|
| 1 | Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in any type of soil, including removal of the rubish upto 50m, complete all as specified and as directed. |
| 2 | Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep in any type of soil, for foundation etc., or for laying of cable/ GI Pipe, shafts, wells, cesspits, manholes, pier holes, etc., complete all as specified. |
| 3 | M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, filling, mass concrete etc., complete all as specified and as directed. |
| 4 | M&L for Reinforced Cement Concrete M–25 (Design Mix) with admixtures, as in Foundations including Rafts, Footings, Foundation Beams, Plinth Beams, Bases for Columns etc., complete all as specified and as directed. |
| 5 | M&L for Reinforced Cement Concrete M–25 (Design Mix) with admixtures, as in Columns, Pillars, Piers, Posts & Struts etc., complete all as specified and as directed. |
| 6 | M&L for Reinforced Cement Concrete M–25 (Design Mix) with admixtures, as in floor beams, roof beams, cantilevers, bressumers, middle beams, lintels over 1.5m span and lintel bands etc., complete all as specified and as directed. |
| 7 | Steel formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete, complete all as specified and as directed. |
| 8 | Steel formwork to sides and soffits of floor or roof beams, cantilevers, bressummers, lintels, shelves, lintel beams, RCC bands, complete all as specified. |
| 9 | Steel formwork to sides of pillars, posts, struts, columns, stanchions and the like, for fair finished surfaces of concrete, complete all as specified and as directed. |
| 10 | M&L for Reinforcement using TMT bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. |
| 11 | M&L for Reinforcement using TMT bars of Grade Fe-500D of 8mm dia and over upto and including 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welded complete all as specified. |
| 12 | M&L for Pre-cast cement concrete solid block masonary type C1, 1:3:6 (using 20 mm graded stone aggregate) exc 10 cm width and setting in CM 1:6, complete all as specified and as directed. |
| 13 | M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even and fair without using extra cement, complete all as specified and as directed. |
| 14 | M&L for 15mm thick Rendering on fair faces of brick work or concrete surfaces in two layers as 10mm thick in cement mortar 1:6 followed by 5mm thick in cement mortar 1:4 with and including mixed with water proofing compound @2% of weight of cement and finish the surface even and smooth without using extra cement, complete all as specified and as directed. Note: Quoted rate shall be inclusive of water proofing compound. |
| 15 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil, as in any type of soil, complete all as specified. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. |
| 16 | Removal of excavated material [Soil] to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified. |
| 17 | Excavating in post holes (or similar holes), as in soft/loose soil, each not exceeding 0.5cum, getting out , returning ,filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m where directed and making good surfaces, complete all as specified and as directed. |
| 18 | M&L for Hardcore of gauge not exc. 63mm, broken stone or boulders, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface, complete all as specified and as directed. |
| 19 | M&L for 100mm thick PCC 1:3:6 type C2 (using 40mm graded granite stone aggregate) as in sub base, complete all as specified and as directed. |
| 20 | M&L for Premium quality, joint free coloured Non skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exc. 0.11 Sq.m. but n. exc. 0.18Sq.m, as in floors etc., laid over and including 15mm thick screed bed or bedding layer in CM (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified and directed. |
| 21 | M&L for Providing 25mm thick (measured solid) Precast RCC Jallies 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in louvers and jallies and similar articles set in CM 1:4, finished plain fair faces, including necessary all mouldings, formwork etc., with and including demolition of existing u/s precast RCC jallies of any type, complete all as specified and as directed. Note: Necessary reinforcement shall be measured and paid separately. |
| 22 | S&F Machine cut Granite stone 18-20mm thick (Z Black), table rubbed & polished, as in skirting, dado, steps, window cills, cooking platform and the like, laid over and including 20mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, rubbing and polishing, complete all as specifed and as directed. |
| 23 | M&L for Factory made Machine pressed pre-cast concrete interlocking paver block any shape and size with glossy finish on top, confirming to IS 15658-2006 of 80mm thick, M-40 grade with grey cement and no pigment, with and including 50mm thick river sand cushion under interlocking paver block with watering and consolidation, with and including demolition of existing floor tiles of any type, complete all as specified and directed by the Engineer-in-Charge. |
| 24 | M&L for Rolled Mild steel as in roof trusses (Framed) trussed purlins, rafters, struts (beam, tee, angle channel, hollow or flat sections ) including distance pieces, cleats etc., conforming to grade Fe 410-W Gde E - 250 quality \"A\", complete all as specified and as directed. |
| 25 | M&L Framed work such as grills, gratings, rungs etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladder, framed baluster, walk ways, railings, and similar work confirming to Gde Fe-290 Gde E-165, complete all as specified and as directed. |
| 26 | M&L for Mild steel work as in Posts, tubular trusses with and including special shaped washers using ERW or induction butt welding confirming to IS 1161-1979, grade St-240, complete all as specified and as directed. |
| 27 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (TFT) of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed. |
| 28 | S&F Mild Steel Corrugated Galvanised Steel Sheet 0.45mm thick of class 8, grade of zinc coating 275, as in roof covering with two corrugation side laps fixed with coach screws & washers, complete all as specified and as directed. |
| 29 | S&F Mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted orwelded attachment etc., confirming to Gde Fe 290(Gde-E-165), complete all as specified and as directed. |
| 30 | M&L for Preparation of new or previously untreated surfaces of steel or steel based surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. Note: Quoted rate shall be inclusive of necessary scaffolding/shoring and other safety measures to be undertaken during execution of work. |
| 31 | M&L for Applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, with and including preparation of new surfaces of wall, complete all as specified and as directed. |
| 32 | M&Lfor Cement concrete roofing tiles, rustic red colour, 420mm x 330mm size of 230 kg minimum breaking strength, double groove design, as in roofing, interlocking at side joints, laid dry as in roofing, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
| 33 | M&L for Cement concrete Rusted Red/Grey colour Ridge cap of size 360mmx207mm x 240mm, with and including 15mm thick in roofing bedded and jointed in cement mortar 1:6, complete all as specified and as directed. Make: Model INDOGRACE of ETERNA or Equivalent make as specified here in after. |
