|
| 1 | Sub Heading 1 |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil Total=1’8”x1’8”x2’6”x6=41.35cft>1.171cum |
| 3 | Providing and laying in position specified grade of reinforced concrete, excluding the cost of centring, shuttering, finishing ,and reinforcement – mix 1::1.5:3 (1 cement: 1.5 coarse sand(zone-III)derived from natural source :3 graded stone aggregate 20mm nominal size derived from natural source)Base =21.09cft+stniffner =53.73cft+Tie beam=38.80cft +band 2x19.4 cft =114.32cft>3.23 cum |
| 4 | Reinforcement( TMT C-500) for RCC worksincluding straitening, cutting, bending, binding, placing in position T 8=66kg.T10-54KG,T6-50kg=170kg |
| 5 | Providing &fixing , centering & shuttering for all RCC works with props etc.and its removal.Total = 24.90sqm |
| 6 | Dry brick edge flooring in required pattern with of bricks of class designation 7.5 on a bed of 12mm mud mortar including filling joints with Ganga sand Total Area=200+49.8=249.8sft >23.21sqm |
| 7 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate Total Area=200sft>18.58sqm |
| 8 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)[(60x9.5+1/2x20x6”x2) -(24.5+12)] x0.83= 443.22cft >12.56cum |
| 9 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) Total= 100-24.5=75.5sft>7.01sqm |
| 10 | 12mm cement plaster of mix.1:6 (1 cement: 6fine sand)TotalArea= inside 1275+outside 667=1942sft>180.48sqm |
| 11 | Steel work for making of door of single section ,cutting welding,hosting and fiittngwith a coat of primer 3.5’x7’ >49kg |
| 12 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes of 2”&1”hollow pipe Total 96 kg weight |
| 13 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.Total area=(24’1”x12’8”)=304.85sft~28.33qm |
| 14 | Goods and Service Tax |
