|
| 1 | Part A Excavation for foundation in earth, soils of all types, sand, Gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering (including shoring and strutting) etc. complete. (Lift upto 1.50 Metre). by Mechanical means Spec. No. : Bd.A.1 Page No. 259. SSR I.No. 21.02 |
| 2 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift 1.5 m. to 3.0m) By Mechanical Means. dSR I.no. 21.04 |
| 3 | Providing and and filling foundation with sand of approved quality including watering, compacting etc. Complete.(To be excavated with prior approval of supertending etc. Complete. |
| 4 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. |
| 5 | Providing and laying cast in situ / Ready mix , cement concrete in M10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, form work, compacting, roughing them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete finishing if required and curing etc. complete. Spec. No. : Bdf3. SSR I.No. 24.01. Page. no. 217 |
| 6 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete work in foundation like raft, grillages, strip foundation and footings of reinforced cement concrete columns and steel stanchion etc including bailing out water, form work, compaction and finishing, curing roughening the surface if special finish is to be provided (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.3 Page No. 298. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.11. |
| 7 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete columns as per detailed design and drawing or as directed including steel centreing, formwork, , cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complte (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.5 Page No. 300. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.31 Page. No. 222. |
| 8 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete beams and lintels as per detailed design and drawing or as directed including steel centreing, formwork, , ocver blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complte (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.6 Page No. 300. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.50. |
| 9 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete slabs and landings as per detailed design and drawing or as directed including steel centreing, formwork, , ocver blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complte (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.8 Page No. 302. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.70 |
| 10 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Waist slab, and steps of staircase as per detailed design and drawings including steel centering, formwork, steel props, laying/pumping, compacting , curing , finishing eneven and honey combed surface etc. complete. |
| 11 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) SSR I.No. 26.05 |
| 12 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. DSR I.no. 27.01 |
| 13 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints raking out joints, watering and scaffolding etc. Complete. |
| 14 | Providing Second class Burnt brick masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 mm diameter / two hoop iron strips 25 mm x 1.60 mm at every third course, properly bent and bounded at ends scaffolding raking out joints and watering etc. complete. |
| 15 | Filling in plinth and floors with contractor\"s soil, sand or murum in 15 cm. to 20 cm. layers including watering and compaction etc. complete. Spec. No. : Bd.A.11 Page No. 263. SSR I.No.21.37 |
| 16 | Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. DSR I.no. 32.04 |
| 17 | Providing sand faced plaster externally in cement mortor using approved screened sand, in all position inluding base coat of 15 mm thick in cement mortor 1:4 using waterroofing compound at 1kilogramper cmemnt bag curing etc. |
| 18 | Providing and appllying washable oil-bound distemper of approved colour and shade to old and new surface in two coats including scaffolding, preparing the surface etc. |
| 19 | Providing and appllying two coat of water proof cement paint of approved manufacture and of approved colour to the plastered surface inluding scafflong if necessary, cleaning and preparing etc. |
| 20 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. DSR I.no. 26.33 |
| 21 | Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete. |
| 22 | Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. DSR I.No. 39.09 |
| 23 | Providing and fixing Orissa type white glazed earthenware 575 mm water closet pan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete. |
| 24 | Providing laying, and fixing P.V.C.pipe white of 100 mm dia. Withs, reducers, clmps, etc. Inluding necessary excavation, trench filling etc. Complete. |
| 25 | Providing and laying, matt finish ceramic tiles of having size 30 cm X 30 cm confirming to I.S. 15622/2006 (group D-11-A) and 7 to 8 mm thick for flooring in required position etc. |
| 26 | Providing and laying ceramic tiles of having size 30 cm x 30 cm. And confirming to corresponding I.S. For dado and skirting in required position with readymade adhesive mortor of approved quality on plaster of 1:2 cement mortor inluding joints filling with white/ colour cement slurry cleaning curing etc. |
| 27 | Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring DSR I.No. 33.40 |
| 28 | Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters DSR I.no. 42.53 |
| 29 | Providing laying, and fixing P.V.C.pipe white of 15 mm dia. With fitting such as bends, tees reducers clmps, etc. Inluding necessary excavation, trench filling etc. Complete. |
| 30 | Providing laying, and fixing P.V.C.pipe white of 20 mm dia. With fitting such as bends, tees reducers clmps, etc. Inluding necessary excavation, trench filling etc. Complete. |
| 31 | Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete. |
| 32 | Providing and fixing coloured glazed earthnware wash hand basin of 63 cm X 45 cm size including etc. |
| 33 | Providing and fixing 10 cm C.I. Nahani trap inluding C.I. Grating bend and piece of C.I. Pipe upto the outside face etc. |
| 34 | Providing and fixing board displaying information, such as \"Name of work, Tender cost, Name of contractor, work completion and liability period etc, having rectangular shape of 1.20 m x 0.90 m size made out 18 gauge (1.25m) thick mild steel sheet painted with one coat of zinc chromate stoving primer and two coats of zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbos etc with approved colour shade paint complete, on M.S. angle of size 3 x 35 x 3 mm frame with properly cross braced M.S angle of size 35 mm x 35 mm x 3 mm duly painted including two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling transportatiion, and labour etc complete Spec. No. As directed by engineer in charge MORTH 801 S.S.R. I.No. 6.96 |
| 35 | Royalty Charges |
| 36 | Providing Quality Control Test 1. M20 Cube Test |
| 37 | 2.Water Absorption (Set of 5 Bricks), (Compressive Strength) |
| 38 | Part B Excavation for foundation in earth, soils of all types, sand, Gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering (including shoring and strutting) etc. complete. (Lift upto 1.50 Metre). by Mechanical means Spec. No. : Bd.A.1 Page No. 259. SSR I.No. 21.02 |
| 39 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift 1.5 m. to 3.0m) By Mechanical Means. dSR I.no. 21.04 |
| 40 | Providing and and filling foundation with sand of approved quality including watering, compacting etc. Complete.(To be excavated with prior approval of supertending etc. Complete. |
| 41 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. |
| 42 | Providing and laying cast in situ / Ready mix , cement concrete in M10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, form work, compacting, roughing them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete finishing if required and curing etc. complete. Spec. No. : Bdf3. SSR I.No. 24.01. Page. no. 217 |
| 43 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete work in foundation like raft, grillages, strip foundation and footings of reinforced cement concrete columns and steel stanchion etc including bailing out water, form work, compaction and finishing, curing roughening the surface if special finish is to be provided (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.3 Page No. 298. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.11. |
| 44 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete columns as per detailed design and drawing or as directed including steel centreing, formwork, , cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complte (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.5 Page No. 300. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.31 Page. No. 222. |
| 45 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete beams and lintels as per detailed design and drawing or as directed including steel centreing, formwork, , ocver blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complte (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.6 Page No. 300. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.50. |
| 46 | Providing and laying in situ / Ready mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete slabs and landings as per detailed design and drawing or as directed including steel centreing, formwork, , ocver blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complte (excluding reinforcemetn anf structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reverisble drum type mixer/concrete batch mix plant (pan mixer) etc complete with fine aggregate (Natural sand / CRushed sand VSI grade finely washed etc ) finishing if required and curing etc Spec. No. : Bd.F.8 Page No. 302. and B.7 , Page. No. 38 S.S.R.I. I.No. 25.70 |
| 47 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks compacting , curing , finishing and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) SSR I.No. 26.05 |
| 48 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually , striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. DSR I.no. 27.01 |
| 49 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints raking out joints, watering and scaffolding etc. Complete. |
| 50 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall inluding mild steel longitudinal renforcement of 2 bars of 6 mm diameter/2 hoop iron strips 25 mm x 1.6 mm placed etc. Complete. |
| 51 | Filling in plinth and floors with contractor\"s soil, sand or murum in 15 cm. to 20 cm. layers including watering and compaction etc. complete. Spec. No. : Bd.A.11 Page No. 263. SSR I.No.21.37 |
| 52 | Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. DSR I.no. 32.04 |
| 53 | Providing sand faced plaster externally in cement mortor using approved screened sand, in all position inluding base coat of 15 mm thick in cement mortor 1:4 using waterroofing compound at 1kilogramper cmemnt bag curing etc. |
| 54 | Providing and appllying washable oil-bound distemper of approved colour and shade to old and new surface in two coats including scaffolding, preparing the surface etc. |
| 55 | Providing and appllying two coat of water proof cement paint of approved manufacture and of approved colour to the plastered surface inluding scafflong if necessary, cleaning and preparing etc. |
| 56 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. DSR I.no. 26.33 |
| 57 | Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete. |
| 58 | Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. |
| 59 | Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe having over all daimeter 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. with window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt.. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. |
| 60 | Providing and fixing mild steel grill work for windows, ventilators, etc.15 kilogram/Square Meter as per drawing inluding fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. |
| 61 | Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring DSR I.No. 33.40 |
| 62 | Providing and laying in position flooring of telephone black / amba white/catbary brown/Rubyred/ Ocean Brown granite Stone of Approved shade and size 18 mm to 20 mm thick on bed 1:6 cement moror etc. |
| 63 | Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channel of 18 x 9x 3 mm minimum size, crossing of M.S. Flats of size 18 x 5 mm T or E section etc. |
| 64 | Royalty Chargs |
| 65 | Providing Quality Control Test 1. M20 Cube Test Please Enable Macros to View BoQ information |
