumbar support backrest support . Only seat size is 610mm(L)x 505mm(D)x 485mm(H) & the back size is 610mm(L)x 540mm(H) , Base : chrome finish tublar frame of cantilever type . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
304	High back mess Chair :-Supplying and placing in position of high back mesh chair with matte finish . The high back 360° degre revolving chair with all over size is : 640mm(l)x 670mm(d)x 1350mm(h) , It will comes in matte finsih about style type is modren. Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 815mm(h) , seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1350mm & minimum height is 1250mm . Gas lift 100 mm telescopic haudraulic ; base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
305	Midium Back Chair :-Supplying and placing in position of medium back 360° degre revolving chair ,All over size is : 640mm(l)x 670mm(d)x 1100mm(h) , The chair made of full mesh .It will comes in matte finsih about style type is modren. Details :- Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support, Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h) . Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm . Gas lift 100 mm telescopic haudraulic , Base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
306	Work Station with Partition :_ supplying and placing of non sharing single seater workstation of 67mm thk sliding tile base partition of 1200mm height, overall size 1200mm x 600mm x 1200mm that is to be assembled at site. the work top shall have the size 1184mm x 592mm made up of 25mm thick pre- laminated particle board of grade ii type iii of is 12823/latest . of is level with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with polyester powder coating 40p-60p thick . the trims shall have the size 67mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways (l-cover for corner, t-cover for middle section wherever required). the aluminium raceway shall be situated below the worktop with an overall size 116mm(h) x 60mm(d) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft-board (with fabric) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (lan) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots/cut-outs should be given on raceways to fix all electrical and data points. single sided pvc wire manager should be enclosed at table top.adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor.particle board of grade ii of is level. Provision of mobile pedestal with key board tray & CPU trolly.
307	Mess visitor Chair :-Supplying and placing in position of fix cantilever mesh chair with matte finish, All over size is : 605mm(l)x 575mm(d)x 1010mm(h) , It will comes in matte finsih in contemporary style . Details :- Arms : pp fixed padded armrest . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h) , Seat max height is @ 470mm . Fixed cantilever chair with base : chrome plated tublar frame of catilever type .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
308	Two Seaters Sofa :-Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size is 1360mm(l) x760mm(d)x 790mm(h) shall have spring attached and also be padded separately. the seat shall have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience polyurethane foam having density 45kg/m³ in seat and 32kg/m³ in back.there shall be cushion arm provided padded with high resilience polyurethane foam having density 32kg/m³. The complete structure shall be upholsteredwith leatherite tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure shall consist of ms powder coated square pipe having cross-section area 25mm x 25mm with 1.6mm thick the legs shall be made up of powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 490 +/- 510mm(d) x 450 +/- 510mm(h). The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
309	Sofa for Visitor room :--Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W)2120mm X (D)1580mm X (H)920mm. Legs crafted with kiln-dried solid wood in Walnut French polish.Premium velvet fabric in beige feels soft and sumptuous.Tested with high rub counts, our fabric ensures high abrasion resistance.Soft seat, cushioned backrest and upholstered track arms offer a comfortable seating experience.A sleek leatherette band with 3 side pockets keeps your essentials within reach.3 complementary throw cushions add a layer of comfort while elevating the design.Anti-sag construction offers the right level of support for maximum comfort.Smooth finished edges eliminate moisture seepage, prevent warping and make it last longer.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
310	Sofa for IG Room :- Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W) 3200mm X (D) 3200mm X (H) 860mm.Sofa frame made of Kiln-dried solid wood ensures durability Breathable leatherette upholstery keeps your body cooler for longer Sleek metal legs make the sofa look airy and light 1 Dual USB port for convenient charging Adjustable backrest transforms the sofa into a lounger.Plush cushioned back and seat for comfortable seating Anti-sag construction offers the right level of support for maximum comfort High ground clearance, designed for modern Indian homes.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
311	Centre Table :-Supplying and Placing in Potition of Hopper Solid Wood Coffee Table size (W)1130mm X (D)630mm X (H)410mm. Inspired by the mid-century modern era, the Hopper collection flaunts clean silhouettes with tapered legs. Crafted with solid beech wood, the dark oak finish accentuates the distinctive wood grains. While the clear glass tabletop flaunts the charming wooden accent. The glass tabletop is made with sturdy glass, beautifully bordered by a solid wood frame. Designed for modern Indian homes, it makes a perfect spot to enjoy cozy talks over a cup of coffee. 8 mm Glass Top. Solid Wood Legs.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
312	Storages :-Suppling and fixing in position of customized ( factory made) Back Storage/ Filing unit with Pre laminate partical bord as approved colour of Depth 450 mm of required size ;- L-800mm x D-450mmx H-1800mm all complete as per direction and satisfaction of Engineer-in- charge :- Storage carcase, shelves and shutters shall be 18mm thick and storage backing shall be 9 mm thick Pre laminated partical board of grade ii type iii of is 12823/latest. The gap between 2 shelves should be range from 400 mm(+/-10 mm) as per the direction of EIC. - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature. - Each shutter should be fixed with 3 numbers SS butt hinges, round shape multipurpose lock, SS tower bolt of 100 x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved make.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
313	Table As. Com. :-Supplying and placing in position of Milburn Director\"s Desk with Leatherette Desk Pad size :- (W) 1800mm X (D) 1220mm X (H) 760mm. Table Top Thickness : 80mm. Experience the perfect harmony of artistry and practicality with our sculptural Milburn Collection. Showcasing a rich Walnut finish, its elegant curves and intricate detailing exude timeless sophistication. The movable drawer pedestal and side runner provide ample storage to keep your workspace organized. Designed with a premium leatherette desk pad, this executive desk redefines luxury and functionality for modern professionals. Crafted from premium engineered wood in Walnut finish. Spacious tabletop offers ample workspace, ideal for multitasking and large projects. Gently curved silhouette with intricate moulding and panel design add a statement appeal. A leatherette desk pad offers a smooth and durable surface for writing and daily tasks. The dedicated keyboard tray provides an ergonomic typing position. Elegant metal pulls in Bronze finish elevate the design. A movable pedestal unit features 3 spacious drawers. A side runner features a dedicated CPU shelf, 1 trolley, 1 shelf, 1 drawer and 1 cabinet. Circular cable organisers keep the tabletop clutter-free. Premium PU polish with low chemical emissions ensures healthy indoor air.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
314	Tables For PA :-Supplying and placing in position of L- shaped desk as per image. The primary work surface over all size is 1500mm(L) x 750mm (D) x 750mm(H) with 25mm thick table top made of prelaminated particle board work surface with wenge finish, using hot melt glue to fixing 2mm thick pvc edge banding made of same matte finish. side pannel is made of 25mm thick. Provision of side runner of size is 750mm (L) x 450mm (D) x 760mm (H) . Construction is from right side of side unit top based on fixed pedestal with ss stud of grade 304, on table top pvc groment hole for wire management . Provision of fixed pedestal of size 450mm (L) x 450mm (D) x 650mm (H) per drawer height is @ 136mm, filling drawer height is @ 300mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. Three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
315	D. Commandant:- Supplying and placing in position of Cabin table as per photograph. Table over all size is 1800mm(l)x 900mm(d)x 750mm(h) 50mm thick table top made of prelaminated particle board work surface with classic wenge brown finish 2mm thick pvc edge banding made of same matte finish. side pannel is made of 50mm thick. Provision of side runner of size is 1200mm(l)x 400mm(d)x 760mm(h) ,(ccombination onstruction below table top 1 key board tray in pvc with telescopic channel on right side is movable side runner having 1 openable door with 1 fixed shelve, 1 open box with 1 fixed shelve upper shelve height is @ 320mm below shelve height is @324@ + 3 drawers (2 equal drawers + 1 filling drawer)per drawer height is @ 184mm, filling drawer height is @ 303mm have central lock and handles with castors . Mobile pedestal of size 400mm(l)x 530mm(d)x 671mm(h) ,per drawer height is @ 186mm, filling drawer height is @ 195mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
316	I.G. Room Table :-Supplying and Placing in Position of Primus Tiered L-Shaped Director\"s Desk size :- (W) 2000mm X (D) 1860mm X (H) 750mm. Table Top Thickness 50mm.The Primus Collection embodies the perfect harmony of curvaceous designs and clean-lined forms, blending sophistication with everyday practicality. This tiered L-shaped director’s desk, featuring a striking contrast of dark oak and lacquered beige finishes, makes a bold statement. Thoughtfully designed with a concealed switchboard and versatile storage, it ensures a clutter-free workspace, allowing you to focus on what matters most. Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish.Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish. A Dark Oak finish accentuates the unique grains & pattern of the wood. A solid lacquered finish adds a subtle contrast to the design. Spacious L-shaped tabletop offers ample workspace, ideal for multitasking and large projects. Concealed switchboard keeps the workspace clutter-free. 1 password-protected drawer, 1 shelf and 2 cabinets keep your essentials protected and within reach. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
317	High Back Chair Leather :-Supplying and Placing in Potition high back natural leather chair. High back 360° degre revolving chair , All over size is : 650mm(l)x 480mm(d)x 1300mm(h) , The chair made of full natural leather . it will comes in matte finsih about style type is modren. Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchromult-locking mechanism . Only seat size is 560mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1300mm & minimum height is 1240mm gas lift 60mm telescopic haudraulic,class 4 heavy duty gas lift for seat height adjustment bearing capacity 200kgs . Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
318	Low Back Chair Leather :-Supplying and Placing in Position of low back natural leather chair. Low back 360° degre evolving chair , All over size is : 650mm(l)x 510mm(d)x 1150mm(h) , The chair made of full natural leather . It will comes in matte finsih about style type is modren . Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchro multi locking mechanism . Only seat size is 580mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1150mm & minimum height is 1090mm gas lift 60mm telescopic haudraulic , Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
319	High Back chair Leatherrete :-Supplying and placing in position of high back 360° degre revolving chair All over size is : 590mm(l)x 505mm(d)x 1280mm(h) , the chair made of full leatherette .It will comes in matte black finish finsih in contemporary style . Details :- Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat . Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support . Mechanism : knee tilt mechanism . Only seat size is 505mm(l)x 505mm(d)x 610mm(h) & the back size is 590mm(l)x 710mm(h) Seat maximum height is 610mm & minimum height is 510mm & back height from floor maximum height is 1280mm & minimum height is 1180mm ; Gas lift 100 mm telescopic haudraulic . Base : 650 mm chrome base with smooth castors .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
320	Visitor Chairs :- Supplying and placing in position of fix cantilever chair, All over size is : 610mm(L)x 505mm(D)x 990mm(H) ,The chair made of full leatherette . It will comes in matte black finish in contemporary style . Details : - Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed BWR plywood (IS Grade - 303 for seat and back) .Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam , sign based on symmetrical lumbar support backrest support . Only seat size is 610mm(L)x 505mm(D)x 485mm(H) & the back size is 610mm(L)x 540mm(H) , Base : chrome finish tublar frame of cantilever type . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
321	High back mess Chair :-Supplying and placing in position of high back mesh chair with matte finish . The high back 360° degre revolving chair with all over size is : 640mm(l)x 670mm(d)x 1350mm(h) , It will comes in matte finsih about style type is modren. Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 815mm(h) , seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1350mm & minimum height is 1250mm . Gas lift 100 mm telescopic haudraulic ; base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
322	Midium Back Chair :-Supplying and placing in position of medium back 360° degre revolving chair ,All over size is : 640mm(l)x 670mm(d)x 1100mm(h) , The chair made of full mesh .It will comes in matte finsih about style type is modren. Details :- Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support, Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h) . Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm . Gas lift 100 mm telescopic haudraulic , Base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
323	Work Station with Partition :_ supplying and placing of non sharing single seater workstation of 67mm thk sliding tile base partition of 1200mm height, overall size 1200mm x 600mm x 1200mm that is to be assembled at site. the work top shall have the size 1184mm x 592mm made up of 25mm thick pre- laminated particle board of grade ii type iii of is 12823/latest . of is level with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with polyester powder coating 40p-60p thick . the trims shall have the size 67mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways (l-cover for corner, t-cover for middle section wherever required). the aluminium raceway shall be situated below the worktop with an overall size 116mm(h) x 60mm(d) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft-board (with fabric) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (lan) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots/cut-outs should be given on raceways to fix all electrical and data points. single sided pvc wire manager should be enclosed at table top.adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor.particle board of grade ii of is level. Provision of mobile pedestal with key board tray & CPU trolly.
324	Mess visitor Chair :-Supplying and placing in position of fix cantilever mesh chair with matte finish, All over size is : 605mm(l)x 575mm(d)x 1010mm(h) , It will comes in matte finsih in contemporary style . Details :- Arms : pp fixed padded armrest . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h) , Seat max height is @ 470mm . Fixed cantilever chair with base : chrome plated tublar frame of catilever type .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
325	Sofa for Visitor room :--Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W)2120mm X (D)1580mm X (H)920mm. Legs crafted with kiln-dried solid wood in Walnut French polish.Premium velvet fabric in beige feels soft and sumptuous.Tested with high rub counts, our fabric ensures high abrasion resistance.Soft seat, cushioned backrest and upholstered track arms offer a comfortable seating experience.A sleek leatherette band with 3 side pockets keeps your essentials within reach.3 complementary throw cushions add a layer of comfort while elevating the design.Anti-sag construction offers the right level of support for maximum comfort.Smooth finished edges eliminate moisture seepage, prevent warping and make it last longer.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
326	Sofa for IG Room :- Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W) 3200mm X (D) 3200mm X (H) 860mm.Sofa frame made of Kiln-dried solid wood ensures durability Breathable leatherette upholstery keeps your body cooler for longer Sleek metal legs make the sofa look airy and light 1 Dual USB port for convenient charging Adjustable backrest transforms the sofa into a lounger.Plush cushioned back and seat for comfortable seating Anti-sag construction offers the right level of support for maximum comfort High ground clearance, designed for modern Indian homes.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
327	Centre Table :-Supplying and Placing in Potition of Hopper Solid Wood Coffee Table size (W)1130mm X (D)630mm X (H)410mm. Inspired by the mid-century modern era, the Hopper collection flaunts clean silhouettes with tapered legs. Crafted with solid beech wood, the dark oak finish accentuates the distinctive wood grains. While the clear glass tabletop flaunts the charming wooden accent. The glass tabletop is made with sturdy glass, beautifully bordered by a solid wood frame. Designed for modern Indian homes, it makes a perfect spot to enjoy cozy talks over a cup of coffee. 8 mm Glass Top. Solid Wood Legs.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
328	Storages :-Suppling and fixing in position of customized ( factory made) Back Storage/ Filing unit with Pre laminate partical bord as approved colour of Depth 450 mm of required size ;- L-800mm x D-450mmx H-1800mm all complete as per direction and satisfaction of Engineer-in- charge :- Storage carcase, shelves and shutters shall be 18mm thick and storage backing shall be 9 mm thick Pre laminated partical board of grade ii type iii of is 12823/latest. The gap between 2 shelves should be range from 400 mm(+/-10 mm) as per the direction of EIC. - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature. - Each shutter should be fixed with 3 numbers SS butt hinges, round shape multipurpose lock, SS tower bolt of 100 x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved make.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
329	Tables For PA :-Supplying and placing in position of L- shaped desk as per image. The primary work surface over all size is 1500mm(L) x 750mm (D) x 750mm(H) with 25mm thick table top made of prelaminated particle board work surface with wenge finish, using hot melt glue to fixing 2mm thick pvc edge banding made of same matte finish. side pannel is made of 25mm thick. Provision of side runner of size is 750mm (L) x 450mm (D) x 760mm (H) . Construction is from right side of side unit top based on fixed pedestal with ss stud of grade 304, on table top pvc groment hole for wire management . Provision of fixed pedestal of size 450mm (L) x 450mm (D) x 650mm (H) per drawer height is @ 136mm, filling drawer height is @ 300mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. Three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
330	D. Commandant:- Supplying and placing in position of Cabin table as per photograph. Table over all size is 1800mm(l)x 900mm(d)x 750mm(h) 50mm thick table top made of prelaminated particle board work surface with classic wenge brown finish 2mm thick pvc edge banding made of same matte finish. side pannel is made of 50mm thick. Provision of side runner of size is 1200mm(l)x 400mm(d)x 760mm(h) ,(ccombination onstruction below table top 1 key board tray in pvc with telescopic channel on right side is movable side runner having 1 openable door with 1 fixed shelve, 1 open box with 1 fixed shelve upper shelve height is @ 320mm below shelve height is @324@ + 3 drawers (2 equal drawers + 1 filling drawer)per drawer height is @ 184mm, filling drawer height is @ 303mm have central lock and handles with castors . Mobile pedestal of size 400mm(l)x 530mm(d)x 671mm(h) ,per drawer height is @ 186mm, filling drawer height is @ 195mm having (2 equal drawers + 1 filling drawer) in provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
331	I.G. Room Table :-Supplying and Placing in Position of Primus Tiered L-Shaped Director\"s Desk size :- (W) 2000mm X (D) 1860mm X (H) 750mm. Table Top Thickness 50mm.The Primus Collection embodies the perfect harmony of curvaceous designs and clean-lined forms, blending sophistication with everyday practicality. This tiered L-shaped director’s desk, featuring a striking contrast of dark oak and lacquered beige finishes, makes a bold statement. Thoughtfully designed with a concealed switchboard and versatile storage, it ensures a clutter-free workspace, allowing you to focus on what matters most. Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish.Masterfully crafted of premium engineered wood in Dark Oak and lacquered finish. A Dark Oak finish accentuates the unique grains & pattern of the wood. A solid lacquered finish adds a subtle contrast to the design. Spacious L-shaped tabletop offers ample workspace, ideal for multitasking and large projects. Concealed switchboard keeps the workspace clutter-free. 1 password-protected drawer, 1 shelf and 2 cabinets keep your essentials protected and within reach. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
332	High Back Chair Leather :-Supplying and Placing in Potition high back natural leather chair. High back 360° degre revolving chair , All over size is : 650mm(l)x 480mm(d)x 1300mm(h) , The chair made of full natural leather . it will comes in matte finsih about style type is modren. Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchromult-locking mechanism . Only seat size is 560mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1300mm & minimum height is 1240mm gas lift 60mm telescopic haudraulic,class 4 heavy duty gas lift for seat height adjustment bearing capacity 200kgs . Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
333	Low Back Chair Leather :-Supplying and Placing in Position of low back natural leather chair. Low back 360° degre evolving chair , All over size is : 650mm(l)x 510mm(d)x 1150mm(h) , The chair made of full natural leather . It will comes in matte finsih about style type is modren . Details : Arms : chrome finish arm rest covering with natural leather pad. Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support. Mechanism : synchro multi locking mechanism . Only seat size is 580mm(l)x 610mm(h) & the back size is 590mm(l)x 660mm(h) . Seat maximum height is 610mm & minimum height is 540mm & back height from floor maximum height is 1150mm & minimum height is 1090mm gas lift 60mm telescopic haudraulic , Base : 650 mm strong chrome swivel base with 55 mm castors (pressure bearing 1136 kg ) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
334	High Back chair Leatherrete :-Supplying and placing in position of high back 360° degre revolving chair All over size is : 590mm(l)x 505mm(d)x 1280mm(h) , the chair made of full leatherette .It will comes in matte black finish finsih in contemporary style . Details :- Arms : chrome finish arms with pu padding . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat . Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support . Mechanism : knee tilt mechanism . Only seat size is 505mm(l)x 505mm(d)x 610mm(h) & the back size is 590mm(l)x 710mm(h) Seat maximum height is 610mm & minimum height is 510mm & back height from floor maximum height is 1280mm & minimum height is 1180mm ; Gas lift 100 mm telescopic haudraulic . Base : 650 mm chrome base with smooth castors .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
335	Midium Back Chair :-Supplying and placing in position of medium back 360° degre revolving chair ,All over size is : 640mm(l)x 670mm(d)x 1100mm(h) , The chair made of full mesh .It will comes in matte finsih about style type is modren. Details :- Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support, Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h) . Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm . Gas lift 100 mm telescopic haudraulic , Base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
336	Work Station with Partition :_ supplying and placing of non sharing single seater workstation of 67mm thk sliding tile base partition of 1200mm height, overall size 1200mm x 600mm x 1200mm that is to be assembled at site. the work top shall have the size 1184mm x 592mm made up of 25mm thick pre- laminated particle board of grade ii type iii of is 12823/latest . of is level with approved laminate and finish as per approved shade. the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with polyester powder coating 40p-60p thick . the trims shall have the size 67mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways (l-cover for corner, t-cover for middle section wherever required). the aluminium raceway shall be situated below the worktop with an overall size 116mm(h) x 60mm(d) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. there shall be soft-board (with fabric) and marker board provided at front of the user. laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. the partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (lan) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots/cut-outs should be given on raceways to fix all electrical and data points. single sided pvc wire manager should be enclosed at table top.adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor.particle board of grade ii of is level. Provision of mobile pedestal with key board tray & CPU trolly.
337	Mess visitor Chair :-Supplying and placing in position of fix cantilever mesh chair with matte finish, All over size is : 605mm(l)x 575mm(d)x 1010mm(h) , It will comes in matte finsih in contemporary style . Details :- Arms : pp fixed padded armrest . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h) , Seat max height is @ 470mm . Fixed cantilever chair with base : chrome plated tublar frame of catilever type .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
338	Sofa for Visitor room :--Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W)2120mm X (D)1580mm X (H)920mm. Legs crafted with kiln-dried solid wood in Walnut French polish.Premium velvet fabric in beige feels soft and sumptuous.Tested with high rub counts, our fabric ensures high abrasion resistance.Soft seat, cushioned backrest and upholstered track arms offer a comfortable seating experience.A sleek leatherette band with 3 side pockets keeps your essentials within reach.3 complementary throw cushions add a layer of comfort while elevating the design.Anti-sag construction offers the right level of support for maximum comfort.Smooth finished edges eliminate moisture seepage, prevent warping and make it last longer.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
339	Sofa for IG Room :- Supplying and placing L-Shape sofa as per photograph. Sofa Size :- (W) 3200mm X (D) 3200mm X (H) 860mm.Sofa frame made of Kiln-dried solid wood ensures durability Breathable leatherette upholstery keeps your body cooler for longer Sleek metal legs make the sofa look airy and light 1 Dual USB port for convenient charging Adjustable backrest transforms the sofa into a lounger.Plush cushioned back and seat for comfortable seating Anti-sag construction offers the right level of support for maximum comfort High ground clearance, designed for modern Indian homes.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
340	Centre Table :-Supplying and Placing in Potition of Hopper Solid Wood Coffee Table size (W)1130mm X (D)630mm X (H)410mm. Inspired by the mid-century modern era, the Hopper collection flaunts clean silhouettes with tapered legs. Crafted with solid beech wood, the dark oak finish accentuates the distinctive wood grains. While the clear glass tabletop flaunts the charming wooden accent. The glass tabletop is made with sturdy glass, beautifully bordered by a solid wood frame. Designed for modern Indian homes, it makes a perfect spot to enjoy cozy talks over a cup of coffee. 8 mm Glass Top. Solid Wood Legs.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
341	Storages :-Suppling and fixing in position of customized ( factory made) Back Storage/ Filing unit with Pre laminate partical bord as approved colour of Depth 450 mm of required size ;- L-800mm x D-450mmx H-1800mm all complete as per direction and satisfaction of Engineer-in- charge :- Storage carcase, shelves and shutters shall be 18mm thick and storage backing shall be 9 mm thick Pre laminated partical board of grade ii type iii of is 12823/latest. The gap between 2 shelves should be range from 400 mm(+/-10 mm) as per the direction of EIC. - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot melt glue at hot temperature. - Each shutter should be fixed with 3 numbers SS butt hinges, round shape multipurpose lock, SS tower bolt of 100 x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved make.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
342	Two Seaters Sofa :-Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size is 1360mm(l) x760mm(d)x 790mm(h) shall have spring attached and also be padded separately. the seat shall have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience polyurethane foam having density 45kg/m³ in seat and 32kg/m³ in back.there shall be cushion arm provided padded with high resilience polyurethane foam having density 32kg/m³. The complete structure shall be upholsteredwith leatherite tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure shall consist of ms powder coated square pipe having cross-section area 25mm x 25mm with 1.6mm thick the legs shall be made up of powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 490 +/- 510mm(d) x 450 +/- 510mm(h). The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
343	Dining Table Circluar 4 seaters :-Supplying and placing position of 4str dining table set as per photograph. Tale Size :- (W)900mm X (D)900mm X (H)750mm. Chair Size :-(W)360mm X (D)360mm X (H)705mm.Smart stowaway design lets you slot chairs under the table.Tabletop made of premium painted glass in black and purple.Table and chair legs crafted of high-quality metal.Premium leatherette upholstery in black and purple accentuate the monochrome look.Chairs feature barrel-curved back for an enveloping comfort.Suitable for compact urban spaces.Ample leg space lets you stretch your legs for added comfort.. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
344	Supplying & Placining position of u - shape modern design conference table & in between u shape table over all size:- L-9300mm x D-1950mm x H-750mm. is 1350mm(l)x 600mm(d)x 750mm(h) (12 nos) , Size ;- L-750mm x D-600mm x H-750mm (2 NOs) & Corner both side 600 x 600x 750 (2 Sets). table top made of 25mm thick which give more surface area for work ,machine made modular furniture made prelaminated particle board of grade ii type iii of is 12823/latest, construction provision of conference tabletop supported with 18mm thick side pannels in brown-black oak colour made by prelaminated particle board and below the top 18mm thick prelam particle board modesty panel.our work surface furniture is finished with exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade,fixed with hot melt glue. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
345	High back mess Chair :-Supplying and placing in position of high back mesh chair with matte finish . The high back 360° degre revolving chair with all over size is : 640mm(l)x 670mm(d)x 1350mm(h) , It will comes in matte finsih about style type is modren. Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 815mm(h) , seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1350mm & minimum height is 1250mm . Gas lift 100 mm telescopic haudraulic ; base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
346	Midium Back Chair :-Supplying and placing in position of medium back 360° degre revolving chair ,All over size is : 640mm(l)x 670mm(d)x 1100mm(h) , The chair made of full mesh .It will comes in matte finsih about style type is modren. Details :- Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support, Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h) . Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm . Gas lift 100 mm telescopic haudraulic , Base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Chandigarh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Admin Block At Western Command Hqr Chandigarh., Chandigarh-Chandigarh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Admin Block At Western Command Hqr Chandigarh., Chandigarh-Chandigarh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us