|
| 1 | Taking downcement or cement lime plaster of any description on brick, block or stone walls etc (at any height) including racking out joints, hacking for key scrubbing down with water etc complete & removing debris outside MD land as directed. |
| 2 | M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement etc complete all as specified and as directed. |
| 3 | M&L for 15mm thick plaster in CM 1:4 (using water proofing liquid as per manufacturers instructions) on other than fair faces of brick work masonary surface or concrete surface finished even and fair without using extra cement complete all as specified and directed. |
| 4 | M&L for brickwork with fly ash bricks, straight or curved on plan, exc 6 m mean redius,built in cement mortar 1:6 with and including demolition of existing brick work built in cement or cement lime mortarof any description complete all as specified and as directed. |
| 5 | M&L for preparation of new plastered internal surfaces of wall and applying two coat ofacrylic distemper of required shade and colour complete including one coat of primeras per manufacturer\"s specifications in any colour complete all as specified and directed. |
| 6 | M&L for newly plastered wall surfaces, preparation of surface and applying applying two coats of 100% premium exterior acrylic emulsion paint (weather coat) alkali & fungal resistance, dirt resistance of required shade over and including priming coat of exterior primer complete all as specified and as directed. |
| 7 | M&L for preparation of new plastered surfaces or previously untreated surface of wall and applying two coats of cement base paint over one coat ofalkali resistant primercement completeall as specified and as directed. |
| 8 | M&L for preparation of newly plastered surfaces and applying three coats of white wash on wall complete all as specified and directed. |
| 9 | M&L for applying 1.5 mmthick of Birla/ JK wall care putty in new or old decorated surfaces of walls and sanding the surfaces till smooth finish is obtained for receiving finishes complete all as specified and as directed |
| 10 | M&L for Preparation of old decorated surfaces of walls and applying two coats of white washcomplete all as specified and as directed |
| 11 | M&L for Preparation of old decorated surfaces of walls by washing, rubbing down and stopping of painted surfaces, etc and applying one coat of cement base paint, in any colorcomplete all as specified and as directed. |
| 12 | M&L for preparing of old surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying two coats of acrylic distemper in any colour complete all as specified and as directed. |
| 13 | M&L for complete removal of existing treatment on old decorated plastered suface of externalwalls including filling cracks using acrylic wall crack filler & applying two coats ofExterior Acrylic Emulsion paint, alkali & fungal resistance, dirt resistance of required shade over one coat of primer as requiredcomplete all as specified & directed by Engr in charge. |
| 14 | M&L for rolled mild steel work angle iron as in door frame (Chowkhats) & cooler stand confirming to Fe-290 (Gde E165) including preparing back of chowkhat and similar applying two coats of tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and as directed. |
| 15 | M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 16 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removingrubbish off the premises all as specified and directed. |
| 17 | M&L for coloured non-skid ceramic tiles, 7 to 8 mm thick (square or rectangular), area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over & including 15 mm thick screed bed in cement mortar 1:6complete all as specified and as directed.Note :- Colour and shade shall be approved by Engr-in-Charge. |
| 18 | M&L for glazed coloured ceramic tiles in vertical surfaces as dado of size 450x300x6-7mm, thick set and jointed in neat cementand pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on other than fair faces of brick work etc complete all as specified & as directed.Note: Color, size and shade shall be as approved by Engineer-in-charge |
| 19 | Dismantling kota, granite, cudappa stone slabsand interlocking tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortor complete all as specified and as directed. |
| 20 | M&L for machine cut Kota stone flooring 18 to 22 mm thick(minimum size of kota stone slab 22\"x22\") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed. |
| 21 | All as per item No. 20.00 here-in-beforebut 15-18 mm thick as in risers to steps andskirtinglaid over and including backing coat of 10mm thick cement mortar 1:3all as specified and as directed.Note : Riser provided to steps shall be in one piece. |
| 22 | M&L for 18-20mm thick marble (of any type) workas in border strips of 100-150 mm width in kota stone flooring and like in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete all as specified & as directed. Note:- Colour/shade shall be as approved by GE / Engineer-in-Charge. |
| 23 | M & L for 18-20mm thick prepolished Granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/plateform, gate pillars, cills etc or on vertical surfaces including vertical projections, including full round mouldings the edges laid over and over and including screed bed 15mm thick in cement mortar 1:4 jointing, pointing in white cement 1:2 using marble dust with admixture of pigments to match the shade of granite and rubbing polishing to achieve mirror finishcomplete all as specified & directed. Note:- Colour/shade to be decided by Engineer-in-Charge. |
| 24 | Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 25 | M&L for 75mm thick plain cement concrete 1:4:8typeD-2, using 40 mm graded stone aggregate as in sub base of floors and pavingsall as specified and as directed. |
| 26 | M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smoothwithout using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic jointfilling at every 3m length and at corners complete all as specified and as directed. |
| 27 | M&L for PCC 25 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate as in levelling course infloors, roofcomplete all as specified & directed. |
| 28 | M&L for 60mm thick, factory made, chamfered edge, cement concrete interlocking paver blocks (glossy/ rubber matt finish) of M-35 grade with approved colour, design & pattern of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks asrequired size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.Note : Size, shape, pattern and shade shall be asapproved by Engineer-in-Charge. |
| 29 | Taking down chowkats or frames with shutters (without taking off shutters from the frames), area exc 1.50 sqm but n exc 4 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and asdirected. |
| 30 | Taking down chowkats or frames with shutters (without taking off shutters from the frames), area n.exc 1.50 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and asdirected. |
| 31 | Taking down shutters of any description area exc 1 sqm & n.exc 2 sqm each leaf and complete all as specified & as directed. |
| 32 | M & L cement concrete type B-0 1:2:4 (12.5 mm graded agg) as in bed block ,hold fast, coping and similar work etc complete all as specified and as directed. |
| 33 | S&F 35 mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressuretreated all as specified and as directed. |
| 34 | S&F 35mm thick IInd class hard wood glazed skelton shutters,factory made,open rebated and prepared to recive glass,guage etc,(with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of sutters as specified in SSR part - I section - 8, clause 8.20 (a). S&F to chowkhat complete all as specified and as directed. |
| 35 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specified and as directed.Note: (i) Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door/window frames. Variation in profile dimensions on plus side shall be acceptable without any extra cost to the department |
| 36 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges shall be paid separately under respective item. |
| 37 | S & F powder coated aluminum windows, three track, made out of aluminium sectionsincluding all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a)Window frame:(i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m)(ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m)(b)Shutter: (i)Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)Note :Shade shall be as approved by Engineer-in-Charge. |
| 38 | S&F mild steel framed work such as grill, gratings, guard barsetc with end of bars shouldered and/or riveted or forged into spikes, ladders, iron frame, balusters, railings, cooler stand and similar works conforming to Fe.290, Gde-E-165including one shop coat of zinc chrome primer and cutting holes/making surface good in cement concrete 1:2:4 type B-0 complete all as specified and as directed. |
| 39 | M&L for preparing the new wooden surface & applying two coats of synthetic enamel paint (1st grade) over one coat of pink primer over 10Cm width or girth complete all as spd & directed. |
| 40 | M&L for preparation of new steel surfaces over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 41 | S&F SS wire cloth0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames withtinned tacks or galvanized wire staple & complete all as specified and as directed. |
| 42 | S&Fdoor stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor over all length of cover plate 150 mm all as specified and directed. |
| 43 | S&F mild steel helical door spring 300mm ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed by Engr-in-charge. |
| 44 | S&F 100 mm long SS butt hinges, medium weight, cold rolled, ISI marked, complete all as specified and as directed. |
| 45 | Supply & fix only 100 mm longmild steelbutt hinges, medium weight, cold rolled and fixed with screws/welded complete all as specified and directed. |
| 46 | S&F 125mm size aluminium alloy handles, fabricated type extruded section, ISI markedcomplete all as specified and as directed. |
| 47 | S&F aluminum anodized barrel tower bolt of extruded section size of bolt 200mm as specified and directed. |
| 48 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 49 | Taking up or down 15 mm bore dia GI steel tubing and connectionscomplete all as specified and as directed. |
| 50 | Taking up or down 20 mm bore dia GI steel tubing and connectionscomplete all as specified and as directed. |
| 51 | M&L for 15mm bore CPVC pipesSDR 11 & Plain CPVC SDR 11 fittings such as socket, elbow, bends, tee, reucer, union, caps plug, nipple etc complete laid in walls/ceilings or laying in floor trench or fixed to walls complete all as specified and as directed |
| 52 | M&L for 20mm bore CPVC pipesSDR 11 & Plain CPVC SDR 11 fittings such as socket, elbow, bends, tee, reucer, union, caps plug, nipple etc complete laid in walls/ceilings or laying in floor trench or fixed to walls complete all as specified and as directed |
| 53 | S&F in repairs Vitreous China wash basin, white, of size 550x400mm including brackets, Waste Pipe, CP Waste coupling 32mm of bore, PVC connection pipe complete all as specified and directed.Note : Cat No S2040141 of CERA or equivalent model of makes Specified. |
| 54 | S&F in repair Vitreous China, white Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) includingtrap, and flushing pipeanti syphonage pipe ,set in cement concrete as specified complete all as specified and directed. |
| 55 | S&F in repair PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacityWhite, with inlet ball valve, float, handlewith 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.Note : Cat No B1010110 of CERA or equivalent model of makes Specified. |
| 56 | S & F stainless steel grating with square frame (grating thickness 1mm and frame thickness 1.5mm) of size 125mm (minimum) with waste hole complete all as directed. |
| 57 | S&F in repair Soap dish, chromium plated, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed. |
| 58 | S&F in repairs, 15mm bore stop valve, angle valve of cast copper alloy, fancy type , chromium plated, long body (concealed type) high pressure screwed for iron pipe complete all as specified and as directed.Make: Cera Cat Part No-F1015361CH or equivalent model of makes specified. |
| 59 | S&F in repair over head shower roses 125mm size with 200mm long shower arm and wall flange all as specified and directed by Engr-in-charge.Make :- Cat No F7020111AB of Cera or equivalent model of makes specified. |
| 60 | S&F in repairs, angle/ stop cock 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.Make :- Cat No F1015201 of Cera or equivalent model of makes specified. |
| 61 | S&F in repairs, bib tap 15mm dia, with wall flange and areator screws down for iron pipe or for iron pipe or for brass ferrule complete all as specified and as directed.Make :- Cat No F1015151 of Cera or equivalent model of makes specified. |
| 62 | S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered \"HOT\" or \"COLD\" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.Make : Cat No.F2014101 of CERA or equivalent model of makes specified. |
| 63 | S&F in repairstowel rail60 cm long between flangescomplete all as specified and as directed.Make : Cat No. F5015103CH of CERA or equivalent model of makes specified. |
| 64 | S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all asspecified and directed by Engr-in-Charge |
| 65 | S&F in repair bevelled edge looking mirror 5.5mm thick ofsize 600mm x 450mm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screwscomplete all as specified anddirected by Engr-in-charge. |
| 66 | S&Fin repairs, rotational moulded polyethylene water storage tanks colour white(cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia float valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed. |
| 67 | S&Fin repairs, rotational moulded polyethylene water storage tanks colour white(cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia float valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed. |
| 68 | S&Fin repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20mm dia, ISI marked complete all as specified & as directed. |
| 69 | S&F in repairs, 20mm dia stainless steel curtain rod with brackets and finials at both ends as per site requirement including taking down old curtain rods with accessoriescomplete all as specified and as directed.Note :- The Cost of brackets and knobs shall deemed to be included in the quoted rate. |
| 70 | S&F in repairs 75 mm dia PVC(SWR) nahani/ floor trap withgrating including jointing to waste pipe with solvent cement complete all as specified and as directed. |
| 71 | S&F in repair for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed. |
| 72 | Dismantling asbestos cement sheet (corrugated or semi corrugated etc) including ridges in large patches as in roof covering complete all as specified and as directed.Note:- Dismantling existing wind tie and refixing the same where required for taking down ofsheets shall deemed to be included in the unit rate quoted . |
| 73 | Dismantling of mangalore pattern or similar tiles in roofing complete all as specified and directed. |
| 74 | Dismantling wooden battens for tiles, shingles etc, of any size including tilting fillets spaced not exc 15 cmcomplete all as specified and directed. |
| 75 | Dismantling timber scantlings 40 sqcm and over in section, in any position, such as in rafter, purlin etc as inunframed work, complete all as specified and as directed. |
| 76 | Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 Sqcm in section, in any position, complete all as specified and as directed. |
| 77 | Cutting holes into or through brick wall built in cement lime mortar and walls of cement concreteof superficial area exc 150 sqcm but n exc 400 sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified & as directed by Engr-in-Charge. |
| 78 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 79 | S&F prepainted galvalume aluminium zinc coated galvanised iron based corrugated steel sheets0.5 mm thick of any colour, AZ 150 coating having tensile strength 550 MPA as in roof covering orridges with side lap and end laps, hips and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed. Note:- Colour & Pattern to be approved by Engineer-in-Charge. |
| 80 | S&F pre-painted galvalume aluminium zinc coated galvanised Iron based Plain steel sheets, 0.5mm thick of any colour, AZ150, with side lap and end lap having tensile strength 550 MPA as in ridges, hips, valley gutters, drip and straight flashingfixed with self taping screws (length & girth as fixed) complete all as specified and as directed. |
| 81 | S&F laminated Gypsum tile board 8mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceilingas per manufacturers instructions of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mm center to center to form a |
| 82 | grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, including dismantling existing false ceiling work of any description complete all as specified and as directed.. |
| 83 | S&F Steel work in Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed. |
| 84 | M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs in lintels upto 1.5 m clear span, cills, steps ; seismic and other similar bands , plinth courses , string courses lacing courses, parapets and railings coping ,kneelers , apex stones , bed plates ,water throughs and the like includingweathering , slightly rounded or chemfered angles and throating complete all as specified and as directed . |
| 85 | S&F rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe-410W grade E-250 quality-B with and including one shop coat of zinc chrome primer including preparation of new surfaces complete all as specified and as directed. |
| 86 | Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc and matching with existing surface complete all as specified and as directed. |
| 87 | M&L for point wiringcomplete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990,PVC insulated andunsheathed , FRLS cabledrawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmmcopper conductor cable (multistranded)PVC insulated and unsheathed FRLS cableas earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards/bakelite sheetsfor mounting switches, sockets, fan Regulators, accessories etc as specified and as directed for one light point or one fan point controlled by one, one way switch |
| 88 | NOTES: (a)Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW, BLUE for Earth-Green and Neutral-Black) (b) All points shall be earthed up to fixtures i.e holders, tube lights, all lights, ceiling lights, bulkhead lights, bldg security lights etc. |
| 89 | All as per serial item No 86.00 but for one bell / buzzerpointcontrolled by one push button on the same board with other switches or independent board |
| 90 | All as per serial item No 86.00but for one 3 pin 6 Amp Socket outlet point on same board with other switches including earth wire as per description given above and connected to common earth and earth terminals. |
| 91 | All as per serial item No 86.00 but for one 3 pin 6 Amp Socket outlet point on independent board including earth wire as per description given above and connected to common earth and earth terminals. |
| 92 | All as per serial item No 86.00but with 2.5 Sqmm cables for one 16A, 6-Pin (multipurpose) socket outlet pointon independent board with & including 2.5 Sqmm FRLS (H) cable as earth wire complete all as specified and as directed. |
| 93 | S&F Modular switch single pole one way6/10 Amps 1 module complete all as specified and as directed. |
| 94 | S&F Modular switch single pole one way 16 Amps 1 module complete all as specified and directed. |
| 95 | S&F ModularBell Switch 5/6 Amp 1 Modulecomplete all as specified and as directed. |
| 96 | S&F Modular socket 6 Amp-2/3 pin combined 2module complete all as specified and as directed. |
| 97 | S&F Modularsocket 6 A/16 Amp -2/3 pin combined 2 module complete all as specified and as directed. |
| 98 | S&F Modular fan regulator Step Type, 120W-2 Module suitable for BLDC ceiling fan 1200/1400mm sweep Complete all as specified and as directed. |
| 99 | S&F in replacement decorative ultra slim batten square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficientof capacity 20 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make : Cat No.LHEXAWP7UN1W020 of Havells or equivalent of makes specified in PS |
| 100 | S&F in replacement decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficientof capacity 10 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make : Cat No.LHEXAZP7PN1W010 of Havells or equivalent of makes specified in PS |
| 101 | S&F in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. |
| 102 | S&F in replacement LED light fitting 1x 9W / 1X10W bulkhead luminaires including LED light driver holder connecting up with two core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 103 | S&F ceiling rose surface bakelite three terminal type complete all as specified and as directed. |
| 104 | S&F in replacement of bell multi music type, AC, 230 volts, single phase complete all as specified and as directed. |
| 105 | S&F in repairs, MCB DB, double doortype(when MCBs are to be used),single pole and neutral, 240 volts, 8 way,protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copperbusbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed. |
| 106 | S&F in repairs, MCB DB, double doortype(when MCBs are to be used), single pole and neutral, 240 volts,4 way,protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copperbusbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed. |
| 107 | S&F in replacement of MCB SP, C Curve, 6 to 32 Amps 10 KA single pole AC 230volts complete all as specified and as directed. |
| 108 | S&F in replacement of MCB SPN, C Curve, 40-63 Amps 10 KA single pole AC 230volts completeall as specified and as directed. |
| 109 | Supply & fix lamp LED 9/10 Watt, 230 volts 50 Hz AC complete all as specified and as directed.Make : Cat No. LHLDDEBNL5R10 of Havells or equivalent of makes specified in PS |
| 110 | Supply & fix Emergency/Inverter lamp in replacement of old Bulb any typewith Emergency Back up up to 3-4 Hrs High grade thermal plastic housing with Al Heat sink for better thermal management , 100 lumen/watt PF>0.90 operating voltage 100 to 300 V Eco friendly (No Mercury) CCT 6500 of capacity 12 watt complete all as specified and directed.Make : Cat No.LED 12 W B22 CDL INVERTER BULB V2 of Havells or equivalent of makes specified in PS |
| 111 | S&F in replacement Emergency / Inverter LED batten 20W 6500K with square profile and polycarbonate channel, lithium-Ion battery with charging time 8hours-10 hours, back up time up to 4 hours and surge protection up to 4KV including connecting up with suitable flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make : Cat No. LHEXASP7IN1W020 Pride Plus Inverter Batten 20W 6500 KV1 of Havells or equivalent of makes specified in PS |
| 112 | M&L for sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including suitable size heavy grade casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduit complete all as specified and as directed.NOTES: (a) Proper colour coding shalladopted for wiring (for phase-RED, YELLOW, BLUE for Earth- Green and Neutral-Black) (b) Three runs of 4 sq.mm cable and one run of PVC casing & caping shall be measured as one unit. |
| 113 | M&L for sub main wiring with 2 runs of 2.5 sqmm, single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including suitable size heavy grade casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduit complete all as specified and as directed.NOTES: (a) Proper colour coding shalladopted for wiring (for phase-RED, YELLOW, BLUE for Earth- Green and Neutral-Black) (b) Three runs of 2.5 sq.mm cable and one run of PVC casing & caping shall be measured as one unit. |
| 114 | Supply, laying,testing and commissioning of UG LT cables, 50 Sqmm x 3.5 core, 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded aluminium conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/MDB in building etc to suit the cableincluding material and labour for all jointing/connecting material as requiredsize, cables laid in trenches/ducts/under plinth floors passing through pipes etc, fixed on wall including taking out old cable and cable covers complete all as specified and directed. |
| 115 | Supply, laying,testing and commissioning of UG LT cables,10 Sqmm x 2.0 core, 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded aluminium conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/MDB in building etc to suit the cableincluding material and labour for all jointing/connecting material as requiredsize, cables laid in trenches/ducts/under plinth floors passing through pipes etc, fixed on wall including taking out old cable and cable covers complete all as specified and directed. |
| 116 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc or for shafts, wells, manholes, pier holes, laying of cable& pipes etc not exceeding 10 sq m on plan not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and as directed. |
| 117 | Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick as in soil complete all as specified and as directed. |
| 118 | Removing excavated surplus soil to a distance n.exc. 50 mand depositing where directed at a level not exceeding 1.5 m from the starting point complete all as specified and as directed. |
| 119 | Supply and laying Double Walled Corrugated (DWC) HDPE pipe of nominal bore 63mm including 90 degree bends with coupler and rubber ring, conforming to IS :16205 Part 24 Type 450N, laid in trenches for cable protection complete, all as specified and as directed. |
| 120 | M&L in replacement for GI tubing 40 mm bore light grade for protection of cable with all necessary fittings accessories such as MS 40x3mm clamps of suitable length, nuts, bolts and washers and fixed complete towall/ceiling or laid under floors complete all as specified and as directed. |
| 121 | S&Fin replacement 35 Wattbuilding mounted LED security light fitting complete made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2m long bend to shape requiredfixed to pole / wall with 02 Nos MS clamps made out of flat iron 40x5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting complete all as specified and as directed.Make : Havells Cat No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model of makes specified. |
| 122 | M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia, by means of nut bolts, check nuts and washer andthe GIEarth wire connected upto main earth point/DBs alongwith 15mm dia GI medium grade protection pipeincluding provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4)cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape,GI light grade |
| 123 | 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh andearth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.Note : Rate of GI earthwire and GI protection pipe upto 7.5 mtr length shall be deemed to be included in this item |
