Tender For Construction Of 10 Beded Hospital At Rtc Karera, Itbp Mp, Karera-Madhya Pradesh

TDR : 53445645

Tender Notice
BOQ

18 Days Left

Karera , Madhya Pradesh

Tender Brief : Tender For Construction Of 10 Beded Hospital At Rtc Karera, Itbp Mp

Document Fees
Refer document

EMD
₹ 1087240.0 /-

Tender Value
Refer document

Submission Date
05-02-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil
2	Excavating trenches by mechanical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia
3	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
4	Excavating, supplying, stacking and filling of local earth (including royalty) by mechanicaltransport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.
5	Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.
6	Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift upto1.5 m. All kinds of soil.
7	Supplying chemical emulsion in sealed containers including delivery as specified . Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
8	Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
9	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
10	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
11	Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns
12	Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).
13	Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification.
14	Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.
15	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
16	Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for massconcrete
17	Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
18	Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.
19	Lintels, beams, plinth beams, girders, bressumers and cantilevers
20	Columns, Pillars, Piers, Abutments, Posts and Struts.
21	Stairs, (excluding landings) except spiral-staircases.
22	Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.
23	Edges of slabs and breaks in floors and walls Under 20 cm wide
24	Weather shade, Chajjas, corbels etc., including edges.
25	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
26	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
27	Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.5.33.1 All works upto plinth level5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum
28	5.33.2 All works above plinth level upto floor V level5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum
29	Add for using extra cement in the items of design mix over and above the specified cement content therein.
30	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
31	Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) :6.3.1 With F.P.S.(non modular) bricks
32	Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand)
33	Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks).
34	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm
35	Area of slab over 0.50 sqm
36	Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
37	Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete.
38	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
39	Extra for Providing and fixing flush doors with both side decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)
40	Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
41	26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.26.86.1 Frame size 45 x 70 mm
42	26.87 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)26.87.1 30 mm thick
43	Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.
44	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 300x10 mm
45	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 200x10 mm
46	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 150x10 mm
47	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10 mm
48	Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.
49	Providing and fixing aluminium handles of approved make anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessry screws etc. complete. 125 mm
50	Providing and fixing aluminium handles of approved make anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessry screws etc. complete. 100 mm
51	Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper
52	Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineerin-charge.
53	Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
54	Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick
55	Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows, Doors and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With aluminium Snap beading.
56	Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds. Casement Window with Double Rebate Frame with two Side Hung Glazed Panel and two Side Hung wire mesh Panel and Fixed Mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles on both glazed and fly screen panel. Using R3 series with frame (110mm & above ) x (45mm & above) & glazed sash (55mm & above) x (65mm & above) & fly screen sash (30mm & above) x (55mm & above) & mullion (55mm & above) x (65mm & above) & metal grill (if required to be paid separately). (Height upto 1.8 meter) Fixed window / ventilator with mullion / transom.
57	Using R1 series with frame (33mm & above ) x (35mm & above) & mullion (33mm & above) x (50mm & above). (Height upto 0.90 meter)
58	Ventilator Casement window single panel with or without fixed panel with S S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R1 series with frame (33mm & above ) x (35mm & above) & sash /mullion (33mm & above) x (50 mm & above). (Height upto 0.90 meter).
59	Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete.
60	Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 60 mm
61	Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 10.26.1 M.S. tube
62	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
63	Extra for pre finished nosing to treads of steps of marble / granite stone.
64	Extra for marble / granite stone flooring in treads of steps and risers using single length up to 2.00 metre.
65	11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.1.4 Size of Tile 800 x 1600 mm
66	Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 800 x 800 mm
67	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
68	Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
69	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase
70	12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)
71	15 mm cement plaster on rough side of single or half brick wall of mix :1:6 (1 cement: 6 coarse sand)
72	20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)
73	Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.
74	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.
75	Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work
76	Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
77	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
78	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.
79	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
80	Providing and fixing glazing in UPVC/ aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
81	Filling the gap in between aluminium frame and adjacent RCC/Brickwork/ Stone Work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge. Upto 5mm depth and 5mm width
82	Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
83	Supplying and Stacking Filling sunken floor with over burnt jhama brick aggregate 120mm to 40mm including compacting of materials complete as specified and directed for all levels.
84	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
85	Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
86	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
87	Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer
88	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm
89	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
90	Supply, Receiving, Storing & Fixing of CP brass wall mounted sink mixer with C.P. wall flange, swinging spout complete as required with flow rate of 6.0 LPM complying to Green Building requirements.
91	Providing,fixing,testing and commissioning Hand Shower (Health Faucet) with 8mm Dia,1 Metre Long Flexible Tube & Wall Hook of approved make and manufacture complete as per direction of Engineer in Charge.
92	Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.
93	Providing and fixing toilet paper holder C.P. brass
94	Supply, Receiving, Storing & Fixing of C.P. brass twin coat hook with PVC rawl plug & C.P. brass screw complete as required. Make :
95	Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15mm nominal bore
96	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
97	Providing and fixing Chromium Plated towel ring Rectangular shape with concealed fittings arrangement of approved quality and colour, of approved brand & manufacture complete as per direction of Engineer in Charge.
98	Providing and fixing of C. P. brass towel rail 600 x 20 mm size complete with C.P. brass brackets.
99	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
100	Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc.,complete.
101	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe. 40 mm dia
102	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet arm. 150 mm diameter
103	Providing and Fixing, testing and commissioning of CP Brass Telephone wall mixer with provision of overhead shower with 115mm long bend pipes on upper size with connecting legs , divertor and wall flanges with all accessories as required and making good the walls wherever required.
104	Providing and fixing CP brass soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
105	Supplying, Installation, Testing and Commissioning of vertical / horizontal storage type hot water heater fixed to wall with anchor bolts & nuts all complete work, (for Kitchen, Pantry & Toilets)20 Liter capacity.
106	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm dia nominal bore
107	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm dia nominal bore
108	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm dia nominal bore
109	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 50 mm dia nominal bore
110	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 65 mm dia nominal bore (Sch. 40)
111	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes
112	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes
113	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20mm nominal bore
114	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25mm nominal bore
115	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32mm nominal bore
116	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40mm nominal bore
117	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50mm nominal bore
118	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65mm nominal bore
119	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore
120	Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore
121	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
122	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks ofclass designation 7.5
123	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 110 mm (For Single & public toilets Soil & Waste Pipe).
124	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 75 mm (For Vent Pipe).
125	Supply, Installation, Testing and Commissioning of mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings & accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes & fittings with rubber sealing rings as per approved. 40 mm dia (For Urinal Soil Pipe).
126	Supplying, Installation, Testing and Commissioning of (PP/PP mineral), P or S trap of self cleansing design with / without vent. arm Setting in cement concrete 1:2:4 mix complete including cost of cutting & making good the Wall / Floors wherever required. 110 x110 mm outlet
127	Providing and fixing (PP/PP mineral) floor drain 110X75 size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects.
128	Providing & fixing (PP/PP mineral) clean out plug with uPVC socket fixed to uPVC pipe joints as required complete in all. 100 mm dia Pipe
129	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe
130	Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 75 mm dia pipe
131	Providing and fixing chrome plated grating with ring and two S.S screws of approved design with grating screwed down to the ring with s/s screws and embedding and setting ring into the floor with cement mortar.
132	Providing and fixing uPVC cowel of approved quality 110 mm
133	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.450 X 450mm -
134	Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
135	Supplying, Installation, Testing and Commissioning of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) for rain water pipes including all fittings rubber ring type (plain or with access door) e.g. bends, junctions, cowls, offsets, access pieces, jointing with rubber ring joints with lubricant etc. fixed with clamps to walls with cement concrete 1:2:4 blocks complete in all respects. (For rain water Pipe). 75 mm diameter
136	Supplying, Installation, Testing and Commissioning of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) for rain water pipes including all fittings rubber ring type (plain or with access door) e.g. bends, junctions, cowls, offsets, access pieces, jointing with rubber ring joints with lubricant etc. fixed with clamps to walls with cement concrete 1:2:4 blocks complete in all respects. (For rain water Pipe). 110 mm diameter (with all fittings)
137	Supplying and laying of following size HDPE DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 150 mm dia. Pipe
138	Supplying and laying of following size HDPE DWC pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 200 mm dia. pipe
139	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 150 mm dia. DWC & RCC Pipe
140	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 200 mm dia. DWC & RCC Pipe
141	Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design : 250 mm dia. DWC & RCC Pipe
142	Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 150 x 100mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
143	Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
144	Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe
145	Constructing brick masonry manhole in cement mortar 1:4 ( 1cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominalsize), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement andmaking channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
146	Extra for depth for manholes :Size 90x80 cm, With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
147	Extra for depth for manholes Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
148	Constructing brick masonry road gully chamber 50x45x60cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
149	Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture\"s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
150	Making connection of drain or sewer line with existing manholeincluding breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter
151	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit with modular switch modular plate suitable GI box and earthing the point with 1.5 sq.mm FRLS / HFFR PVC insulated copper conductor single core cable etc.as required. Group C
152	Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS / HFFR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS / HFFR PVC insulated copper conductor single core cable etc. as required. Group C
153	Wiring for power plug points with 2 x 4 sq.mm. FRLS / HFFR PVC insulated, Cu. Conductor, single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq.mm. FRLS / HFFR PVC insulated copper conductor single core cable for loop earthing as required.
154	Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS / HFFR PVC insulated, Cu. Conductor, single core cable in surface/ recessed medium class PVC conduit along with 2 Nos. 4 sq.mm. FRLS / HFFR PVC insulated copper conductor single core cable for loop earthing as required.
155	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 1.5 sq.mm. + 1 x 1.5 sq.mm. earth wire.
156	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
157	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
158	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS / HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
159	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
160	Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.
161	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
162	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non-residential buildings).
163	Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
164	Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet (near equipment point) and 25 A modular SP MCB, “C” curve (at accessible point) including connections, painting etc. as required.
165	Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
166	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
167	Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
168	Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.
169	Suppliying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc.as required. TV antenna socket outlet
170	Suppling and drawing co-axial TV cable RG-6 grade , 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC shealth in the existing surface/recessed steel/ PVC conduit as required.
171	Supply, Installation, Testing & Commissioning of CAT 6A UTP LSZH Cable, 23 AWG solid copper conductors in accordance to TIA/EIA 568 C.2 (Category 6a) & ISO/IEC 11801 2nd ed(Class Ea), UL Approved, tested @500 Mhz, with HDPE insulation of individual conductor and over all Dia of 7.2 mm for Connectivity of Hub room to End Point. Grey Color.
172	Supply, Installation, Testing & Commissioning of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.
173	Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6A UTP, loaded Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.
174	Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.
175	Supply, Installation, Testing & Commissioning of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.
176	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)
177	Supply, Installation, Testing & Commissioning of 15 U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. & 5Nos. 6/16A sockets PDU also complete as required.
178	Supplying and fixing of following sizes of Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm
179	Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in the cubical panel, making connections etc. as required. (for VTPN DB) 100/63 A,36KA,FP MCCB
180	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), 8 Way (4+24), Double Door
181	Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way Double door (4 + 24)
182	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface / recess, complete with testing and commissioning etc.as required. For 8 way, Double door TPN MCBDB
183	Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required.
184	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole
185	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Double pole
186	Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole
187	Supplying and fixing of following rating, four pole 415 V , Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amp
188	Supplying and fixing of following rating, four pole 415 V , Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp
189	Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. 40 Amps
190	Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required. 63 Amp
191	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 8-10WATT
192	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 12-15 WATT
193	LED Down lighter (SMD Type) (System lumen efficacy ≥120<135lm/Watt)Supplying, installation, Testing & Commissioning of LED Recessed/surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%,P. F.≥0.95,Rating) , IP20, CRI >80, UGR(Unified GlareRating) <19Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim. 18 WATT
194	LED Batten light (System lumen efficacy ≥105 <120lm/Watt) Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) 18-22 WATT
195	LED Batten light (System lumen efficacy ≥105 <120lm/Watt) Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) 40watt
196	Supplying and fixing single wall mounted 9/10 watt (2ft long) LED type batten fitting complete with electronic driver and LED etcdirectly on wall/ceiling including connections with 1.5sq.mm FRPVC insulated copper conductor and earthing the body etc. as required.
197	Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1400 MM Ceiling fan
198	Supplying, Installation, Testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 3 meter and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required
199	Design, Manufacturing, Supply, Installation, Testing & Commissioning of cubicle type totally enclosed free standing / Wall mounted type moisture, dust and vermin proof compartmentlized Floor Distribution Panel made out of 2.0 mm thick of Main members & front cover 1.6 mm thick CRCA sheet complete with internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. y. The MCCB rating up to 250A shall have thermal megnatic based adjustable over current, short circuit protection and above 250A MCCB shall have microprocessor based adjustable over current, short circuit, earth fault protection. All Main Distribution board / Sub Distribution board / Meter boards which are located inside various blocks shall be partially Type Tested assemblies (PTTA) as per conforming to IEC-61439-1 The Moulded Case Circuit Breaker shall have a minimum fault breaking capacity (Ics) of not less than 35 KA & 25KA RMS for one second at 415 volts for MDB / SDB respectively. MCCB‘s above 63A should be provided with Copper & procader terminals. Incomer of Meter Board shall have a minimum short circuit breaking capacity (Ics) of 25KA for one second at 415volt.INCOMING, 1 No. 200 Amp FP,36KA, Moulded Case Circuit Breaker1 Set of phase indicating lamps with MCB.1 Set of ON/OFF indicating lamps with MCB.1 No.Digital Voltmeter with Voltmeter selector switch.1 No.Digital Ammeter with Ammeter selector switch.1 NO. SPD with Protection fuse.BUSBAR, 250 Amp TPN aluminium busbar with coloured heat shrinkable sleeve.OUTGOINGS, 1 No125 Amp FP,25 KA, Moulded Case Circuit Breaker3 No100 Amp FP,25 KA, Moulded Case Circuit Breaker2 No 63 Amp FP,25 KA, Moulded Case Circuit Breaker1 Nos. 63 Amp DP Miniature Circuit Breaker.Panel described as above
200	Earthing with GI earth Pipe 4.5 mtr long 40 mm dia including accesories and providing masonary enclosure with cover plate having locking arrangement of 2.7 mtr long etc with charcoal/cock and salt as required
201	Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
202	Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
203	Providing and fixing GI tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
204	Providing and fixing GI tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
205	Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.
206	Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.
207	Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
208	Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
209	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 3.5 core, 95 sq.mm.
210	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 3.5 core, 50 sq.mm.
211	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 10 sq.mm.
212	Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. 4 core, 25 sq.mm.
213	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc.as required. Upto 35 sq. mm (clamped with cable tie)
214	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray/surface as required. Upto 35 sq. mm (clamped with cable tie)
215	Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray/surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with cable tie)
216	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 95 sq. mm (45mm)
217	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 50 sq. mm (35mm)
218	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 25 sq. mm (28mm)
219	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 10 sq. mm (25mm) (used for 4 x 6 sq. mm & 4 x 4 sq. mm cable)
220	Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.inclunding Bends & TEE etc. 100 mm width x 50 mm depth x 1.6 mm thickness
221	Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature). Inverter Type - Cooling only 1.5 TR with 5 Star BEE Rating
222	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (suction line)(2.0 TR) -6.4 mm dia
223	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (Liquid line)(2.0 TR)-12.7 mm dia
224	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (suction line)(1.5 TR)-6.4 mm dia
225	Providing and fixing of soft drawn copper refregerent pipe i/c accessories,bracing with necessary supports as required (for beyond 4 mtrs of split AC units) Of suitable of above item and pdg insulation with nitrile rubber in performed tubular suction (Liquid line)(1.5 TR)-12.7 mm dia
226	Providing and fixing factory fabricated floor/wall mounted type MS angle iron frame suitable for installing of split AC outdoor unit material etc as required.
227	Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520, (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-\"F\" insulation, conforming to IS-325. (D) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (E ) Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head (1W+1S)
228	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 x 25 sqmm ( 28 mm )
229	Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred. 4 core, 25 sq.mm. Aluminium Armoured
230	Providing, fixing, testing and commissioning of control panel for Terrace Booster pumps .Incoming: MCCB 35A 1 set of Phase indicating lamps, 1 set of 35A Al bus bars, 1No Ammeter, 1No Voltmeter with phase selector switch Feeder for Booster Pumps - 1 No. 1 No. 32A TP MCCB without releases. DOL starter with over load relay, single phase preventor and indicating lamps with ON/OFF push buttons. 2No. Automanual selector switch. Suitable for booster pumps
231	Providing & fixing of heavy class M.S. pipes conforming to IS: 1239/3589 complete with fittings including trenching and refilling etc. (external work) including all fittings and accessories like tees, elbows, flanged joints, rubber insertion, nuts, bolts or cutting and welding joints. Providing thrust block at distance specified as per specifications. (Pipe shall be provided with anti corrosive protective treatment with coal tar/asphalt tape confirming to IS: 10221 standard complete as per specification). All work complete as per specification and as directed by Engineer-In-Charge. (All the fitting i.e. tee /elbow etc. for Valve connections etc. will be flanged joints)( Heavy duty pipe 80 mm dia
232	Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (The Welding shall not be done for piping less than 50 mm dia.) 80 mm dia
233	Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless Steel (Internal)
234	Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. 80 mm dia
235	Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia
236	Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80 mm dia
237	Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)
238	Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
239	Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.40 m
240	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)
241	Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way - 100 mm dia M.S. Pipe
242	Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
243	Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
244	Providing & fixing heavy duty double flanged flexicon rubber expansion joint (suitable for system test pressure) of standard length as per manufacturers specs including rubber gaskets, flanges, nuts, bolts and washers complete as required. 80 mm dia
245	Supplying and fixing fire hose cabinet fabricated from 16 gauge M.S. Sheet with single or double glazed front door (with 4 mm thick glass) and locking arrangement, painted fire red with stove enamelled paint \"FIRE HOSE\" written on front including necessary supports approximate size. a)750mm x 600mm x 250mm deep. (Internal only for hose reel)
246	Supplying and fixing of Fire Man\"s axe with heavy insulated rubber as per standard conforming to IS 926.
247	Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge. 4.5kg capacity cylinder
248	Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge. Dry Chemical Powder ABC type of 6 Kg as per IS:15683
249	Providing and placing in position Semi-Motorized Bed of overall dimensions : 2100mm(L) x 1050mm(W) x Height Adjustable from 490mm to 750mm,Three Electric operated features are Backrest, Legrest , High-Low(Only one handset will be provided).Two function mechanically operated bed : Trend/ Reverse trend. Note: Height of bed for TR and ATR is 650mm from the ground and above.Min ht: should be 490 mm; Max ht: 750 mm without mattress,Back rest angular movement: 65 deg; Knee rest angular movement: 30 deg. Trendlenburg 12 degree and Reverse trendelenburg 8 degree.Safe working load should be 200 kgs Patient load bearing capacity: 135 kgs.All edges in contact with patient to be rounded safely.Head & Foot board should be made of blow molded Poly propylene with bacteriostatic additives . Head board and foot board should be with metal inserts to mount it on bed frame. Removable PP head board and foot board should have cut out , for better gripping. Bed frame should be made of MS ERW tube of size 50mmx25mm of 2 mm thick supported with ERW square tube with 25 mm x 25 mm and 1.2 mm thick. All corners of bed frame are provided with bumper mounting holders and it should have provision 4 iv pole holders.Base frame should be made of MS ERW tube of size 30mmx60mm of 2mm thick. Base frame should have ground clearance of greater than 150 mm to avoid any obstruction during bed movement. Base frame should have provison to mount oxygen cylinder cage. It should have trendelenburg indicator guide.Bed lying surface should be made of PP injection mould . This lying surface should have sections for bed profiling i.e. back adjustment, fixed pelvic section, upper and lower leg adjustment.Lower leg rest section is provided with Ratchet for leg rest adjustment with a single hand operation to acheive the position. Mattress platform is strengthned by frame of size 25 mm x 25 mm and 1.2 mm thick.Under bed clearance should be greater than 150 mm.Bed mechanisim is made of linkages which are made by HR MS flat of size 40mmW x 10mm thick. This mechanism should be operated with the help of lead screws and crank. Lead screws should be made from EN8 and ACME threads roll formed. It should be functioning on the basis of Synchornised Linear Roller Mechanism(SLRM). SLRM is assisted by tension spring covered with telescopic tube with plastic end gaps. The manual function is operated with the help of an ergonomically dedicated handle, which is made of metal inserted PP co polymer , it should be snap locked when not in use. There should be operating guidance sticker for the manual operation.4 Neoprene rotating bumpers of dia 92mm height 69mm with 40-50 shore hardness are provided at four corners to protect the bed and patient from impact and avoid damages to wall.Handle to operate manual function on crank made of PP injection moulded. Handle should be snap locking which can be kept in folding position when not in use. Handle parking provision to be given in bed.The bed should be provided with 125mm wheel dia,twin wheel ,plastic polymer with metal insert castors. Out of 4 castors two should be provided with brake, mounted at diagonally opposite position.Ergonomically designed plastic handle having opening mechanism in 90 deg position. Handle levers fold compactly upwards with snap fit when not in use. Handles are self with a brass insert and a chrome plated knob with a Nylon grip. The bed should be provided with PP molded side boards of 4 no\"s providing full coverage to bed. These side boards should be with bacteriostatic additives. These side boards should be integrated with drop down mechanism for easy operation. The side boards should be provoded with angle indicators.The bed should have MS powder coated urine bag holder on both side of the bed for ease of accessibility.To ensure qood quality welding \" Co2 Argon\" process should be adhered to.All metal components should be pre treated with zinc phosphating in 7 tank porcess and then powder coated with bacteriostatic epoxy polyster powder coating to fulfill the requirements for bacterial protection against at least 2 commonly found bacteria in Hospital environment [Gram positive and Gram Negative].proof loading test , cycle tests , impact test, horizontal & vertical load tests for side rails, salt spray test, castor break test, pull test for head and foot board.Electrical details: Supply Voltage : 100-240VAC +/- 10%; Current: 2.5A max, Electric Shock Protection: ClassI, Type B, Liquid Ingress protection IPx4, Duty Cycle 10% or max 2min continuous ON followed by 18min continuous OFF, Three Electric operated features are Backrest, Legrest , High-Low(Only one handset will be provided).The has provision for front loading medium sized ms made oxygen cylinder cage.The bed should be provided with Telescopic IV pole made of Stainless steel to mount saline bags.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
250	Providing and Placing in position Mattress for Semi-Motorised Bed. The bed should be provided with 40 density 100 mm thick PU foam mattress with ridges for easy bending. It should be covered by heavy helium material which is water proof, flame retardant, vapour & Xray permeable with bacteriostatic properties. The zip & stitches for the mattress cover should be concealed. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
251	Bed Side Locker has cabinet with lock and with plastic molded handle. There is space between plastic top and cabinet to keep the general items for the frequent use. Cabinet is provided with lock to keep the valuable items for the safety. Overall Size (in mm): 490L x 410W x 941H Material Specifications: 4Corner Tube made from ERW Round Tube of Section Æ 25.4mm having thickness 1.2mm. 4Cabinet made from 0.8mm thick CRCA Sheet, and is provided with lock. 4Top made from ABS of Section 2.2mm. Top has recessed and contoured shape for the better aesthic and usability. 4Knob made from Plastic molded knob with Matt finish with generous radii and dome shape for better grip. 4Castors of Section Æ 50mm made from Plastic molded castor placed in diagonal lokcing arrangement. Finish Specification: Anti microbial and thermosetting eproxy polyester Powder coating, formulated to fulfill the requirements for bacterial protection. Colour RAL White & Plastic parts in Grey.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
252	Doctor\"s table :-Supplying and placing in position of Director\"s Desk with Leatherette Desk Pad size :- (W)1800mm X (D)1690mm X (H)760mm. Table Top Thickness : 80mm. Our Danbury office collection is a study in blending timeless elegance with practical design. The masterfully curved silhouette puts the spotlight on intricate moulding and elegant panel design with a leatherette accent. Designed with a movable drawer pedestal and side runner, this managerial desk ensures a clutter-free work area, while the leatherette desk pad and cable organizer add a functional flair. Crafted from premium engineered wood in Walnut finish. Spacious tabletop offers ample workspace, ideal for multitasking and large projects. Gently curved silhouette with intricate moulding and leatherette accent adds a statement appeal. A leatherette desk pad offers a smooth and durable surface for writing and daily tasks. A movable pedestal unit features 3 spacious drawers. A side runner features 1 cabinet, 1 drawer, 1 shelf, a dedicated CPU shelf and a trolley. A keyboard trolley offers a clutter-free workspace. 2 Circular cable organisers keep the tabletop clutter-free. A dedicated CPU unit keeps your CPU neatly stored, leaving your desk clutter-free. Premium PU polish with low chemical emissions ensures healthy indoor air. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
253	Supplying and Placing in Position of High back fabric chair High back 360° degre revolving chair All over size is : 620mm(l)x 6800mm(d)x 1130mm(h) , bifam certified chair made of full upholstery polister fabric with 129 gsm .,it will comes in matte finsih in contemporary style . Details : Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat and back) . Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support mechanism : single locking mechanism . Only seat depth is @ 525mm(d) & the back size is 480mm(l)x 610mm(h) , Seat maximum height is 535mm & minimum height is 435mm & back height from floor maximum height is 1045mm & minimum height is 1145mm gas lift 100 mm telescopic haudraulic base : 650 mm chrome base with smooth castors . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
254	Supplying and Placing in Position of fix multi purpouse fabric chair with matte finish All over size is : 609mm(l)x 495mm(d)x 1143mm(h) , The chair made of full fabric. It will comes in matte finsih in contemporary style . Details : Arms : two way adjustable pu padded arms with up & down position. Use of ply: seat & back plywood made of 12 mm hot pressed. Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in back . backrest support foam design based on symmetrical lumbar support only seat size is 480mm(l)x 500mm(d)x 480mm(h). Base :m.s powder coated tublar frame of catilever type .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
255	Semi Fowler Bed- Single Function bed which has an adjustable backrest and a fixed lower section. Overall Size in mm : 2268 (L) x 922 (W) x 610 (H) Material Specification :1. Bed Frame made from (a) MS ERW Rect. Tube of section 30mm x 60mm and thickness 1.6 mm (b) MS ERW Round tube of section 30 mm x 30 mm and thickness 1.6 mm. 2. Laying Surface Frame made from MS ERW Round Tube of section Æ 25.4mm and thickness 1.6 mm. 3. Head Board/Leg Board Frame made from MS Round Tube of section Æ19, Æ25.4 & Æ31.75 mm and Thickness 1.6 mm with Higher diameter tube provides a studay understracture. 4. Lead Screw EN8 ACME 6 MM Pitch Thread Rolled En8 Lead Screw,with ACME thread and 6mm pitch gives good strrength, with ease of opreation.5. Handle PPCO Snap Locking Handle lever with handle body keep it in folding position when not use. 6. Lying Surfaces CRCA 1.0 mm Laying Surface area consists of mattress ratainer to define the position of the mattress.7. Castors High endurance metal series castor and provided with dual locking arrangement are diagonally placed wheel Dia 125mm & Stem dia is 22mm. Diagonal locking provides better s stability to bed in the locked position. 8. Mosquito Net Ple Holder: Privision for mounting of mosquito net pole.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
256	Bed Side Locker has cabinet with lock and with plastic molded handle. There is space between plastic top and cabinet to keep the general items for the frequent use. Cabinet is provided with lock to keep the valuable items for the safety. Overall Size (in mm): 490L x 410W x 941H Material Specifications: 4Corner Tube made from ERW Round Tube of Section Æ 25.4mm having thickness 1.2mm. 4Cabinet made from 0.8mm thick CRCA Sheet, and is provided with lock. 4Top made from ABS of Section 2.2mm. Top has recessed and contoured shape for the better aesthic and usability. 4Knob made from Plastic molded knob with Matt finish with generous radii and dome shape for better grip. 4Castors of Section Æ 50mm made from Plastic molded castor placed in diagonal lokcing arrangement. Finish Specification: Anti microbial and thermosetting eproxy polyester Powder coating, formulated to fulfill the requirements for bacterial protection. Colour RAL White & Plastic parts in Grey.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
257	Examination Bed- Examination Table of Overall Sizes (L)1957mm x (W)625mm x (H)808mm having gas-lift assisted head rest with continuous adjustment from 0° to 30°. The design focuses on ease of operation, hygiene, doctor and patient ergonomics, and aesthetics.Homogeneous soft forms with rounded edges evoke feeling of comfort and safety. Material Specification - Mattress and Up-holstery is made with PU molded foam with density 50-55, of 625mm x 65mm section, of 23 mm thickness. Mattress is projecting out from the understructure to provide soft touch from all sides.Seamless upholstery is provided to avoid spread of bacteria. Head Rest is made of PU molded foam with density 50-55, Section is made of 625mm x 65 mm.Thickness is 23mm. Gas-lift assisted head rest with continuous adjustment from 0° to 30°. UnderStructure and top frame is made of ERW square tube , os section 30mm X 30mm and 1.6 mm. Understructure is made of MS square tubes with unique styling that provides better strength and stability. It is provided to reduce visual clutter and offers better access and reach.\"Top Drawer Unit is provided, made of CRCA sheet construction with SS handle & SS hinge. Sheet thickness 1.2 ,0.8 and 0.6. Two drawers at top; each of volume 510 x 334 x 95 mm are provided\". \"BP Apparatus tray: CRCA sheet construction with SS handle and SS hinge Dia 10 for handle. Sheet thickness 1.2 ,0.8 and 0.6. swivel tray is designed for BP Apparatus that can be concealed when not in use. SS Handle: SS 202 Dia 10 - The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified. Aesthetically designed handles are placed in such a way that gives a unique look also provide wider space for griping to users. \"Ergonomics: Increased width of the table (625mm) gives better comfort for patients. Optimized height (808mm) of the table for comfortable observation and reach. Tapered shape is provided to give a unique look and better access for doctor. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
258	Supplying and placing three seater exclusive premium leatherette modernist classic design lounge seating sofa size is 1650mm(l) x750mm(d)x 710mm(h) with kiln-dried wood framing makes it warp and scratch resistant,comfortable seat depth & height designed keeping modern indian lifestyle in mind,wrapped in buttery-soft premium leatherette, the panelled back and cushioned armrests encourage lounging,designed with modernity & elegance, choose the option that suits your home. Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried german beech wood framing is highly durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue ,the frame shall be padded with high resilience polyurethane foam having 25 +/- 5 density in seat it shall be stack foam of 40mm thik,40mm thick back foam having 25 +/- 5 density foam used ,there shall be cushion arm 40mm thick provided padded with high resilience polyurethane foam having density 25 +/- 5. the complete stack foam structure shall be covered with premium leatherette in brown-camel brown colour, it complements the modish sleek steel . ( seat : 545 mm(d) x 410mm(h) , arms height @ 610 mm / back height @ 290 mm).The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
259	Supplying And Placing Three Seater Airport Waiting Area Chair With 2 Soket. The Dimension Of Airport Waiting Area Chair Shall Be Min. Overall Length -1764mm, Min. Overall Height - 875mm, Min. Overall Depth Is 680mm, Min. Leg Length Is 635mm, Premiumoor To Seat Height At Front Shall Be Min. 425mm, Width And Premiumoor To Armrest Height Shall Be 630mm Respectively. The Thickness Of Seat And Lumber Support Area Shall Be Min 40 mm. The Chair Shall Be On Main Frame Of Extruded Aluminium Of Minimum Thickness 4.0 mm And Appropriate Cross Section So As To Achieve The Required Strength And Durability As Per Latest Bifma X5.4 Standard With Powder Coating Of Minimum 70 Microns. The Ends Shall Be Aesthetically Designed And Plugged With End Caps Having Suitable Fixing Arrangement.The Seat And Backrest Shall Be Of Integral Type Made From High Density Self -Skinned Integral Pu Foam Coloured In The Mass Reinforced With Outer Steel Frame Of Maximum 60 mm Width With Following Options, And Thickness So As To Achieve The Durability As Per Latest Bifma X5.4 Standard:1. Pu Without Inserts Integrated In Outer Steel Frame Or2. Pu With Inserts Of Wire Mesh Integrated In Outer Steel Frame Or3. Pu With Steel Strips Integrated In Outer Steel Frame Or4. Pu With Steel Springs Integrated In Outer Steel Frame.The Profile Of The Integral System Should Ensure Comfortable Sitting And Lumber Support Having Ergonomic Profile And Thigh Support. The Seat Should Have Slant Towards Backwards For Comfort. The Thickness, Hardness And Density Of The Pu Moulded Foam Seat Should Guarantee Satisfactory Level Of Comfort For The User. The Density Should Be Minimum 300 Kg/Cum. The Shore \"A\" Hardness Should Be Between 45 To 85.Seat And Backrest May Either Be One Single Unit Or Separate Seat And Back In Two Separate Units. The Seat And Backrest Should Comply With The Fire-Retardant Norms Bs 5852, Crib 5 Test Method Or En 1021:1, En 1021:2 Or Equivalent Indian Standard. The Seat And Backrest Shall Be Fixed On The Main Frame Conveniently Ensuring Screws, Nuts And Bolts Are Not Directly Intruded In The Pu Of Seat And Back But Fitted In Metal Parts. The Frame Support (Base/Legs) Shall Be Of High Pressure Aluminium Die Cast. The Base/ Legs And Seating Shall Be Fixed On The Main Frame With Conveniently Fixed Armrests In Such A Way That Assembling/Dismantling Is Easy And Interchangeability Of Seats And Armrests Is Possible. The Assembly Shall Also Be Capable Of Providing Side Table. The Chair Shall Not Develop Any Structural Failure Within A Period Of Seven Years And The Manufacturing Company Shall Submit A Confirmation Certificate To Meet This Requirement. The Assembly Shall Also Ensure That All Nuts, Bolts And Screws Are Concealed Without Protruding And Maintains Overall Aesthetics. There Should Not Be Any Sharp Edges. The Chair Shall Not Get Displaced Due To Frequent Occupying And Vacating Of Chair By Passengers And Should Have Minimum Weight Of 55 Kg. There Shall Be Provision Of Both Power Socket And Usb Charging Point Along With Cover/Closing Plates For Use In Future As Decided By Eic.The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
260	Suppling & placining position of Center table as per photograph. Center table size :- (W)1200mm X (D)600mm X (H)460mm. Masterfully crafted from kiln-dried solid wood in Danish Teak finish.Gently rounded tabletop appears to float above slender, tapered legs for an airy silhouette.Subtly recessed apron highlights the refined, minimalist form.Smooth, rounded edges soften the profile and catch the light beautifully.Compact footprint perfectly suited to modern living spaces.Buffers ensure smooth, easy mobility while protecting floors from scratches. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
261	Supplying and Placing in Potision of table as per photograph. table over all size is 1200mm(l)x 600mm(d)x 750mm(h) 25mm thick table top made of prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue . modesty pannel made of mm thick.understructure made of 18mm thick with wire management hole with pvc grooment on table top. Provision of Fixed pedestal of size is 450mm(l)x 400mm(d)x 725mm(h) fixed pedestal with 3 drawers + left side on filling storage shelve. 1 filing box fixed pedestal + 1 fixed pedestal with 3 equal drawersin provided with cetnral lock for security and handles are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
262	Supplying and placing in position of medium back 360° degre revolving chair ,All over size is : 640mm(l)x 670mm(d)x 1100mm(h) , The chair made of full mesh .It will comes in matte finsih about style type is modren. Details :- Arms : amrest is having two adjustment heights (up & down) . Use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , Back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support, Mechanism : self weighted multi locking mechanism . Only seat size is 500mm(l)x 500mm(d)x 540-440mm(h) & the back size is 480mm(l)x 570mm(h) . Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm . Gas lift 100 mm telescopic haudraulic , Base : 650 mm chrome prong base is 620mm pitch center dia (660mm with castors) . The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
263	Supplying and placing in position of reception desk a combination of steel,glass and wood make the products utile and a delight.timeless design that elevates your office space structure of spacious reception desk,tabletop offers you a generous look for work surface use premium quality materials over all size is 2400 mm(l)x 900 mm(d)x 750 mm(h) which give more surface area for work ,table top made of 25mm thick also table top based on side panel\"s made 18mm thick prelaminated particle board of grade ii type iii of is 12823/latest.combination construction of reception desk above table 18 mm thick counter top with glass height from table top @ 350mm,10 mm thick clear glass diamond cut finish on edes based on stainles steel stud grade 304,overall reception desk height is @ 1100mm with glass,on table top pvc groment hole for wire management & top made 25 mm thick prelam particle board work surface with the exposed edges shall be finished with 2mm thick pvc edge binding tape of matching colour and shade fixed with hot melt glue along with breathable mesh modestly panel made 0.8mm thick metal powder coated to the thickness 50-60 microns(+/-5 micron).2 mobile pedestal (2 drawers + 1 filing cabinet ) + (2 drawers + 1 filing cabinet ) both pedestal comes in same size is 450 mm(l)x 450 mm(d)x 725 mm(h) in provided with central lock\"s for security and handle\"s are provided for easy of opening & pedestal\"s move on nylon castors .The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
264	Suppling & Placing Position of Smart Series table asper photograph.Main Table Size ;- L-1350mm x D-600mm H-750mm. Main Table top :- made of 25mm thick prelamparticle board with 2mm Thick PVC edge banding. Table top supported : with powder coated slantshape metal legs of size 50 mm x 50mm andconnectors of size 25mm x 50mm horizontalconnectors. Modesty Panel :18 mm thick Modesty panelprelaminated particle board With 2mm Thick PvcEdgebanding. 6 module Access flip & electrical pole below top forwiring Provision of 2 Nos . Mobile Pedestal of 2 Drawer + 1 Filling unit, made of18mm thick Prelaminated Particle Board with PVCedge banding. All drawers shall have a central lockmechanism. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.
265	Suppling & Placing Position of Smart Series table asper photograph.Main Table Size ;- L-1500mm x L-1500mm x D-600mm H-750mm. Main Table top :- made of 25mm thick prelamparticle board with 2mm Thick PVC edge banding. Table top supported : with powder coated slantshape metal legs of size 50 mm x 50mm andconnectors of size 25mm x 50mm horizontalconnectors. Modesty Panel :18 mm thick Modesty panelprelaminated particle board With 2mm Thick PvcEdgebanding. 6 module Access flip & electrical pole below top forwiring Provision of 2 Nos . Mobile Pedestal of 2 Drawer + 1 Filling unit, made of18mm thick Prelaminated Particle Board with PVCedge banding. All drawers shall have a central lockmechanism. The OEM/ Bidder should have the following certification ISO: 9001:2008; ISO: 14001:2004; ISO: 18001:2007, ISO 45001, UL Greengaurd, FSC, Green Pro, Indian Design Mark and AIOTA for ergonomically design of relevant category of products. The OEM/ Bidder should also be a member of BIFMA since 15 years and one or more products of the OEM should be certified as BIFMA COMPLAINT as well as BIFMA LEVEL ONE certified.

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Madhya Pradesh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of 10 Beded Hospital At Rtc Karera, Itbp Mp, Karera-Madhya Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of 10 Beded Hospital At Rtc Karera, Itbp Mp, Karera-Madhya Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us