Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Taking downcement or cement lime plaster of any description on brick, block or stone walls etc (at any height) including racking out joints, hacking for key scrubbing down with water etc complete & removing debris outside MD land as directed. |
| 2 | M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement etc complete all as specified and as directed. |
| 3 | M&L for 15mm thick plaster in CM 1:4 (using water proofing liquid as per manufacturers instructions) on other than fair faces of brick work masonary surface or concrete surface finished even and fair without using extra cement complete all as specified and directed. |
| 4 | M&L for rendering 5mm thick in cement mortar (1:3) on concrete surfaces as in ceiling finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 5 | Supply only liquid water proofing compound complete, ISI mark all as specified and as directed. |
| 6 | Removing the loose spalled concrete portions from Ceiling, wall, beams, Chajja surface cleaning thoroughly by making it free of dirt, rust etc. and applying rust removing solution to exposed corroded reinforcement, applying a coat of DR. FIXIT Epoxy Zinc Primer or equivalent to the reinforcement bars, and fixing of wire mesh having 0.90 mm dia and 12 mm aperture with nails, applying 1 coat of bonding agent (DR. FIXIT Pidicrete MPB or equivalent) mixed with cement (ratio 1:1) andfinally rendering the surface avg 25 mm thick withDR. FIXIT Polymer Mortar PX or equivalent complete all as specified and as directed.Note: 1. Location shall be verified and approved by the Engineer-in-charge before carrying out the treatment.2. Make of Chemical shall be approved by the GE before start of application. |
| 7 | M&L for brickwork with fly ash bricks, straight or curved on plan, exc 6 m mean redius,built in cement mortar 1:6 with and including demolition of existing brick work built in cement or cement lime mortarof any description complete all as specified and as directed. |
| 8 | M&L for preparation of new plastered internal surfaces of wall and applying two coat ofacrylic distemper of required shade and colour complete including one coat of primeras per manufacturer\"s specifications in any colour complete all as specified and directed. |
| 9 | M&L for newly plastered wall surfaces, preparation of surface and applying applying two coats of 100% premium exterior acrylic emulsion paint (weather coat) alkali & fungal resistance, dirt resistance of required shade over and including priming coat of exterior primer complete all as specified and as directed. |
| 10 | M&L for newly plastered wall surfaces, preparation of surface and applying applying two coats of cement base paint of required shade over and including priming coat of alkali resistant primer complete all as specified and as directed. |
| 11 | M&L for preparation of new plastered surfaces of ceiling and applying three coat ofwhite wash complete all as specified and directed. |
| 12 | M&L for preparation of newly plastered surfaces and applying three coats of white wash on wall complete all as specified and directed. |
| 13 | M&L for applying 1.5 mmthick of Birla/ JK wall care putty in new or old decorated surfaces of walls and sanding the surfaces till smooth finish is obtained for receiving finishes complete all as specified and as directed |
| 14 | M&L for Preparation of old decorated surfaces of walls and applying two coats of white wash complete all as specified . |
| 15 | M&L for Preparation of old decorated surfaces of ceiling and applying two coats of white wash complete all as specified . |
| 16 | M&L for preparing of old surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying two coats of acrylic distemper in any colour complete all as specified and as directed. |
| 17 | M&L for complete removal of existing treatment on old decorated plastered suface of externalwalls including filling cracks using acrylic wall crack filler & applying two coats ofExterior Acrylic Emulsion paint, alkali & fungal resistance, dirt resistance of required shade over one coat of primer as requiredcomplete all as specified & directed by Engr in charge. |
| 18 | M&L for preparation of old painted wood or wooden based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint on oldcomplete all as specified and directed. |
| 19 | M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 20 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removingrubbish off the premises all as specified and directed. |
| 21 | M&L for coloured non-skid ceramic tiles, 7 to 8 mm thick (square or rectangular), area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over & including 15 mm thick screed bed in cement mortar 1:6complete all as specified and as directed.Note :- Colour and shade shall be approved by Engr-in-Charge. |
| 22 | M & L for Non-skid coloured Ceramic tiles mat finish 7 to 8 mm thick (square/Rectangular)area of each tile exceeding 0.18 sqmbut not exc 0.38 sqm (600x600mm)in floors etc set and jointed in neat cement slurryand pointed inwhite cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed.Note :- Colour and shade shall be approved by Engr-in-Charge. |
| 23 | Ditto all as per item No 22.00 above but as in skirting set and jointed in neat cement and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 24 | M&L for glazed coloured ceramic tiles in vertical surfaces as dado of size 450x300x6-7mm, thick set and jointed in neat cementand pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on other than fair faces of brick work etc complete all as specified & as directed.Note: Color, size and shade shall be as approved by Engineer-in-charge |
| 25 | Dismantling kota, granite, cudappa stone slabsand interlocking tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortor complete all as specified and as directed. |
| 26 | M&L for machine cut Kota stone flooring 18 to 22 mm thick(minimum size of kota stone slab 18\"x22\") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed. |
| 27 | All as per item No. 26.00 here-in-beforebut 15-18 mm thick as in risers to steps andskirtinglaid over and including backing coat of 10mm thick cement mortar 1:3all as specified and as directed.Note : Riser provided to steps shall be in one piece. |
| 28 | M&L for machine cut Kota stone slabs 18 to 22 mm thickas in treads of steps of stair case in single piece with 2 nos V groove cutting laid over and including 10 mm thick cement screed bed in CM 1:3and jointed with grey cement slurry mixed with pigment to match the shade of the slab including, rounding and moulding edges, rubbing and mirror polishing complete all as specified and as directed. |
| 29 | M&L for machine cut cudappah stone slab 20-25mm thick for cooking platform, wash basin, sink etc including cutting chases in wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed. |
| 30 | M&L 18 to 20mm thick pre-polished granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/platform, gate pillars, cills etc or on vertical surfaces including vertical projection, urinal partition, including full round moulding the edge, laid overand including screed bed 20mm thick in cement mortar 1:4jointing, pointingin white cement 1:2 using marble dust with admixture or pigment to match the shade of granite and rubbing, polishing to achieve mirror finish complete all as specified and as directed.Note: Colour and shade shall be asapproved by GE. |
| 31 | Demolition of cement concrete (unreinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 32 | M&L for 75mm thick plain cement concrete 1:4:8type D-2, using 40 mm graded stone aggregate as in sub base of floors and pavingsall as specified and as directed. |
| 33 | M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smoothwithout using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic jointfilling at every 3m length and at corners complete all as specified and as directed. |
| 34 | M&L for PCC 25 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate as in levelling course infloors, roofcomplete all as specified & directed. |
| 35 | M&L for 60mm thick, factory made, chamfered edge, cement concrete interlocking paver blocks (glossy/ rubber matt finish) of M-35 grade with approved colour, design & pattern of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks asrequired size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.Note: Size, shape, pattern and shade shall be asapproved by Engineer-in-Charge. |
| 36 | M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cementconcrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required excavation,returning filling and removal of soil complete all as specified and as directed. |
| 37 | Taking down chowkats or frames with shutters (without taking off shutters from the frames), area exc 1.50 sqm but n exc 4 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and asdirected. |
| 38 | Taking down chowkats or frames with shutters (without taking off shutters from the frames), area n.exc 1.50 sqm each and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and asdirected. |
| 39 | Taking down shutters of any description area exc 1 sqm & n.exc 2 sqm each leaf and complete all as specified & as directed. |
| 40 | S&F pressed steel doors frames of size 125 mm x60 mm x 1.25mm thick with one or more rebates including necessary fixing lugs, hold fastslock strike plate, etc. including filling with PCC 1:3:6 type C0 complete as specified and as directed.Note: MS butt hinges shall be measured and paid separately under respective item. |
| 41 | S&F pressed steel doors frames of size 105 mm x60 mm x 1.25mm thickwith one or more rebates including necessary fixing lugs, hold fasts, lock strike plate, etc. including filling with PCC 1:3:6 type C0 complete as specified and as directed.Note: MS butt hinges shall be measured and paid separately under respective item. |
| 42 | M & L cement concrete type B-0 1:2:4 (12.5 mm graded agg ) as in bed block ,hold fast, coping and similar work etc complete all as specified and as directed. |
| 43 | S&F 35 mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressuretreated all as specified and as directed. |
| 44 | S&F 35mm thick IInd class hard wood glazed skelton shutters,factory made,open rebated and prepared to recive glass,guage etc,(with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of sutters as specified in SSR part - I section - 8, clause 8.20 (a). S&F to chowkhat complete all as specified and as directed. |
| 45 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specified and as directed.Note: (i) Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door/window frames. Variation in profile dimensions on plus side shall be acceptable without any extra cost to the department |
| 46 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges shall be paid separately under respective item. |
| 47 | S&F powder coated anodized aluminium frames for door, window, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed.Note:- Colour shall be as approved by GE/Engineer-in-Charge. |
| 48 | S&F in repair powder coated anodised aluminium ventilator having aluminium section weighing not less than 0.55 kg/m, including aluminium louvers, frosted 3mm thick glass, SS wire mesh, including arrangement for fixing of exhaust fan and necessary joining cleats,glazing clips,screws etc complete all as specified and as directed.Note :Shade shall be as approved by Engineer-in-Charge. |
| 49 | S & F powder coated aluminum windows, three track, made out of aluminium sectionsincluding all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a)Window frame:(i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m)(ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m)(b)Shutter: (i)Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)Note :Shade shall be as approved by Engineer-in-Charge. |
| 50 | S&Fin position 4.8 to 5mm thick clear float / frosted glass of ordinary quality and glazing with glazing clips including necessary rubber packing to aluminium frame n.exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 51 | S&Fin position 4.8 to 5mm thick clear float / frosted glass of ordinary quality and glazing with glazing clips including necessary rubber packing to aluminium frame exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 52 | S&F mild steel framed work such as grill, gratings, guard barsetc with end of bars shouldered and/or riveted or forged into spikes, ladders, iron frame, balusters, railings, cooler stand and similar works conforming to Fe.290, Gde-E-165including one shop coat of zinc chrome primer and cutting holes/making surface good in cement concrete 1:2:4 type B-0 complete all as specified and as directed. |
| 53 | S&F 0.9m to 1.5m bottom door seal brown aluminium frame 38 to 45mm width all as specified and directed. |
| 54 | M&L for preparing the new wooden surface & applying two coats of synthetic enamel paint (1st grade) over one coat of pink primer over 10Cm width or girth complete all as spd & directed. |
| 55 | M&L for preparation of new steel surfaces over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 56 | S&F SS wire cloth0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames withtinned tacks or galvanized wire staple & complete all as specified and as directed. |
| 57 | S&F in repair SS wire cloth0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames withtinned tacks or galvanized wire staple & complete all as specified and as directed. |
| 58 | S&Fdoor stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor over all length of cover plate 150 mm all as specified and directed. |
| 59 | S&F mild steel helical door spring 300mm ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed by Engr-in-charge. |
| 60 | S&F 100 mm long SS butt hinges, medium weight, cold rolled, ISI marked, complete all as specified and as directed. |
| 61 | Supply & fix only 100 mm longmild steelbutt hinges, medium weight, cold rolled and fixed with screws/welded complete all as specified and directed. |
| 62 | S&F 125mm size aluminium alloy handles, fabricated type extruded section, ISI markedcomplete all as specified and as directed. |
| 63 | S&F 150mm size aluminium alloy handles, fabricated type extruded section, ISI markedcomplete all as specified and as directed. |
| 64 | S&F 100mm size stainless steel handles, for cupboard/ kitchen cabinet complete all as specified and as directed. |
| 65 | S&F for aluminum anodized barrel tower bolt of extruded section size of bolt 150mm as specified and directed. |
| 66 | S&F aluminum anodized barrel tower bolt of extruded section size of bolt 200mm as specified and directed. |
| 67 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed |
| 68 | Taking up or down 15 mm bore dia GI steel tubing and connectionscomplete all as specified and as directed. |
| 69 | Taking up or down 20 mm bore dia GI steel tubing and connectionscomplete all as specified and as directed. |
| 70 | M&L for 15mm bore CPVC pipesSDR 11 & Plain CPVC SDR 11 fittings such as socket, elbow, bends, tee, reucer, union, caps plug, nipple etc complete laid in walls/ceilings or laying in floor trench or fixed to walls complete all as specified and as directed |
| 71 | M&L for 20mm bore CPVC pipesSDR 11 & Plain CPVC SDR 11 fittings such as socket, elbow, bends, tee, reucer, union, caps plug, nipple etc complete laid in walls/ceilings or laying in floor trench or fixed to walls complete all as specified and as directed |
| 72 | M&L for cutting chases in walls for pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girthall as specified and as directed. |
| 73 | S&F in repairs Vitreous China wash basin, white, of size 550x400mm including brackets, Waste Pipe, CP Waste coupling 32mm of bore, PVC connection pipe complete all as specified and directed.Note: Cat No S2040141 of CERA or equivalent model of makes Specified. |
| 74 | S&F in repairs Vitreous China wash basin, white, under counter type, oval, of size 520x450x190mm (minimum), including fixing in granite counter with Waste Pipe, CP Waste coupling 32mm of bore, PVC connection pipe complete all as specified and directed.Note: Cat No S2030101 or S2030104 of CERA or equivalent model of makes Specified. |
| 75 | M&L in repairs, viterous China bowl urinal flat back, size of 340X280X470 mm (minimum),white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe) includingurinal spreader of brass chromium plated for fixing with 15 mm dia pipe,PVC connection, 40mm PVC Waste pipe, and 40mm waste coupling providing and fixing plugs, bedding urinals against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long screws, pointing around urinal back in cement fixing flush pipe complete all specified and as directed.Note: Cat No S4020103 of CERA or equivalent model of makes Specified. |
| 76 | S&F in repair Vitreous China, white Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) includingtrap, and flushing pipeanti syphonage pipe ,set in cement concrete as specified complete all as specified and directed. |
| 77 | S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, including plastic white seat cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and as directedNote: Cat No S1053102 of CERA or equivalent model of makes Specified. |
| 78 | S&F in repair PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacityWhite, with inlet ball valve, float, handlewith 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.Note: Cat No B1010110 of CERA or equivalent model of makes Specified. |
| 79 | S&F in repair PVC connection,15 mm size with PTMT nuts,450 mm longcomplete all as specified and directed. |
| 80 | S&F in repairs PVC waste pipe32mm bore plain600mm long complete all as specified and asdirected. |
| 81 | S & F stainless steel grating with square frame (grating thickness 1mm and frame thickness 1.5mm) of size 125mm (minimum) with waste hole complete all as directed. |
| 82 | S&F in repair Soap dish, chromium plated, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed. |
| 83 | S&F in repairs,Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.Make :- Cat No F8030111AB of Cera or equivalent model of makes specified. |
| 84 | S&F in repairs, 15 mm bore pillar taps, swan neck type, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered \"HOT\" or \"COLD\" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.Make : Cat No.F1015103/F1015104 of CERA or equivalent model of makes specified. |
| 85 | S&F in repair 15mm borewall mixer for mixing hot & cold water and bend to connections to shower, 15mm bore screwed for iron pipe and fixed complete all as specifiedand directed.Make :- Cat No F1015401 of Cera or equivalent model of makes specified. |
| 86 | S&F in repairs 15mm bore brass chromium plated centre hole basin mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make :- Cat No F2014461 of Cera or equivalent model of makes specified. |
| 87 | S&F in repair over head shower roses 125mm size with 200mm long shower arm and wall flange all as specified and directed by Engr-in-charge.Make :- Cat No F7020111AB of Cera or equivalent model of makes specified. |
| 88 | S&F in repairs, angle/ stop cock 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.Make:- Cat No F1015201 of Cera or equivalent model of makes specified. |
| 89 | S&F in repairs, bib tap 15mm dia, with wall flange and areator screws down for iron pipe or for iron pipe or for brass ferrule complete all as specified and as directed.Make :- Cat No F1015151 of Cera or equivalent model of makes specified. |
| 90 | S&F in repair 15mm bore chromium plated two way angle cock, screwed down,high pressure, for iron pipe and fixed, complete all as specified & directed.Make :- Cat No F2002211 of Cera or equivalent model of makes specified. |
| 91 | S&F in repairstowel rail60 cm long between flangescomplete all as specified and as directed.Make: Cat No. F5015103CH of CERA or equivalent model of makes specified. |
| 92 | S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all asspecified and directed by Engr-in-Charge |
| 93 | S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass cornershelf 300mm radius complete all asspecified and directed by Engr-in-Charge. |
| 94 | Labour only for taking down sinks with drainage board and refixing the same with cantilever brackets and connecting union to pipe complete all as specified and as directed. |
| 95 | S&F kitchen plate rack of overall size 786mm x760mm x 254mm made out stainless steel sheet not less than 0.63mm thick, design and pattern as approved by GE and fixed to wall with wooden plugs with chromium plated screws and cup washers complete all as specified and as directed. Make : Prayag cat No P-446/ Silvershine cat No SSKPR-314 or equivalent model of makes specified. |
| 96 | S&F in repair bevelled edge looking mirror 5.5mm thick mirror of selceted glass mounted on BWP commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screwscomplete all as specified anddirected by Engr-in-charge.Note: Size as decided by Engineer-in-Charge |
| 97 | S&F in repair bevelled edge looking mirror 5.5mm thick ofsize 600mm x 450mm mounted on commercial plywood 6 mm thick including PVC beading all round and fixed to wooden plugs with chromium plated screwscomplete all as specified anddirected by Engr-in-charge. |
| 98 | S&Fin repairs, rotational moulded polyethylene water storage tanks colour white(cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia float valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed. |
| 99 | S&Fin repairs, rotational moulded polyethylene water storage tanks colour white(cylindrical vertical with closed top),1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia float valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed. |
| 100 | S&Fin repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20mm dia, ISI marked complete all as specified & as directed. |
| 101 | S&F in repairs, 20mm dia stainless steel curtain rod with brackets and finials at both ends as per site requirement including taking down old curtain rods with accessoriescomplete all as specified and as directed.Note :- The Cost of brackets and knobs shall deemed to be included in the quoted rate. |
| 102 | M&L for water proofing treatment tofloor and vertical surfaces of sunken portion complete comprising the following (floor area WC/Bath/kitchen not exceeding 1.5 Sqm) :- (a) After demolition of floor and lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water.(b) Brushing cement slurry with 1.2 kg of cement per square meter duly blended with & including water proofing compound.(c) 15mm thick (Average thickness) plaster in cement mortar (1:4) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. |
| 103 | (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non-woven fabric (weight not less than 150 gm/sqm (e) M&L for PCC 1:7:12 for fillin of sunken portion after conceling all membrane and sealing all joints to the entire with broken bats and light weight, floor area of WC/Bath not exceeding 1.5 sqm and provide hole in the wall and fix 600 mm long 20 mm dia GI spouts lightgrade, PCC 1:3:6, type C1 (using 20 mm graded stone aggregates) filling complete allas satisfaction of Engineer-in-Charge.Note- The rates include for drilling of the hole RCC @ 1.00 m centre to centre, to a depth to a length of 30 mm and fixing of PVC pipes of dia 15/20 mm laid dry and groutingwith cement slurry mixed with can bax 100 chemical with pressure grouting with minimm 3 Kg/Sqm complete all as specified and directed |
| 104 | All as per item No 102.00 here-in-before but floor area of WC/Bath/kitchen exceeding 1.5 sqm and not exceeding 3 sqm |
| 105 | S&F in repairs 75 mm dia PVC(SWR) nahani/ floor trap withgrating including jointing to waste pipe with solvent cement complete all as specified and as directed. |
| 106 | S&F for providingCupboard/kitchen cabinet with shutters in required size atsite made out of 18 mm thick solid PVC board one side laminated and other side plain. The panels shall be fabricated using adhesive, screwed and secure as required.All edges shall be covered with 1.5mm thick edges leaping tapes or 90 degree edgebent finish as per manufactures instructions complete all as specifed and directed. |
| 107 | S&F for providingCupboard/kitchen cabinet Shelf in required size atsite made out of 18 mm thick solid PVC board bothsides plain. The panels shall be fabricated using adhesive, screwed and secure as required.All edges shall be covered with 1.5mm thick edges leaping tapes or 90 degree edgebent finish as per manufactures instructions complete all as specifed and directed. |
| 108 | S&F continous (Piano) hinges, brass finish of30mm width of flaps when open complete all as specified and as directed |
| 109 | S&F 100mm size hasp and staple, aluminium anodisedsafety type, fixed with screws complete all as specified and directed |
| 110 | S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed |
| 111 | S&F in repair magnetic catcher, Double strip (horizontal type),in cupboard/ward robe shutters including fixing wit necessary Stainless Steel screws etc. complete all as specified and as directed. |
| 112 | S&F in repair for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed. |
| 113 | S&F in repairfor 110 mm bore PVC (SWR) pipes single socketed with rubber ring joints, laid in trenches or in floors complete all as specified & directed. |
| 114 | S&F in repairfor 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed. |
| 115 | S&F in repairfor 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed. |
| 116 | S&F in repairs, 110 mm dia PVC (SWR) bends with oval access doorof any radiuscomplete all as specified and as directed. |
| 117 | S&F in repairs, 75 mm dia PVC (SWR) bends with oval access door of any radiuscomplete all as specified and as directed. |
| 118 | S&F in repairfor 75 mm bore PVC (SWR) junction single, (Single Y) equal or unequal complete all as specified & directed. |
| 119 | S&F in repairfor 110 mm bore PVC (SWR) junction single, (Single Y) equal or unequal complete all as specified & directed. |
| 120 | S&F in repairfor 75 mm bore PVC (SWR) junction double, (double Y) equal or unequal complete all as specified & directed. |
| 121 | S&F in repairfor 110 mm bore PVC (SWR) junction double, (double Y) equal or unequal complete all as specified & directed. |
| 122 | S&F in repairfor 75 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & directed. |
| 123 | S&F in repairfor 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified & directed. |
| 124 | S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 125 | S&Fstack clamp made out of 50 x 3mm flat iron and 16 mm dia round iron stays fixed to wall for pipe of bore 110mm complete all as specified. |
| 126 | S&F PVC bend/ shoe of dia. 110mm complete all as specifiedcomplete all as specified. |
| 127 | S&F in repairs 110mm bore PVC (SWR) reducer complete all as specifiedcomplete all as specified. |
| 128 | M&L for 15mm thick plaster in CM 1:4 (using water proofing liquid as per manufacturers instructions) on concrete surfaces of sunken portion. The corners of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate the pipe and curing of sunken portion shall be carried out with water for a minimum of 48 Hrs by ponding complete all as specified and directed.Note : Water proofing liquid shall be paid separately. |
| 129 | M&L for Brushing cement slurry @ of 1.2 Kg of cement per square metre duly blended with & including water proofing compound complete all as specified and directed. |
| 130 | S&F APP polymer modified prefabricated membrane using Butane torch by torch applicationwith 100mm side laps APPmembrane shall be ofminimum weight not less than 3.6 Kg/Sqm and minimum 3mm thickfive layered reinforced with non woven polyester fabric (weight not less than 150 gm/sqm) over a coat ofbitumen primer @ 0.40 liter/sqm on prepared surface complete all as specified and directed. |
| 131 | M&L for PCC (type F-2) 1:7:12 for filling of sunken portion after concealing all membrane and sealing all joints complete all as specified and directed. |
| 132 | M & L for providing hole in the wall and fixing600 mm long, 20mm dia GI spouts light grade including packing and filling holes around pipes with PCC 1:3:6 type C0 (using 12.5mm graded stone aggregate) complete to thesatisfaction of Engineer-in-Charge. |
| 133 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay,complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 134 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay,complete without glazing bars, dovetailed or welded complete all as specified and as directed. |
| 135 | Hacking out of old broken glass (any thickness ,size quality or description/ any height of bldg ) fromwooden / metal frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed. |
| 136 | S&F3 mm thick frosted/figured glass, pin headed type and glazing with oil putty in square not exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed. |
| 137 | S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or beads in square n.exc 0.50 sqm in each pane, of any description complete all as specified and as directed. |
| 138 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for ( reinforcement cut as required to facilitate demolition) complete all as specified and as directed. |
| 139 | M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works flat n exc 200mm thick (Horizontal or slopping) for fair finished surfaces complete all as specified and as directed. |
| 140 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed. |
| 141 | M&L for form work to edges of concrete flats, treads floor and roofs n exc 20 cm wide and sides of RCC/PCC bends in walls (horizontal or slopping) and similar works exc 10 cm but n exc 20 cm wide for fair finished surfaces complete all as specified and directed. |
| 142 | M&L for mild steel TMT bars, 8mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 143 | M&L for mild steel TMT bars 5mm and over upto and including 10mmdia, cut to length, bent to shape required, including crankng as in stirrups with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed. |
| 144 | M & L for RCC 1:2:4 (Nominal Mix), type B-1, using 20mm graded crushedstone aggregateas in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and shelves and the like etc .complete all as specified and as directed. |
| 145 | M&L for RCC 1:2:4 (Nominal Mix) type B1 using 20 mm graded stone aggregate Foundations, beams, plinth beams,base of column,lintel band,roof beam etc complete all as specified and directed by Engineer-in-Charge. |
| 146 | Resecuring or easing of steel window/door shutters not exc 2.00 sqm eachincl fixing of screws, adjusting handles, knobs, tightening hinges, welding, incl misc small adjustments, replacement of unserviceable hinges complete all as specified and as directed. |
| 147 | M&L for 40 mm thick, cement concrete 1:2:4, type B1(using 20 mm graded stone aggregates) as in path/hard standing and flooring, laid in alternate bays, finished even & smooth without using extra cement including necessary formworkcomplete all as specified and as directed. |
| 148 | M&L for PCC (1:3:6) type C-1 using 20mm graded stone agg as in coping, on top of wall, bed blocks for hold fast, lintel band upto 1.5 mtr span and the like including weathering,slightly rounded or chamfered angles and throating as directed by Engr-in-Charge including use of necessary form work. |
| 149 | M&L in repairsfor water proofing treatment to RCC roof slab, including parapet, comprising with the followingtreatment/specification from bottom to top:-(i) Taking out old roof treatment and roughening the old concrete slab by picking, sweeping clean and washing down with water to remove dust etc and disposal of rubbish outside MD land.(ii) Screed bed or bedding layer of 10 mm thickcement mortar 1:4 with mixing of WPC @ 3% by weight of cement or as per manufacturers instructions and surface finished even and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. |
| 150 | (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.40 ltr /Sqm conforming to IS:3384-1986.(iv) APP based polymeric membrane 3mm thick (minimum),weighing 3.6 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall beapplied over bituminous primer as specified above by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction.(v) Applying two coat of Bituminous aluminium paint over the APP modified membrane @ 0.11 Kg/sqm.Note: Cost of Water proofing compound shall deemed to be included in the quoted rate. |
| 151 | Excavation in trenches not exc 1.50m wide and not exc 1.50m deep for foundation etc . or laying of pipes, cables or shafts, wells, cesspits, manholes, pier holes,etc. n. exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and as directed |
| 152 | M&L Returning, refilling in trenches, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. |
| 153 | Removing excavated surplus soil to a distance n.exc. 50 mand depositing where directed at a level not exceeding 1.5 m from the starting point complete all as specified and as directed. |
| 154 | Removing excavatedsoil to distanceexc250m but n.exc 500 m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed. |
| 155 | M&L for supply, laying, jointing and testing of RCC pipes, 150 mm bore dia, class NP2, laid in trenches and jointed with collars in cement mortar 1:1, including demolition of PCC in bedding/haunching with taking down of old RCC /SGSW pipes of 150mm dia and removal of debris out from defence landcomplete all as specified and as directed. Note:- (a) Excavation, earthwork and PCC bed concrete shall be measured and paid for seperately under respective item. |
| 156 | M&L for PCC 1:4:8, type D-2, using 40 mm graded stone aggregates as in concrete bed for 150 mm bore dia drain pipes, any type,including packing under and haunching against the sides of the pipes after they are laid & tested complete all as specified and as directed. |
| 157 | Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc and matching with existing surface complete all as specified and as directed. |
| 158 | M & Lpoint wiring complete with and including single core PVC insulated unsheathed flexiblebright annealed multi stranded copper conductorFRLS (H) cables 1.5 Sqmm (22/0.30 mm) 1100 volts grade drawn through and including heavy grade PVC rigid conduits 20 mm or higher dia as reqd at site,totally concealed inwalls/floors/ceilingincluding all conduit accessories/ fittings/ junction boxes/ inspection covers etc; of heavy grade, ISI marked and sunken terminal boxes of factory made 16 SWG pressed steel housing, totally concealed in wallswith 3 mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws |
| 159 | and sunk/cup washers, for mounting of switches, sockets fan regulates etc; including 1.5 Sqmm (22/0.30 mm) 1100 V gradePVC insulated, unsheathed flexiblemulti stranded copper conductorFRLS (H) cable as continuous earth wire connected to metallic bodies of luminaries/fans etc; at one end and to common earth dolly at other end, all as specified & directed forlight point or one fanpoint controlled by one, one way switch (Note: The unitrate quoted shall deeemed to be included cutting chases in walls for concealed wiring & making gooddisturbed surfaces . |
| 160 | All as per serial item No 156.00 but for one bell / buzzerpointcontrolled by one push button on the same board with other switches or independent board |
| 161 | All as per serial item No 156.00but for one 3 pin 6 Amp Socket outlet point on same board with other switches including earth wire as per description given above and connected to common earth and earth terminals. |
| 162 | All as per serial item No 156.00 but for one 3 pin 6 Amp Socket outlet point on independent board including earth wire as per description given above and connected to common earth and earth terminals. |
| 163 | All as per serial item No 156.00 but for one light point controlled by two way switches. |
| 164 | All as per serial item No 156.00but with 2.5 Sqmm cables for one 16A, 6-Pin (multipurpose) socket outlet pointon independent board with & including 2.5 Sqmm FRLS (H) cable as earth wire complete all as specified and as directed. |
| 165 | All as per serial item No 156.00but with 4.0 Sqmm cables for one geyser pointon independent board with & including 4.0 Sqmm FRLS (H) cable as earth wire complete all as specified and as directed. |
| 166 | S&F Modular switch single pole one way6/10 Amps 1 module complete all as specified and as directed. |
| 167 | S&F Modular switch single pole one way 16 Amps 1 module complete all as specified and directed. |
| 168 | S&F ModularBell Switch 5/6 Amp 1 Modulecomplete all as specified and as directed. |
| 169 | S&F ModularSwitch 2 way 1 module complete all as specified and as directed. |
| 170 | S&F Modular socket 6 Amp-2/3 pin combined 2module complete all as specified and as directed. |
| 171 | S&F Modularsocket 6 A/16 Amp -2/3 pin combined 2 module complete all as specified and as directed. |
| 172 | S&F Modular fan regulator Step Type, 120W-2 Module Complete all as specified and as directed. |
| 173 | S&F in replacement decorative ultra slim batten square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficientof capacity 20 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make : Cat No.LHEXAWP7UN1W020 of Havells or equivalent of makes specified in PS |
| 174 | S&F in replacement decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficientof capacity 10 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make : Cat No.LHEXAZP7PN1W010 of Havells or equivalent of makes specified in PS |
| 175 | S&F in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. |
| 176 | S&F in replacement LED light fitting 1x 9W / 1X10W bulkhead luminaires including LED light driver holder connecting up with two core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 177 | S&F ceiling rose surface bakelite three terminal type complete all as specified and as directed. |
| 178 | S&F in replacement of bell multi music type, AC, 230 volts, single phase complete all as specified and as directed. |
| 179 | S&F in repairs, MCB DB, double doortype(when MCBs are to be used),triple pole and neutral, 415 volts, 4 way,protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copperbusbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed. |
| 180 | S&F in repairs, MCB DB, double doortype(when MCBs are to be used),triple pole and neutral, 415 volts, 8 way,protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copperbusbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed. |
| 181 | S&F in repairs, MCB DB, double doortype(when MCBs are to be used), single pole and neutral, 240 volts,12 way,protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copperbusbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed. |
| 182 | S&F in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240 Volts complete all as specified and as directed. |
| 183 | S&F in replacement of MCB SP, C Curve, 6 to 32 Amps 10 KA single pole AC 230volts complete all as specified and as directed. |
| 184 | S&F in replacement of MCB SPN, C Curve, 40-63 Amps 10 KA single pole AC 230volts completeall as specified and as directed. |
| 185 | S&F in replacement of MCB C Curve TPN 40-100 Amps, 415 V complete all as specified and as directed. |
| 186 | Supply & fix Emergency/Inverter lamp in replacement of old Bulb any typewith Emergency Back up up to 3-4 Hrs High grade thermal plastic housing with Al Heat sink for better thermal management , 100 lumen/watt PF>0.90 operating voltage 100 to 300 V Eco friendly (No Mercury) CCT 6500 of capacity 12 watt complete all as specified and directed.Make : Cat No.LED 12 W B22 CDL INVERTER BULB V2 of Havells or equivalent of makes specified in PS |
| 187 | S&F in replacement, LED bulb 9/10Watt 230 volts 50 Hz AC complete all as specified and directed by Engineer-in-charge.Make: Havells Cat part No. LHLDDEBNL5R10or equivalent model of makes specified in PS. |
| 188 | S&F in replacement Emergency / Inverter LED batten 20W 6500K with square profile and polycarbonate channel, lithium-Ion battery with charging time 8hours-10 hours, back up time up to 4 hours and surge protection up to 4KV including connecting up with suitable flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.Make : Cat No. LHEXASP7IN1W020 Pride Plus Inverter Batten 20W 6500 KV1 of Havells or equivalent of makes specified in PS |
| 189 | M&L for sub main wiring with 2 runs of 4 sqmm, single core, PVC insulated & unsheathed FRLSH cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawndrawn through concealed conduit and including PVC conduit heavy grade alongwith one run of 4 sqmm single core PVC insulated & unsheathed FRLSH copper conductor as continuos earth wire and connecting to common earth terminalsand testing on completion including taking down old submain wiring and casing caping complete all as specified and as directed.NOTES: (a) Proper colour coding shalladopted for wiring (for phase-RED, YELLOW, BLUE for Earth- Green and Neutral-Black) (b) Three runs of 4 sq.mm cable and one run of PVC conduit shall be measured as one unit |
| 190 | M&L for sub main wiring with 2 runs of 6 sqmm, single core, PVC insulated & unsheathed FRLSH cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn through concealed conduit and including PVC conduit heavy grade alongwith one run of 6 sqmm single core PVC insulated & unsheathed FRLSH copper conductor as continous earth wire and connecting to common earth terminalsand testing on completion including taking down old submain wiring and casing caping complete all as specified and as directed.NOTES: (a) Proper colour coding shalladopted for wiring (for phase-RED, YELLOW, BLUE for Earth- Green and Neutral-Black) (b) Three runs of 6 sq.mm cable and one run of PVC conduit shall be measured as one unit. |
| 191 | Supply & fix in replacement exhaust fans PVC bodyAC single phase 230/ 240 V of size 300 mm sweep,1760 RPM,air delivery 252 CMH with louver electrical connectionfrom ceiling rose to Exhaust Fan complete all as specified and as directed by Engineer in Charge. |
| 192 | M & L for Taking downcarefully water Geyser 25 ltrs capacity by unscrewing nuts bolts, water inlet/outlet pipes from walls/foundation complete including refixing in position after carrying repairs like change of suitable geyser element,themostat,inlet outlet pipes,16 Amp plug top,replacement of burnt wire,safety valve,non return valve,inner and outer tank,sloving geyser leakage problems etc. including making connection to the water inlet, outlet pipe, electric connection and testing complete all as specified and directed by Engineer-in-charge. |
| 193 | Supply, laying,testing and commissioning of UG LT cables, 50 Sqmm x 3.5 core, 1100 volts grade, XLPE insulated, screened and PVC sheathed, galvanised steel strip or wire armoured with multi stranded aluminium conductor, ISI marked, heavy duty including cable glands, cable lugs in LT panel/MDB in building etc to suit the cableincluding material and labour for all jointing/connecting material as requiredsize, cables laid in trenches/ducts/under plinth floors passing through pipes etc, fixed on wall including taking out old cable and cable covers complete all as specified and directed. |
| 194 | Supply and laying Double Walled Corrugated (DWC) HDPE pipe of nominal bore 63mm including 90 degree bends with coupler and rubber ring, conforming to IS :16205 Part 24 Type 450N, laid in trenches for cable protection complete, all as specified and as directed. |
| 195 | M&L in replacement for GI tubing 40 mm bore light grade for protection of cable with all necessary fittings accessories such as MS 40x3mm clamps of suitable length, nuts, bolts and washers and fixed complete towall/ceiling or laid under floors complete all as specified and as directed. |
| 196 | S&Fin replacement 35 Wattbuilding mounted LED security light fitting complete made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2m long bend to shape requiredfixed to pole / wall with 02 Nos MS clamps made out of flat iron 40x5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting complete all as specified and as directed.Make : Havells Cat No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model of makes specified. |
| 197 | M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia, by means of nut bolts, check nuts and washer andthe GIEarth wire connected upto main earth point/DBs alongwith 15mm dia GI medium grade protection pipeincluding provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4)cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape,GI light grade |
| 198 | 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh andearth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.Note : Rate of GI earthwire and GI protection pipe upto 7.5 mtr length shall be deemed to be included in this item |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
