|
| 1 | Dismantling of Asbestos cement (corrugated, semi corrugated etc,) sheets in roof coverings etc complete all as specified and directed. |
| 2 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, molding / folding in circular / semicircular of any position and height fixed with self tapping screws as specified, as directed by Engr-in-charge |
| 3 | Description all as per item No 02.00 here in before but plain sheet as in ridge/valley/gutter complete all as specified and as directed. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 5 | S&F mild steel rolled sections, Framed work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, using FE-290 (Gde-E-165) complete all as specified and directed. |
| 6 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame worketc completeall as specified and as directed. |
| 7 | S&F Solid PVC Wall lining consisting of 5mm thick wood grain printedPVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed. |
| 8 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive offixing on to wall to make PVC Frame acomplete all as specified and directed. |
| 9 | Providing and fixing PVC fluted wall panels of approved make, design, and shade, made from rigid Polyvinyl Chloride (PVC), extruded with vertical/ribbed/fluted profile, having a panel width 128mm x 18mm with 2mm groove at 14mm pitch, and length as required at site and back of panels are perforted with a nonwoven fabric covering of 0.2mm for providing sound absorption via the accoustic impendance method (confirming to IS 12406 and laminated panel confirming to IS 14587), fixed over a prepared surface using suitable adhesive, screws, or concealed clip system as per manufacturer’s specification. Panels shall be moisture-resistant, termite-proof, fire-retardant. All joints, corners, and terminations shall be finished with matching PVC trims and accessories. Work includes surface preparation, edge finishing, and accessories such as corner profiles, end caps, adhesive, scaffolding, and cleaning of surface after installation, complete in all respects as per drawing and direction of the Engineer-in-Charge. |
| 10 | M&L false ceiling using powder coated grid system of GI modular grid size 600 x 600 mm with runner 38x24x07 mm cross tee 25x24x0.7 mm and wall angle 24x24x7-8 mm thick PVC laminated Gypsum tiles of size 600 x 600 mm of different designs with rear side MPL film fitted in the grid, grid system hanges by 6 mm dia GI wire to purlin, trusses; RCC slab of the roof etc. with hold down clips, butterfly clips, height fixtures etc, complete all as specified and directed. |
| 11 | S&FGRG (Glass fibre reinforced Gypsum) semi perforated 12 mm thick tiles of size 595 x 595 mm white colour of approved texture,design (Tegular) and patterns having moisture content less than 2%, humidity ressitance of 99% NRC 0.60 to 0.85 as per IS 8225:1987, Non combustible as per BS 476 Sub Head : 26.0 New Technologies and materials reflectance of 85% (Min) to be laid in true horizontal level suspended on interlocking metal \"T\" grid of hot dipped galvanised iron section of 0.33 mm thick (galvanised @ 120grams per sqm including both sides) comprising of main \"T\" runners of size 15 x 32 mm of length 3000mm,cross Tof size 15 x 32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items(galvanised @ 80 grams per sqm ) i e 50mm long, 8mm outer diameter M-6 dash fasteners,6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x2 mm. Galvanised iron perimeter wall angle of size 24 x 24 x0.40mm thick of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and as directed. (Make- Dimond/ Armstrong/ Gyproc or Shera)Note: Contractor has to submit the drawing to the Engr-in-Charge and get the same approved before execution of GRG work. |
| 12 | S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457 mm centre to centre complete all as specified and directed. |
| 13 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 14 | S&F 4 mm thick Ecobuilding board fixed or laid/inserted to GI/ Aluminium framework with screws complete all as specified and directed. |
| 15 | S & F in repairs of 4mm th ACP (Aluminium composite panel) cladding of approved quality and colours as approved by GE, Fixing in MS frame at any ht and incl MS frame of size n.exc 0.36 Sqm ( used in rectangular tubes of size 50.8mmx25.4mmx2.9mm th or square tubes 38mmx 38mm x2.9mm th are used in frame) and filling the joints with all weather silicon sealant incl all mouldings,cutting,etc complete all as specified and directed. |
| 16 | Providing and fixing High Pressure Laminate (HPL) sheets of approved make, design, and shade, having a minimum thickness of 6- 8 mm , compact grade exterior/interior grade, conforming to EN 438 / ASTM standards, UV-resistant, anti-fade, graffiti-resistant, scratch-resistant, weatherproof, fire-retardant, termite and fungus-proof.The sheet shall be fixed on an aluminum sub-frame / wooden framework using stainless steel screws/clips as per manufacturer’s specification. All exposed edges shall be chamfered and finished properly. Installation to include provision for thermal expansion, joints, sealing, and accessories as per manufacturer\"s guidelines complete all as specified and as directed.Note:- Work includes all materials, labor, scaffolding, tools, transportation, wastage, and necessary hardware items to complete the job in all respects as per drawing and instructions of the Engineer-in-Charge. |
| 17 | Taking down of chowkhat or frame (without taking off shutter from frame) area not exc 1.50 Sqm eachincluding builder hardware fitting complete all as specified and as directed. |
| 18 | Description all as per item No 17.00 here in Before but area exc 1.50 Sqm and not exc 4.00 Sqm each complete all as specified and as directed. |
| 19 | S & F factory made UPVC colour casement (Openable) Door with frame as per reqd size made of extruded profile wilh wall thickness of 2.3mm ( +/-0.2mm). shutter profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) tobe inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) and 5.50 mm thick glazing with selected quality glass complete all as specified and as directed.(Note: The unit rate quoted by contractor includes cost ofglass and all other connected accessories.) |
| 20 | S & F factory made UPVC white colour Sliding window Three track area not exceeding 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and required accessories.(Note: The unit rate quoted by contractor includes cost of glass, wire cloth and all other connected accessories. Net Opening will be measured for payment purpose.) |
| 21 | S&F aluminium powder coated door frame with partially glazed shutters single/ double leaf divided into two glazed panels including aluminium anodised snap beading, all necessary accessories like hinges, Tower Bolt & Sliding bolt etc and rubber gasket/lining for fixing of glass as directed. The frame shall be fixed with aluminium anodised bolt by drilling in the existing wall and with thrust bolt of suitable size all as directed. The frame and shutter will be made out of the following section and fittinga) Aluminium anodised door frame 101.60 mm x 44.75 mm x 2mmfixed with aluminium thrust bolt in walls by drilling as directed. b) Aluminium anodised sides rail of shutter section 83.5mmx 44.5mm x 2mm c) Aluminium anodised bottom rail of shutter section 150mm x 44.5 mm x2mm.d) Aluminium anodised top and middle rail of shutter section 100mm x 44.5 mm x 2mm.e) Aluminium anodised tower bolt 200 mm long - 02 Nos in each leafAluminium anodised handle 250 mm long of approved Make Classic/Argent 02. No’s in each leaf. h) Glass Pane shall be 5.5 mm thick tinted glass. (j) 5 mm thick Aluminium Composite panel and lock including complete all as specified and directed |
| 22 | Supply, fabricating and fixingwindows with frame of aluminium powder coated of extruded aluminium section two track with two sliding shutters (all necessary accessories like hinges, Tower Bolt & Sliding bolt etc) with following sections (a) Framesection shall be63.50 mmx38.10 mmx2 mm thick. (b) Two track bottom rail for sliding of shutters 61.85mm x 31.75mmx2mm thick. (c) Two tracktop section shall be 61.85mmx31.75mmx2mm thick(d) for sliding shutter handle& \"H\" bottom section should be 40mmx(18mm+9)mmx1.45mm thick(e) sliding shutter to be provided with 5.5mm thick sheet glass( Modi/Saint gobain/tinted, plain, frosted(f)stainless steel wire clothes 0.36mm nominal dia of wire and average width ofaperature 1.40mmcomplete all as specified and as directed |
| 23 | S & F in Repair powder coated aluminium anodised section 40 x 44mm x14 gauge for aluminium partition wall in wall in panel 1m x1m covered with 5mm thick plain/frosted tinted glass on top half portion and 5 mm thick ACP sheet fixed in half bottom portion including V beading at Aluminium Grill edges complete all as specfied and directed. |
| 24 | S&F powder coated aluminium of various section as required for frame of door/ windown/ventilators etc with one or more rebates including jointing cleats for fixing etc complete all as specified and directed. |
| 25 | S&F powder coated aluminium window and ventilator shutters, fixed type with glass, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 75 mm long (2Nos.) suitable handle (2 No) complete all as specified |
| 26 | S&F in repair sheet glass 4.0 mm thick ordinary quality fixed with Aluminium beads in Not Exc 0.50 Sqm in each panes. |
| 27 | S&F aluminium Powder Coated grill with and including suitable aluminiumanodised frame including V - beading at all edges as requird manufactured by M/S Decogrill as per design No DG- 104 or equivatent 7.5 mm thick all as specified and as directed by Engr- in- charge. |
| 28 | S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden/ Aluminium beadding all as directed. |
| 29 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed. |
| 30 | M&L 25 mm thick PCC 1:2:4, Type B1, using 20 mm graded stone aggregate, below tiles for levelling of existing surface complete all as specified and as directed. |
| 31 | S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, over and incl 15 mm thick Screed bed in Cement Morter 1:4 for laying floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile complete. |
| 32 | S&F coloured glazed Vitrified Ceramic tile (Light shade/Double charged/Ultra charged ) 8 to 9 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floors, over and incl 15 mm thick Screed bed in Cement Morter 1:4 for laying floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile complete. |
| 33 | S&F coloured glazed Vitrified Ceramic tile (Light shade/Double charged/Ultra charged ) 8 to 9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.72 sqm, in floors, over and incl 15 mm thick Screed bed in Cement Morter 1:4 for laying floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile complete. |
| 34 | M&L glazed coloured ceramic tiles, 600x300x7mm thick, in vertical surfaces such as skirting/dado etc, set and jointed in cement slurry, laid over & including 10mm thick backing coat in cement mortar 1:4, set, jointed and pointed in white cement mixed with colour pigment to match the shade of tilecomplete all as specified and as directed. |
| 35 | S& F in repair of Modular wardrobe,cupboards, cabinets, drawers , shelfs, vanity , dressing table including shutters ( depth of 45 Cm up to 70 Cm)etc , all front side, bottom, top, two sides and partions etcmade out of 15-18 mm thickHDHMRboard and back side made out of 8 - 10 mm thick HDHMRboard (Action tesa or equivalent ) with machine pressed 0.5 to 0.8 mm thickfabric/glossy colourlaminateon all exposed front sideand other sidesdecorative laminations. All exposededges ofboardswith machine pressededge band 0.8mm from rehau Germanetc(colour of laminates , design& paterns ofpartations/ etc as approved by GE) including all accessories of fittings -Auto/soft closing hinges for shutters , C/J gola profile for handel less, telescopic channels 18\"\" / 20\"\" long , rollers for smooths sliding of drawers, etc as required complete all as specified and as directed. (Note :Overall net size front sideincluding frame will be measured for payment purpose) |
| 36 | S&Fin repair 10 mm thick toughenedfrosted glass door shutters of size area exc 1.50 Sqm but not exc 3 Sqm, including necessary floor spring hydraulically regulated, other side fixed on pivot CP fittings and fixtures, CP handles 300 mm long, CP locking arrangement, necessary cutting & holes moulding and fixed including engraving, emblem and lattering not exc 200 mm complete as per directed by Engr-in-Charge. |
| 37 | S&F in repair fixed glazed panel/window using toughened glass 12 mm thick of approved quality, edges polished, fixed with SS (stainless steel) cleats and countersunk screws, including providing and applying silicone sealant, EPDM rubber packing, and all necessary fittings/ hardwares, complete all as specified and directed by the Engineer-in-Charge. |
| 38 | S&F in Repair Stainless steel 20 mm dia curtain rod of medium weight including fixingSS brackets, curtain ring @ 7 nos/Rm and decorative end/Latto supportsetc complete all as directed. |
| 39 | Supply and fixing of wash hand basin (counter-top / under-counter / wall-mounted as specified) of approved make and design, made of white vitreous china, conforming to IS:2556, complete with vanity cabinet made of Medium Density Fibreboard(MDF), finished with high-pressure laminate/ acrylic surface as approved. The basin shall be provided with CP brass pillar tap/mixer tap, CP brass bottle trap, waste coupling, and flexible inlet and outlet connections including angle valves. Vanity to include soft-close drawers or shutters, mirror, and internal shelving as per design. All plumbing connections (inlet and outlet), fixtures, brackets, silicone sealing, cutting, jointing, fixing, and making good of walls and surfaces to be included. The item is inclusive of all materials, fittings, accessories, tools, etc., to complete the work in all respects as per directions of the Engineer-in-Charge. |
| 40 | S&F in repairs 6 mm thick bevelled edge mirror of selected quality size as per requirement,glass, mounted on wall and fixed with chromium plated brass screws and cup washers/studd complete all as specified and directed. |
| 41 | S & F in repairvertical venetian blinds of special collection self adjusting system of louvers size 100 mm wide (as approved by GE) with aluminium top rail and PVC bottom, weight attached with 100 mm strip complete with chain all as specified and directed. (Make : Vista / Hunter Douglas). |
| 42 | S&F in repair rolling shutter of approved make, fabricated from MS laths 80 mm wide, not less than 1.00 mm thick, inter-locked and machine-rolled; mounted on heavy-duty MS pipe barrel, with side guide channels, top cover, MS wire helical springs, ball bearings, and locking handle arrangement, including all accessories such as holdfasts, clamp plates, stops, and bolts, and applying one coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge. |
