|
| 1 | Dismantling framed trusses of span exc 10m but n exc 15m all as specified and directed. |
| 2 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings |
| 3 | Dismantling Stone sett paving laid dry or laid dry and pointed of any description or thickness all as specified and directed. |
| 4 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground Posts embedded in Concrete, brick work, masonry, etc as specified and directed |
| 5 | M & L for Dismantling of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as specified and as directed. |
| 6 | Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed |
| 7 | Demolition of reinforced cement concrete in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended workreinforced (reinforcement cut as required to facilitate demolition) all as specified and directed |
| 8 | Separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately) complete all as specified and directed. |
| 9 | M&L for Drilling & chemical anchoring of new rebars/stirrups:Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling upto 10 mm dia bar will be upto 300 mm.Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF , FOSROC Lokfix E77 or equivalent of SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item) |
| 10 | M&L for Drilling & chemical anchoring of new rebars:-Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling for 16 & 20 mm dia bar will be upto 300 mm.Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF , FOSROC Lokfix E77 or equivalent of SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)Note for srl item no 9 & 10 :- Reinforcement shall be measured and paid separately in respective item. |
| 11 | M& L for Running Welding in repairs(continuous welding with 20mm dia existing TMT bars) on both sides in length,thickness of steel barsto be welded exceeding 9mm but n.exc 20mm all as specified and directed |
| 12 | Tanking down Chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each |
| 13 | Dismantling Brick tiles or terracing tiles, single layer on roofs including any other treatment complete all as specified and as directed |
| 14 | Demolition of Mud in roofs (mud phuska), any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and throwing rubbish off the premises complete all as specified and as directed |
| 15 | Excavating over areas,n exc 1.5 m deep and getting out as directed by Engineer-in charge in hard/dense soil as specified and directed |
| 16 | All as per Srl item No 15.00 but exc 1.5m and n.exc 3.0m depth |
| 17 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil. |
| 18 | M & L for Cement concrete Type D21:4:8(40 mmgraded aggregate) infoundations, filling and mass concrete complete all as specified and as directed |
| 19 | M & L for Reinforced cement concrete (design mix) M-30 (20 mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed |
| 20 | M & L for Reinforced cement concrete M-30 (Design mix)(20 mm graded aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed |
| 21 | M & L for Reinforced cement concrete M-30 (Design mix) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed |
| 22 | M & L for Reinforced cement concrete M-30 (Design mix) Chajjas complete all as specified and directed |
| 23 | M & L for Reinforced cement concrete M-30 (Design mix) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed |
| 24 | S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 25 | All as per Srl Item No 24.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders |
| 26 | M & L for fair finish flat Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batterall as specified and directed |
| 27 | M & L for fair finish flat surface of Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed |
| 28 | M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed |
| 29 | M & L for Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed |
| 30 | M & L for fair finish flatFormwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 31 | M & L for Brick work with sub- class ‘B’ bricks (old size), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed |
| 32 | M & L for Brickwork with subclass ‘B’ bricks (old size), straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed |
| 33 | M & L for Sand filling under floors or in foundations including watering and consolidation all as specified and as directed. |
| 34 | M & L for Hardcore of guage exc 63mm but n exc. 100 mm, with broken stone orboulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/ rammed to a true surface all as specified and as directed |
| 35 | M & L for 100 mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub-base for floor complete all as specified and as directed. |
| 36 | M & L for Double charged high gloss Vitrified tiles any shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in CM 1:6 complete all as specified and directed |
| 37 | All as per Srl item No 36.00 but on vertical surface such as skirtings, dado, and risers to steps etc over 10mm thick cement plaster in CM 1:4complete all as specified and directed |
| 38 | M & L for Coloured Glazed ceramic tiles in vertical surface 450X 350X 7mm thick over & including 10mm thick palster in CM 1:4set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed |
| 39 | M & L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in CM 1:6 complete all as specified and directed |
| 40 | S & F Vitreous China urinals, bowl type (back or corner wall type), Size 360-400X350-400X575-710 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) with Waste coupling 32mm bore of PTMT (half or full threaded) suitable for urinals, (Minimum weight 32mm-45gms and Push tap 15mm bore any colour high pressure of PTMT screwed for iron pipeand fixed, (Minimum weight 15mm-47gms/20mm- 75gms)complete all as specified and as directed. |
| 41 | S&F in repairs Vitreous china wash down water closet pan wall mounted complete single unit including double syphonicflusing cistern white, seat cover including connection to drain trap complete. all as specified and directed. |
| 42 | S&F wash hand basin Counter Top , white, flat back, size 550 x 450 x 200mm)) , including cuttingand orall as specified and directed. (Including 15mm borepillar tap brass with premium chrome finish and foam flow, waste coupling and 32mm dia PVC waste pipe) complete all as spd. |
| 43 | S&F 15mm dia Stop valve of PTMT any colour high pressure screwed for iron/CPVC pipe and fixed (Minimum weight 90gms) complete all as specified and directed |
| 44 | S & F Gun-metal, globe or gate valves, 25mm bore with iron wheel head, screwed both ends for iron/CPVC pipe and fixed complete all as specified and directed |
| 45 | Supplying and laying of CPVC pipes 16mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 46 | All as per Srl item No 45.00 but 25 mm outer dia |
| 47 | S & Ffancy type Bib tap 15mm dia of PTMT any colour high pressure screwed for iron/CPVC pipe (Minimum weight 15mm-105gms) complete all as specified and directed |
| 48 | S &F fancy type Pillar taps of PTMT any colour high pressure screwed for iron/CPVC pipe (Minimum weight 15mm-120gms) complete all as specified and directed |
| 49 | S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 50 | S & F Brass Chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed |
| 51 | S & F Rotational moulded polyethylene water storage tanks 750 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified and as directed |
| 52 | S & F 25mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron/CPVC pipe and fixed. (Minimum weight 455gms) |
| 53 | S & FSoap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall all as specified and directed |
| 54 | S&F 6mm thick bevelled edged, fixed with stud- type looking mirror of size 900x600mm , made from selected glass quality, with an minimalist frame with an antique finish, securly mounted to the wall, complete all as specified and as directed |
| 55 | S & F PVC (SWR) floor trap, plain with grating including jointing with solvent cement 50mm outlet and fixed with PVC Pipe 50mm dia complete all as specified and directed |
| 56 | S & F High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls,ceilings or in floors etc 50mm bore fixed with floor trap all as specified and directed |
| 57 | S & F PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls as rain water pipe complete all as specified and directed |
| 58 | S & F PVC (SWR) bends 110mm dia fixed with PVC rain water pipe with rubber ring joint and solvent cement all as specified and directed |
| 59 | S & F Factory made single extruded WPC (Wood Polymer Composite) soliddoor/window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) all as specified and directed |
| 60 | S & F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paidseparately) all as specified and directed |
| 61 | S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and directed |
| 62 | S & F Butt hinges, 100mm longSS, all as specified and directed |
| 63 | S & F SSbarrel tower bolts 150mm long of extruded section and fixedas specified and directed |
| 64 | S & F 250mm longSS sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed as specified and directed |
| 65 | M & L for Rendering 10mm thick in CM 1:4 (for roof treatment)on fair faces of brick work or concrete surfaces (when concrete is green) of any description finished even and smooth without using extra cement, mixed with liquid water proofing compound complete all as specified and as directed. |
| 66 | M & L for 40mm thick (average thickness) Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in roof padding finished even and sooth and maintaining the required gradient to receive APP based water proofing treatment all as specified and directed |
| 67 | M & L for roof treatment through manufacturer/authorized applicator of the manufacturer as approved by AGE (I) by applying a coat of cold applied bituminous old based primer over cleaned surface @ 0.30 Kg/Sqm and applying one coat of hot blown bitumen VG-30 grade @ 1.00 Kg/Sqm after a interval of minimum 8 hrs of priming and applying of APP modified five layer polymeric membrane emm thick, minimum weight 3.6 Kg/sqm reinforced with polyster non-woven febric (weighing not less than 150 gms/Sqm) with troch application method after a interval of minimum 8 hrs of hot bitumen coating by authorised applicator of approved manufacturers, laid as per the manufacturers instruction with side over lap of 75mm and end overlap of 100mm & tucked into the chases on vertical surfaces. |
| 68 | S & F Heat resistance Terrace Tiles (300mm X 300mm X minimum 10mm thick) with SRI (Solar reflective index) >78, solar reflection >0.75 and initial emittance > 0.75 on water proof and sloped surface of terrace, laid on 20mm thick cement sand motar in ration of 1:4 (1 cement : 4 coarse sand) and set and jointed with epoxy tile grout to match the colour of tiles complete including providing skirting along the parapet walls of height as directed in the same manner including 15mm thick backing coat in cement motar 1:4 complete all as specified and directed |
| 69 | S & F Anodised aluminium Powder coated min thickness of coating 50 micron frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 70 | S & F Anodised aluminium Powder coated min thickness of coating 50 micron door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprenehandles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. |
| 71 | M&L forpowder coated Anodised aluminiumthree way track sliding windows of frame size 92mmX31.75mmX1.5mm thickness (section No 20831 of JINDAL) and of shutter size 40mmX18mm (with 9.00mm interlocking legs) X1.45mm thickness (Section No 20737 of JINDAL) section (two shutter glazed,covering half of span of opening each & one shutter skeleton covering half of span opening) incl provn for making windows air tight, including 95mm aluminium handle with spring lock, stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperature 1.4mm and fixed with wire stapples and 5mm thick plain glass including necessary fitting/fixture/aluminium snap beads complete all as specified and as directed |
| 72 | S & F Anodised aluminium Powder coatedventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminiumsnap beading, screws etc. complete all as specified |
| 73 | S & F 5.5 mm thick Sheet glass in square n exc 0.5 Sqm in each pane, ordinary quality and fixed to aluminium door and window shutter with rubber gasket, glazing pin etc all as specified and as directed |
| 74 | All as per Srl Item No 73.00 but exc 0.5 Sqm in each pane. |
| 75 | S & F 150mm Extruded aluminium alloy handles, fabricated type, anodised for aluminiun door shutter fixed with aluminium/ss screw all as specified and directed |
| 76 | S & F 100mm long Butt hinges, extruded aluminum alloy with galvanised mild steelhinge pin, anodised and fixed to aluminium door shutter with aluminium/SS hinges all as specified and directed |
| 77 | S & F Aluminium alloy, anodised, 250mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed to aluminium door shutter all as specified and as directed. |
| 78 | S & F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed to aluminium door shutter all as specified and as directed. |
| 79 | S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 80 | S &F Aluminium extruded section bodyDoor closer hydraulically regulated, designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed |
| 81 | M & L for Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of any description, finished even & smooth (without using extra cement) complete all as specified and as directed. |
| 82 | M & L for Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces of any description, finished even & smooth (without using extra cement) mixed with liquid water proofing compound complete all as specified and as directed. |
| 83 | M & L for Rendering 5mm thick in CM 1:3 on concrete surfaces as in ceilings, finished even & smooth (without using extra cement) complete all as specified and as directed. |
| 84 | M & L for 1mm thick wall care putty on wall finished even and smooth to receive paint complete all as specified and directed |
| 85 | M & L for 1mm thick wall care putty on ceiling finished even and smooth to receive paint complete all as specified and directed |
| 86 | M&L for cutting channels, grooves or rebates n exc 15cm girth, and trimming surface complete all as specified and directed |
| 87 | M & L for Providing, cement concrete type B-0 1:2:4 (12.5 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges as specified and as directed. |
| 88 | Supply only Liquid water proofing compound |
| 89 | Material & Labour for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete on walls/ceiling surface, as per manufacturer\"s specification. Two or more coats on new work complete all as specified. |
| 90 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified. |
| 91 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified and as directed. |
| 92 | Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed all as specified and directed. |
| 93 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified. |
| 94 | Supplying and laying 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed |
| 95 | M & L for Concrete bed with cement concrete type C2 1:3:6 to 150mm bore to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested; inall as specified and as directed |
| 96 | Cutting into existing manholes for connecting new drains 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required as specified and directed |
| 97 | Material & Labour for complete removal of existing surfaces and preparation and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm. |
| 98 | M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade including 15mm thick screed bed in CM 1:4 of granite all as specified and as directed. |
| 99 | Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete. |
| 100 | Material and labour ofor one light point or one fan point controlled by one switch with and including single core FRLS PVC insulated unsheathed, multistranded copper conductor cable of size 1.5 Sqmm 1100V grade drawn through and includingPVC conduit size not less than 20 mm including necessary accessories like bends, tees, PVC junction, square elbowas concealed conduit wiring with laminated top cover fixed on GIsunken boxes (thickness not less than 1.6 mm)for housing of switch ,socket etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLS insulated unsheathed stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly complete all as specified and directed. |
| 101 | All as perSrl item No.100.00 butforone 3 pin, 2 in 1, socket outlet 6 Amps on same board complete all as specified and directed. |
| 102 | All as per Srl item No.100.00 butforone 3 pin, 2 in 1, socket outlet 6 Amps on independent boardbut below the switch board of light points in the same vertical plane complete all as specified and directed. |
| 103 | All as per Srl item No 100.00 but for power socket 15/16 Amp with cable 2.5 sqmm for phase, 2.5 sqmm for neutral and earth complete all as specified and directed. |
| 104 | Supply and FixingSwitch piano, FLUSH TYPE, Single pole, One way, 6 Amp , 230 V AC circuit complete all specified and directed. |
| 105 | Supply and Fixing Switch piano, FLUSH TYPE, Single pole, One way, 16 Amp complete all as specified and as directed |
| 106 | Supply and Fixing Socket outlet, 2 in 1, 3 pin, 6 Amp complete all as specified and as directed |
| 107 | Supply and fixing Socket outlet, 2 in 1, 3 pin, 6 and 16 Amp, Flush Type complete all as specified and as directed |
| 108 | S&F Lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting completeall as specified and directed. |
| 109 | Supply and fixLED 12 W Inverter Bulb B22 CDL Lamp V2with 1200 Lumenens in normsl mode and around 350Lumens in power backup mode with charging time of (8 -10 ) hours & power backup of aroung 4 hours Class leading safety protection measures with overcharging protection, with deep discharge protection, with short circuit protection suitable size all asspecified and directed.Make:Havells Cat No LHLDDDEAIB5R012 or equivalent of Phillips /Wipro. |
| 110 | Supply and fixing LED lights fitting 1x 18W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 111 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed |
| 112 | S & FixDistribution board sheet metal enclosure Double Door, factory made,Single pole and neutral 12 way 240 Volt unit complete all as specified and directed. |
| 113 | S & FixDistribution board sheet metal enclosure Double Door, factory made,Single pole and neutral 4 way 240 Volt unit complete all as specified and directed. |
| 114 | S & Fixsingle pole and neutral enclosure with a two pn and earth plug and socket complete with one single pole MCB 20 amp complete all as specified and directed. |
| 115 | Supply and Fixing ceiling rose, surface bakelite, 65x50mm, two to three terminals, complete all as specified and as directed. |
| 116 | Supply and fixingofMCB SPN 5-32 Amps, 10 KA B curve, 230 Volt, 50 Hz complete including taking down unservicable all as specified and directed. |
| 117 | Supply and fixingofMCB SP 6-32Amps 10 KA, B curve, 230 Volt, 50 Hz complete including taking down unservicable all as specified and directed. |
| 118 | Supply and fixingin of Sub main wiring forPVC insulated single core mult stranded copper cableunsheathed FRLS cable 1100 V gradof size 2 x 4 sq. mm +1x 4sq. mm earth wireand drawn through PVC conduit ofsuitable size in clusing all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and as directed . |
| 119 | Supply and fixingin of Sub main wiring forPVC insulated single core mult stranded copper cableunsheathed FRLS cable 1100 V gradof size 2 x 6 sq. mm +1x 6sq. mm earth wireand drawn through PVC conduit ofsuitable size in clusing all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified and as directed . |
| 120 | Supply and fixing ceiling fans complete with blades, down rods, electronicregulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless(BLDC)direct current motor complete all as specified and as directed . |
| 121 | Supply and Fixing Exhaust/ ventilatingfan PVCtype 250mm size. 230 volt, 50 Hz single Phase with Louver for Exhaust/ ventilatingfan 250 mm size including making round suitable size smooth hole complete all as specified and directed. |
| 122 | Supply and fixingof Mirror light energy efficient luminarie withLED 10 Wattlinear & compact 10 W mirror light with decorative grey end caps, ploycarbonate body and ribbed opal diffuser. all accessories pre-wired and including connection up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed |
| 123 | M & L for Earthing complete with galvanized steel earth plate electrode 60x60cm x 6.0 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level connected to and including galvanised earth lead wire 4.0 mm dia,by means of nuts,bolts,checknuts and washers of galvanized iron including 15 mm bore GI pipe,medium grade up to 7.5 meters long all as shown in electrical plate No.3 of MES SSR part-I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber,precast RCC slab 50mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM,( weight not less than 4 Kg/Sqm), with cast iron frame, funnel with wire mesh,GI watering pipe 20 mm dia medium grade,test point and lugs complete all as specified and as directedNOTE:-(i) Items includes the cost of 7.5 metre length GI pipe and earth lead for protection of earth lead.Any variation in length shall be adjusted through deviation order.(ii) On testing, if the earth resistance is not obtained as per IS standard, earthing will be regenerated at no extra cost till the desired earth resistance is obtained. |
