Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm.(a) After proper surface preparation, Apply one coat of Primer for PU coatingas per manufacturers specification.(b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalentby brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat ofShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger PaintsNote : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicatorapproved by GE.(iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years. |
| 2 | M&L for levelling course for roof slab, Type B0, 1:2:4 (12.5 mm graded aggregate) for maintaining proper roof slope, filling the depression and finishing cement concretesurface even and smooth without using extra cement complete all as specified and directed by Engineer - in -Charge. |
| 3 | Dismantling for floor hearth or wall tiling including cement mortor bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer - in -Charge. |
| 4 | M&L non skid ceramic coloured tiles7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchand incl 15 mm thick screed bed in cm 1:6 complete all as specified and directed by Engineer - in -Charge. |
| 5 | M&L 450x300x7/ 300x600x7mm mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado Set and jointed using chemical adhesive for vertical surfaces& pointed in coloured cement to match the shade of tiles including 10mm backing coat in CM 1:4 complete all as specified and directed by Engineer - in -Charge. |
| 6 | Demolition of Concrete in ground floors and pavings n exc 15 cmthickness (below or above ground level) complete all as specified and directed by Engineer - in -Charge. |
| 7 | M & L Green Marble work 14 to 16mm thick (table moulded and mirror polished), area of each slab not less than 0.72 Sqmm in Floors, Cooking platforms, Window cills, Top of pillarstrads of steps etc including 15mm thick screed bed in cement mortar 1:6 including pointing in cement using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engr-in-Charge.Note : 1.Green marble for Window cills, top of pillars and treads of steps should be single peace upto 1.2m length of rquired width.2.White marble border for green marble flooring of required size shall be provided and it would be measured and paid as in flooring area of above item. |
| 8 | M&L for Green marble work 14 to 16 mm thick table moulded and mirror polished) in skirting on verticle surfaces as jambs of door/windows, jambs of Pillars, riser of steps etc including 10mm thick backing coat in cement mortor 1:4 including pointing in cement using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engineer-in-Charge.Note : Green marble for window jambs, pillar jambs, Riser of steps would be single piece upto 1.2m length of required width. |
| 9 | M& L for full body vitrified tiles of size 200mm/300mm/600mm x 1200mm x 8-10 mm thickset jointed and pointed in neat cement slurry in Dado/Risers of steps over 20mm of screed bed in CM 1:4 including coping at edges in PCC Type B1 (1:2:4) over 75 mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate)filling and mass concrete complete all as specified and directed by Engineer - in -Charge. |
| 10 | Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer - in -Charge. |
| 11 | M&L for brick work with sub class \"B\" bricks (old size) straight or curved on plan exc 6 m mean radius built in CM 1:6complete all as specified and directed by Engineer - in -Charge. |
| 12 | All as per Srl item No. 11 but except bricks complete all as specified and directed by Engineer - in -Charge. |
| 13 | Taking down cement plaster any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L for cement plastering 15mm thick in two layers (10mm and 5mm respectively) in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer\"s instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and smooth without using extra cement and fixing of chicken wire gauge where directed complete all as specified and as directed by Engineer-in-Charge. Note :WPC will be measured and paid separately. |
| 15 | Supply only integral liquid water proofing compound complete all as specified & as directed by Engineer-in-Charge. |
| 16 | M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. |
| 17 | M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer - in -Charge. |
| 18 | Prepration of New external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :-(a) Applying 1mm thick wall care puttyon wall surface and smoothening the surface prepatory to paint.(b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade,@ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed. |
| 19 | Prepration of New internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :-(a) Applying 1.5 mm thick wall care puttyon wall surface and smoothening the surface prepatory to paint.(b) Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. |
| 20 | Prepration of old existing external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :-(a) Applying 1 mm thick wall care puttyon wall surface and smoothening the surface prepatory to paint.(b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade,@ 10 sq.m/litre/1 coats by using roller to old existing external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 10 sq.m/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed. |
| 21 | Prepration of old existing internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :-(a) Applying 1.5 mm thick wall care puttyon wall surface and smoothening the surface prepatory to paint.(b) Applying 02 coats of interior acrylic emulsion paint (light shade) @ 20 sqm/litre/1 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. |
| 22 | Taking down steel window/ventilators chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each complete all as specified and directed by Engineer in Charge |
| 23 | Providing and fixing factory made uPVC white colour casement (Openable) window of total four panels out of which 2 glass and 2 ss mesh panel made ofextruded ISI mark profiles which should be lead free andcadamium free manufactured by and IS 9001:2015 company having manufacturing facilities in Inda andhaving licence from Bureau of Indian Standard with wall thickness of 2.3 mm (+ -0.2mm). window profile with hollow section with multi chamber, frame (67 mm x62 mm), sash (67 mm x 78 mm), t Profile (One verticle length in between two shutters) (67 mm x 78.4mm), glazing bead 42 mm x 25.8 mm) will be mitered cut andfusion welded at all corners, including drilling of holesfor fixing hard ware and drainage of water etc, making bead (42 mm x 25.8 mm) will be mitered cut an and +-0.2 mm thick, galvanised steel 1.5 mm thick, Forframe (29 mm x 25mm) , xash (38 mmx 28mm). T Profile (38 mm x 25.5 mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners. HArdware: (casement handle made of zinc alloywed( white powdercoated), but hinges of zincalloyed (white powder coated), transmission gear made of mild steel with multi pointlocking system) and 5 mm thick clear thoughened glazingwith selectedquality glass . Note: the unit rate quoted by the contractor excludes cost of glass and includes all othere connectedaccessories. |
| 24 | Providing and fixing factory made uPVC white colour casement (Openable) window of total two panels out of which 1 glass and 1 SS mesh panel made ofextruded ISI mark profiles with wall thickness of 2.2 mm (-0.2 mm). Window profile with hollow section with multi chamber, frame of (127 mm x 62 mm), sash (67 mm x 78 mm)., t Profile (one vertical length in between two shutters)(127 mm x 72 mm) , Glazing bead (42 mm x 25.8 mm) will be mitered cut andfusioon welded at all corners , including drillingof holes for fixing hardware and drainage of wateretc making arrangementfor fixing of hardware. EPDM gasket 1.2 +-0.2 mm thick, galvanised steel 1.5mm thick, forframe one chambere of (51 mm x 25 mm) and anotherof (34 mm x 25 mm) , sash (38 mm x 28mm). T Profile for one chamber(51 mm x25 mm) and another of (34 mm x 25 mm) to be inserted in required profile, frame will be fixed to thewall with 8 mm x 100 mm long fasteners. HArdware : (Casmenthandle made of zinc alloyed (white powder coated), Butt hingesof zinc alloyed (White powder coated), transmisson gear made of mild steel with multi point locking system) and 5 mm thick clear toughened glazing with selected qualityglass . Note: the unit rate quoted by the contractor excludes cost of glass and includes all othere connectedaccessories. |
| 25 | S & F for 5.5mm thick toughened glass (tinted),selected quality and glazing with necessory arrangement in square exc 0.5 sq. m in each pane complete all as specified and directed by Engineer - in -Charge. |
| 26 | Easing or Resecuring of existing steel windows shutter not exc 1.0 sqm by straightening stiles/ rails and welding hinges and joints includingtaking outsteel window shutters from the frame and refixing after making serviceable/ functionalall as directed complete all as specified and directed by Engineer - in -Charge. |
| 27 | S&F framed brackets of angles or tee with web and flange cut to shape, drilled and counter shunk for screw, including bending and welding angles asnecessary gusset plates riveting rails, braces,running rails and guides and hanging, handles, peg stay for steel windows/ ventilators ; also fastening and fixing complete conforming to Fe-290(Grade-165)all as specified and directed by Engineer-in-charge. |
| 28 | Cutting holes in brick (n.exc half brick)walls in cement mortar forinserting holdfasts andmaking gooddismantled portion incement mortar 1:3 or cement concrete 1:2:4Type B-1 as required complete all as specified and directed by Engineer - in -Charge. |
| 29 | Taking down wooden/FRP/PVC or of any materialchowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqmeach complete all as specified and directed by Engineer in Charge |
| 30 | S& F Factory made Laminated single extruded WPC (Wood Polymer Composite) 100 % solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 75 x 50 mm(moulded) single rebated, made from wood polymer composite(single extruded process) material comprisingof virgin PVC polymer ofK value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 780 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be not paid for separately) Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 31 | S& F Factory made Laminated single extruded WPC (Wood Polymer Composite) 100% solid plain flush door shutter of 24 mm thick size comprising of virgin polymer of K value 57-60 (Suspension Grade), calciumcarbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: 125 mm long stainless steel butt hinges (03 nos), 150 mm long aluminium handles (02 Nos) and 150 mm longaluminium tower bolts shall not be paid separately) |
| 32 | Taking down wooden chowkats or frames (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and directed by Engineer in Charge |
| 33 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 65x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note : Rates of Taking down are included. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 34 | S&F Factory made 30 mm thick 100 % solid WPC (Wood Polymer Composite) Laminated Flush Door size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note:Including 125 mm SS hinges with stainless steel screws (03 Nos ), 200 mm longStainless steel tower bolt (02 Nos) and 300mm long Stainless steel sliding bolt (01/02 Nos) & Stainless steel handles (02 Nos) |
| 35 | S&F Factory 30 mm thick 100 % solidWPC (Wood Polymer Composite) Laminated Wiremesh shutter of size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note:Including 125 mm SS hinges with stainless steel screws (03 Nos ), 200 mm longStainless steel tower bolt (02 Nos) and 300mm long Stainless steel sliding bolt (01/02 Nos) & Stainless steel handles (02 Nos) |
| 36 | Taking down shutters of any description and typeexc 1 Sqm but n exc 2 sqm each and refixing in same opening after resecuring easing duly completed repair workitems in all respects etc.complete all as specified and directed by Engineer - in -Charge. (Note: 125 mm long stainless steel butt hinges (03 nos), 150 mm long aluminium handles (02 Nos) and 150 mm longaluminium tower bolts to be provided and shall not be paid separately) complete all as specified and directed by Engineer - in -Charge. |
| 37 | Taking down shutters of any material and descriptionand type n exc 1 Sqmeach and refixing in same opening after resecuring easing duly completed repair work in all respects etc.complete all as specified and directed by Engineer - in -Charge. (Note: 125 mm long stainless steel butt hinges (03 nos), 150 mm long aluminium handles (02 Nos) and 150 mm longaluminium tower bolts to be provided and shall not be paid separately) complete all as specified and directed by Engineer - in -Charge. |
| 38 | S & F for floor door stopper of aluminium alloy body and tongue, Overall length of cover plate 140mm anodised, with hard drawn steel spring, complete all as specified and directed by Engineer - in - Charge. |
| 39 | M&L one coat of synthetic enamel paint on old painted surfaces of wood and wood based materials over 10 cm width or girth including preparation complete all as specified and directed by Engineer - in -Charge. |
| 40 | M&L one coat of synthetic enamel paint on old painted surfaces of steel and iron work over 10 cm width or girth including preparation complete all as specified and directed by Engineer - in -Charge. |
| 41 | M&L two coats of synthetic enamel paint over a coat of red oxide primer on new surfaces of steeland steel based materials over 10 cm width or girth including preparation of surfaces complete all as specified and directed by Engineer - in -Charge. |
| 42 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads complete all as specified and directed by Engineer - in -Charge. |
| 43 | S&F 4mm sheet glass ordinary quality and glazing with oil putty in squaren. exc 0.5 sqm in each plane complete all as specified and directed by Engineer - in -Charge. |
| 44 | S&F drapery curtain rod 25mm dia, fancy type, fabricated out of mild steel sheet not less than 20 gauge, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated power coated natural color complete all as specified & directed by Engr-in-Charge. Note :Length of Drapery road inclusive of finials for payment purpose. |
| 45 | Taking down eaves gutter or rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks etc. complete all as specified and directed by Engineer - in -Charge. |
| 46 | S&F 110mm bore uPVC (SWR) pipes single socketed in any length with rubber ring joints, jointed with solvent fixed to wall or laid in trenches with matching uPVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends/Tee/elbow/ branch piece complete all as specified & directed by Engr-in-Charge. |
| 47 | S&F 110 mm bore uPVC (SWR) bends any radius complete all as specified & directed by Engr-in-Charge. |
| 48 | S&F 110mm bore uPVC (SWR) branch piece, single (single Y) equal or unequalcomplete all as specified & directed by Engr-in-Charge. |
| 49 | S&F 110mm bore uPVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified & directed by Engr-in-Charge. |
| 50 | S&F 110mm bore uPVCjunction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge. |
| 51 | S&F 110mm bore uPVC (SWR) junction double, (double T), equal or unequal complete all as specified & directed by Engr-in-Charge. |
| 52 | S&F 110mm bore uPVC (SWR) couplers complete all as specified & directed by Engr-in-Charge. |
| 53 | S&F 110mm bore uPVC (SWR) reducers complete all as specified & directed by Engr-in-Charge. |
| 54 | S&F 110mm bore uPVC (SWR) vent cowl complete all as specified & directed by Engr-in-Charge. |
| 55 | S&F 75 mm bore uPVC (SWR) pipes single socketed in any length with rubber ring joints, jointed with solvent fixed to wall or laid in trenches with matching uPVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends complete all as specified & directed by Engr-in-Charge. |
| 56 | S&F 75 mm bore uPVC (SWR) branch piece, single (single Y) equal or unequalcomplete all as specified & directed by Engr-in-Charge. |
| 57 | S&F75 mm bore uPVC (SWR)junction single, (Single T) equal or unequal complete all as specified & directed by Engr-in-Charge. |
| 58 | S&F 75 mm bore uPVC (SWR)junction double, (double T), equal or unequal complete all as specified & directed by Engr-in-Charge. |
| 59 | S&F 75 mm bore uPVC (SWR)couplers complete all as specified & directed by Engr-in-Charge. |
| 60 | S&F 75 mm bore uPVC (SWR) reducers complete all as specified & directed by Engr-in-Charge. |
| 61 | S&F 75 mm bore uPVC (SWR) vent cowl complete all as specified & directed by Engr-in-Charge. |
| 62 | Taking up or down GI steel water tubing 15mm bore and connections including fittings from floor/walls/ceiling complete all as specified and directed by Engineer - in -Charge. |
| 63 | Taking up or down GI Steel water tubing 20mm bore and connections including fittings from floor/walls/centrings complete all as specified and directed by Engineer - in -Charge. |
| 64 | Taking down or up steel water tubing 25 mm dia bore of pipeandremoval to store complete all as specified and directed by Engineer - in -Charge. |
| 65 | Supplying and laying of CPVC pipes of dia 20 mm SDR 11 & Plain CPVC SDR 11 inlcuding allfittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge. |
| 66 | Supplying and laying of CPVC pipes of dia 25 mm SDR 11 & Plain CPVC SDR 11 inlcuding allfittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge. |
| 67 | Supplying and laying of CPVC pipes of dia 32 mm SDR 11 & Plain CPVC SDR 11 inlcuding allfittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge. |
| 68 | Supplying and laying of CPVC pipes of dia 40 mm SDR 11 & Plain CPVC SDR 11 inlcuding allfittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge. |
| 69 | Dismantling water tanks any type exc. 500 ltr but nexc 1000 ltr complete all as specified and directed by Engineer - in -Charge. |
| 70 | S&F rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I, 1000 Litres capacity complete all as specified and directed by Engineer - in -Charge. |
| 71 | S&F 20mm ball valves high pressure of PTMT with epoxy coatedAluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed by Engineer - in -Charge. |
| 72 | S&F in repair, vitreous china squatting pan \"ORISSA\" pattern white, of size 580x440mmwith integral foot rest, CI \"P\" trap etccomplete all as specified and directed by Engineer - in -Charge. |
| 73 | Supply and fixing PVC low level dual type flushing cistern 10 liter capacity, valveless, syphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density, PVC connection 15 mm dia and 450mm long & bracket etc complete all as specified and directed by Engineer - in -Charge. |
| 74 | S&F wall hung WC with UF Seat Cover ,Hinges, Accessories SetSize 640 x 360 x 765 mm white complete, includingconcealed body flushing cisternwith hinging arrangement, complete all as specified and directed by Engineer - in -Charge. |
| 75 | S&F health faucet to EWC, CP brass with minimum 1000mm long CP flexible pipe, connection etc., complete all as complete all as specified and directed by Engineer-in-Charge. |
| 76 | S&F in repair for vitreous China urinals,full stall urinal (back or corner wall type), complete includingproviding and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. inclusive of fixing supply pipe to flushing cistern, trap and waste pipe) and including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms). complete all as specified and directed by Engineer - in -Charge. |
| 77 | Supply and fix in repairs vitreous china wash hand basin counter shank with green/black granite slab to be cut and polished at site as per requirement, brackets, 32mm bore brass chromium plated waste coupling & 32mm bore low density polythelene (LDPE) flush pipe of pressure 6Kgf/Sqcm (1.00M long,)including 15mm bore 450/600mm length PVC connection with PTMT nuts and fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. Note : Rates of Granite are included in this item of BOQ |
| 78 | S&F in repairsoap dish, vitreous china white complete all as specified and directed by Engineer - in -Charge. |
| 79 | S&F CP shower rose 125mm size and 15mm dia, fixed in repairs complete all as specified and directed by Engineer - in -Charge. |
| 80 | S&F CP towel rail 600mm long fixed with CP brass screws complete all as specified and directed by Engineer - in -Charge. |
| 81 | S&F 600x450 mm bevelled edge mirror of selected qualite glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium platedbrass screws and cup washers complete all as specified and directed by Engineer - in -Charge. |
| 82 | S&F 15mm bore PVC connections, with PTMT nuts, of length 450/600mm complete all as specified and directed by Engineer - in -Charge. |
| 83 | Supply and fix in repairs chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by Engineer - in -Charge. |
| 84 | Supply and fix in repairs chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by Engineer - in -Charge. |
| 85 | S&F in repair 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer - in -Charge. |
| 86 | S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer - in -Charge. |
| 87 | S&Fin repairs 15mm bib taps cast copper alloy, chromium platedfancy type with crutch or butterfly handle screwed down screwed for Iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer - in -Charge. |
| 88 | S&F Single lever Basin Mixer without Popup waste with 450 long Braided Hoseswith long screwed for iron pipe of 15 mm dia, complete all as specified and directed by Engineer - in - Charge. |
| 89 | S&F Grating doom 100mm dia of CP (Minimum weight 25gms) complete all as specified and directed by Engineer - in -Charge. |
| 90 | M & L for 75mm thick cement concrete type C-2, 1:3:6 using 20mm graged aggregate as in plinth protection complete all as specified and directed by Engineer - in -Charge. |
| 91 | M & L for 40mm thick cement concrete type B-1, 1:2:4 using 20mm graged aggregate as in flooring , finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer - in -Charge. |
| 92 | M&L for PCC (1:5:10) type E-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed by Engineer-in-Charge. |
| 93 | M&L for Providing RCC precast cement concrete Type B0 1:2:4 (12.5mm gragded aggregate)40 mm thick Jallies(measured solid includingallmouldings and frame) complete all as specified and directed by Engineer-in-Charge. |
| 94 | S&F 0.56 mm thickPlain, Aluminium sheeting, Alloy 31000 H4 for crumple/ expansion joints, ridges, hips, valley gutter, drip,and straight flashing (length and girth as fixed)fixed with self tapping screws complete all as specified and directedbyEndineer -in -Charge. |
| 95 | M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge:- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c)Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d)Apply first coat of two component modified polymer coating on the horizontal and verticle surface(e)Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 over the coating as per requirment (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete all as specified and directed by Engineer-in-Charge. Make:- Dr. Fixit/Fosroc/STP/SIKA Note: (i)PCC filling in sunken portion will be measured seperately. (ii) Complete treatment/work to be executed by the approved applicator.Warranty to be given by the applicator firm of 5 years in writing. |
| 96 | S&F 18mm thick high Density High Moisture Resistant (HDHMR) exterior Grade Board with both side white balancing (BSB) with density of 850 Kg/cu.m complete all as specified and directed. Make : Action Tesa/ Greenpanel/Century Note : (i) Board on back side wall will be fixed with minimum 5mm PVC spacers. The payment for the same deemed to be included in the quoted unit rates. (ii)Rates of following items are included :(i) Auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree.(ii) Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs.(iii) Tower bolts 250mm long of stainless steel 304 finished/of outer plate metalmatt finished. (iv) D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished200mm long matt finished.(v) Butt hinges of size 75mm of stainless steel 202 Grade finished/of outer plate metal.(vi) Piano/continuous hinge of size 19 mm stainless steel complete all as specified. |
| 97 | Demolition of Cement concrete(reinforeced) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer - in -Charge. |
| 98 | M&L Reinforced Cement concrete Type B1 1:2:4 (nominal mix) 20mm graded stone aggregate in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge |
| 99 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engineer-in-Charge |
| 100 | M&L providingreinfoced cement concrete (nominal mix) in cement concrete 1:1.5:3 Type B1(20mm graded aggregate)as chajjas, lintels, water tank staging slab and likeetcand similar workcomplete all as specified and directed by Engineer-in-Charge.Note : The rate quoted shall be deemed to include use and waste of necessary form work |
| 101 | M & L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bendingspirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clipsNote : Additional Reinforcement: Check the diameter of the existing rebars and if the diameter is less than 30% of the original diameter, provide additional reinforcement. Cut 12mm dia bars as main reinforcement to the required length with proper development length. Tie them to the prefixed shear connectors so that the additional rebar acts monolithically with the existing ones and core concrete. |
| 102 | Material and labour for Chipping of unsound/weak concrete materials offrom Column/beams/ slabs/ chajjas with standard power driven percussion type or pneumatic chiesel of standard make includingtaperingall edges, making square shoulders of cavities etcupto any height including necessary scaffolding and safety measures complete all as specified and as directed by the Engr-in-Charge. |
| 103 | Exposing the corroded reinforcement upto and including 16mm dia of bar completely along its full circumference, cleaned to remove all loose scale and corrosion deposit, applying rust removing chemical followed by removing the rust by emery paper and cleaning the area thoroughly by water and allow it to dry as permanufacture\"s instruction upto any height including necessary scaffolding and safety measures complete all as specified and as directed by the Engr-in-Charge.Make :Fosroc / SIKA / Dr. Fixit / Bostik / Choksey |
| 104 | Supply and application of Epoxy Zinc rich primer on the prepared Reinforced surface by brush, the primer shall have a minimum specific gravity 1.75, minimum wet film thickness/coat 100 microns & dry film thickness/coat 40 microns. Minimum adhesive bond strength with steel is 1.5 N/mm2 upto any height including necessary scaffolding and safety measures complete all as specified and as directed by the Engr-in-Charge. Make :Fosroc / SIKA / Dr. Fixit / Bostik / Choksey |
| 105 | M & L for Shear Connectors by drilling 12mm dia holes up to a depth of 75mm maximum and fixing 8mm dia L shaped anchor rods as shear connectors at every 300mm c/c on the surfaces of the columns/beams or any other structural member as the case may be. Clean the same using air or blower and make sure that there are no fine particles present in the hole and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound. At this stage push the shear connector gently in to the hole and finish the excess resin which comes out of the hole and allow the shear connectors not to be disturbed for Minimum 20 minutes. Make: M/s Sika India Pvt Ltd/ Fosroc/Bostik/Choksey/Dr Fixit etcNote : Complete treatment/work to be executed by the approved applicator. |
| 106 | M & L for applying bond coat on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified mortar or micro concrete with two coats of Sika-Latex Super SBR or equivalent as per manufacturer specifications. Laying of reinstatement polymer mortar or micro concrete shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete complete all as specified and directed by Engineer - in -Charge.Make: Equivalent of M/s Sika India Pvt Ltd/ Fosroc/Bostik/Choksey/Dr Fixit etc.Note : Complete treatment/work to be executed by the approved applicator. (Reinforcement shall be measured & paid separately) |
| 107 | “M&L for applying to the damaged concrete portion of slab/ columns/ beams/ chajjas/ parapet /roof projection/ balcony / staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious patch Repair Mortar Renderoc SP40 (having the technical parameters mentioned in material specifications) capable of applying an average up to 20-45mm thick in single layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness complete all as specified and directed by Engineer - in -Charge.Make: Equivalent of M/s Sika India Pvt Ltd/ Fosroc/ Bostik/Choksey etc. Note : Complete treatment/work to be executed by the approved applicator. |
| 108 | Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in -Charge. |
| 109 | Taking down existing tube light/ mirror light/ building light etc of any type/make/capacity from building/ rooms including testing serviceability.Refixing the same if found serviceablecomplete all as specified and directed by Engineer - in -Charge. |
| 110 | Fixing only LED lights fitting 1x20/25W, 220V, LED tube light/securirty light/bulk head/mirror light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer - in -Charge. |
| 111 | M & Lfor concealed conduit Flame proof point wiring complete for light/ fan on independent /combine boardwith cable 2.5 sqmm (Nominal area) FRLSHPVC insulated multistranded unsheathed copper conductor,drawn in and including In stove enamelled steel Concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , aftercutting in wall chasing for conduits and sinking\"s for modular metal flush boxes suitable lengthand Min 1.6 mmthickness, Min 51 mm depthfor mounting, switches, sockets,fan regulatorwith modular cover plate with frame and making the gooddisturbed surfaces of wallin CM 1:3 with white wash or existing colour including provision ofcontinuousearth continuity conductoralong with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddirecedby the Engineer in charge. |
| 112 | M & Lfor concealed conduit point wiring complete for light/ fan on independent /combine boardwith cable 2.5 sqmm (Nominal area) FRLSHPVC insulated multistranded unsheathed copper conductor,drawn in and includingPVC Concealed conduitpipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , aftercutting in wall chasing for conduits and sinking\"s for modular metal flush boxes suitable lengthand Min 1.6 mmthickness, Min 51 mm depthfor mounting, switches, sockets,fan regulatorwith modular cover plate with frame and making the gooddisturbed surfaces of wallin CM 1:3 with white wash or existing colour including provision ofcontinuousearth continuity conductoralong with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switchand connected to commonearth dolly, complete all as specified anddirecedby the Engineer in charge. |
| 113 | All as per Srl item No -112 here in before but for one switch socket combination5/6 amp on independent board complete all as specified and directed by Engineer - in -Charge. |
| 114 | All as per Srl item No -112 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in -Charge. |
| 115 | All as per Srl item No. 112 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in -Charge. |
| 116 | All as per Srl item No. 112 here in before but for Industrial Socket on independent board with copper conductor 4 Sqmm complete all as specified and directed by Engineer - in -Charge. |
| 117 | All as Srl item No. 112 here in before but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer - in -Charge. |
| 118 | S & F in switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed by Engineer - in -Charge. |
| 119 | S & F in repair modular switch5/6 Amps single pole one way,one module complete all as specified and directed by Engineer - in -Charge. |
| 120 | S & F in repairModular switch 1 way 16A,with box complete all as specified and directed by Engineer - in -Charge. |
| 121 | S & F in repairmodular Socket,16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in -Charge. |
| 122 | S & Fin repair modular Socket,6A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in -Charge. |
| 123 | S & F modular switch5/6 Amps single pole two ways complete all as specified and directed by Engineer – in -Charge. |
| 124 | Supply and fix in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amp complteall as specified and directed by Engineer - in -Charge. |
| 125 | S & F modular stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in -Charge |
| 126 | S & F ceiling rose surface bakelitethree terminals complete all as specified and directed by Engineer - in -Charge. |
| 127 | S & F in replacement of existing light fitting withLED batten with aliminium housing andintegrated electronic driver,20 watt having input voltage AC90-300V, 50 Hz , 6500K, and all other accessories including connection with flexiblecable copper conductortwin coreof size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in -Charge. |
| 128 | Supply and fixing LED light fitting 1x16/20 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size. |
| 129 | Supply and Fixing of Flameproof cum Waterproof LED Bulk Head light fitting of 15W, IP66 protection of Cast Aluminum alloy material and Heat and Impact resistance toughen \"A\" clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor cable with suitable size. |
| 130 | S&Fin replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in -Charge |
| 131 | S & Fin replacement Water tight bulk head fitting,comprision of connector galvanised cast iron back plate,weather proof enamelled gallery ,glass well,and including 10 watt LED lamp all as specified and directed by Engineer - in -Charge |
| 132 | S & F in replacement compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified. |
| 133 | S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in -Charge |
| 134 | S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in -Charge. |
| 135 | S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steeldia 25mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cableas earthcontinuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and coversincluding necessary connections, PVCflexible pipes are used in pannel board while connecting the cablecomplete all as specified and directed by Engineer - in -Charge. |
| 136 | S&F in replacement sub main two single core PVC copper conductor unsheathed wiremulti stranded 4 sqmm FRLSH including cutting chasing and grouting PVC pipe including Tee, Elbow, Bend etc andincluding 4.0 sqmm copper conductor single core wire connected by common earth all as specified. Including 20 mm dia concealed PVC conduit, medium grade, ISI marked complete all as specified and directed by Engineer-in-Charge.Note :- Two lengths of 4.0 sqmm cable and one length of 4.0 sqmm earth cable along with PVC conduit will be measured as one running length |
| 137 | S&Fin replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 VoltISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 250A,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge. |
| 138 | S&F in repairs MCCB 4 pole 63 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge. |
| 139 | S & F Flame proof sheet metal enclosure for double door DB made out of Heay CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 4 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in -Charge. |
| 140 | S & F sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in -Charge. |
| 141 | S & F MCB ‘C’ series type suitable for 240 volts, AC supply 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in -Charge. |
| 142 | S & Fin replacementMCB ‘B’ series type suitable for 240 volts,10 KA,AC supply6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in -Charge. (Make - Havells / Legrand / Indo Asian) |
| 143 | M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mmthick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GIand protection by provisionof GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge |
| 144 | Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer - in -Charge. |
| 145 | S&F exhaust fan made of Metal Body of 300 mmsweep ,240 volt, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVCsheathed copper conductorflexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc. |
| 146 | AIR COOLED HEAT PUMP FOR GENERATING HOT WATER WITH INBUILT HOT WATER TANKSupply, installing, commissioning & Testing of Air cooled integrated type Heat Pump delivering actual capacity as per the following parameters. Heat pump shall be rated at Nominal Input Power not more than 0.63 KW with Output Heating capacity not less than 2.6 KW, Electrical Backup not less than 2 KW having Inbuilt Tank capacity - 450 litres having glass lining. Water Temp in efficiency mode using compressor should be at least65 degree C. Heat pump should have all the safety protections like high/low voltage , high temperature, refrigerant leak, compressor overheating protection with operational noise level not more than 60 dbA. Heat pump should have a user friendly control panel to set the desired temperature showcasing the actual temp also with flexibility of installing the same 15-30m away from the heat pumps also with following, complete all as specified and as directed. RETURN CIRCULATION PUMPProviding, fixing, commissioning and testingof pumphaving SS304impellers comprising of 1 no. electrical driven pump of 1000 LPH to a head to 30 meter with all accessories coupled to motor suitable for operations, 1/3 phase to be supplied with timer based control panel for automatic operation basis the set time tablePRESSURE PUMP ON WORKING STANDBY OPTIONProviding, fixing, commissioning, testing of package SS304horizontal Hydro pneumatic system, comprising of 1 no. electrical driven pump of 5000 LPH to a head to 30 meter with all accessories coupled to motor suitable for operation on 400 / 440 volts, 1/3 phase 2900 RPM. including with motor with 60 Litres of pressure vesselhaving 1 working and 1 standby option with sequential control panel – 02 Nos (1W + 1S) |
| 147 | Excavation in trenches not exceeding 1.5 mtr wide and not ecxceedinf 1.5 mtr depth for laying of cablescomplete all as specified and directed by Engineer - in -Charge. |
| 148 | Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engineer - in -Charge. |
| 149 | Removal of Excavated material n exceeding 50 mtr and depositing where directed complete all as specified and directed by Engineer - in -Charge. |
| 150 | Supply, Laying DWC pipe size 77 mm OD/ 63 mm ID by Excavated Methed complete all as specified and directed by Engineer - in -Charge. |
| 151 | M & L forboring hole under road,pavement , hard standing by trenchesless for laying DWC pipe suitable for outer dia of cable passing without damaging Road / Plinth /Floor complete all as specified and directed by Engineer - in -Charge. |
| 152 | Supply and lay jointing and testing and commissioning in replacement of 35 Sqmmx 3.5core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
