|
| 1 | EARTHWORK: Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables, etc (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift up to 1.5m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres, all kinds of soil. |
| 2 | STONE SOLING: Providing and laying of hand packed stone soling (size 150 mm-230mm), before laying of mud mat, compacted, consolidated, rammed and filling the voids with fine sand - all complete incl carriage upto site of work with all head loads. |
| 3 | MUDMAT: Cast-in-situ of concrete work of nominal mix concrete M7.5 grade (1:4:8) nominal maximum size of stone aggregate 40mm volumetric batching in foundation trenches and ground floor, including curing but excluding formwork costs. |
| 4 | MASS CONCRETE: Providing and laying mass concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in Below Ground and Above Grouns Plinth retaining walls, (any thickness) including attached pilasters, including curing but excluding the cost of centring, shuttering and finishing with. |
| 5 | CAST-IN-STU DESIGN MIX M25: Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,incluyding pumping of concrete to site laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportiond as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable seperately all works Below Plinth Levl / Above Plinth Level upto level V (AGL/BGL).. |
| 6 | UPTO PLINTH LEVEL |
| 7 | ABOVE PLINTH LEVEL |
| 8 | FORM WORK: Centering and shuttering including strutting, propping etc. and removal of formwork from the site, for all works from foundations, to roof level. |
| 9 | BELOW PLINTH LEVEL Foundation, Raft |
| 10 | BELOW Ground level Landing sides, Stairs, Short columns, Plinth Beam & Above ground level stair |
| 11 | ABOVE PLINTH LEVEL Slabs, Slab beams, sill band, lintle band, columns and slab edges |
| 12 | PLINTH FILLING: Supplying and filling in plinth with GSB/ Second class sand under floors including, watering, ramming, consolidating and dressing complete. |
| 13 | BACK FILLING: Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 14 | STEEL REINFORCEMENT: Steel reinforcement for R.C.C. works including straightening, cutting, bending, placing in position and binding -all complete from foundation to roof level of Thermo-Mechanically Treated bars of grade Fe-500D or higher. |
| 15 | EXPANSION JOINT |
| 16 | FLOOR |
| 17 | WALLS |
| 18 | STRUCTURAL STEEL:Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer all complete. plates, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer also included. |
| 19 | ANCHOR BOLTS: Providing and fixing bolts including nuts, washers complete job. |
| 20 | Providing and laying Autoclaved Aerated Cement blocks masonry with 100 mm thick AAC blocks in superstructure above plinth level upto floor V level in cement mortar 1:4 (1 Cement : 4 coarse sand ) and curing complete. The rate includes providing and placing in position 2 nos. 6 mm dia M.S bars at every third course of masonry work |
| 21 | Brick masonry with FPS bricks of class designation 75 in super structure up to floor V level in cement mortar 1:6 (1cement: 6 cement coarse sand). complete in all respects |
| 22 | Half brick masonry in 1 cement 4 finesand mortar, with first class (100A) bricks, in superstructure up to floor V level complete in all respects |
| 23 | Providing wood work in frames for doors, windows, clerestory windows and other frames Wrought framed and fixed in positions (First class kail wood ). |
| 24 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made .. ( Complete as per Sample approved by E.I.C) {FINESTA MAKE} |
| 25 | Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) |
| 26 | Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) |
| 27 | Providing and fixing 35 mm thick paneled door shutters (Ist class local Kail Wood). With 25-30 mm thick Ornamental Kail Wood panels including necessary stainless Steel Butt hinges /screws etc. Design of shutter and panels as per the instructions of Engineer incharge complete in all respects. |
| 28 | Providing and fixing paneling or paneling/ glazing in paneled or paneled & glazed shutters for windows and clerestory windows (Area of opening for panel inserts excluding portion in side grooves or rebates to be measured). Paneling for paneled or paneled glazed shutters.(Fixed Glasses 3.5 mm thick in Glazed Portions)3.5 mm thick glass pane Float glass panes (weighing not less than 10 kg/sqm) including cost of teak wood beadings of required size complete.(For Fixed Glasses in Glazed Portions) |
| 29 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 30 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : ( 35mm thick shutters with first class kail wood.) |
| 31 | Providing and fixing 15 mm thick T&G planks made of imported wood (New zealand pine or equivalent) on wood work in false ceiling, wall/wall partitions sawn and put up in position ( budloo wood Ceiling Joists of 50 mm x 65 mm in sections placed @ 600 mm C/C both ways or as required at site). including cost of necessary Cornices/beadings of Kail wood of required sizes (wherever required) / adhesive & cost of nails etc. all complete upto floor 5 level as per the directions of Consultant / Engineer-in-charge .(For panelling /Ceilings/Soffits etc.) |
| 32 | Providing and fixing planed eves boarding of with necessary grooves and chamfer as per detailed drawing / as per the directions of Engineer Incharge - 2nd class kail wood (300x40 mm (nominal size) |
| 33 | Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand:4 graded stone agg.) finished with a floating coat of neat cement including cement slurry but excl. the cost of nosing of steps etc. complete. (50mm thick with 20mm nominal size crushed stone aggregate) |
| 34 | Providing & fixing glass strips in joints of terrazzo/cement conc. floating (40mm wide and 4mm thick). |
| 35 | Providing and fixing Track deck crill make or equivalent H.I. rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anti-capillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness ) |
| 36 | Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges/ valleys plain (500 - 600mm) |
| 37 | Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building.With resin bonded fiber glass wool with density 24 kg/cum |
| 38 | Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. (With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles. ) |
| 39 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(600 x 1200 mmm) (Complete as per Sample approved by E.I.C ) |
| 40 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms/flooring, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels .(Granite of any colour or shade (Area of slab upto 0.5 sqm) 18 mm thick (Complete as per Sample approved by E.I.C ) |
| 41 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding tubes channels, plates etc. including welding ,grinding, buffing, polishingand making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slabwith suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).(Complete as per Sample approved by E.I.C ) |
| 42 | Extra for Providing & fixing of stainless steel navel post (Ornamental) including top ball of 304 grade of required height duly anchored to floor with dash fasteners (Complete as per Sample approved by E.I.C ) |
| 43 | 12 mm thick cement plaster on rough side of single or half brick wall in (1 cement: 6 fine sand mix). Upto floor V level complete in all respects |
| 44 | 18 mm Cement plaster in two coats under layer 12mm thick cement plaster 1 : 5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1 : 6 (1 cement : 6 fine sand) including making necessary grooves/chamfers etc.complete as per the design and directions of consultant. |
| 45 | 6 mm cement plaster to ceiling ,soffits etc of mix 1 : 3 (1 cement : 3 fine sand) . Upto floor V level complete in all respects |
| 46 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.. (2mm thick) |
| 47 | Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work and wooden based surfaces complete.(including cost of all material, leads, lifts and carriages etc. upto site of work complete). |
| 48 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.( Two or more coats on new work) |
| 49 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work including one coat of water thinnable cement primer. |
| 50 | Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm |
| 51 | Pointing brick masonary walls with lime Surkhi to make grooves limely red including grinding and polishing /finishing etc the brick Surface (to give a heritage look) , making the surfaces even and smooth by way of removing all foreign mateials/drpos of mortar etc including all scaffolding /necessary form works etc. upto desired height .including cost of material and labour all complete as per the directions of site Engineer |
| 52 | French spirit polishing, Two or more coats on new works including a coat of wood filler complete in all respects. |
| 53 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: - Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(A per the specifications and as per site Requirments complete in all respects,) |
| 54 | Providing & Fixing Cupboard 50 to 60 cm deep made from commrcial Plywood 18mm thickalround except back side which shall be 6mm thick, with shutters of 18mm plywood & steel hinges knobes/handels magnetic latch including wood primer and two coats synthetic enamel paint as per given drawing and direction of EIC. Front side of cupboard should be finished with Denmica (Finshed face area to be measured for thepurpose of payment) |
| 55 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 56 | Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer Incharge/ consultant, complete as per the specifications (Brass fittings ) |
| 57 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. |
| 58 | Providing and fixing bright finished brass handles with screws etc. complete (125 mm) |
| 59 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.(Door Locks) |
| 60 | Carriages of materials from source to Site of work by mechanical transport complete as per the site requirements |
| 61 | Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work till complete in all respects. Please Enable Macros to View BoQ information |
