|
| 1 | M&L for Roughening surfaces of old concrete beam/column/slab by picking, sweeping clean and washing down with water to remove dust, etc. and applying cement slurry at Brushing neat cement slurry with 3.0kg of cement per sqm including necessary scafolding required for carry out work at any height as specified and directed by engr-in-charge complete |
| 2 | M&L for 15mm thick rendering in CM 1:3 over brick / concrete wall surfaces/ceiling sufaces trowelled to even & fair using extra cement and including water proofing compund @ 200 ml per bag of cement for wall surfaces including necessary scafolding required for carry out work at any height as specified and directed by engr-in-charge complete |
| 3 | Cleaning of reinforcementbars upto 10 mm dia from rust of reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry,including necessary scafolding required for carry out work at any height as specified and directed by engr-in-charge completeall complete as per direction of Engineer-In-Charge. |
| 4 | M&L forapplying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB or equivalent of approved make and quality comprises of resin and hardner mixed in equal proportion by volumewith minimum 9-10 hours between the coats,sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment including necessary scafolding required for carry out work at any height as specified and directed by engr-in-charge complete.Note exposed surface of RCC to measeued. |
| 5 | M&L forProviding, mixing and applying bonding coat of approved adhesive on chipped portion of RCC roof as per specifications and direction of Engineer-In-charge complete in all respect. SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer including necessary scafolding required for carry out work at any height as specified and directed by engr-in-charge complete. Make :- STP/Chemsol/Bostik/Choksey/Fosroc as approved by GE |
| 6 | M&L for dismantling , cleaning, removing loose dirt of damaged concrete portion of slab/columns/beams/chajjas/parapet /roof projection/balcony/staircase applying two layers with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch repair mortar Sika monotop 122F (having the technical parameters mentioned in material specifications ) capable of applying up to 20-25mm thick in double layer or multiple layers initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness including necessary scafolding required for carry out work at any height as specified and directed by engr-in-charge complete. Make : STP/Chemsol/Bostik/Chemsol/Choksey/Foscroc as approved by GE. |
| 7 | Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, SmartCare Ultrablock Block 2K Suin 2 coats having 200 % elongation as per ASTM 2370 , resisting 5 bars hyrostatic pressure as per DIN 1048,crack bridging min. 2mm as per EN 1062 -7 :2004.Applying SC Ultra block 2k in two coats in SSD condiition at a coverage of 1.5 kg per sqm .Mixing of powder to Liquid in the ratio of 60:40 parts by weight complete as per manufacturers specifications. |
| 8 | M&L for Finishing walls with Acrylic Smooth exterior paint of required hade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 9 | Supply only Liquid water proofing compound |
| 10 | M&L for plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, with rivetted, bolted or welded attachments conforming to Fe-410W (Gde-E-250) quality Bcomplete |
| 11 | S&F Anchor fasternes of 10mm dia of length 250mm fixed to RCC member with epoxy grount of HILTI Chemicals or equivelent incuding drilling and necessary fixing arragement |
| 12 | Dismantling wrought iron or mild steel work of any description not otherwise provided etc |
| 13 | M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 14 | M & L for applying two coat of synthetic enamel paint on steel surfaces over one coat of zinc primer including preparation of new steel surfaces exceeding 10 cm width or girth |
| 15 | Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level) un-reinforced. |
| 16 | M&L for 75mm thick PCC (1:4:8) type C2 (using 40mm graded stone aggregate) as in sub base/flooring/ paving complete; |
| 17 | M&L for Machine pressed coloured Glossy finish precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade including 30 mm thick grit/stone dust cushioning all as specified. |
| 18 | Dismantling of fencing wire mesh any type |
| 19 | Dismantling posts or struts (Wood, Steel or RCC), any section embedded in concrete, brick work etc. including taking out embedded portion and making good disturbed ground. |
| 20 | S&F Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 |
| 21 | Supply only Chain link MS galvanised fencing, any size or type |
| 22 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire |
| 23 | S &F framed work as in doors or gates of with tube section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and decorative cast iron artical etc. |
| 24 | M&L for mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips |
| 25 | Ditto- all as per item No- 24 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders |
| 26 | M&L for Pre-cast cement concrete block masonry with solid blocks, Type D-5, 1:5:8, exc. 10 cm in width and setting in mortar, complete, built in cement mortar (1:6) all as specified& directed including dismantling of Brickwork or block masonary, built incement mortarb etc, all as specified and directed. . |
| 27 | Taking down cement plaster on stone walls including raking out joints, hacking for key, scrubbing down with water all as specified |
| 28 | M&L for Rendering 15mm thick in cement mortar 1:4 on brick surfaces / concrete finished even smooth with spong finish without using extra cemnet complete all specified and directed. |
| 29 | M&L for Preparation of new plastered surfaces and applyingtwo coats of cement base paint over alkali resistance primer all as specified. |
| 30 | Demolition of cement concrete is reinforced of any description and in any position not otherwise specifically provided for |
| 31 | S&F in repairs galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc. as directed (each line of wire to be measured) |
| 32 | M&L for nominal Mix RCC, type Type B1 1:2:4 using (20 mm graded stone aggregate) in Beams, cantilevers, lintels, columns pillars, piers, posts, struts, chullah hoods, stair case, arches, domes, vaults, shell roofs, arch ribs, folded plates, slabs, balconies, canopies, deck slabs etc. or in similar articles |
| 33 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splaysbetween floors and beams, etc. |
| 34 | M&L for preparation of old decorated surfaces of walls and including applying two coats of cement base paint white or tinted all as directed. |
| 35 | M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of white wash complete all as specified. |
| 36 | S&F Razor concertina coil, 450 mm Dia, consisting of spiral with sharp edged tape crimped to a steel wire duly galvanised with scrapper barb having 51 spirals with 125 clips (when strtched to a length of 6 m) and fixed to MS frame work, with and including provision of one coat of marine paint over a coat of primer provided by the manufacturer, complete all as specified and directed. |
| 37 | Dismantling of stone slab in any description or thickness, laid bedded jointed in any morter. |
| 38 | M&Lfor Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over and including screed bed or bedding layer of 15mm thick in CM (1:6) all as specified and directed by Engineer-in-charge. |
| 39 | Ditto all as per item No 38 here in before but as in skirting including 10mm thick backing coat plaster in CM 1:4 |
| 40 | M&L for precast coloured, chequered cement concrete tiles, glossy finish of size 300 x 300mm x 20mm thick, conforming to IS-1237 (2006) set jointed and pointed in neat cement slurry in floor laid over and including 20mm thickscreedbed in CM (1:6). |
| 41 | M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and applying cement slurry at Brushing neat cement slurry with 3.0kg of cement per sq. m Complete |
| 42 | M&L for PCC in 1:4:8 type D2(using 40 mm graded stone aggregate) in foundation |
| 43 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cmthick, spread, levelled and rammed including watering & Ramming |
| 44 | M&L for Hardcore of gauge n exc. 63 mm, Broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface |
| 45 | M&L for preparation of new plastered surfaces and providing two coat of weather proof exterior emulsion paint on on wall surfaces including primer coat complete. |
| 46 | M&L for preparation of old decorative surfaces and providing one coat of weather proof exterior emulsion paint on walls complete all as specified and directed. |
| 47 | M & L for applying one coat of synthetic enamel paint on steel surfaces of any description not otherwise discribed over 10 cm width of girth including preparation of old painted surfaces complete all as specified. |
| 48 | Dismantling Asbestos cement (corrugated, semicorrugated, etc.)sheets in roof coverings |
| 49 | S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubesconforming to I. S.1161- 1979 grade St.-240 |
| 50 | S&F Pre- painted any pattarn galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws asspecified |
| 51 | S&F, Powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 52 | S&F Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 53 | Supply & Fix4.00 mm thick plain sheet glass, selected quality, in square nexc 0.5 Sqm each pane |
| 54 | S&F Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in eachdoor, hinges, anodised aluminum snap beading screws etc. complete all as specified. |
| 55 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 56 | S&F door closer (aluminium extuded body section) hydreulically regulated, ,designation No 1 universal type, suitable for door shutters up to 700mm in width and of wieght not more than 35Kg complete all as directed. |
| 57 | S&F mild steel 4 Lever mortice lock, vertical type of size 100mm all as directed. |
| 58 | Dismantling Boarding of any description fixed in any position with nails,with or without cover fillets. |
| 59 | S&F3mm thick Aluminium composite panels(ACP) flat or bent panel thatcolour consist of two thin aluminium sheets bonded to a non aluminium core used for external claddingetc. including necessary aluminium frame work Complete all as specified and fixed as per manufacturers instruction . |
| 60 | M&L for Boulder pitching, with using hard broken boudres of granite/trap stone, hand packed tightly complete all as specified and as directed |
| 61 | Demolition of cement concrete of any description & in any position not otherwise specifically provided for. |
| 62 | M&Lfor providing cement concrete (1:2:4) B-1 (using 20 mm graded stone aggregate) as in window cill, copings etc Including necessary form work etc complete all as specified. |
