Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level andremovingmaterial from site complete all as specified and directed by Engr-in-charge. (for first floor flooring) |
| 2 | Taking down wooden chowkats or frames with shutters area not exceeding 1.50 Sqm(w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and directed by Engr-in-charge. |
| 3 | Taking down wooden chowkats or frames with shutters area exceeding 1.50 Sqm andnot exceeding 4.00 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and directed by Engr-in-charge. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-charge. |
| 5 | Material & Labour for Non-Skid white Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed incement mortar 1:6 complete all as specified and directed by Engr-in-charge. |
| 6 | Material & Labour for Glazed white ceramic tiles in vertical surface300mm X 600 mm X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to matchincluding 10mm thick cement plaster in ement mortar 1:4 as backing coat on fair faces on stone surface complete all as specified and directed by Engr-in-charge. |
| 7 | Supply andfixingfor machine pressed precast concrete coloured interlocking ( glossy finishing) paver blocks confirming to IS-15658-2006 of 60 mm thickness, M-35 grade asin hardstandingetc.Set & jointed with grey cement and pigment laid over and including 50 mm thick screed or bedding layer of sand, complete all as specified and directed by Engr-in-charge. |
| 8 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons,laid dry and pointed in any mortar etc. complete all as specified and directed by Engr-in-charge. (For Ground floor only) |
| 9 | Material and labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of size not less than 55 cm x 55 cm in flooring and 120 cm x 25 cm in treads) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including half round edge moulding, over and including cement screed bed 15 mm thick in cement mortar (1:6) baseincluding rubbing and mirror polishing, and half nose moulding (bull nosing) etc, complete all as specified and directed by Engr-in-charge. |
| 10 | Material & Labour for machine cut Prepolished Kota stone slab 20-25 mm thick (of length not less than 55 cm in skirting and 120 cm in risers) laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in vertical surfaces such as skirting and risers over and including 10mm thick plaster in cement mortar (1:4) onbrick work or concrete surfaces, complete all as specified and directed by Engr-in-charges. |
| 11 | Material & Labour for Granite work (Jet/Telephonic Black) 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, counter basins, urinal partitions etc. and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types and including 15mm thick screed bed in CM 1:6set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces and half nose moulding (bull nosing) etc, complete all as specified and directed by Engr-in-charges. |
| 12 | Material and Labour for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in sub base/levelling coarse and finished the top surface even and fair complete all as specified and directed by Engr-in-charges. |
| 13 | Material & Labour for brickwork with old size fly ash bricks straight or curved on plan exc. 6 M mean radius built in CM 1:6, including of demolition brick work/stone masonry of complete all as specified and directed by Engr-in-charges. |
| 14 | Material and Labour for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base/mass concrete and finished the top surface even and fair complete all as specified and directed by Engr-in-charges. |
| 15 | Material & Labour for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished complete. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection. complete all as specified and directed by Engr-in-charges. |
| 16 | Supplyand fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125mm(moulded) having Double rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by \"Rajshri/Echon or Eq\" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company. complete all as specified and directed by Engr-in-charges. |
| 17 | S&FFactory made single extruded WPC (wood polymer composite) soild decorative type Moulded door shutter of size 30 mm thick material comprising of virgin PVC polymer of K-Value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives(maxiumum toxicity index of 12 for 100 gms)having minimum frame density of 650 Kg/cbm & manufactured by \"Rajshri/Echon or Eq\" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 1800N(face) & 900 N(edge),) Minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter& fixed with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed by Engr-in-charges. |
| 18 | Supply and fixing IInd class (hollock) hard wood factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed by Engr-in-charges. |
| 19 | Supplyand fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 50 mm x 100 mm(moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by \"Rajshri/Echon or Eq\" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company. complete all as specified and directed by Engr-in-charges. |
| 20 | S&FFactory made single extruded WPC (wood polymer composite) soild decorative type Flush door shutter of size 30 mm thick material comprising of virgin PVC polymer of K-Value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives(maxiumum toxicity index of 12 for 100 gms)having minimum frame density of 650 Kg/cbm & manufactured by \"Rajshri/Echon or Eq\" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 1800N(face) & 900 N(edge),) Minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter& fixed with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed by Engr-in-charges. |
| 21 | Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-charges. |
| 22 | Supply & fixed150 mm long Extruded aluminiumalloy handles, fabricatedtype anodised complete all as specified and directed by Engr-in-charges. |
| 23 | Supply & fixed100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed by Engr-in-charges. |
| 24 | S&F 100 mm long stainless steel butt hinges medium weight with galvanised MS hinge pin etc. complete all as specified and directed by Engr-in-charges. |
| 25 | S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified and directed by Engr-in-charges. |
| 26 | S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber complete all as specified and directed by Engr-in-charges. |
| 27 | Supply & fixedMS helical door spring 300 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats. complete all as specified and directed by Engr-in-charges. |
| 28 | Supply & Fixedin repairs aluminium Hat and coat hooks, solid body, 175mm to 250 mm complete all as specified and directed by Engr-in-charges. |
| 29 | M&L for providing and fixing of window, ventilator fabricated from roll formed sections made of galvanized steel colour coated /powder coated (Base steel as per IS 513 \"D\" quality, Galvanized as per IS 277 with Zinc of 120 grams/Sqm) with total coated thickness of 0.60 mm Paint specifications: Coated Sections should be coated with primer Coat of Epoxy Primer of 5-7 microns thick, finish painted with Polyster paint of 12-16 micorns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyster Powder up to 50-60 microns thick. Dimensions of Sections :Sections for Frame of 72mm x 50mm, Section for Mullion of size 72mm x 50mm, Section for Shutter Frame of size 47mm x 20mm, Section for Frame Glass Beads of 12mm x 12mm, and Section for Fly mesh of 40mm x 20mm. Fixing Details : Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined to the Frame/Mullion using Nylon Cap. Ethyl Propylene Daimine Monomer (EPDM) Gasket should be used all around glass in shutter and fixed galss. Rubber Gasket should be used around Fly mesh to fix in Mesh Shutter. Accesories: Each Glazed shutter should be provided with S.S.Pivot Hignes-01 set, Seccolor Handle & Seccolor Stay Glass: Glazed shutter and fixed glass portions to be provided with a glass of 5 mm plain float Glass. Mesh: Mesh shutter shall be provided with a stainless steel 32 guage Fly mesh of 304 grade with 144 holes per sq. Inch. Windows shall be provided with grill made of 10mm Sqm bars welded to at 150mm centre-to-centre, 6mm x 12mm MS flat Iron. Total grill unit should be powder coated and fixed to window frame with screws. Window frame should be fixed to brick/concrete masonory by using Nylon self-expanding caps and driving MS electroplated 80 mm long screws into the caps through frames. Note: The item includes everything as, painting the surfaces, fixing, all necessary accesories, glass, mesh, etc, all as per given spcifications, complete all as specified and directed by Engr-in-charge.This sould be compatible with cooler also). |
| 30 | Supply and fixingstainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. complete all as specified and directed by Engr-in-charges. |
| 31 | Supply and fixing for mild steel framed work as in cooler stand as in fixing by drilling/cutting the stone masonry wall and fixing for particle board & other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides), complete all as specified and as directed by the Engr-in-Charge. |
| 32 | Supply & fixing in repairs stainless steel decorative type curtain rod 22 to 25mm dia as per sample complete all as specified and directed by Engr-in-charges. |
| 33 | Supply & fixing of purpose made brackets trade pattern for stainless steel decorative type curtain rods suitable for holding 22 to 25mm dia as per sample as in repair. complete all as specified and directed by Engr-in-charges. |
| 34 | Supply & fixing of stainless steel decorative finials(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repair complete all as specified and directed by Engr-in-charges. |
| 35 | Supply only liquid water proofing compound, ISI marked complete all as specified and directed by Engr-in-charges. |
| 36 | Supplying & laying 03 coats of reinforced acrylic coating ‘New Coat’ as on sunken floor applied @1.5 Ltr/Sqm in 03 coats to achieve total 1mm thickness in any position including cleaning surface of sunken slabwith wire brush/mechanical brush and with water thoroughly to remove all dust/dirt and loose particles to expose base concrete/sunkenslab etc including repairing of loose/defectivejointsand applying 15mm thick plasterin CM 1:3 to level the surface and treatment to be applied all as per manufacturers instructions, complete all as specified and directed by Engr-in-charges. |
| 37 | Material & labourfor 100mm thick PCC 1:2:4 type B-1, (20mm graded aggregate) as in sunken floor complete all as specified and directed by Engr-in-charges. |
| 38 | Dismantling and taking down existing loose/ spalling/ unsound/ weaken concrete,unserviceable plaster from RCC components of any description and in any position until sound cocncrete substrate is obtained by chisel and hammer or using robust pneumatic chisel, hand tools including cutting of all edges, making square shoulders of the aperture, coarsen the smooth surfaces including necesary preparation of surfaces and cleaning the surface free from dust and debris etc. to ensure maximum bonding between the substrate and coating system including removing of all debris to a distance exceeding 1.5 Km but not exc. 5 Kmcomplete all as per manufacturer\"s instructions, complete all as specified and directed by Engr-in-charges. |
| 39 | M&L for preparation of surfaces cracks of plaster internal/external of walls, ceilings/Chajjas upto 5 mm wide, remove the loose plaster/concrete by suitable tools, filling cracks with crack paste compound and apply the second coat after 10-12 hrs of application of first coat including necessary scafolding of any height complete all as specified and directed by Engr-in-charges. |
| 40 | M&L for preparation of surfaces by cutting \"V\" groove cracks of plaster internal/external of walls, ceilings/Chajjas all along the crack 5 mm to 10 mm and remove the loose plaster/concrete by suitable tools, filling cracks with crack paste compound and apply the second coat after 10-12 hrs of application of first coat and for external application must be coated with paint including necessary scafolding of any height complete all as specified and directed by Engr-in-charges. |
| 41 | M&L for providing and fixing welded MS wire mesh weighing not less than 1 kg/sqm and dia not less than 0.9mm on the prepared surface which should be cleaned and should be removed from dirt, fungus and all foreign material. complete all as specified and directed by Engr-in-charges. |
| 42 | M&L for providing and applying thetreated surface with high quality repair mortar with polymer and fibre content .water ratio of which shall be 0.16, 28 days compressive strength shall be 30 MPa,mixed density shall be 2.18 kg/ltr, flexural strength shall be 6 MPa for 7 days and tensile strength for 7 days shall be more than 2MPa.Its adhesion bond strength shall be greater than 2 MPa with creep strain reduction of 8%. The modulus of elasticity of this product shall be 23-26 KN/mm². It shall not bleed / segregate on adding water and shall provide dual shrinkage compensation i.e – both plastic & hardened.Cement , sand can be used for finishing purpose. It shall be capable of being applied in thicknesses of 20 mm without sagging or falling and shall have minimum adhesive bond strength of 2 MPa.All cementitious systems have to be cured for a minimum period of 15 days by water curing, complete all as specified and directed by Engr-in-charges. |
| 43 | M & L for providing and applying a layer of high solids resin basedpigmented concrete compound (application 4.00 to 5.00Sqm/lit) Itforms a continuous membrane that controls hydrationfor strong and durable concrete .It should have specific gravity of 1.02. It can be applied by brush or can be sprayed, If sprayed the nozzle of the spray should be held approximately 450mm from the concrete surface and should be passed back and forth to ensure complete and even coverage. The pump pressure should be maintained at a level to produce a fine spray ensuring complete coverage of the surface, complete all as specified and directed by Engr-in-charges. |
| 44 | M&L for providing and applying two coats of water based Aliphatic acrylate -Anti-Carbonation coating for concrete surfaces over a coat of acrylic polymer primer. The coating to be applied on surface shall be liquid applied highly durable waterproof coating system for surface , based on high quality acrylic emulsion, functional filler, sunlight stable pigment and quality fungicides. It shall have properties that provide features like crack bridging ability, breathability, flexibility & exterior durability and resists micro-organism growth.It shall cover hairline cracks up to 0.5 mm effectively. It shall have excellent crack bridging ability and shall bridge cracks up to 2 mm width. The elongation at break is approx. 220 %. The tensile strength is 0.7 Mpa. It has a hardness shore ‘A’ scale of 80, with an adhesion strength of 3.4 Mpa. The coating is UV resistant, algae and fungus resistant, and has a water vapor permeability of 40 gm/m²/day and a crack bridging ability of 1-2 mm. The coating must be applied with temperature above 5°C and below 45°C. The coating shall be applied in two coats of by roller or brush application at the interval of 4-6 hours.Allow applied coating to dry or cure for 7 days , complete all specified and directed by Engineer-in-charge. |
| 45 | M&L for repairs to damaged surface of RCC elements like beams, columns, wall by removing all loose cement plaster/concrete, providing and laying of micro-concrete more than 20mm thickness (Average) by using the recommended water powder ratio mix the micro-concrete with pan mixer as per manufacturer\"s instruction including water tight shuttering necessary curing for 7 days complete all as specified and directed by Engr-in-charges.Note : Micro concrete will be measured and paid separately. |
| 46 | M&L for Providing and placing in position micro-concrete, grade M40, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, or equivalent make thickness of section upto 75 mm (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument) complete all as specified and directed by Engr-in-charges. NOTE - [a] The rate quoted for respective items shall be deemed to be inclusive of all material, labour, expert supervision, Tools, Plant, Safety measures like safety belts, ropes, helmets, netting etc. required to work upto G+ 1 floor height as per site requirement and providing double scaffolding and as required and removal of the same on completion of the repairs and disposal and depositing the demolished material outside MD land [b] The Structural repair works shall be got executed directly by the Manufacturer or through their authorised applicator |
| 47 | M&L for preparation of surface of reinforced bar by applying rust remover and then applying a coat of epoxy zinc primer on exposed reinforced surface complete all as specified and directed by Engr-in-charges. Note : Surface area for concrete shall be measured for payment purpose. |
| 48 | S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and directed by Engr-in-charges. |
| 49 | S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and directed by Engr-in-charges. |
| 50 | Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcementas required to facilitate demolition,complete all as specified and directed by Engr-in-charges. |
| 51 | Material and labour for RCC (1:2:4) type B-1 using 20 mm gradedstone aggregateas in chajjas, beams or columns etc upto double storey bldgs including necessary formwork complete all as specified and directed by Engr-in-charges. |
| 52 | Demolitioncement concretein any position not other wise specifically provided for complete all as specified and directed by Engr-in-charges. |
| 53 | Material and Labour for PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including WPC as per manufacturers instructions to achieve the slop required, with minimum thickness of 25mm consolidated and finished even and fair without using extra cement. (WPC shall be measured and paid separately complete all as specified and directed by Engr-in-charges. |
| 54 | M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed by Engr-in-charges. |
| 55 | Material andlabour providing and applying roof treatment as folowing stages :-(i) Apply 1st coat of PU coating (ShaliUrethane LHM @ 650 gm/Sqm or eqivalent by brush/roller/spray. Spread non-woven geo-textile or glass fiber tissue of 45 GDM with overlaps of 50mm in both directions when the surface is still tacky, this is optional , to be assessed as per site requirements to acheive higher mechanical properties.(ii) Allow 1st coat to dry for 10-12 Hrs.(iii) Apply 2nd coat of PU membrane (ShaliUrethane LHM @ 650 gm/Sqm or eqivalent) as per manufacturer\"s instructions. Extend waterproofing treatment up to 200mm and terminate into groov on the parapet wall.(iv) Protect the applied liquid membrane bu sprinkling sand @ 200gm/Sqm over the final coating when the surface is still tacky to facilitate plastering and including 25mm thick plastering in CM 1:3 with admixture and WPC. complete all as specified and directed by Engr-in-charges. Note1: Treatment shall be done through authrised representative of manufacturer\"s instructions.Note2: Dismanteling/removal of APP membrane and other treatment of roof includes as rate quoted by contractors, no extra amount paid on this account. |
| 56 | Taking down cement plaster from brick walls/stone masonry walls, concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and directed by Engr-in-charges. |
| 57 | Material andlabour for 15mm thick rendering in cement mortar (1:6) on stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-charges. |
| 58 | Material andLabour for 15mm thick rendering on fair faces of brick work masonry, concrete surfaces (external walls) or stone walls upto tripple storey bldgs in cement mortar 1:4 mixed with liquid water proofing compound using as per manufacturer’s instructions,finished even and fair, complete all as specified and directed by Engr-in-charges. Note : (i) WPC shall be measured and paid separately. (ii) Rendering upto 9 mtr ht shallbe included in the quoted rate). |
| 59 | Material andlabour10 mm thick cement plaster in cement mortar 1:3 on ceiling,finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charges. |
| 60 | M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty, complete all as specified and directed by Engr-in-charges. |
| 61 | Material & Labour for preparation of new plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over 1 mm putty to prepare surface even and smooth all complete all as specified and directed by Engr-in-charges. |
| 62 | Material & Labour for preparing new plastered surfaces and applying two coats of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty on ceiling complete all as specified and directed by Engr-in-charges. |
| 63 | M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of priming over a coat of 1 mm thick wall care putty on walls upto tripple storeys bldg complete all as specified and directed by Engr-in-charges. |
| 64 | M&L for preparation of old plastered or un-plastered surface to walls and applying Two or more coats of 100% Premium acrylic emulsion paint (Weather Proof Paint)having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engr-in-charges. |
| 65 | Material and labour for preparation of old Plastered or un-plastered surfaces ofceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of oil bound distemper (acrylic) white or tinted over a coat of 1 mm thick wall care putty complete all as specified and directed by Engr-in-charges. |
| 66 | M&L for two coat of synthetic enamel painting to new wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer complete all as specified and directed by Engr-in-charges. |
| 67 | M&L for two coat of synthetic enamel painting to new steel surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of red oxide primer complete all as specified and directed by Engr-in-charges. |
| 68 | M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc.complete all as specified and directed by Engr-in-charges. |
| 69 | Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floorsincluding taking down of old GI tubing, 40 mm bore complete all as specified and directed by Engr-in-charges. |
| 70 | Supply & fixedPolymer coloured (Polypropeylene Delrin and ABS) low levelflushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS discriptionmark with 2731 with andincluding suitable size of MS brackets, plug, screws all as required incl taking down existinghigh level/low level flushing cistern any type disconnecting pipes and jointingwith new one etcand making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed by Engr-in-charges. |
| 71 | Supply and fixing in repairs Vitreous ChinaW.H.B. white oval type counter below type of size 570 x 445 mm including waste coupling, waste pipe and brackets etc. complete all as specified and directed by Engr-in-charges. |
| 72 | Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified and directed by Engr-in-charges. |
| 73 | Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) &incl 01 No ‘P’ or ‘S’ trap of dia 100mm includingprovn of lime concrete bedding, complete all as specified and directed by Engr-in-charges. |
| 74 | Supply & fixed in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed by Engr-in-charges. |
| 75 | Supply andfixing in repairs, Urinal spreader of PTMT of miniumum weight 60 gms for fixing with 15 mm dia pipe., complete all as specified and directed by Engr-in-charges. |
| 76 | Supply andfixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks, complete all as specified and directed by Engr-in-charges. |
| 77 | Supply andfixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed by Engr-in-charges. |
| 78 | Supply andfixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and directed by Engr-in-charges. (Note : Weight of cock shall not be less than 0.575kg) |
| 79 | Supply & fixedin repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified and directed by Engr-in-charges. |
| 80 | S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union complete all as specified and directed by Engr-in-charges. |
| 81 | S&F in repair brass chromium plated tubular towel rail 20mm dia \"D\" type 60cm long between flanges complete all as specified and directed by Engr-in-charges. |
| 82 | Supply and Fixing in repair rotational molded polyethylene water storage tanks white tripple layered (cylindrical vertical with closed top) capacity 1000 Ltrhoisted and fixed in position complete all as specified and directed by Engr-in-charges. |
| 83 | S & F in repair gun metal globe/gate valves, with iron wheel head, screwed both ends for iron pipe flange ends type fixed of 20mm dia complete all as specified and directed by Engr-in-charges. |
| 84 | S&F in repair PTMT float ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore pipes complete all as specified and directed by Engr-in-charges. |
| 85 | Supply and fixing 1500 mm x 600 mm beveled edge mirror of selected quality glass mounted on 5.5 to 6 mm thick PVC sheet board & decorative teakwood beading all around including polishing and fixed to wooden plugs with CP brass screws and cup washers. complete all as specified and directed by Engr-in-charges. |
| 86 | Taking up or down steel tubing and connections of 15mm bore including cleaning for refixing or removal to store provision for branch connection by inserting tee union elbow etc. complete all as specified and directed by Engr-in-charges. |
| 87 | All as item above but 20mm bore, complete all as specified and directed by Engr-in-charges. |
| 88 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor complete all as specified and directed by Engr-in-charges. |
| 89 | Refixing old steel tubing of 20mm bore and connections in new or old position (Walls, ceiling, floors, etc. complete all as specified and directed by Engr-in-charges. |
| 90 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 20 mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor complete all as specified and directed by Engr-in-charges. |
| 91 | Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified and directed by Engr-in-charges. |
| 92 | Supply & fixed in repairs stainless steel grating openable 100mm dia with hole including fixing with white cement complete all as specified and directed by Engr-in-charges. |
| 93 | Supply & fixedin repair fancy type shower rose125mm dia sizeof Rim and 30cm long CP brass pipe with swiwel joint complete all as specified and directed by Engr-in-charges. |
| 94 | Supply & fixedin repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard andrailing 60cm long complete all as specified and directed by Engr-in-charges. |
| 95 | S & F for CP brass Soap Dish Holder, complete all as specified and directed by Engr-in-charges. |
| 96 | Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortarand taking out complete all as specified and directed by Engr-in-charges. |
| 97 | S&F 110mm dia UPVC (SWR) type \"B\" pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by Engr-in-charges. |
| 98 | S&F 110mm dia UPVC (SWR) type \"B\" pipe single sockets in any length with rubber ring joints, fixed to wall complete all as specified and directed by Engr-in-charges. |
| 99 | S&F 75mm dia UPVC (SWR) type \"B\" pipe single sockets in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by Engr-in-charges. |
| 100 | S&F 110mm dia UPVC (SWR) bends any radius including cutting of holes. complete all as specified and directed by Engr-in-charges. |
| 101 | S&F 75mm dia UPVC (SWR) bends any radius including cutting of holes. complete all as specified and directed by Engr-in-charges. |
| 102 | S&F 110mm dia UPVC (SWR) branch piece single (single \"Y\") equal or unequal. complete all as specified and directed by Engr-in-charges. |
| 103 | S&F 75mm dia UPVC (SWR) branch piece single (single \"Y\") equal or unequal. complete all as specified and directed by Engr-in-charges. |
| 104 | S&F 75mm dia UPVC (SWR) floor trap, plain with grating including jointing with solvant cement complete all as specified and directed by Engr-in-charges. |
| 105 | S&F 75mm dia UPVC (SWR) multi floor trap, with grating including jointing with solvant cement complete all as specified and directed by Engr-in-charges. |
| 106 | S&F UPVC (SWR) gully trap 125/110 mm setting and jointing with solvant cement complete all as specified and directed by Engr-in-charges. |
| 107 | S&F UPVC (SWR) vent cowl 110 mm bore setting and jointing complete all as specified and directed by Engr-in-charges. |
| 108 | Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-charges. |
| 109 | M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulatedstranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed on stone/brick masonrty wall surface with accessories having ISI mark fixed on wall surfaces / ceilingincluding provision of PVC box of appropriate size for fixing switches sockets etc. all as specifiedfor One light point / Fan/ bell point controlled by one switch. complete all as specified and directed by Engr-in-charges. |
| 110 | (a) One light point controlled by one switch with cables 1.5 sqmm size. |
| 111 | (b) One fan/ exhaust fan point controlled by one switch with cables 1.5 sqmm size. . |
| 112 | (c) One 3 pin socket outlet, 5 amps on the same board with other switches, with cables 1.5 sqmm size. |
| 113 | (d)One light point controlled by two 2 - way switches, with cables 1.5 sq.mm size. |
| 114 | (e) One 3 Pin socket oulet 5Amps on indepndent, with cables 1.5 Sqmm size |
| 115 | (f) One 3 Pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size |
| 116 | S&F switch piano flush type single pole one way 5/6 Amps. complete all as specified and directed by Engr-in-charges. |
| 117 | S&Fsocket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete includingdismantling old one. complete all as specified and directed by Engr-in-charges. |
| 118 | S&F ofswitch piano 15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge includingdismantling old one. complete all as specified and directed by Engr-in-charges. |
| 119 | S&F socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including dismantling old one. complete all as specified and directed by Engr-in-charges. |
| 120 | S&F ceiling rose surface tpe 3 terminals to be fixed on PVC block includingdismantling old one. complete all as specified and directed by Engr-in-charges. |
| 121 | S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd. complete all as specified and directed by Engr-in-charges. |
| 122 | S&F switch piano flush type single pole 16 Amp 2 way complete all as specified and directed by Engr-in-charges. |
| 123 | S&F lamp holder angle / batton typeinsulated body with back plate and to be fixed on PVC block. Including dismantling old one. complete all as specified and directed by Engr-in-charges. |
| 124 | S/F LED integrated batten tube light fittings 20W 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specified and directed by Engr-in-charges. |
| 125 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-charges. |
| 126 | M&L MCB TPN DB comprising of sheet metal enclosure double door suitable for mounting MCB 415 Volts 4 way includingdismantling old one. complete all as specified and directed by Engr-in-charges. |
| 127 | M&L MCB SPN DB comprising of sheet metal enclosure single door suitable for mounting MCB 240 Voltswithbusbar 200 amps rated 8 way includingdismantling old one. complete all as specified and directed by Engr-in-charges. |
| 128 | M&L MCB SPN DB comprising of sheet metal enclosure single door suitable for mounting MCB 240 Voltswithbusbar 200 amps rated 4 way includingdismantling old one. complete all as specified and directed by Engr-in-charges. |
| 129 | S&F MCB TP - 63 Amps 415V 10KA \"B\" curve miniature circuit breaker (MCB) and current carrying capacity in the DB complete with connection testing and commissioning. complete all as specified and directed by Engr-in-charges. |
| 130 | S&F RCBOs Double pole, 30mA 32 Amp rating for earth leakage, overload & short-circuit protection. complete all as specified and directed by Engr-in-charges. |
| 131 | Supply and fixing SPN 32 Amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. complete all as specified and directed by Engr-in-charges. |
| 132 | Supply and fixing SP 6 to 32 Amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. complete all as specified and directed by Engr-in-charges. |
| 133 | Taking down carefully, deposited to MES store and rehanging ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engr-in-charges. |
| 134 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers. complete all as specified and directed by Engr-in-charges. |
| 135 | Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade,for protection of earth lead complete all as specified and directed by Engr-in-charges. |
| 136 | Excavating in trenches n.exc 1.5 m widthand n.exc 1.5m in depth for taking out cable and cable coverand getting out in any type of soil complete all as specified and directed by Engr-in-charges. |
| 137 | Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm. complete all as specified and directed by Engr-in-charges. |
| 138 | Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed by Engr-in-charges. |
| 139 | M&L for spreading, levelling in layers n exc. 25 cm thick and ramming of sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables. complete all as specified and directed by Engr-in-charges.Note :- For the purpose of payment only punned thickness will be measured. |
| 140 | Supply and laying reinforced precast concrete cable cover, class LV,type 1 flat, 250mm x 150mm x 40mm. complete all as specified and directed by Engr-in-charges. |
| 141 | Taking out old unserviceable protection pipe and supply and fix medium grade50 mm dia GI pipe fix complete to wall , poles etc with suitable clamp for protection of cable complete all as specified and directed by Engr-in-charges. |
| 142 | Supply, laying and testing cable XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size35 sq mm 3.5 core in replacement. complete all as specified and directed by Engr-in-charges. |
| 143 | S&F Submain wiring alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x2.5sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required including taking down old wiring. complete all as specified and directed by Engr-in-charges.Note : Two run of 2.5 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM. |
| 144 | S&F Submain wiring alongwith earth wire with the following sizes of 2x4.0 sqmm + 1x4.0 sqmm earth wire FR PVC insulated copper conductor, single core cable in surface/recessed as required including taking down old wiring. complete all as specified and directed by Engr-in-charges. Note : Two run of 4.0 sqmm cable with colour code of R, Y & B for phase/ neutral and one run of same size cable with Green colour as earthing for socket point alongwith required PVC conduit and connected items will be measure as one RM. |
| 145 | S&F LED security light luminaries of 35 watt for energy saving having IP-65 degree of protection made of pressure die cast aluminum housing and heat resistant thoughned glass with excellent thermal management, LED\"s should have better optics and uniform distribution of light including GI tubing 40mm dia light grade 1.2 mtr long pipe bent to shape 120 degree for mounting of security light and fixed to wall/pole, with suitable MS clamps 2 Nos with nut and bolt and washers including connecting complete including 2.5 sqmm stranded copper conductor of suitable length complete all as specified and directed by Engr-in-charges. |
| 146 | Taking down old Sheet metal enclouser and supply and fix new sheet metal enclouser cubical type factory fabricated made out of 1.6 mm thick CRCA sheet with front sideopenable single door system powder coated painted to shade RAL 7032, PL Gasket, hinged single door ,IP-55 mounting plate made out of 2mm thick CRCA sheet steel and earth bolts etc. of size 600x450x200mm and making good finishes around the DB with cement and paint with existing colour complete all as specified and directed by Engr-in-charges. Note :-- Cost of any minor modification if required in fixing of the sheet metal enclouser as per site requirement and making good the disturbed surfaces matching with existing finish, will be deemed to be included in the cost of this item. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
