|
| 1 | Renovation of Office space for Store located at Ground Floor MeitY |
| 2 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 3 | Dismantling wooden boardings in lining of walls and partitions, excludingsupporting members but including stacking within 50 metres lead : |
| 4 | Thickness above 10 mm up to 25 mm |
| 5 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 6 | Of area beyond 3 sq. metres |
| 7 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 8 | For thickness of tiles 10 mm to 25 mm |
| 9 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 20 km for all lifts, complete as per directions of Engineer-in-charg |
| 10 | Up to 20 km Dis. |
| 11 | 18 mm thick cement plaster in two coat under layer 12 mm thick cement plasterwith cement and coarse sand- 1:5 (1 cement: 5 Course sand)and top layer 6mm thick cement plaster 1:3 (1 cement: 3 Course sand) finishing rough with spong. |
| 12 | Providing and applying plaster of putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 13 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : |
| 14 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 15 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : |
| 16 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:) |
| 17 | With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 18 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. |
| 19 | Size of Tile 600 x 600 sqmm |
| 20 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) |
| 21 | Second class teak wood |
| 22 | Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS: 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of: (Note:- Butt hinges and necessary screws shall be paid separately) |
| 23 | 12 mm thick plain grade -1, medium density flat pressed three layer particle board FPT-I or graded wood particle board FPT-I, IS: 3087 marked, bonded with BWP type synthetic resin adhesive as per IS: 848 |
| 24 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 25 | 1.5 mm thick |
| 26 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete |
| 27 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete |
| 28 | D-250x10 mm |
| 29 | W-150x10 mm |
| 30 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 31 | Chromium plated Brass mortice latch and lock 100x65 mm with 6 levers and a pair of brass lever handles |
| 32 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 33 | Providing wood work in frames of false ceiling, partitions etc.sawn and fixed in position with necessary stainless steel screws etc |
| 34 | Sal wood |
| 35 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete |
| 36 | 2nd class teak wood |
| 37 | 50 x 20 mm |
| 38 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clip of size 85x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge |
| 39 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 40 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1.The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2.Applying two coats of sealer with pray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3.On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a lightwet rubbing is done this surface is further allowed to dry for 12 hrs. 4.On this, 1st coat of melamine polish is applied with spray gun usingmelamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 41 | Providing and fixing panelling or paneling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebated to be measured). Panelling for panelled and glazed shutters 25 mm to 40 mm thick: Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick conforming to IS:14587 |
| 42 | Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. |
| 43 | 50x50 mm (base and height) |
| 44 | Supplying of LEDRecessed/surfaceDown lighter (Round/square/Rectangular) COB Typeof following body material and construction as per IS : 10322withdriver as per the requirement with Driver efficiency >85%,Operating voltage AC 140-270Volt,freq50/60 hz,Operating temp range-15degto40degcentigrade,internalsurgeprotectionof2.5KVwithShort&Open circuit protection ,THD < 10% , P. F.≥0.95,IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flickershould be below 5 %), life time (LED,Driver & electrical circuitary), life time of minimum50000 Burning Hourswith,70%ofinitial Lumen maintained tilllife ends , CCT3000°K/4000°K /5700°K /6000°K/6500°K(AsperANSIBin), SDCM(Standard Deviation Color Matching) <3, Maximumpowerconsumptionshouldnotmorethan the specified rating and Fixture shall be ofrelevant BIS standard andtrade mark certificate ( T.C.).Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing.OEMmusthaveitsowninhouseNABLlabsetupforalltestingfacilitiesforLED fixtures.\"completeinallrespecti/cconnectionswith1.5sqmmFRLS,PVCinsulatedcopper conductor singlecore cable and earthing etc. as required with Minimum 5 year OEM warranty.System lumenefficacy≥120<135 lm/Watt output . LM79 & LM80 Test reportfromNABL lab foralltestingrequiredforLED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermalmanagement:heatsinkofaluminiumhousing such that LED junction temperature shall not rise above 90°C) |
| 45 | LED Panellight 2x2ft., (System lumen efficacy>135 lm/Watt) Supplying, installation, Testing & Commissioning of Panellight 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirementwith Driverefficiency >85%, Operating voltage AC140-270 Volt,frequency50/60hz,Operatingtemprange-50Cto40 0C,internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95,IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free,(flicker should be below 5 %), life time (LED, Driver & electrical circuitry),of minimum50000 Burning Hours with , 70% of initial Lumenmaintained tilllife ends ,CCT 3000°K /4000°K /5700°K /6500°K(As perANSI Bin), SDCM (Standard Deviation Colour Matching) <3,Maximumpower consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete inallrespecti/c external connectionswith1.5sq.mm FRLS/HFFR, PVC insulatedcopper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy>135lm/Watt output . LM79 & LM80 Test report andalltestingrequiredforLED fixtures as per BISshall be submitted. Shape size and CCT shall be as approved by Engineer-inCharge as per requirement. (Thermal management:heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).Powdercoateddiecast/Extruded aluminiumBody (Thickness > 1.20 mm) |
| 46 | 36 watt |
| 47 | SLOTTED ANGLE RACKModel No.: -Size: - 915(L) * 450(D) * 2440(H)mmSPECIFICATION: - Providing Slotted Angle Rack Overall Size 915W x 450D x 2440H. Slotted Angle Rack CRCA Sheet Panels 18 gauge. Thick Prime Quality Powder Coated Finish With Approved Shade. The Angle Of Slotted Angle Rack 40x40 With 2mm Thick Powder Coated. Each Shelf Made Of CRCA Sheet Powder Coated in the thickness of 1mm. Shelf Shall be Formed Such That Lengthwise Edge Are Bent Two Times At Right Angles. First Bend Shall Be 30mm & Second Bend 8mm. Galvanized Nut Bolt Of Hexagonal Hand 8mm x 25mm Long. No Sharp Edges On Angle Iron Ends. CLOSE Rack Divided Into Equal Parts. Metallic Panels Screw With Nut & Bolt. CRCA Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. Provided high quality cold rolled close annealed(CRCA) sheet anticorrosion treated components, duly power coated with ten tank phosphating procedure with 60 to 70 microns. |
