|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: |
| 2 | 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 3 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 4 | Sal wood |
| 5 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 6 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 7 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer\"s specification and direction of Engineer- in-charge. |
| 8 | Extruded section profile size 42x50 mm |
| 9 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds |
| 10 | Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body : Using R4 series with frame (115 mm & above) x (45 mm & above) & both glazed and fly screen sash (44 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi- point locking system. (Height above 1.8m) |
| 11 | Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete. |
| 12 | Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete. |
| 13 | Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete. |
| 14 | Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete. |
| 15 | Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 16 | Size of Tile 600x600 mm |
| 17 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, difusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 18 | 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks) |
| 19 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. and dispsal of malba to the dumping ground notified by MCD Delhi within any lead complete. |
| 20 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba to the dumping ground notified by MCD Delhi within any lead all complete as per directions of Engineer-in-Charge. |
| 21 | Demolishing cement concrete manually/ by mechanical means including disposal of material to the dumping ground notified by MCD Delhi within any lead as per direction of Engineer - in - charge. |
| 22 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 23 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking serviceable material within 50 metres lead and disposal of unserviceable material to the dumping ground notified by MCD Delhi within any lead.: |
| 24 | Of area 3 sq. metres and below |
| 25 | Dismantling tile work in floors and roofs laid in cement mortar including stacking useable material within 50 metres lead and disposal of malba to the dumping ground notified by MCD Delhi within any lead. |
| 26 | For thickness of tiles 10 mm to 25 mm |
| 27 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 28 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 29 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 30 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 31 | Flexible pipe : 32 mm dia |
| 32 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 34 | 15 mm nominal dia Pipes |
| 35 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 36 | 45 cm length : 15 mm nominal bore |
| 37 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 38 | 15 mm nominal bore |
| 39 | Providing and fixing PTMT grating of approved quality and colour. |
| 40 | Circular type : 100 mm nominal dia |
| 41 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 42 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 43 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 44 | Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120 gram per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. |
| 45 | With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles. |
| 46 | Supplying of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete as per manufacturer\"s specification etc. all complete as per direction of Engineer-in-charge. |
| 47 | Supplying of water thinnable cement primer having VOC content less than 50 gram/litre of approved manufacturer all complete as per manufacturer\"s specification etc. all complete as per direction of Engineer-in-charge. |
| 48 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre (Labour Rate only excluding the cost of material). |
| 49 | Supplying of white cement based putty of approved brand and manufacturer as per manufacturer\"s specification etc. all complete as per direction of Engineer-in-charge. |
| 50 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (Labour Rate only excluding the cost of material). |
| 51 | Providing and fixing 15mm nominal bore C.P. 2-Way Angular Stop Cock with Wall Flange of make Prayag (Category no. PIS-11H) or equivalent make as per approved list of materials etc. all complete as per direction of Engineer-in-charge. |
| 52 | Providing and fixing Hand Shower (Health Faucet) with 1 Meter Long Easy Flex Tube in Chrome Finish & Wall Hook of Jaquar (Category No. ALD-565) or equivalent make as per approved list of materials etc. all complete as per direction of Engineer-in-charge. |
| 53 | Providing and fixing PVC trap of size 100/110mm self cleansing design with or without vent arm complete, including cost of cutting and making good the walls and floors etc. all complete as per direction of Engineer-in-charge. |
| 54 | Providing and fixing zebra blind S.Sopage/Vienna Pearl with head rail. The drive unit shall be of clutch for quick easy safe installation, moulded plastic with steal spring support and inserted into the left side. The end plug shall be moulded plastic with steal location in the plug shall be inserted into tube and the support bracket shall be projected outside max of 80mm the roller tube should be extruded aluminium anodized 15 micron, 32-40 mm dia with 1 mm thickness. The bottom rail shall be offlat/around made upto powder coated mild steel with 30 micron powder coated. The ball chain shall be endless beaded balls etc. complete as per direction of Engineer-in-charge. (The supply of material by the contractor shall be certified by the company with proper warranty certificate approved brands VISTA, HUNTER DOUGLAS & D DÉCOR, etc). |
| 55 | Providing & fixing 12mm thick AC5 grade laminated wooden flooring of Action Tesa, Pergo, Armstrong or equivalent made from high density fibre board having density 900 kg/m³ or more, core board based of dome technology in 12mm thickness, made from lignocellulose material-specifically “plantation timbers” like eucalyptus manufactured with homogeneous core, the flooring shall be tropicalized with an anti-bacterial surface with dimensional stability and laminated with melamine formaldehyde impregnated European made décor paper (70-120gsm) duly overplayed with an anti-abrasion layer of aluminium oxide impregnated tissue (55,65,85 gsm) in AC5 6500 abrasion cycle ) plank size 193 x 1214. the product shall have an isometric locking profile made from a 5 spindled profiling head. the locking profile shall be wax coated to prevent moisture seepage. the laminate flooring shall to be fixed on a base of 2mm thick layer of PU foam having a density of 24kg/m³. the bare floor shall be 1st covered with PE sheet having a thickness of 0.2mm as per direction of Engineer-in-charge. |
| 56 | Providing and fixing 12mm Thick plain HDHMR board of Action Tesa, Green Ply, Marino or equivalent make in position with concealed G.I. section and with suitable screw and fixing arrangement for wall panelling using board of required thickness fixed on the \"W\" profile (0.55 mm thick) having a knurled web of 51.55 mm and two flanges of 26 mm each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter channel having one flange of 20 mm and another flange of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C with fully threaded self-tapping dry wall screws. Board is fixed to the \"W\" profile with 25 mm countersunk ribbed head screws @ 200 mm C/C., all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish as per direction of Engineers - in- charge. |
| 57 | Providing and fixing wooden wall laminate of Action Tesa / Pergo or equivalent make AC-3 or above of (panel size 1214 x 193 x 8.0 mm) of required colour and shade with double click locking system including all necessary accessories, all types beadings, headless nails where ever required etc. on HDHMR board/wooden board (HDHMR board / wooden board shall be paid separately) complete as per direction of Engineer in charge. |
| 58 | Providing and fixing digital Joint free glazed wall tiles (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 59 | Credit and disposal of old damaged and dismantled Steel/Iron/M.S/G.I and other similar articles (The material will be the property of contractor)Note: Actual weight of the material to be measured for payment. |
| 60 | Credit to the work for dismantled material received during execution of work at site: (a) Unserviceable flush/PVC/Wooden doors shutters.Note: Actual quantity of the material to be measured for payment. |
| 61 | Providing & Placing of Office Table of Size 1500mm (L1) x 600mm (D1) x 750mm (H1) with following details and specification :- The top is made of 36mm thick E1 grade MDF Board (Environmental Friendly), Edge banding (PVC) 2mm. E1 grade MDF with zero urea, for better inhouse quality. This should comply with (EN 120-1992). Epoxy powder coated spray color, baked at temperature 200 C°. Below the access flap, Top supported on One side Gable end 25mm thick MDF Board. This should comply with (EN 120-1992). The product is ensuring compliance with industry standards. It comes with a 7-year warranty, reflecting its quality and durability. All specifications are completed as per the direction of Engineer-in- Charge. |
| 62 | Providing & Placing of Side Unit of Size 1000mm (L1) x 600mm (D1) x 670 mm (H1) with following details and specification :- whose top is made of 36 mm thick E1 grade. Top supported on One side suspended side combo storage made out 19 mm thick (E1 Grade) MDF board, Side Combo Storage is combination of 2 nos swing shutter & Open space, E1 grade MDF to be used hich provide no urea formaldehyde emission and formaldehyde, It comes with 7-year warranty, reflecting its quality and durability. All specifications are completed as per the manufacturer\"s guidelines, approved samples, and the direction of the Engineer-in- Charge. |
| 63 | Providing and Placing of pedestal unit with three Drawer (2Box+1 File) with levelers. The pedestal / drawers unit shall have outer Dimensions of 600 mm Height x 400 mm Width x 450 mm Depth. The pedestal unit connecting with 19mm thick MDF modesty panel with matching finish cover Edge banding (PVC). E1 grade Veneer MDF with zero urea formaldehyde emissions ( |
| 64 | Providing & Placing Oval shape Conference Table of size 2200x1200x670 mm in Well- Shape with Top and Legs are made of 36 mm thick MDF (E-1 Grade), finish with matching 2 mm PVC edge-banding. The Modesty panel is made of MDF board Grade E 1 (Environmental Friendly) of thickness 18 mm MDF with Edge Banding (PVC) 2 mm. Wire management: Completely concealed wire management with Aluminium anodized flipper with soft closure, The meeting table can be Convexed or Oval shaped. E1 Grade laminate to be used which provide no urea. This should comply with (EN 120-1892). The product is ensuring compliance with industry standards. It comes with a 7-year warranty, reflecting its quality and durability. All specifications are completed as per the manufacturer\"s guidelines, approved samples, and the direction of the Engineer-in Charge. |
| 65 | Supplying and Placing in position Main High back Chair with following specification :- seat made up of insert moulded Polyurethane Foam upholstered with foam laminated mesh fabric, insert moulded foam assembled over a load bearing plastic seat cover, back is made up of two piece injection moulded frame, inner frame upholstered with mesh fabric and mounted on the main assembly, back adjustable lumbar support for achieving comfortable seating posture, seat size 44.5 - 52.5 cm depth (approx.), 46.4 - 51.0 cm width (approx.), sub assembly back size 55.5 cm- 62 cm height. (approx.), effective back height from Seat - 57 cm (approx.), polyurethane foam for seat having density 65±4 kg/m3, armrest top injection moulded in polyurethane and mounted on the injection moulded height adjustable type armrest, arm rest height adjustable up to 4.5 cm (approx) in 3 steps & width movement adjustable, 360 degree revolving type mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3 position locking with antishock feature, pneumatic height adjustment of 8.5 cm spine bracket made of aluminum die cast piece connecting to back with mechanism, pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors (castor wheel dia. 6.0 cm approx.), base pedestal dia 65.0cm (approx.) and pitch center dia. 71.0 cm with castors, twin wheel castors injection moulded in Nylon etc. The product is ensuring compliance with industry standards. It comes with a 7-year warranty, reflecting its quality and durability. All specifications are completed as per the manufacturer\"s guidelines, approved samples, and the direction of the Executive Engineer-in-Charge. |
| 66 | Providing and Placing of Mid Back Chair with cushioned seat and mesh back assembly, moulded plywood upholstered with moulded polyurethane foam & finished with Leatherite seat. Back size: (W) 450 - 500 mm (H) 550-580mm; Seat size: (L) 450mm - 500mm (W) 450 - 500mm with Polyurethane Foam. Polyurethane Foam: The polyurethane foam (Recyclable) of minimum density = 30 kg/ cum + 2 kg/cum fixed to moulded plywood and upholstered with Leathrite. Synchro mechanism: 360 degree revolving type, from pivot for tilt with multiple locking position & feet resting on ground for extra comfort. The pneumatic adjustment has an adjustment stroke of 70-120 mm, Pedestal Assembly: should have 5 star aluminium die cast with hard castors sutable for tiles flooring with adjustment, twin wheel castors & the pitch centre Dia is 650 +/- 50mm. (750 +/- 10mm with castors). Twin wheel castors: these are made of injection moulded in black PP having 50-60mm dia, complete in all respect. The above chair should be finished / completed as per above mentioned specifications including providing and fixing of other related materials including hardwares, etc. complete or as directed by the Engineer-in Charge The chair having back curvature in longitudinal and in trasverse direction. It comes with a 7-year warranty, reflecting its quality and durability. All complete as per manufacturers specification. All specifications are completed as per the the direction of the Engineer-in- Charge. |
| 67 | Providing & Placing two seater sofa with dimension overall width =1200±10 mm, overall depth = 770±10 mm & overall height = 780±10 mm. : Seating Height 425mm, Wooden structure of sofa to be fabricated using good quality hardwood duly seasoned and applying anti-termite paint of approved brand & manufacture to ensure stability of the frame, On the wooden base frame of the sofa to be provided with M.S. helical spring, sides & back with jute strips, with polyfill covered with jute & finished with thick marking cloth before doing final finished with leathrite have basic cost not less than 1000/- Pet Mt. Seat - 40-45Kg/cum density PU Foam, Back - 35-40Kg/cum density PU foam, 60mm thick, Sides (inside) - 40-45 Kg/cum density PU Foam, 45 mm thick Sides (outside) & back (back side) - 35-40 Kgcum density PU foam, 25mm thick. Seat shall rest on SS square frame of size 25mm x 25mm supported solid wooden section of height 225mm. All SS work should be in grade 304. Base of sofa should be infilled with suitable woode sections so as to give proper support to the seat. Height of the base of sofa shall be 200-250mm(approx). Finished width of arm shall be 100mm after upholstery work. It comes with a 7-year warranty, reflecting its quality and durability. All specifications are completed as per the approved samples, and the direction of the Engineer in- Charge. Please Enable Macros to View BoQ information |
