|
| 1 | Demolition of cement concrete (un-reinforced) of any description and in any position, not otherwise specifically provided for, complete all as specified and directed. |
| 2 | Demolition of plain cement concrete of any description and in any position, not otherwise specifically provided for, complete all as specified and directed. |
| 3 | Demolition of stone slabs and tiles of any description or thickness, laid, bedded and pointed in any mortar as in kitchen platform, floors, aprons etc, complete all as specified and directed. |
| 4 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the premises, complete all as specified and directed. |
| 5 | Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed. |
| 6 | Demolition of brick work or stone masonry, built in cement mortar and removal of rubbish from site, complete all as specified and directed. |
| 7 | M&L for brick work with sub class ‘B’ bricks, old size, straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed. |
| 8 | M&L for brick work with sub class ‘B’ bricks, old size, straight or curved on plan exc 6m mean radius, built in CM 1:4, complete all as specified and directed. |
| 9 | All as per serial item No. 8.00 here-in-above but except bricks.Note :- Old bricks obtained against dismantling shall be used. |
| 10 | M&L for walling of random rubble, coursed, well bonded, bedded and solidly hearted, built in CM 1:6, complete all as specified and directed. |
| 11 | All as per serial item No. 10.00 here-in-above but except stones.Note :- Old stones obtained against demolition shall be used. |
| 12 | Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling, coursed, hammer dressing with maximum depression on face from straight edge held against the dressed surface, not exc 40mm on lime/sand stone, complete all as specified and directed. |
| 13 | M&L for RCC 1:2:4 (nominal mix) type B-1 (using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. |
| 14 | Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished concrete surfaces, complete all as specified and directed. |
| 15 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia,complete all as specified and directed. |
| 16 | M&L for mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia,complete all as specified and directed. |
| 17 | M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid/ fixed over and including screed bed or bedding layer of 15mm thk for laying floor finishes in CM 1:4, complete all as specified and directed. |
| 18 | M&L for coloured glazed ceramic tiles of size 300mm x 450mm x 7-8mm thick as on vertical surfaces of walls such as as in dados, skirtings etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick rendering on fair faces of brick /concrete surfacesin cement mortar 1:4 and fair to recive tiles, complete all as specified and directed. |
| 19 | M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in cills, steps, seismic and other similar bands, parapets and railings up to 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, mud stops including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 20 | M&L for 50mm thick cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in plinth protection, laid in alternate bays (not exc 2 Sqm each)and finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection and filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed. |
| 21 | M&L for treatment of sunken floor surfaces with 0.488 Kg/Sqm first layer of slurry of cement mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer shall be allowed to be cured for 4 hours and then applying in second layer slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer based modified cementitious composite compound @ 0.126 Kg/Sqm. This layer shall be allowed to be cured for 4 hours including taking down old/existing treatment with wire brusing and clearing the dust and foreign material before new treatment and incuding one GI light grade 450mm long 32 mm dia spout to each sunken floor, complete all as specified and directed. |
| 22 | M&L for plain cement concrete 1:5:10 type E-2 (using 40mm graded crushed stone aggregates) as in sunken floor, foundatiom, complete all as specified and directed.Note :- The work shall be executed in G+3 storey bldg. |
| 23 | M&L for plain cement concrete 1:2:4 type B-2 (using 40mm graded crushed stone aggregates) as in sunken floor, foundatiom, complete all as specified and directed.Note :- The work shall be executed in G+3 storey bldg. |
| 24 | S&F in replacement of wash down water closet (pedestal pattern) complete with pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. including PVC seat and cover for pedestal pan, complete all as specified and directed.Make :- CERA Cat Part No. 2080 (Camelia) or Jaquar Cat Part No. CNS-WHT-OP01 or equivalent as specified in Particular Specifications. |
| 25 | M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and directed. |
| 26 | S&F in replacement of PVC low level flushing cistern of capacity 10 ltrS, white with inlet, ball valve, float and handle including breckets, flush pipe of polyethylene of low or high density or PVC 32mm dia and connection to pipes, complete all as specified and directed. |
| 27 | S&F wash hand basin, vitreous china (flat back or angle back type), size 550mm x 400mm, with padestalincluding cutting for and pinning in ends of brackets or erecting stand including CP waste coupling of 32mm dia and PVC waste pipe of 32mm bore, complete all as specified and directed. |
| 28 | S&F chromium plated brass CP basin mixer for mixing hot & cold water, screwed down for 15mm bore iron pipe, complete all as specified and directed. |
| 29 | S&F in replacement of soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cromium plated screws, complete all as specified and directed. |
| 30 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf, 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. |
| 31 | S&F PVC connection of 15mm size with PTMT nuts of length 450/600mm, complete all as specified and directed. |
| 32 | Dismantling of cast iron/ rain water pipe or reinforced concrete drain pipes, jointed in cement, complete all as specified and directed. |
| 33 | S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with stack clapms and fixed with nut and bolts, complete all as specified and directed. |
| 34 | S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls with stack clapms and fixed with nut and bolts, complete all as specified and directed. |
| 35 | S&F 110mm bore PVC (SWR) bends with access door of any radius, complete all as specified and directed. |
| 36 | S&F 110mm bore PVC (SWR) branch piece, single (single Y/T) equal or unequal, complete all as specified and directed. |
| 37 | S&F 75mm bore PVC (SWR) bends with access door of any radius, complete all as specified and directed. |
| 38 | S&F 75mm bore PVC (SWR) branch piece, single (single Y/T) equal or unequal, complete all as specified and directed. |
| 39 | M&L for 20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding and polishing with rounding to edges as required, fixed over and including 15mm thick screed bed/ plaster in CM 1:4, complete all as specified and directed. |
| 40 | Dismantling of water tank and removing to store, capacity exc 250 litres but not exc 500 litres with all necessary fittings, complete all as specified and directed. |
| 41 | S&F 3 layer rotational moulded polyethylene water storage tank of any colour, 1000 ltrs capacity (cylindrical vertical with closed top) with 20mm dia ball valve, epoxy coated aluminum rod, plastic ball etc, hoisted and fixed in position including tank nipple inlet and outlet and conneting pipes, complete all as specified and directed. |
| 42 | Taking up or down 15mm bore steel water tubing and connections including cleaning for refixing or removal from site to store, complete all as specified and directed. |
| 43 | M&L for 15mm bore GI water tubing, medium grade including all fixing acessoriesand laid in ceilings or laid in floors, complete all as specified and directed. |
| 44 | Refixing of old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm, complete all as specified and directed. |
| 45 | S&F in replacement of bib tap, long body, chroimum plated (ISI Marked with valid CML No) with crutch or butterfly handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule and fixed including elbow/ socket etc. as required at site, complete all as specified and directed. |
| 46 | S&F CP shower with arm 15mm size 195mm long with bend of 45 degree with flange including taking down the existing UNSVshower of any type/shape, complete all as specified and directed. |
| 47 | S&F angle cock of 15mm dia, chromium plated, fittings as required at site and taking down existing unserviceable angle cock, complete all as specified and directed. |
| 48 | S&F concealed stop valve chromium plated, brass, fancy tap, screwed down high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed including fittings as required at site, complete all as specifiedand directed. |
| 49 | S&F 25mm dia gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipes including taking down the existing unserviceable valve, complete all as specified and directed. |
| 50 | Dismantling of CGI/ AC or any other type sheet of any description including ridges etc, complete all as specified and directed. |
| 51 | S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 52 | M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde-E- 250) Quality-A, complete all as specified and directed. |
| 53 | Taking down cement plaster of any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 54 | M&L for 10mm thick rendering on fair faces of brick /concrete surfacesin cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 55 | M&L for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over one coat of priming and over 2 to 3mm thick of wall care putty, complate all as specified and directed. |
| 56 | M&L for preparation of new plastered surfaces of walls and applying three coats of white wash/colour wash on ceiling/wall, complete all as specified and directed. |
| 57 | M&L for preparation of new plastered surfaces of walls or concrete surfaces and applying two coats of cement based paint on a coat of alkali resistant priming paint, complete all as specified and directed. |
| 58 | M&L for 15mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement including scaffolding arrangement as per site requirement upto G+1 storey bldg, complete all as specified and directed. |
| 59 | M&L for 15mm thick rendering on other than fair face of brick work or concrete surface in CM 1:4, finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 60 | M&L for rendering 5mm thick on fair face of brick work or concrete surfaces of ceiling in cement mortar 1:3, finished the surface even and smooth without using extra cement, complete all as specified and directed. |
| 61 | M&L for raised pointing to RR masonry in CM 1:4, complete all as specified and directed. |
| 62 | S&F in replacement of 25mm dia stainless steel curtain rod with fixing of domes with stainless steel brackets etc, complete all as specified and directed. |
| 63 | Taking down chowkats or frames of any type or description (without taking off shutters from frame), area not exc 1.50 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed. |
| 64 | Taking down chowkats or frames of any type or description (without taking off shutters from frame), area not exc 1.50 Sqm but not exc 4.0 Sqm each including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed. |
| 65 | S&F solidPVC door frame ofsize 50mm x 47mm, made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube in opening as per specification and drawings, complete all as specified and directed. |
| 66 | S&F PVC moulder door shutter of wallnut colour of 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for style and plain colour PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and directed. |
| 67 | S&F factory made (box type) mild steel widow/ ventelators glazed and gauged combined shutter with side hung including box type hinges steel peg stay locking arrangement with glazing and gazing bar dovetailed or welded and one shop coat of red oxide primer & two coats of synthetic enamel paint, complete all as specified and directed. Notes :- (i) The window / ventelator shall be fabricated as per drg No. CEUZ/TD/1302/2009 sheet 1/3 to 3/3.(ii) MS fillets, glazing, wire gauges shall be measured and paid for seperately.(iii) One side out to out dimensions shall be measured for payment of combined window (glazed & gauged). |
| 68 | S&F 4mm thick plain/ pin headed/ frosted sheet glass, ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed. |
| 69 | M&L for preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed. |
| 70 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 71 | S&F pressed steel frames, size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, cement concrete 1:2:4type B-0 (using 12.5mm graded crushed stone aggregates) filling inside hollow section etc, complete as specified and directed. |
| 72 | S&F pressed steel frames, size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, cement concrete 1:2:4type B-0 (using 12.5mm graded crushed stone aggregates) filling inside hollow section etc, complete as specified and directed. |
| 73 | S&F 40mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/ frame to match and polished on back side and sides of shutters, complete all as specified and directed. |
| 74 | S&F 35mm thick 2nd class hard wood glazed and skeleton factory made shutters (three panel) open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I and fitted to chowkats, complete all as specified and directed. |
| 75 | S&F 150mm long aluminium, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed. |
| 76 | S&F 150mm long aluminium bow handles, cast type, anodised and fixed, complete all as specified and directed. |
| 77 | S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed. |
| 78 | S&F floor door stoper of 140mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and directed. |
| 79 | S&F MS helical door spring 150mm size including roller and roller plate, fixed to wooden or steel frames with welding etc, complete all as specified and directed. |
| 80 | M&L for preparation of new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 81 | S&F towel rod CP brass 20mm bore and 600mm long, fixed with SS screws and plug, complete all as specified and directed. |
| 82 | S&F towel ring CP brass, fixed with SS screws and plug, complete all as specified and directed. |
| 83 | S&F 600mm x 450mm size bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated, complete all as specified and directed. |
| 84 | S&F 75mm bore PVC (SWR) floor trap with stainless steel grating including jointing to waste pipe, fixed in cement with solvent cement including taking down old PVC or CI floor trap of any type, complete all as specified and directed. |
| 85 | Roughing surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc. including taking down tarfelt and brushing neat cement slurry @ 3.50 Kg/Sqm including 10mm thick plastering in CM (1:3), finished even and smooth mixed with water proofing compound. Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and providing Atactic Polypropylene polymer (APP) modified five layered prefabricated water proofing membrane with thermal fusible properties on both side having minimum 3mm thick and unit weight not less thaan 4.00 Kg/Sqm reinforced with non woven spun bonded polyester reinforcement < -2C cold flexibility. The layer of the membrean shall be laid using butane torch and sealing all joints properly, leaving no bare edgs or end of APP membrane and finishing the surfaces with trowel or otherwise to obtain a unifrom surfaces. The minimum side lap and end lap shall be kept at 75mm and 100mm respectively. The membrane shall be laid over a coat of bituminous primer @ 0.30 Kg/ltr per Sqm made by the same membrane manufacture after necessary surfaces preparatory works such as cleaning the surfaces throughly, shapping mouth of outlets including cutting grooves (50mm x 50mm) in parapat and inserting edgs of membrane and mending goods damage by sand cement mortar (1:4) and shall be finished in all respect as per directed by Engr-in-Charge. Note :- The laying of the membrane shall be got done by authorized applicator of the membrane manufacturer. |
| 86 | Surface excavation not exc 30cm deep and averaging 18cm deep and getting out in any type of soil, complete all as specified and directed. |
| 87 | Excavating over areas, not exc 1.5 mtr deep and getting out in any type of soil, complete all as specified and directed. |
| 88 | Excavation in trenches in any type of soil, not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for foundation, for shafts, manholes, pier holes, laying of cable/ pipe etc, not exc 10 Sqm on plan and not exc 1.50 mtr in depth and getting out inany type of soil, complete all as specified and directed. |
| 89 | M&L for returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick, complete all as specified and directed. |
| 90 | Removing excavated material/ soil to a distance not exc 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point, complete all as specified and directed. |
| 91 | Removing excavated material/ soil to a distance exc 250 mtr but not exc 500 mtr and depositing where directed, complete all as specified and directed. |
| 92 | S&F HDPE DWC (Double wall corrugated) pipes confirming to IS-16098 of DN/ID 180mm dia, Pressure rating SN-08, fixed with rubber seal and coupler required with and including suitable bends 90/60/45 degree etc. Single \"Y\" Jn complete as required fixed as per manufacturer\"s instructions, laid in trenches for sewage lines, complete all as specified and directed.Note :- Rates included for pipes, bends any size and type, \"Y\" Jn coupler/ adapter etc. as required and net total length of pipes with fittings shall be measured for payment purpose. |
| 93 | M&L for hardcore of broken stone or boulders of gauge not exc. 63mm, deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 94 | M&L for plain cement concrete 1:4:8 type D-2 (using 20mm graded crushed stone aggregates) as in foundation, bed for laying sewage lines or mass concrete, complete all as specified and directed. |
| 95 | M&L for precast reinforced cement concrete 1:2:4 typeB-1 (using 20mm graded crushed stone aggregates) as in cover slabs for man holes with plain faces, finished fair and smooth etc, set in CM 1:6, complete all as specified and directed. |
| 96 | M&L for 75mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base of flooring etc, complete all as specified and directed. |
| 97 | M&L for 100mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in sub base of flooring etc, complete all as specified and directed. |
| 98 | M&L for cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) as in kerbs or mud stops, rounded or chemfered on edges, complete all as specified and directed. |
| 99 | M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS:15658-2006 of 80mm thickness M-40 Grade with grey cement and pigment, complete all as specified and directed. |
| 100 | Dismantling of wrought iron/ mild steel/ steel works of any description and in any position, complete all as specified and directed. |
| 101 | M&L for mild steel work such as angle iron post, flat iron in fencing including cutting as making double swan neck i.e \"Y\" shaped including welding with proper overlapping & welding MS plate with angle iron bottom as directed drilling holes notching for wire etc embedded in concrete, fixed vertically, conforming to Fe-290 Gde E-165, complete all as specified and directed. |
| 102 | M&L for mild steel framed work such as iron door, grills, gratings etc. with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, railing, frame work for water tanks and similar work, conforming to Fe 290 Gde-E-165, complete all as specified and directed. |
| 103 | S&F concentina coil punched type (including spike and handle) with 50/51 turns and dia 450/600mm, having a 2.6mm dia core wire of high carbon spring steel of high tensile strength. The punched tape and core wore are electro galvanized to provide protection againist out door exposure. The puched tape is mechanically crimped over the cover wire and then formed into a coil at avariouys parts of the periphery of the coil steel clips connect the individual turns of the coil to each other so that it open up like an accordion. The weigth of each coil will be 9 Kg (+/-5%) without packing material and coil length wound with bituminious hession cloth of providing protctive coatings, complete all as specified and directed. |
| 104 | S&F in replacement of galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc, complete all as specified and directed. Note :- Each line wire to be measured and paid. |
| 105 | Restraining, resecuring including making good galvanised 2 strand, steel barbed wire of 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and including galvanised mild steel wire, staples or steel pins etc, complete all as specified and directed. Note :- Each line wire to be measured and paid. |
| 106 | S&F 110mm dia PVC (SWR) pipe as in weep holes, complete all as specified and directed. |
| 107 | M&L for preparation of new steel surfaces of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed. |
| 108 | M&L for two coats water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & colour stay technology, excellent drit pick up resistance with low VOC less than 50 gram/litre as per LEEDS specifications, Anti Algal properties in two coats @ 1.79 Itr (undiluted with water as per manufacturer instructions applied over priming coat with fully automatic airless stray machine of paint application with a flow speed of min 1 Itr per minute having a pressure of 3300 PSI including 1-1.2mm thickness of altek/ Birla white putty to obtain smooth and even finish using sand paper and allow 6-8 hrs to dry the surface in both the coats of paint, complete all as specified and directed by Engineer-in-Charge. Notes :- (a) The work pertaining to periodical services & water proofing shall be executed from authorized applicator through manufacturer of which the materials i.e. paint, distermpe, cement base paint, putty etc. is proposed to be used by the contractor and approved by Garrison Engineer. (b) Memorandum of Understanding (MOU) with manufacturer as approved by GE shall be submitted by the contractor before execution of work. |
| 109 | M&L for chequered cement concrete tiles of size 30cm x 30cm x 25mm thick each, coloured with mixture of white & grey cement in equal portion and no pigment and admixtures, set, jointed and ointed in neat cement slurry, laid/ fixed over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 110 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed. |
| 111 | S&F powder coated (of approved colour) aluminium sections as in frames and shutter of doors, windows (hung/ sliding type), ventilators (louvers/ fixed type) and fixed frame etc. fixed to wall including preparation of disturbed porion both side (internal & external surfaces of wall) to match with existing surfaces treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/ outer), complete all as specified and directed. |
| 112 | Taking down carefully point wiring copper/ aluminium (light, fan, socket, and power) complete (fittings such as switches ceiling roses, pendent regulators sockets etc. tobe measured and paid for separately removing materials to store for keeping of safe custody and making good the disturbed surfaces, complete all as specified and as directed. |
| 113 | Dismantling and taking down fluorescent tube light of any wattage or size fittings for repair or replacement of burnt/ worn out accessories or carrying to MES store for reuse or taking in schedule of credit, complete all as specified and as directed. |
| 114 | Taking down unserviceable / serviciable MCB DB\"s/ AC\"s box including MCCB/ MCBs taking in schedule of credit of any size/ rating, complete all as specified and directed. |
| 115 | M&L for point wring for one light/ ceiling fan point, controlled by one switch with 1.5 sqmm (nominal area PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLS in and including concealed PVC conduit 25mm dia medium duty ISI marked including sutiable new steel sunken boxes, modular frame and cover plate for fixing of modular switches as per required point, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLS connected to common earth dooly complete including cutting, chasing the surface and then making good as the same, complete all as specified and directed for the followings :-One light point / fan point controlled by one switch. |
| 116 | One exhaust point controlled by one switch. |
| 117 | One 3/5 pin socket outlet, 5 Amp independent. |
| 118 | One socket outlet 3 Pin, 5 Amps, SP on same board. |
| 119 | One two way point controlled by one 2 way switch. |
| 120 | M&L for point wring for power point controlled by one switch with 2.5 sqmm (nominal area PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLS in and including concealed PVC conduit 25mm dia medium duty ISI marked including sutiable new steel sunken boxes, modular frame and cover plate for fixing of modular switches as per required point, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 2.5 sqmm copper conductor cable FRLS connected to common earth dolly, complete all as specified and directed. |
| 121 | S&F in replacement of modular switch, single pole, one way, 10 Amps, 1 module, complete all as specified and directed. |
| 122 | S&F in replacement of modular switch, single pole, one way, 16 Amps, 1 module, complete all as specified and directed. |
| 123 | S&F in replacement of modular switch, 10 Amps, two way, 10 Amps, 1 Module,complete all as specified and directed. |
| 124 | S&F in replacement of modular socket, 6 Amps, 2/3 pin combined, 2 module, complete all as specified and directed. |
| 125 | S&F in replacement of modular socket, 6/16 Amps, 2/3 pin combined, 2 module, complete all as specified and directed. |
| 126 | S&F in replacement of ceiling rose, 3 Phase, PVC/polycarbonate isolated body, complete all as specified and directed. |
| 127 | S&F in replacement of modular electronic fan regulator, step type, two module, 120 watt, 230 volt and making all necessary connections, complete all as specified and directed. |
| 128 | S&F in replacement of slim linear LED lighting fixture 20 Watt LED batten with full base of extruded aluminium body section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fitings, complete all as specified and directed. |
| 129 | S&F in replacement of E-Lite LED Curve lighting fixture 2 feet, 10 watt LED batten with full base of extruded polycarbonate body environmental friendly, energy efficient ready to use pack with isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings, complete all as specified and directed. |
| 130 | S&F in replacement of E-Lite LED Curve lighting fixture 05 watt LED batten (mirror light+table light) with full base off extruded polycarbonate body environmental friendly, energy efficient ready to use pack with isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings, complete all as specified and directed. |
| 131 | S&F in replacement of 35 Watt LED security light fitting with ASTRA NEO street lights are made up of pressure die cast housing with toughened glass and high power LED with secondary optics and IP-66 protection and with 0.60 mtr long 20/25mm dia (as per manufacturer standard) GI Pipe in 45 degree bend shape and necessary clamping devices as required at site, complete all as specified and directed. |
| 132 | S&F in replacement of 2 feet x 2 feet ceiling mounting 35/36 Watt LED warm/ white light fitting Vector series tiles allow you to create beautiful pattern on your ceiling. Seamless integration with ceiling, easy maintenance, high system efficacy makes it a hassle free choice for office spaces alongwith 3 CCT options & convert your ceiling into a beautiful piece of art, complete all as specified and directed by Engr-in-Charge. |
| 133 | M&L for sub main wiring with copper conductor cable 2 runs of cable multistaranded 6 Sqmm PVC FRLS ISI marked with all insulated unsheathed in and including PVC concealed conduit 25mm dia medium grade fittings including 6 Sqmm copper conductor cable PVC insulated unsheathed multithreaded using as continues earth wire connected to common earth and earth dolly complete including taking down old existing submain wiring, complete all as specified and directed. |
| 134 | M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to earth lead wire of GI wire 4mm dia by means of nuts, bolts, washers and check nuts of galvanized iron and including 15mm bore GI pipe light grade upto 1.5 mtr below GL as protection pipe and excavation, earth work, charcoal dust, common salt, PCC 1:3:6 type C-1 chamber with cover and RCC 1:2:4 type B-1 (using 20mm graded crushed) stone aggregate, reinforced with 6mm dia round bars @ 75mm c/c both way with MS handle 12mm dia, PGI funnel and wire mesh, complete all as shown in electrical plate No. 3 of SSR Part-I and connected to earthing test point including testing on completion, complete all as specified and directed. |
| 135 | S&F in replacement of exhaust fan, steel body, AC, single phasee 230 volts of size 300mm sweep with blades and frame and lover, complete all as specified and directed |
| 136 | S&F in replacement of ceiling fan complete with blades, down rods electronic regulators and accessories 230 Volts, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE 5 star rated with brush less direct current motor (BLDC), omplete all as specified and directed. |
| 137 | S&F in replacement single pole and neutral sheet metal steel powder coated distribution board for MCBs, fitted with bus bar neutral link earth bar and din rail suitable for use on 240 V, 50 Hz, double door, 12 Way, complete all as specified and directed. |
| 138 | S&F MCB SPN 40-63 Amps, 240 Volts, repturing capacity 10 KA, \"C\" Series, complete all as specified and directed. |
| 139 | S&F MCB SP, 6 to 32 Amps, 240 Volts, repturing capacity 10 KA, \"C\" Series, complete all as specified and directed. |
| 140 | S&F in replacement of sheet metal VTPN DB - DPX3 160 MCCB DB, 04 Way (Optimum + 12) with metal door 415 Volts grade IP-43 Protection Grade, fixed flush to wall complete including connections should be provide with necessary reducer lugs, complete all as specified and directed. |
| 141 | Taking down ceiling fan/ exhaust fan, sealing cable end etc. and shifting to store complete and rehanging the same after overhauling and painting with white synthetic enamel paint (two coats) with the help of spray gun and connecting with three core flexible copper conductor cable 1.0 Sqmm, complete all as specified and directed. |
| 142 | S&F in replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of 20 Amps 240 volt capacity, complete all as specified and directed. |
| 143 | S&F in replacement of DPX3 thermal magnetic MCCB, 4 Pole, 100 Amps, 415 Volts, 16 KA INCLUDING MAKING NECESSARY ARRANGEMENT, complete all as specified and directed. |
| 144 | Taking down the existing geyser of any capacity carefully and shifting to the MES store yard and re-fixing the same after completion of B/R works including all connected accessories, complete all as specified and directed. |
| 145 | Supply and laying in replacement of XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 4 Core, laid in trenches/ floor/ pole/ GI pipe complete including cutting/ chasing to any surface and making good to the disturbed surface to match with the existing surface, complete all as specified and directed. |
| 146 | M&L for 40mm bore Gl tubing light grade with all fitting and fixed in wall and floor or fixed to pole, complete all as specified and directed. |
| 147 | M&L for dry river sand as in cushioning to underground cables, provided with a layer of sand 8cm thick before laying the cable and 15cm thick after laying the cable and stretching the cable, complete all as specified and directed. |
| 148 | Supply and laying sub class \"B\", old size brick, well burnt as covering or mechanical protection to UG cable, complete all as specified and directed. |
| 149 | S&F in repair rigid non - metalic PVC casing caping of 25/12mm inclusive of all elbow, tees,etc complete all as per the direction of Engr-in-Charge. |
