|
| 1 | Earth work in rough excavation, bankingexcavated earth in layers notexceeding20 cm in depth,breaking clods watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : |
| 2 | All kinds of soil |
| 3 | Constructionof granular sub base by providing close grade Material,mixing in a mechanical mix plant at OMC, carriage of mixed material to work site,spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density,complete as per clause 401 |
| 4 | Grading - I Material |
| 5 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. |
| 6 | Local best quality Tolhao wood. |
| 7 | 35 mm thick shutters |
| 8 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 9 | 0.80mm thick with zinc coating not less than 275gm/m2 |
| 10 | Providing ridges or hips of width 60 cm over all width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. |
| 11 | 0.80mm thick with zinc coating not less than 275gm/m2 |
| 12 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with |
| 13 | Precoated galvanised iron profile sheets0.50 mm thick |
| 14 | Providing and fixing precoated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : |
| 15 | Ridges plain (500 - 600mm). |
| 16 | Precoated galvanised iron profile sheets0.50 mm thick |
| 17 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to thedumping ground within 50 metres lead : |
| 18 | With cement mortar 1:4 (1 cement: 4 coarse sand) |
| 19 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 20 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 21 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade |
| 22 | New work (two or more coats) over and including priming coat with cement primer:- |
| 23 | Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to preparethe surface even and smooth complete. |
| 24 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 25 | Two or more coats on new work over an under coat of suitableshade withordinary paint of approved brand and manufacture. |
| 26 | Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 27 | 40mm thick with 20mm nominal size stone aggregate. |
| 28 | Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (framework to be paid separately): |
| 29 | Natural colour insulating board |
| 30 | 3 mm thick |
| 31 | ProvidingandfixingUPVCsoil,waste,rainwaterandvent pipes includingall requisite fittings,jointingofpipes&fittingswithsolventcement, trenching, refilling&testing of joints complete as per direction of Engineer in charge |
| 32 | 110mm dia. |
| 33 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 34 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 35 | 10 litre capacity - White |
| 36 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 37 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 |
| 38 | 15 mm nominal bore |
| 39 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 40 | 15 mm nominal bore |
| 41 | Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms |
