|
| 1 | Surface dressing in soft loose soil n exc 15 cm deep and getting out. |
| 2 | Excavating in trenches n.exe. 1.5 m width and n.exe. 1.5 m in depth for foundation in soft/loose soil & getting out. |
| 3 | Excavating in trenches exe. 1.5 m width and exc 1.50 m but not exe. 3.00 m in depth for foundation in soft/loose soil & getting out. Mud soil and dewatering in footing |
| 4 | Returning filling in, including spreading, levelling, watering & well ramming in layers not exc 25 cm. |
| 5 | Removing excavated material n exc 50 m & depositing where directed at a level n exc 1.5 m. |
| 6 | M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation. |
| 7 | M&L forM25 RCC designmix using 20 mm graded aggrgate for raft foundation footing ,bases of columns, plinth beams & mass concrete, complete all as specified and directed. |
| 8 | M&L forM25 RCC designmix using 20 mm graded aggregate for columns, pillars,posts and struts, complete all as specified and directed. |
| 9 | M&L forM25 RCC design mix using 20 mm graded aggregate for beams, cantilevers, roof beam , lintels over 1.5 m span, etc, complete all as specified and directed. |
| 10 | M&L forM25 RCC design mix using 20 mm graded aggregate for slab complete all as specified and directed. |
| 11 | M&L forM25 RCC design mix using 20 mm graded aggregate for chajjas , etc, complete all as specified and directed. |
| 12 | M&L for precast reinforced cement concrete cover slabType B1 (1:2:4) ( using 20mm graded aggregate) as in drain cover, manhole cover, etc, complete all as specified and directed. |
| 13 | M & L for TMT reinforcement 10 mm dia and over cut to length bent to shape including cranking, hooking etcbinding with mild steel wire not less than 0.90 mm dia (annealed) all as directed complete. |
| 14 | S & F mild steel TMT bar 5 mm dia and over upto and including 10mm dia in strrups as inincluding cutting, bending and binding with mild steel not less than 0.9 mm dia (annealed) all as directed complete. |
| 15 | Form work for foundation footing , bases of columns & plinth beams similar work vertical or batter. |
| 16 | Form work for side of pillars, posts, columns & similar works vertical or batter. |
| 17 | Form work toside & soffits of floor or roof beams, slab, lintels & similar works. |
| 18 | Form work tosoffits ofroof slab & similar works. |
| 19 | M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed. |
| 20 | M&L for brick work with burnt old size bricks built in cement mortar 1:4 straight or curved on plan to any radius in half thick walls and all as directed. |
| 21 | M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) mixed with WPC ( WPC shall be measured & paid separately |
| 22 | M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth. |
| 23 | M&L rendering 15mm thick on fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth using extra cement |
| 24 | M&L for 20mm thick plaster on fair faces of brick work or concrete surface in cm (1:4) with wpc @2% by weight face of conc work to wall surface and the surface is finished even and smooth without using extra cement |
| 25 | Supply only integral WPC |
| 26 | M&L for rendering 5 mm thick on ceiling or concrete Surfaces in cement mortar 1:3 finished even and smooth. |
| 27 | M&L for 75 mm thickPCC 1:3:6 type C2 using 40mm graded aggregate as in plinth course as directed by Engineer in charge. |
| 28 | M&L Sand filling under floors or in foundations including watering and conosoldiation. |
| 29 | M&L for brocken stone or boulders of hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface. |
| 30 | M&L for 100mm thick PCC type D2 1:4:8 using (40mm gradded aggregate) as in sub base. |
| 31 | M&L for Pre-polished Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and poined in neat cement slurry with grey cement and pigment in floors including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 32 | Glazed ceramic coloured tiles in vertical surfaces 450x 300x 7 mm thick set and jointed in neat cement slurry & painted in white or colour cement to match incl sreed bed 10 mm thick in CM 1:4 . |
| 33 | M&LNon - skidcoloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes. |
| 34 | M&LNon - skidcoloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes. |
| 35 | S&F Pressed steel frames for door with one or more rebates including necessary fixing lugs hinges, lock, strike plate etc.complete for frame of size-105x60mm |
| 36 | M&L for PCC 1:3:6 type C-0 in filling of pressed frame. |
| 37 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor.complete all asapecified and as directed. |
| 38 | S&F 30 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides. |
| 39 | S & F 35 mm thick factory made Second class hard woodkiln seasoned and chemically pressure treated Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. |
| 40 | S&F aluminium frame for doors, windows, ventiletors with one or more rebates including joining cleat for fixing etc complete all as specified incl powder coating above aluminium section.(minimum thickness of powder coating 50 micron). |
| 41 | S&F for window/ventiletor shutters, side hung type without sash bars aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips,ruber neoprene packing,anodised aluminium snap beading screws,anodised aluminium fittings such as peg stays 150 mm long(1 no),hinges type-B-21 100 mm long( 2 no) suitable handle 1 no complete all as specified incl power coating of any colour (thick ness of powder coating not less than 50 micron). |
| 42 | S&F for Aluminium three track sliding window and ventiletor frame Side/Top made up 123.45 mm /44 mm 1.5 mm thick bottom 128.00 mm/ 39.15 mm / 1.63 mmaluminium section & shutter made up 69 mm / 25.40 mm/1.63 mmand 50.80 mm / 25.40 mm/ 1.63 mm thick without sash bar alum sectionincluding all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised alumn fittings,suitable alumn handle and locking arrangment , two track for glass and one track for aluminium wire meshetc as directed by engr in charge. incl powder coating of any colour(thick of powder coating not less than 50 micron) & provision of AC hole as directed.. |
| 43 | S&F 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beadsin squaresexceeding 0.50 Sqm in each pane |
| 44 | Supply and fixINGGI wire cloth with 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium stapple complete all as specified and directed. |
| 45 | S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165 |
| 46 | S & F Solid PVC Door Frame of size 50mmx47 mm made out of 5mm wood grain colour PVC Sheet reinforced with MS Square etc. |
| 47 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S.frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and as directed. |
| 48 | S&F 150mm long aluminium anodised barrel tower bolts of extruded section |
| 49 | S&F aluminium alloy 250mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed. |
| 50 | S&F 100mm MS butt hinges medium weight |
| 51 | S&F aluminium handle cast type anodised 150mm size |
| 52 | M&L three coat ofwhite wash onceiling surface including preparation of new surface complete all as specified and directed. |
| 53 | M&L for applying a coat of 1mm thick wall care putty over plaster surface to prepare the surface even and smooth as per manufacture instruction, complete all as specified and as directed. |
| 54 | M&Lfor preparation of new plastered wall surfaceapplying twocoat of oil bound distemper on wall all as complete all as specified and directed. |
| 55 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 56 | M&L for brushing neat cement slurry with 03 Kg of cement per Sqm |
| 57 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 . (Internal water proof compound measured seperately) |
| 58 | M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced applicationincluding coating the surface with water based bituminous primer blow bitumen of 85/25 or 90/15 at 1.2 Kg/Sqm both at bottom and top of the membrance and finally finished with one coat of bitumenous aluminium paint at 100 gm per sqm complete all as specified. |
| 59 | M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of primer of any description, not otherwise described, over 10cm width or girth, complete all as specified and directed. |
| 60 | M&L Painting two coats of synthetic enamel paint over a coat of red oxide primer to new steel Surfaces of any description, not otherwise described, over 10cm width or girth complete all as specified and directed. |
| 61 | Supply fix in repairs Harrison rails, mild steel, chromium plated fixed alongwith 2 Nos. of brackets, stops, rollers etc, complete all as specified. |
| 62 | Supply and laying 20 mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 63 | Supply and laying 25 mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 64 | S&F 25 mm Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed |
| 65 | S&F 500 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position all as specified including 20mm bore ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed. |
| 66 | S&F 15mm bore bib tap cast copper alloy fancy type chromium plate with crutch or butter fly handle screwed down for iron pipe but fancy type. |
| 67 | S&F 15mm bore stop cock/valve cast copper alloyscrewed down high pressure with crutch or butter fly handle screwed both end for iron pipe complete. |
| 68 | S&F PVC connector 600mm long with brass coupling in both ends screwed down for iron pipe. |
| 69 | S&F10 litre capacity PVCtype low level flushing cistern with inlet ball valve, float and handle/push flush type brackets etc complete . |
| 70 | S&Fin repair vitreous china, orrisa squatting pan of pattern water closetseat of size 580mm x 440mm white with and incl\"P\" or \"S\" trap and provision of lime concrete bedding in repairs |
| 71 | S&F 15mm borepiller tap fancy type castcopper alloy with capstin head CP screwed down high pressure with or without littered \"H\" or \"C\" with long screwed shank and fly nuts screwed for iron pipe etc complete. |
| 72 | S&F vitreous china wash basinwhite, flat back, size 550x400mm excluding taps , waste ,but including barkets. |
| 73 | S&F 32mm bore dia Waste coupling of PTMT (half or full threaded) minium weight 45 gms) |
| 74 | S&F 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromimum plated brass screws and cup washers. |
| 75 | S&F 100mm dia PTMT grating. |
| 76 | S&F 75 mm thick PVC (SWR pipes single socketed in any length with rubber ring joints laid in trenches or floors. |
| 77 | M&L 100 mm bore for cast iron Nahani trap with grating incl jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) |
| 78 | S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes double socketed in any length with rubber ring joints fixed in walls. |
| 79 | S & F 110 mm bore PVC (SWR) bends of any radius. |
| 80 | S & F 110 mm bore PVC (SWR) Vent Cowl |
| 81 | Supplying, laying and testing of 150 mm internal dia of double wall corrugaed (DWC) high density polythylene pipe (HDPE) and stiffness classes 8 (SN-8) with ISI marked (With CML No ) with and including all fittings & jointing materials for connection of inspection chamber/WC to first manhole of the sewage line complete all as specified and directed.. |
| 82 | Cutting into existing manholes of 150 mm dia for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required. |
| 83 | M & L brick work with sub class -B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4. all as specified and directed |
| 84 | M&L for preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm over 1mm thick wall care putty complete as directed. ( Note: WPC shall be measured and paid seperately) |
| 85 | M&L 75 mm thick 1:3:6,Type C-I (using 20mm graded agg) in plinth protection etc.laid in alternate bays all complete and as specified. |
| 86 | M&L75 mm thick Cement concrete1:4:8 type D-2 (using 40 mm graded agg) as in sub base complete all as specified and directed. |
| 87 | Material andlabour for premium quality, vitrified ceramic tiles, exc of 0.42 Sqm n.exc 1Sqm10mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and includingcement screed bed 15mm thick in cement mortar (1:6) base complete all as specified and directed. |
| 88 | Material andlabour for premium quality, vitrified ceramic tiles, exc of 0.42 Sqm n.exc 1Sqm10mm thick thick as in skirting, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and includingcement plaster 10mm thick in cement mortar (1:4) complete all as specified and directed. |
| 89 | Supply and fix anodised aluminiumthree track sliding windowand ventilator frame side/top/shutters (weight of section not less that 0.55 Kg/RM) aluminium section withoutsash baraluminiumsection including all necessary joining cleats,hold fast, rubber gasket anodised snap beading, anodisedaluminiumfittings, suitable alum handle and locking arrangement etc, two track for glass and one track for aluminium wire mess etc, including powder coated of any colour (thick of power coating not less than 50 micron) & providing AC hole complete all as specified and directed.. Note:- (i) Wire cloth /glass shall be measured and paid separately at SUPPLY only rates under appropiate items. (ii) Labour charges for fixing of wire cloth/glass panes is demeed to be included in unit the unit rate quoted. |
| 90 | S & F 5.5 mm thick frosted glass, ordinary quality and glazing with aluminiumbeadsin squares not exceeding 0.5 Sq. M in each pane |
| 91 | S & F 4 mm thick Sheet glass, ordinary quality and glazing with necessary aluminiumbeadsin squares not exceeding 0.5 Sq. M in each pane |
| 92 | Supplyand fixedstainless steel wire cloth with 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with a stainless steel stapple complete all as specified and directed. |
| 93 | M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 . (Internal water proof compound measured seperately) |
| 94 | M&L for roof treatment with the following specification - applying water proofing treatment on horizontal or vertical surfaces by applying oil bound bitumen primer @ 0.20 Kg/sqm and providing 3mm thick APP modified water proofing membrane weighing not less than 3 Kg/sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm, The overlap shall be minimum 100mm on transverse direction and 75 mm on longitudinal direction and sealing overlap by torch application and bonded and applying a coat of blown grade hot bitumen 85/25 over and below the membrane @ 1.20 Kg/sqm in drying over the membrane finished with solar reflective bituminous aluminium paint/ primer @ 0.10 Kg/sqm over RCC roof slab/ parapet after cleaning the surfaces by removing dust, dirt etc. as per manufacturer’s instructionsand all as specified and as directed.NOTE :- The work shall be executed at site by the authorised applicator of APP and as approved by the GE. |
| 95 | M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface areacomplete all as directed. |
| 96 | M&L forTreating the backfill in contact with foundation at the rate of 7.5 litres ofemulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as directed. |
| 97 | M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surfacecomplete all as directed. |
| 98 | M&L forTreating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface areacomplete all as directed. |
| 99 | M & L for 18/19 mm thick pre laminated Particle board one side coloured and other side white for cabinet shutters purpose , fixed with nails,piano hing 30mm width and staple, safety type, brass with aluminium anodisedhinge pin including bolt to hinge plate and fixed with screws all as specified and as directed. |
| 100 | M&L for Spreading and levelling in layers n exc. 25 cm thick and watering and well ramming under floor complete all as specified and directed. |
| 101 | Material and labour for point wiring with 1.5 sqmm (nominal area) FRLSH PVC insulated stranded copper conductor single core including PVC conduit of appropriate size concealed in wall, pressed steel concealed terminal boxes of required size and with top cover 3 mm thick of plastic laminated sheet of reqd colour, painting terminal boxes inside and out side with one coat red oxide primer complete with all accessories and all as specified including 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper earth conductor to common earth and connected to earth dollyfor fan / light / exhaust fan/ bell point controlled by one switch. Note:-1. Cost of PVC conduit, steel terminal boxes, plastic laminated sheet cover etc; are deemed to be included in the quoted rate.2. Cutting chases on walls / ceilingand making good disturbed surfaces including finishing with cement mortar (1:3)and ,putty and plastic paint matching with existing surfaceetc; shall be deemed to be included in the rate quoted above. :(a) One light point controlled by one, one way switch 5 Amps |
| 102 | (b) One 3 point 5 Amps socket outlets point controlled by one switch on the same board |
| 103 | (c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board |
| 104 | All as per item No 101 above but with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board. |
| 105 | S & F Switch piano (White)flush type single pole one way 5 Amp, 230 Volts complete all as specified. |
| 106 | S & F Socket outlet (White)2 in 1,5/6 pin, 5 Amps complete all as specified and directed. |
| 107 | S & F Switch socket combination (White)flush type multipurpose 5/6 pin 5 Amps two in one , 230volts complete all as specified . |
| 108 | S&F Switch socket combination (White)2 in 1 5/6 pin, 15 Amp flush type universal. |
| 109 | S&F ceilling rose (White)three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all specified . |
| 110 | S & F ceiling fan regulator (White)step type, flush type heavy duty suitable to work on 230 Volt AC supply complete all as specified. |
| 111 | S & FLamp holder (White)with insulated body, with back plate suitable for batten fittingscomplete all as directed. |
| 112 | S & F LED ADORE 10 W B22 CDL 5 STAR LAMPwith B 22 base capacity 1200 lumencomplete all as specified.Make-Make- Havells, Cat No: LHLDEUEBML8Z010 or equivalent in Crompton /Philips / Surya. |
| 113 | S & F sheet metal enclosure MCBDBSPN8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified. Make-L&T/ Schneider/ Legrand / Seimens |
| 114 | S & F MCB Double Pole 32 Amps 240/415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed.Make-L&T/ Schneider/ Legrand / Seimens |
| 115 | S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed. Make-L&T/ Schneider/ Legrand / Seimens |
| 116 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorativeultra slim round profile LED lighting fixture with extruded polycarbonate , environmental friendlyenergy efficiebt ready to use packwith driver, holder including LED tube lightconnecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.Make :- Model No. LHEXAPP7UN1W020 ofHavells or Equivalent in Surya / Crompton / Philips |
| 117 | S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 20 watts with pre wired andnecessary mounting arrangements, provision of new 3 core multistrandedcopper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Havells Cat Part No. LHEXAYP7PN6K020 or equivalent in/CG/Surya / Philips |
| 118 | Supply and fixing ceiling fans complete with blades, down rods, electronicregulator , fan hook and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFMwith service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) complete all as specified and directed. |
| 119 | Supply and fix exhaust fan, steel bodyAC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed . |
| 120 | S & F sheet metal enclosure MCBDBSPN4 way with 200 Amps rated bus bar 415 volts double door with magnitic locking system complete including grouted on walls all as specified. |
| 121 | S & F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 93 amps complete all as specified and directed. |
| 122 | S & F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 40 amps complete all as specified and directed. |
| 123 | S & F exhaust fan, steel body AC single Phase. 230V of size 380m sweep with blades, frame and lauvers making suitable size hole as per size of exhaust fan duly with finish as per existing surface complete all as specified and directed |
| 124 | M & L Submain wiring with 4 runs of single core 6 sqmm PVC insulated FRLSH unsheated multistranded 1100 volts grade with copper conducter drawn through and including non-metalic rigid PVC concealled conduit ISI marked and its accessories including one run of single core 6 sqmm PVC insulated FRLSH unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board complete all as specified and directed. |
| 125 | M & L Submain wiring with 2 runs of single core 6 sqmm PVC insulated unsheated (FRLSH) multistranded 1100 volts grade with copper conducter duly chases on walls and drawn through and including non-metalic rigid PVC conduit ISI marked and its accessories including one run of single core 6 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main boardwith proper copper lugs and making good disturbed surfaces and matching with existingcolour complete all as specified and directed. |
| 126 | M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as directed. |
| 127 | Supply & Laying well burnt brick , locally available best quality (sub class \"B\" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified. |
| 128 | Supply & Laying XLPE LT heavy duty UG Cable of size 16 Sqmm 2 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed. Make :- Polycab / Havells / RR Kabel / Gloster |
| 129 | S & F GI Tubing light grade of size 40mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc all as specified and directed. |
| 130 | Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item. |
| 131 | Material and labour for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GIearth wire 4 mm dia connected tomain earthing lead from earth electrode to test point upto 7.5 metre drawn through and including GI protection pipe of light grade 15 mmbore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I. |
| 132 | S&F in repairs3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 50 mm Outer dia, ISI marked, SDR 7.4, PN 16 and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed. |
| 133 | S&F in repairs 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 32mm Outer dia, ISI marked, SDR 7.4 , PN 16and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed. |
| 134 | S&F in repairs PP-R Gate Valves (Brass Insert) 32mm Outer dia and fixed including taking down of existing unserviceable One, complete all specified and as directed. |
| 135 | S&F in repairsPP-R Gate Valves (Brass Insert) 50 mm Outer dia and fixed including taking down of existing unserviceable One, complete all specified and as directed. |
| 136 | Making connection of PP-R distribution branch with PP-R main of 63 mm size by providing and fixing tee of 63 mm x 50 mm including cutting and making fusion joint etc all as specified and directed. |
| 137 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. |
| 138 | M&L for broken stone and bolder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc. all as specified and directed. |
| 139 | M&L For100 mm thick PCC Type C-2 1:3:6 using (40 mm graded aggregate) as in sub base all as specified and directed. |
| 140 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete |
| 141 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 142 | Cement concrete in surface channels and drains Type D2 1:3:6 (40 mm graded aggregate) |
| 143 | M&L for brick work with sub class ‘B’ bricks straight or curved on plan exc. 6 mtr mean radius built in CM(1:4) |
| 144 | M&L for 15 mm thick plaster in cm (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement. |
| 145 | M&L for Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges , copings, kneelers, water troughs and the like including weathering, slightly rounded or chamfered angles and throating,TypeB0 1:2:4 (12.5mmgraded aggregate)as directed |
