|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 2 | Disposal of excavated earth lead upto 5.0 Km by mechanical transport. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand (zone-iii) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 7 | Randam Rabble(RR) Boulderstone masonary in 1:6 cement sand mortar with Boulderstone in R/wall, B/wall,and Parapets worksi/c all costof material, labours and T&P etc. for proper completion of the work. |
| 8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 9 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 10 | Steel work welded in built up sections/framed work,including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, |
| 11 | Excluding of Steel. |
| 12 | Steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more. |
| 13 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 14 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineerin-Charge.With cement mortar 1:4 (1 cement : 4 fine sand) |
| 15 | 15 mm thick cement sand mortar in 1:3 with water proofing compound and moorga jali i/c of all materials, labours & T&P etc required for proper completion. |
| 16 | Providing and fixing ISI marked, IS : 1341, M.S. heavy weight bright finished butt hinges with necessary screws etc. complete : 9.56.1 125x90x4.00 mm |
| 17 | Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel chromium plating grade 1 as per IS: 1068 and fixing with necessary screws etc., complete.Overall width 35 mm |
| 18 | centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete |
| 19 | Coulmns,Pillers,Abutments,Posts,Struts etc. |
| 20 | Lintels,beams,plinth beams,girder and cantilever etc. |
| 21 | Suspended floors, roofs, landings, balconies and access platform |
| 22 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 23 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutterswith ISI marked M.S. pressed butt hinges bright finished of required sizeSecond class teak wood Kiln seasoned selected class of sheesham wood |
| 24 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood35 mm thick |
| 25 | P/F 4 mm thick glass pans in window / door with putty / beading including all cost of materials, labours & T&P etc. required for proper completion of work. |
| 26 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 27 | P/F GPI Plain sheet including cost of materials, labours & T&P etc. (0.63 mm thick) |
| 28 | S/F Welded wire mesh (30 X 30 X 3 mm) including cutting welding where necessary and also including supply of materials, labours & T&P etc. required for proper completion of the work. |
| 29 | without material |
| 30 | S/F Sal wood wrought framed fiexd work as in choukhat including supply of all materials, labours T&P etc required for proper completion of work. |
| 31 | S/F 6 mm plywood in ceiling,partionincluding supply of all materials, labours & T&P etc. |
| 32 | S/F 6 mm plywood in partitionincluding supply of all materials, labours & T&P etc. |
| 33 | S/F 12 mm plyboar inpartion including supply of all materials, labours & T&P etc. |
| 34 | Providing and fixing flat pressed three layer particle or graded plain wood board medium density exterior grade (Grade I) FPT-1, conforming and marked to IS : 3087 to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately):18 mm thick |
| 35 | S/F oxidised M.S pressed fitting with necessary screw etc. complete. |
| 36 | (A) Tower Bolt 150 X 10 mm |
| 37 | B ) Tower Bolt 100 X 10 mm |
| 38 | (C) Handles 125mm. |
| 39 | (D) Handles 100 mm. |
| 40 | E ) Sliding Door Bolt 250 X 16 mm. |
| 41 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 42 | Providing and applying white cement based putty single coat of average thickness 1 mm, of approved brand and manufacturer, |
| 43 | White washing with lime to give an even shade on old surface (one or more coat) |
| 44 | Oil bond distemper on old surface with approved make and manufacture and required shade on old work to given an even shade. |
| 45 | (A) Two coat on new work. |
| 46 | (B) One coat on old work. |
| 47 | (c ) two coat on old work |
| 48 | Finishing wall with water proofing cement paint of approved brand and manufacture on old work to given an even shade (SNOWCEM) |
| 49 | (a) One Coat on old work. |
| 50 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 51 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work |
| 52 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture (with primer) |
| 53 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work (without primer) |
| 54 | Water proofing on roof surface by using damp proof material with two coat i/c supply of all material, labour T&P etc. |
| 55 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 56 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 57 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 58 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White |
| 59 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 60 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 61 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 62 | (a) 75 mm diameter |
| 63 | (b) 110 mm diameter |
| 64 | (c) 160 mm diameter |
| 65 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° |
| 66 | (a)75 mm bend |
| 67 | (b) 110 mm bend |
| 68 | (c) 160 mm bend |
| 69 | Single tee without door |
| 70 | (a) 75x75x75 mm |
| 71 | (b) 110x110x110 mm |
| 72 | S/F of PVCCollerincluding all cost of materials, labours & T&P etc. requiredfor proper completion of work. |
| 73 | (a) 75 mm dia |
| 74 | (b) 110 mm dia |
| 75 | (c) 160 mm dia |
| 76 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 77 | (a) 75 mm |
| 78 | (b) 110 mm |
| 79 | P/F GI Pipe complete with GI fitting & clamps including cutting & making good wall. |
| 80 | (a)15 mm dia pipe. |
| 81 | (b)20 mm dia pipe. |
| 82 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. |
| 83 | (A) 20 mm nominal dia Pipes |
| 84 | (B) 25 mm nominal dia Pipes |
| 85 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 86 | (A) S/F PVC Nahani trap including all cost of materials, labours & T7P etc. |
| 87 | S/F CP grating i/c all cost of materials, laboursand T&P rquired for proper completion of the work. |
| 88 | S/F 15mm CP short body/bib cock& Stop cock including all cost of materials, labours & T&P etc. required for proper completion of the work. |
| 89 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore |
| 90 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore |
| 91 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore |
| 92 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. |
| 93 | 15 mm nominal bore |
| 94 | 20 mm nominal bore |
| 95 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm lenth15 mm nominal bore |
| 96 | S/F of CP,Towal rail 750x20 mm etc.i/c all cost of materials,labours,T&P etc. |
| 97 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe32 mm dia |
| 98 | Const. of brick masonary Man hole chamber in 1:6 mix RCC top slab with 1: 1.5:3 mix foundation conc. 1:5:10 mix 12.5 mm inside plaster in mix 1:3 finished with a floating coat of neat cement & making chanel in cement conc. 1:2:4 mix finished with a floating coat of neat cement etc. with class-100 bricks (inner size 90 X 80 cm & 45 cm deep including cover 600 X 600mm inner size total weight of cover & frame to be not less than 38 Kg. |
| 99 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) ith hinged cover fixed in reinforced cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coars sand : 3 graded stone aggregate 20 mm nominal size), including necessary xcavation,foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick,finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 100 | Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer-in-Charge |
| 101 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,machine cut for kitchen platforms, vanity counters, window sills, facias and imilar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with whiteement, mixed with matching pigment,epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab over 0.50 sqm |
| 102 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever requiredKitchen sink without drain board 610x510 mm bowl depth 200 mm |
| 103 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer)of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 white cement and matching pigment etc., complete.Coarse sand),Jointing with grey cement slurry3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 104 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey matching shade complete cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 105 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 106 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction ofEngineer-in-charge. |
| 107 | (a)Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers lled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces)0.63 mm thick with zinc coating not less than 275 gm/ m² |
| 108 | (b)excluding material |
| 109 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia (heavy type) |
| 110 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick |
| 111 | Providing and fixingalluminium door stopper with twin rubber etc. |
| 112 | S/F of barbet wire(gi)i/c all cost of materials, labours & T & P etc. requiredfor proper completion of work. |
| 113 | S/F ofglass shelf etc.i/c all cost of materials,labours,T&P etc. |
| 114 | S/Fixing of 20mm brass Gate Valve with CI wheel i/c all cost of materials,labours,T&P etc. |
| 115 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 116 | 15 mm nominal bore |
| 117 | 20 mm nominal bore |
| 118 | Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/ 25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). |
| 119 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 120 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 15.2.1 Nominal concrete 1:3:6 or richer mix (i/cquivalent design mix) |
| 121 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - incharge. |
| 122 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 123 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 124 | Dismantling of cement concrete floor including base concrete and including stacking of dismantal materials as directed by Engr-in-charge within a distance of 60 Mtrs. |
| 125 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 126 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below |
| 127 | Dismantling of CGI sheet roof / wooden celling walls or partion including purlin, batten, vertical support and including stacking of dismantaled materials within 60 M distance as directed by Engr-in-charge. |
| 128 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 129 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. |
| 130 | Disconnecting damaged verhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineerin-charge. |
| 131 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. |
| 132 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 133 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap eading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) |
| 134 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket equired (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 135 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness |
| 136 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) sqm 1325.55 |
