Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near out let of RWP and OHT staging area or specifically ordered by Engineer-in-Charge in writing complete all as specified and directed. |
| 2 | Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified. |
| 3 | Removing mud phuska/soil material exc.250 m but n exc. 500 m and depositing where directed. |
| 4 | M&L for brushing neat cement slurry with 3 kg of cement per square metre complete all as specified and directed. |
| 5 | M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified and directed. |
| 6 | Supply only water proofing compound complete all as specified and directed. |
| 7 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric(wt. not less than 150 gms/sqm) land on primed surface by torced apllication complete all as specified and directed. |
| 8 | Supply and fixing Heat Resistant Terrace Tiles(300mmx300mmx20mm) with SRI(solar refractive index)>78,solar reflection>0.70 and initial emittance>0.75 on waterproof and sloped surface of terrace, laid over and including 20mm thick cement sand mortar in the ratio of 1:4(1 cement:4coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1,including rubbing and polishing of the surface upto 3 cuts complete,includingproviding skirting upto 150mm height along the parapet walls in the same manner complete all as specified and directed. |
| 9 | M & L Plain Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate min radius of 75mm thick as in roof and parapet wall junction, roof benching, kerbs, mud stop, coping, rounded or chamfered on edges, incl necessary slopingon roofincluding form work complete all as specified. |
| 10 | Excavation in trenches width n\"exc 1.5 m and not exceeding 1.5m deep and getting out in soft / loose soil all as specified and directed.Note:-Insurance of workmen & cleaning of site, removal of all hinderance\"s/obstractions unforseen item, Electric cable, Gas Pipe line etc permisssion from other department should be responsibility of contractor (MES will only assist in getting permission etc) restoring and getting the same constructed/Repaired/Replacement complete & nothing extra shall be payable. |
| 11 | M&L for PCC 1:3:6 type C-2, (using 40mm graded stone aggregate)as in surface channels and drains incl all moulds and forms all as spd and directed. |
| 12 | Extra forming fair finished drain or channel inner girth n.exc 30 CMin cement, concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 13 | M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size burnt bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified. |
| 14 | M&L for15mm thick rendering on concrete surface/brick surface in cement mortar 1:4 surface finished even and fair mi complete all as specified and as directed. |
| 15 | S&F factory made 75mm thick SFRC manhole/ Drain covers with frame (heavy duty) HD-20 graded designation, confirming to IS-12592, area not exc. 0.50 Sqm each, fixed in cement concrete 1:2:4 using 20mm graded stone aggregate complete all as specified and directed. |
| 16 | Taking down door/window/ventilator frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed. |
| 17 | M&Lfor Cutting holes in brick walls in cement mortar for inserting hold fast and similar works etc. and making good to dismentalled portion in CM 1:3 or cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in wall exc half brick but n exc one brick thick complete all as specifiedand as directed. |
| 18 | S&F Aluminium door single leaf with powder coated aluminium frame of section 62.5x37x1.5mm thick, shutter with bottom & middle rail of section 112.50x 37x1.5mm thick and styles & top rail of section 83x37x1.5mm thick with centrally locking arrangement with lock make of ‘GODREJ’ or ‘LINK’ 7 lever and self closing device with rebate includingjointingcleats, fixing of builders hardware fittings, necessary numbers of floor spring and glazing/gauge with 5mm thick glass includingnecessary fittings, fixtures & aluminium snap beads, complete all as specified and directed. |
| 19 | Taking down door/window/ventilator frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified. |
| 20 | S&F for powder coating (minimum thickness of powder coating 50 micron) aluminium three track window, shutter (Size 45X15mm) i.e. two shutter with 4.8mm thick tinted glass and one with stainless steel wire cloth of 0.36mm diaand avg width of apperture 1.4mm and sliding section complete window size (92x45.5mm) with frame (Chowkhat) size (101.60x44.45x1.90mm thick), including all necessary locking arrangement (touch lock of zinc alloyed powder coated as per sample)and fittings complete all as specified and directed. |
| 21 | S&F for powder coating aluminium ventilator, openable, (top hung and bottom fixed type) without sash bar with aluminium section of weight 0.55/RM including glazing, necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, hook & eye minium one no on each shutter(for top hung shutter), one no aluminium tower bolt 100mm long and 75mm long aluminium handle in each shutter etc. complete all as specified and as directed.Note:- glazing wiremesh shall be measured and paid separately. |
| 22 | S&F 4mm thick Figured glass, pin head type and glazing with oil putty in sqm n exc 0.5 sqm in each pane fixed in bottom two pane in windows etc complete all as specified and directed. |
| 23 | S&F galvanised mild steel wire cloth 0.56 mm nominal dia or wire and an average width aparture 1.18 mm and fixed with tinned tack or stainless steel wire staple complete all as specified and directed. |
| 24 | S&F Solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheetreinforced with MS square tube supplying and fixing as per specification complete all as specified and directed. |
| 25 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck insidesolvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail either side & as gap insert for top rail and bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 26 | S&F 100mm butt hinges medium weight cold rolled fixed to doors with SS screws complete all as specified and directed. |
| 27 | S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed. |
| 28 | S&F 125mm long aluminium handles cast type anodised ISI Marked complete all as specified and directed. |
| 29 | Demoltion ofbrick work built in cement mortar of any specification and in any position complete all as specified. |
| 30 | Taking down of cement mortar plaster of any description and preparation of surfaces for receiving new plaster including racking out of joints complete all as specified. |
| 31 | M&L for 10mm thick rendering with cement mortar 1:6 on brick work or concrete surfaces on wall, finish the surface even and smooth without using extra cement complete all as specified and directed. |
| 32 | M&L for 5mm thick rendering in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified. |
| 33 | M&L for Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over and including a coat of chalk whiting,on plastered surfaces,preparatory to distempering after finishing wall surface with 1mm thick wall care putty complete all as specified. |
| 34 | M&L for preparation of old decorated plastered surfaces of walls etc by complete removal of existing treatment including washing, rubbing down and stopping of surface and applying two coats of oil emulsion distemper over and including a coat of primer on wall surfaces complete all as specifiedand dircted. |
| 35 | M&L for Preparationof newly plastered surfaces of ceiling& applying three coats of white washcomplete all as specified. |
| 36 | M&L preparation old plastered surfaces of ceiling and applying one coats of white wash all as specified and directed. |
| 37 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm includingpreparation of old plastered surfacesetc., complete all as specified and directed. |
| 38 | Dismantling of floor hearth and wall tiling incl mortar beding and throw rubbish out the premises as directed by the Engr-in-Charge. |
| 39 | M&L for light shade Virified Ceramic tiles 09 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including cement screed bed 15mm thick in cement mortar (1:4) complete all as specified and as direcetd. |
| 40 | M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchlaid over and including cement screed bed 15mm thick in cement mortar (1:4) complete all as specified and directed. |
| 41 | M&LGlazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 6 to 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement on vertical surfaces of walls such as skirting dado etc laid over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed. |
| 42 | Demolition of reinforced cement concreteas in Chajja, RCC parapet, Kitchen slab, Chullah hood, chimney portion and similar work concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 43 | M&L Formwork to soffits of suspended slabs such as kitchen slabs, floor slabs, landings and similar work; not exceeding200mm thick (Horizontal or sloping) flat rough finished surfaces of concerete all as specified and directed. |
| 44 | M&L for reinforced cement concrete Nominal Mix using type B-1, 1:2:4 (20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and the like concerete all as specified and directed. (Note :-Steel reinforcement bars shall be measured and paid separately under relevant items) |
| 45 | M&L for mild steel TMT bars upto 10mm dia and over cut to length,bent to shape required including cranking, biniding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 46 | M&L Granite 18 to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over & including 15mm thick screed in cement mortar (1:4) with pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified. |
| 47 | Demolition of unreinforced cement concrete in ground floor and pavings n.exc. 15 cm thick (below or above GL) complete all as specified and directed by Engineer in Charge |
| 48 | M&L for 750mm wide, 75mm thick cement concrete 1:3:6 (Nominal mix) with 40mm crushed stone aggregate finished even and fair, laid to slope of 1 in 12. it shall be laid in alternate bays, each bay not exceeding 3m length with joint to be filled with bituminious mastic filing comprising a mixture of 1 part of heated hot blown bitumen 85/25 penetration and two parts of heated sand. the toe of plinth protection of size 75mm deep, complete all as specified and directed. |
| 49 | S&F in repair 15mm dia brass chromium plated centre hole mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including connection pipe and fittingscomplete all as specified and directed. |
| 50 | S& F in repair Bib tap of cast copper alloy brass but fancy type, Chromium plated 15mm bore, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrulecomplete all as specified and directed. |
| 51 | S&F in repair 1000 litres capacity rotational moulded, triple layer polyethylene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in positionon roof including fittings complete all as specified and directed by Engineer in Charge. |
| 52 | S&F in repair Gun-metal, globe or gate valves 20mm dia bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 53 | S&F in repair 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 gms) and fixed complete all as specified and directed by Engr-in-Charge. |
| 54 | S&F 600x450 mm beveled edge looking mirror of selected quality glass and backing with 6mm thick AC building board and fixed to wall with PVC rawl plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr-in-Charge. |
| 55 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 56 | M&L Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified. |
| 57 | S&F in repair 15mm bore stop/angle valve cast copper alloy with crutch or butterflty handle, screwed down screwed high pressure for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup complete all as specified and directed by Engr-in-Charge. |
| 58 | S&F PVC Connection pipe, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipecomplete all as specified. |
| 59 | S&F in repair Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F Sink made of stainless steel 1.0 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 61 | S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cementcomplete all as specified and directed by Engr-in-Charge. |
| 62 | S&F in repair 110mm bore PVC (SWR) pipe of pressure not less than 4kg/sqcm in single socketed, in any length withrubber ring joints,fixed to wall including distance pieces and stack clamp with nuts and bolts complete all as specified and as directed. |
| 63 | S&F 110mm bore, PVC (SWR) bends any radius ccomplete all as specified and directed. |
| 64 | S&F in repair 75mm bore PVC(SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed. |
| 65 | S&F 75mm bore PVC(SWR) bends any radius complete all as specified and directed. |
| 66 | S&F 110mm bore PVC (SWR) \"S\" trap complete all as specified and as directed. |
| 67 | Supply and laying 20mm outer dia of CPVC pipe SDR11 fittings in trenches, wall and ceiling including fittings including taking down old steel tubing etc complete all as specified and directed. |
| 68 | Supply and laying 25mm outer dia of CPVC pipe SDR11 fittings in trenches, wall and ceiling including fittings etc including taking down old steel tubing complete all as specified and directed. |
| 69 | S&F 20mm CPVC brass elbow completeall as specified and directed . |
| 70 | S&F 25mm CPVC brass elbow completeall as specified and directed . |
| 71 | S&F 20mm CPVC brass elbow (3/4 x 1.2)completeall as specified and directed. |
| 72 | S&F 20mm CPVC Tee completeall as specified and directed. |
| 73 | S&F25mm CPVC Tee completeall as specified and directed. |
| 74 | S&F stainless steel plate rack made of 0.80mm thick sheet of size 750x750x250mm fixed to wall with suitable rawl plug complete all as specified and directed. |
| 75 | S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nosper RM and fixed withPVC rawl plugs & steel screwscomplete all as specified and directed. |
| 76 | Providing & fixing false ceiling at heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. |
| 77 | M&L for 40mm lnsulated PVC Wall Lining consisting of PVC Insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specified and as directeed. |
| 78 | M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as specified and as direcetd. |
| 79 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in soft loose soil complete all as specified and as directed. |
| 80 | M& L for cement concrete in foundation filling and mass concrete type C2 1:3:6 (40mm graded crushed stone aggregate) complete all as specified and as directed. |
| 81 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft loose soil complete all as specified and as directed. |
| 82 | Returning, filling in including spreading leveling, watering and wellramming in layers not exceeding 25 cm of soft/loose complete all as specified and as directed. |
| 83 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point in soil complete all as specified and as directed. |
| 84 | M&L for Hardcore of broken stone guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and as directed. |
| 85 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed. |
| 86 | M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in sub base flooring complete all as specified and as directed. |
| 87 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 88 | M&L for Coloured Machine pressed cement concrete chequered tiles 30cm X 30cm X 20 mm thick machine pressed; set jointed and pointed in neat cement slurry in floors and cut and pointed with white cement and pigment over and including 15mm thick screed bedding layer in CM 1:6 including demolition of old chequered tiles all as specified and as directed. |
| 89 | M&L for cement concrete Type B-1, 1:2:4 (using 20mm graded crushed stone agg) in copings, kneelers, apex stones, bed plates, kerbs and the like incl weathering, slightly rounded or chamfered angles and throating, complete all as specified & directed . |
| 90 | S&F Rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed. |
| 91 | S&F of Fe 410-W(Gde-E-250) quality-A mild steel plates, plain or chequered , 5mm thick or over in thickness in available sizes complete all as specified & directed. |
| 92 | S&F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of green colour as approved by GE having tensile strength of 550Mpa as in roof covering, ridge, fixed with self tapping screws complete all as spd & directed. |
| 93 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 94 | Designing providing and fixing 4mm thick Aluminium composite claddingover RCC/BRICK surfaces either segmental/straight in plan wherever specified with extruded aluminium u sections ,angles,cleats ,weather sealants, backer rods of required size stainless steel screws, rivets , brackets, drilling and fixing the cladding to either masonary or reinforced cement concrete including frame work as required and as per manufacturer\"s instructions, complete the work in all respect including all necessary accessories. At all soffits aluminium cladding shall be bend 90 degree and joints at corner or edges will not be acceptable on horizontal surface, the size also converted the shape in awning to the face as approved desiged complete all as per manufacturer\"s specifications and as directed. |
| 95 | M&L for 12 mm thick 100% Solid WPC (Wood Polymer Composite) Laminated Board of required size as in frames, wardbobs, shutter, CBs etc comprising of virgin PVC resin of K Valve 57-60 (Suspension Grade),Calcium Carbonate and natural fibers ( Wood powders/rice husk/Wheat husk) and non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with having minimum density not less than 650 kg/cbm having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of spread of flame of Class A category with property of being Termite/Borer Free, Water/Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of board including fixing with screws/fastner/clamps etc. as requuired to make CBs/wardrobs etccomplete all as per specified and directed. |
| 96 | M&L for 12 mm thick 100% Solid WPC (Wood Polymer Composite) Plain Board of required size comprising of virgin PVC resin of K Valve 57-60 (Suspension Grade),Calcium Carbonate and natural fibers ( Wood powders/rice husk/Wheat husk) and non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbm having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of spread of flame of Class A category with property of being Termite/Borer Free, Water/Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of board including fixing with screws/fastner/clamps etc. as requuired to make CBs/wardrobs etc complete all as per specified and directed. |
| 97 | S&F of stainless steel handles 100 mm sizefor kitchen cabinet shutters complete all as per specified and directed. |
| 98 | S&F of Stainless steel soft auto closing hinges openable at 0 degree for kitchen cabinet shutters complete all as per specified and directed. |
| 99 | S & F ofchrome plated stainless steel wire basket (storage / Plain basket) pull out type, size 380 x 500 mm with necessary fixing clips etc. complete all as per specified and directed. |
| 100 | S & F ofchrome plated telescopic channelsize 450mmx20mmx1.5mmwith necessary fixing clips etc. complete all as per specified and directed. |
| 101 | PMM repairs (FOR PATCH REPAIRS):-PMM repairs shall be done as per following methodology i)Chipping of plaster and unsound/weak concrete material till reinforcement bars are exposed, which enable their rust removal vides item ii) below,from slabs, beams, and columns etc. with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-incharge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris upfor all lifts and leads.ii) ) Rust removal by Providing and applying Fosroc Reebaklens RR or equivalnet from SIKA/ BASF,a combination of acid based material, corrosion inhibitors and dispersing agents rust remover, forremoval of all rust/ scales/corrosion from reinforcement bars before microconcreting or patch repair,It Shall be appliedwith brush for complete wetting of rusted metal surface at coverage of 2- 2.5 Sqm/ltr. &allow itto reactfor 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal /steel for about 5-7 days. Before applying any protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth.iii)Anticorrosive treatment by Providing and applying Nitozinc Primer an epoxy based zinc rich anti corrosive primer having adhesive bond strength ≥ 1.5 MPa as per ASTM D4541, & shall comply to per ASTM B-117 to be applied on well cleaned, fully exposed and all loose scale , rust free surface obtained by grit blasting or suitable means ,to be done with coverage @4.5sqm/litres to achieve a minimum thickness of 40microns DFT or as per direction of Engineer-In charge. |
| 102 | iv) Epoxy bonding for Old concrete & New concrete by providing and applying bond coat on the prepared surface with two component epoxy based bonding coat Nitobond EP of Fosroc make or equivalent, having specific gravity 1.15 to 1.2 gm/cc, Compressive strength(BS 6319 Pt.2)- 50 Mpa at 7 days, Flexural strength strength(BS 6319 Pt.3)- 35 Mpa at 7 days, Tensile strength (BS 6319 Pt.7)- 20 Mpa at 7 days, Shear Strength (BS 6319 Pt.4)- 10 Mpa at 7 days, having an over lay time of 6 hrs and 30̊C. Bonding agent shall have coverage not less than 2.5sqm/litresLaying of reinstatement polymer modified mortar or micro concrete shall be completed within the overlay time of bonding coat.Item rate is inclusive of materials all labour, tools and tackles. complete as per specification and as directed by Engg.-in-charge.v) PMM by providing and laying single component, polymer modified, fibre reinforced cementitious repair mortar,Rendroc SP40 or equivalent from SIKA/BASF over the tacky bond coat, that achieves Compressive strength (BS 1881 Pt.116) > 20 MPa at 1 day ,> 45 Mpa at 28 days, Tensile Strength > 2.5MPa, Flexural Strength> 7Mpa at 28 days,Finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slabs, piles etc., complete in all aspect as per manufactur\"s methodology. Rates include cost of all labour, materials, Tools and Plants,propping, scaffolding, shuettering, safety arrangment, quality control, testing complete as per specifications and direction of engineer in charge. |
| 103 | vi) Item rates of PMM 25 mm and PMM 50 mm (against items (a) and (b) respectively ) are inclusive of all materials, labour, tools and plants, propping, scaffolding, safety arrangement, quality control, testing and all items of works from i) to v) abovequality controletc. complete in all respect, as per specifications and as directed by Engg.-in-charge.Work shall be complete only after proper wet curing has been done by contractor and surface has beenevaluated for satisfactory quality by sounding/tapping with a blunt metal instrument, and testing of PMM cubes filled up and cured by contractor during the application of PMM (75mm size cube crushing strength at the end of 28-day to be not less than 45 N/sqmm) in addition to NDT Testing as per under item of \"Testing of works\" |
| 104 | 25-30 mm average thickness( in 2 layers) up to 3.5mtr height |
| 105 | 50-60 mm average thickness ( in 3 layers ) up to 3.5mtr height |
| 106 | M&L for cement concrete Type E-2, 1:5:10 (using 40mm graded crushed stone agg) in foundation, filling and mass concrete complete all as spd & directed by Engr-in-Charge. |
| 107 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:6 complete all as spd & directed by Engr-in-Charge. |
| 108 | M&L preparation of newly plastered surfacesand applying two coats of cement base paint over and including a coat of alkali resistance primer on external surfaces of walls complete all as specified and directed. |
| 109 | M&L for 50 mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring complete all as specified and as directed. |
| 110 | S&F rolled mild steel workin Steel work in tubular trussesincluding special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed. |
| 111 | M&L for preparation of new steel & iron surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as spd & directed. |
| 112 | Taking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets,regulators light fittings) and removal from site and making good the disturbed surfaces of (wall/floors/ceiling etc) complete all as specfied & directed. |
| 113 | M&L for concealed point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded copper conductor drawn through and including non-metalic rigid PVC conduit medium grade ISI Marked and all conduit accessories concealed in wall/fixed to roof/truss/columns etc and including provision of 1.5 sqmm PVC insulated single core copper cable FRLS as earth continuity conductor, fabricated branded modular metal flush box duly make embossed, concealed in walls with suitable modular inner and outer plate for housing modular switches, socket outlet and fan regulators etc. all as specified and directed :- |
| 114 | (a) One light/fan/bell/Exhaust fan/Fresh Air Fan point controlled by one way switch 5 amps. |
| 115 | (b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board. |
| 116 | (c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board along with other switches. |
| 117 | All as per item No 115 above but with single core copper conductor cable FLRS 2.50 sqmm for one 3 pinAC Box outlet,20 Amps concealed and including provision of 2.50 Sqmm PVC insulated single core copper conductor cable as earth continuity conductor on independent board. |
| 118 | M&L for concealed point wiring with insulated unsheathed multistranded FRLS copper conductor in non-metalic rigidPVC conduit but with single core copper conductor cable FLRS 4.0 sqmm for one 3 pin AC Box outlet 20 Amps concealed and including provision of 4.0 Sqmm single core PVC insulatedcopper conductor cable as earth continuity conductor on independent board.(For AC point) |
| 119 | S&F Modular switch 1 way 6A,1 module, 230V, 50 Hz complete all asspecified and directed. |
| 120 | S&F Modular switch 1 way 16A,1 module, 230V, 50 Hz complete all asspecified and directed. |
| 121 | S&F Modular socket 6A- 3 pin combined 2 module,230V, 50 Hz complete all as specified and directed. |
| 122 | S&F Modular socket 6A/16A - 2/3 pin combined 2 module, 230V, 50 Hz complete all asspecified and directed. |
| 123 | S&F Modular ceiling fan regulator, step typefor BLDC ceiling fan 1 or 2 module. |
| 124 | Taking down of Ceiling fan, Ceiling cable end, dismantling blades and removing fan and blades and deposit to the MES store yard complete all as specified and directed. |
| 125 | S&F ceiling fans complete with blades, down rod, regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 126 | Supply, laying and drawing submain wiring in and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the disturbed surfaces as per existing surfaces or as directed on walls 02 runs of IC x 6.00 sqmm (Main Cable and neutral) and one run of IC x 6.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including taking down existing old wireall as specified and directed. Note :- Two runs of IC x 6.00 sqmm (Phase wire and neutral ) and one run of IC x 6.00 sqmm (as earth wire) will be measured as one unit length. |
| 127 | S&Fof factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-54 protection) fabricated from minimum 1.6 mm thick CRCA sheet andfixed on wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn 4 pole MCCB and ELM as incommerand 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 including taking down old DBs all as specified.NOTE :-(a) MCBs/MCCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch. |
| 128 | S&F ofMCCB 63 Amp 4 pole 16 KA at 415 V complete all as specified directed. |
| 129 | S&F of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 10 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed.NOTE :-(a) MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch. |
| 130 | S&F of factory made epoxy polyester powder coated distribution board SP & N 4 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 100 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 10 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed.NOTE :-(a) MCBs shall be measured and paid separately.(b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch. |
| 131 | S&F of single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 complete all as specified and directed. |
| 132 | S&F in replacement MCB SPN 40 Amps rating 240V, 10KA \"B\" curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed. |
| 133 | S&F of single pole MCB 40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 complete all as specified and directed. |
| 134 | S&F in repair surface mounting LED Batten 20W LED light. Fixture should haveminimum efficacy at system level >=100 lumens/Watt, life of fixture not less than 50K Hrs,CCT 4000-6500K &CRI>80, PF≥0.90. An operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed. |
| 135 | S&F of 35 watts 230 V AC outdoor type with High efficient LED Building security light fitting with high pressure die cast Aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP: 65/66 protected complete with bracket made out of 32 mm GI pipe light grade 1.2 mtr long bend to shape with clamps and fixing bolts all as specified and directed. |
| 136 | Taking down carefully exhaust fan any type and deposit to MES store yard with all connected accessories after disconnecting all connections including cutting and making proper smooth round hole suitable for fixing exhaust fan 300 mm sweep dia and refixing the same on site carefully complete all as specified and directed. |
| 137 | S&F of Fresh Air Fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm sweep, single phase,including cutting of holes in wall/windows for fixing the fresh air fan complete all as specified and directed. |
| 138 | S&F of 10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP 65 Protection, System level efficacy of the Luminary is =>90 lm/W, Power Factor =>0.90, Colour Temperature 3000K-6500K, including connecting up with necessary PVC sheathed 3 core 1.5 Sqmm copper conductor flexible wire fixed completeallas specified and directed. |
| 139 | S&F of ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed. |
| 140 | M&L for modular AC Box with 20A SP mini MCB, plastic enclosure & unbreakable Heavy DutyISI mark Plug top complete for AC & geyser point set dully concealed in wall complete all as specified and directed. |
| 141 | M&L in replacement of earthing complete with galvanised steel earth plate 600X600X6 mm thick buried directly in ground (earth pit not les than 2.25 M deep below GL with top edge of plate not less than 1.50 m below GL) connected with GI earth lead wire 4.0mmas earthing leadsby means of bolts, nuts, check nuts and washersall joints as shown on drawings and including excavation, earth work.GI pipe light grade15 mm bore for protection of GI earth wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common saltPCC (1:2:4) type B1 chamber and MS angle iron frame of 40mmx40mm x3 mmand RCC cover 40 mm thick (1:2:4) type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate No 3 of SSR Part -Iand conected to earth test point including testing complete all as secified and directed at site. |
| 142 | S&F in repair, 1100 volts grade heavy duty cable with PVC insulated aluminium stranded conductor served with an inner sheathing of PVC armoured,PVC sheathed 10 sq. mm nominal cross section, 2 core.complete all as specified and directed. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
