|
| 1 | Excavation over areas not exc 1.5m deep in hard/ dense soil for foundation etc. and getting out, complete all as specified and directed by Engineer In Charge. |
| 2 | Removing and disposing off the excavated material/soil out side MD Land, complete all as specified and directed by Engineer In Charge.Note:- For payment purposes, quantity of excavation after deduction of the quantity of returning filling, shall only be payable under this item. |
| 3 | Material and Labour for Grubbing up tree trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and levelling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site, girth of tree Exc.30cm and n exc. 100cm complete all as specified and directed by Engineer In Charge. |
| 4 | Material and Labour for surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out In Hard/dense soil complete all as specified and directed by Engineer In Charge. |
| 5 | Excavating in trenches, by mechanical means(hydraulic excavator) n exc 1.5 m wide and n exc 1.5 m in depth; for footing, Plinth Beam & Dwarf Wall, etc. n exc 10 sq m on plan and getting out in Hard/ dense soil complete all as specified and directed by Engineer In Charge. |
| 6 | Excavating in trenches, by mechanical means(hydraulic excavator) exc 1.5 m wide and n exc 3.0 m in depth; for footing, Plinth Beam & Dwarf Wall, etc. n exc 10 sq m on plan and getting out in Hard/dense soil complete all as specified and directed by Engineer In Charge. |
| 7 | Material and Labour for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engineer In Charge. |
| 8 | Material and Labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed by Engineer In Charge. |
| 9 | Material and Labour for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed by Engineer In Charge. |
| 10 | Material and Labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engineer In Charge. |
| 11 | Material and Labour for cement concrete in foundations, filling and mass concrete 1:4:8 using 40 mm graded aggregate (For Foundation) complete all as specified and directed by Engineer In Charge. |
| 12 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Hard/dense soil complete all as specified and directed by Engineer In Charge. |
| 13 | Removing excavated material in Hard/dense Soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engineer In Charge. |
| 14 | Material and Labour forRCC- M-30 (Design Mix) using 20mm graded aggregate For Footing and plinth beams complete all as specified and directed by Engineer In Charge. |
| 15 | Material and Labour forRCC- M30 (Design Mix) using 20mm graded aggregate for Column complete all as specified and directed by Engineer In Charge. |
| 16 | Material and Labour forRCC- M30 (Design Mix) using 20mm graded aggregate for beams and lintels complete all as specified and directed by Engineer In Charge. |
| 17 | Material and Labour forRCC- M30 (Design Mix) using 20mm graded aggregatefor RCC Slab complete all as specified and directed by Engineer In Charge. |
| 18 | Material and Labour forRCC- M30 (Design Mix) using 20mm graded aggregatefor RCC parapet wall/drops/RCC Chajjas complete all as specified and directed by Engineer In Charge. |
| 19 | S & F TMT bars 10mm dia & over of Grade Fe 500 incl cutting, bending, binding & placing in position with binding wirefor footings Slab beams roof slab etc complete all as specified and directed by Engineer In Charge. |
| 20 | All as per item No 19 above but 5 to 10mm dia in stirrups, spacers & binders complete all as specified and directed by Engineer In Charge. |
| 21 | Material and Labour for form workfor rough finished surfaces of concrete measured flat for For Footing complete all as specified and directed by Engineer In Charge. |
| 22 | Material and Labour for form workfor rough finished surfaces of concrete measured flat for Column complete all as specified and directed by Engineer In Charge. |
| 23 | Material and Labour for use & waste Form workfor rough finished surfaces of concrete measured flat for Plinth Beam complete all as specified and directed by Engineer In Charge. |
| 24 | Material and Labour for use & waste Form workfor rough finished surfaces of concrete measured flat for RCCbeams sides and soffits complete all as specified and directed by Engineer In Charge. |
| 25 | Material and Labour for use & waste Form workfor rough finished surfaces of concrete measured flat for RCCSlab complete all as specified and directed by Engineer In Charge. |
| 26 | Material and Labour for use & waste Form workfor rough finished surfaces of concrete measured flat for RCCdrops/Chajjas complete all as specified and directed by Engineer In Charge. |
| 27 | Material and Labour for Pre-cast cement concrete block masonry with solid blocks Type C1 1:3:6, exc. 10 cm in width and setting in Cement mortar (1:6) mortar, complete all as specified and directed by Engineer In Charge. |
| 28 | Supply and fixingfactory made WPC solid door frames of size 65x100mm including fixing to walls using three numbers dash through bolt on each side as complete all as specified and directed by Engineer In Charge. |
| 29 | Supply and fixingfactory made single extruded WPC solid door shutters decorative type flush door of size 35mm complete all as specified and directed by Engineer In Charge. |
| 30 | Supply and fixing extruded aluminum alloy handles (150mm ) fabricated type anodised complete all as specified and directed by Engineer In Charge. |
| 31 | Supply and fixing hinges (150 mm)stainless steel medium weight complete all as specified and directed by Engineer In Charge. |
| 32 | Supply and fixing aluminum anodised barrel tower bolts (150 mm) of extruded section complete all as specified and directed by Engineer In Charge. |
| 33 | Supply and fixing 300 mmAluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type ) and fixing clips of sheet , cast , exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engineer In Charge. |
| 34 | S&F powder coated aluminium sections frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer In Charge. |
| 35 | Material and Labour for for Ready mix plaster 10mm thickonfaces of bricks or concrete surface includingincluding preparation of wall surfaces etc complete all as specified and directed by Engineer In Charge. |
| 36 | Material and Labour for for rendering 5mm thick in ready mix plaster on ceiling surface and finishing the surfaces even and smooth without using extra cement including scrapping down and preparation of ceiling surfaces to receive plaster, scaffolding as reqd etc, complete all as specified and directed by Engineer In Charge. |
| 37 | Material and Labour for for Ready mix polimer modified cement based plaster 15mm thick on new bricks or concrete surface including preparation of wall surfaces etc complete all as specified and directed by Engineer In Charge. |
| 38 | Material and Labour for applying two Coats Of Oil Bound Distemper Over One Coat Of Primer on Internal Wall complete all as specified and directed by Engineer In Charge. |
| 39 | Material and Labour for applyingtwo Coats Of Oil Bound Distemper Over One Coat Of Primer on ceiling complete all as specified and directed by Engineer In Charge. |
| 40 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additivesM @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer In Charge. |
| 41 | Material and Labour for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer In Charge. |
| 42 | Material and Labour for Screed bed or bedding layer of mortar CM(1:6) 15 mm thick for laying floor finishes complete all as specified and directed by Engineer In Charge. |
| 43 | Material and Labour for coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer In Charge. |
| 44 | Material and Labour for Coloured Glazed ceramic tiles in vertical surface 350 x 250 mmx 7 mm / 450 x350x 7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer In Charge. |
| 45 | Material and Labour for machine cut kota stone slab flooring, 20mm thick over cement screed bas laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finish polishing all as specified and directed complete all as specified and directed by Engineer In Charge. |
| 46 | All as per items No45 above but asin skirting complete all as specified and directed by Engineer In Charge. |
| 47 | Material and Labour for granite work(table rubbed and polished) in jambs, steps, window cills, platforms and like in cement mortar 1:4 including pointing in white cemnt using marble dust with admixture of pigment to match with shade of granite 20mm thick,all as specified and directed complete all as specified and directed by Engineer In Charge. |
| 48 | Material and Labour for 75mm thick Plinth Protection PCC (1:3:6) using 20mm graded aggregate (0.75 m wide) complete all as specified and directed by Engineer In Charge. |
| 49 | Material and Labour for 3mm APP based polymeric membrane minimum weighing 3.5 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torched application complete and finally finished as per manufacturers instructions complete all as specified and directed by Engineer In Charge. |
| 50 | Material and Labour for screed bed or bedding layer of mortar CM(1:3) 10 mm thickcomplete all as specified and directed by Engineer In Charge. |
| 51 | Supply only Water Proofing compound complete all as specified and directed by Engineer In Charge. |
| 52 | Supply and fixingaluminum anodised grill DG- 202 ( 10 mm x 5.2mm ) of Deco grill or equivalent fixed with \"F\" section size not less than 20.60 x 15.20 x 1.5mm thick of approved make complete all as specified and directed by Engineer In Charge.Note : (i)Make shall be of Decogrille of M/s Associated Groups or equivalent as approved by the GE.(ii) Minimum thickness of anodizing shall be 15 microns. |
| 53 | Supply only 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etccomplete all as specified and directed by Engineer In Charge. |
| 54 | Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed by Engineer In Charge. |
| 55 | Supply and fixing inGodrej night latch 4 lever for entrance door with fittings complete all as specified and directed by Engineer In Charge. |
| 56 | Supply and fixing brass chromium plated towel rail 20mm dia \"D\" type 600mm long between flanges, Cat No BA -01of with and including chromium plated brass screws etc complete all as specified and directed by Engineer In Charge. |
| 57 | Supply and fixing20mm dia fancy type chromium platedcurtain rod brackets complete all as specified and directed by Engineer In Charge. |
| 58 | Supply and fixing CI floor trap 75mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & taking down old trap complete all as specified and directed by Engineer In Charge. |
| 59 | Supply and fixing CI floor trap 100mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & including taking down old trap complete all as specified and directed by Engineer In Charge. |
| 60 | Supply and fixingwash hand basin, vitreous china white of size550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar tapschromium plated fancy type etc complete all as specified and directed by Engineer In Charge. |
| 61 | Supply and fixing for CP concealed stop cock 15mm borefancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer In Charge. |
| 62 | Supply and fixingCP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer In Charge. |
| 63 | Supply and fixingCP bib tap 15mm bore fancy type with crutch or butterfly handle, screwedfor iron pipe or for unions and fixed complete all as specified and directed by Engineer In Charge. |
| 64 | Supply and fixingCP pillar taps15mm bore., cast copper alloy, chromium plated fancy type complete all as specified and directed by Engineer In Charge. |
| 65 | Material and Labour for in repairwaste fitting of 32 mm borebrass, chromium plated for glazed ware wash basin etc complete all as specified and directed by Engineer In Charge. |
| 66 | S&F waste pipe for WHB/ sink32mm bore fixed to wash hand basin/sinks coupling length pipe 0.90 mtrs each complete all as specified and directed by Engineer In Charge. |
| 67 | S&Fin repair 15mm size PVC connection with PTMT nuts 450mm length complete all as specified and directed by Engineer In Charge. |
| 68 | Supply and fixing stainless steel grating in ground shape 100mm dia complete all as specified and directed by Engineer In Charge. |
| 69 | Supply and fixing low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls or laid in floors etc complete all as specified and directed by Engineer In Charge. |
| 70 | Supply and fixing soap dish Cat No BA -25of Prayag polymers Pvt Ltd or equivalent complete all as specified and directed by Engineer In Charge. |
| 71 | Supply and fixing 15mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings complete all as specified and directed by Engineer In Charge. |
| 72 | All as per item No 71above but 20 mm bore complete all as specified and directed by Engineer In Charge. |
| 73 | Supply and fixing for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore complete all as specified and directed by Engineer In Charge. |
| 74 | Supply and fixing Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1998 grade St.-240 complete all as specified and directed by Engineer In Charge. |
| 75 | Supply and fixingrolled mild steel in roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam,tee, angle, channel or flat sections)incl distance pieces, cleats, etc conforming to grade Fe-410W-(Gde E-250 Quality A) complete all as specified and directed by Engineer In Charge. |
| 76 | Supply and fixing for mild steel Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer In Charge. |
| 77 | Supply and fixing MS bands, straps, supports or stays for rainwater, ventilating pipes, including bolts if reqd, hooks(stay), hook and pintle hinges, large hasp and staples, clamps, hold fasts, wall ties, plain angle cleats for securing purlins to wood trusses or rafters and similar small articles confirming to Fe-290 Gde E-165 complete all as specified and directed by Engineer In Charge. |
| 78 | Supply and fixing Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer In Charge. |
| 79 | Supply and fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer In Charge. |
| 80 | Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer In Charge. |
| 81 | Supply and fixing PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm dia complete all as specified and directed by Engineer In Charge. |
| 82 | Material and Labour for synthetic Writing board with green or white colour surface fixed to walls including raised wooden boarders all as specified of size 4mx1.80m complete all as specified and directed by Engineer In Charge. |
| 83 | Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in soft loose soil complete all as specified and directed by Engineer In Charge. |
| 84 | Material and Labour for 75 mm thick Cement concrete type D-2 1:4:8 (40mm graded aggregate) as in Sub-Floors, Sub-Bases, Floors and pavings, etc all as specified and as directed complete all as specified and directed by Engineer In Charge. |
| 85 | Material and Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces using CM 1:4, finished the surface even and smooth complete all as specified and directed by Engineer In Charge. |
| 86 | Material and Labour for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade mixed with greay cement and pigment complete all as specified and directed by Engineer In Charge. |
| 87 | Material and Labour for sand filling under floors or in foundations incl watering and consolidation complete all as specifed and directed complete all as specified and directed by Engineer In Charge. |
| 88 | Material and Labour for Reinforced concrete pipe class NP 2 laid and jointed complete with collars of 300 dia bore complete all as specified and directed by Engineer In Charge. |
| 89 | Material and Labour for concrete bed to drain pipeof 300 dia bore using type C2 (1:3:6) complete all as specified and directed by Engineer In Charge. |
| 90 | Material and Labour for point wiring using approved colour coding as per IS ,with multistranded copper conductor 1.5 Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit with allfittings, accessories, PVC junction boxes etc.with and includingconcealed PVC switch, socket, regulator mounting, SAC-WHT-JBX1, 86 Size,( HSN 85365020)junction box Make Jaquar or equivalent and also including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor along with wiring and connecting to earth dolly all as specified and as directed for the following (a) One light point/ exhaust fan pointcontrolled by one, one way switch 6 Amps complete all as specified and as directed |
| 91 | (b) Two light point controlled by one, one way switch 6 Amps on the same switch circuit complete all as specified and directed by Engineer In Charge. |
| 92 | (c) One5 pin socket outlet plug point, 16 Amps, controlledby one, switchon same boardcomplete all as specified and directed by Engineer In Charge. |
| 93 | (d) One two way light point controlled by two nos. two way 6A switches complete all as specified and directed by Engineer In Charge. |
| 94 | (e) Onebell pointcontrolled by one, one way switch 6 Amps complete all as specified and directed by Engineer In Charge. |
| 95 | (f)One ceiling fan point & regulator controlled by one, one way switch 6 Amps complete all as specified and directed by Engineer In Charge. |
| 96 | Description all as per Item No 90 here-in before but using 2.5 Sqmm singlecore copper conductor FRLS cable of multistranded PVC insulated unsheathed 1100 Volts grade for one 6 pin socket outlet plug point, 6 Amps independentincluding necessary running of 2.5 Sqmm PVC insulatedmultistranded copper conductor single core FRLS cable as earth continuity conductor along with wiring and connecting to earth dolly all as specified and as directed. Note for Item 90 to 96 (i) Cutting chases for conduits and sinking\"s for PVC switch boxes and making good to walls in cement mortar 1:3 to match with existing surfaces shall be carried out by the contractor without any extra cost from the department. (i) Cutting chases for conduits and sinking\"s for PVC switch boxes and making good to walls in cement mortar 1:3 to match with existing surfaces shall be carried out by the contractor without any extra cost from the department complete all as specified and directed by Engineer In Charge. |
| 97 | Supply and fixing High strength, flame retardant,fade-resistant Poly Carbonate, Easy on-off, White 16AX Three gang one way switch and face plate in one complete with Terminal screw in ready for wiring Make Jaquar Cat No SWG-WHT-PC16A3G01 or Equivalent in Legrand |
| 98 | Supply and fixing High strength, flame retardant,fade-resistant Poly Carbonate, Easy on-off, White 16AX Two gang two way switch and face plate in one complete with Terminal screw in ready for wiring complete all as specified and directed by Engineer In Charge. Make Jaquar Cat No SWG-WHT-PC16A2G02 or Equivalent in Legrand |
| 99 | Supply and fixing High strength, flame retardant,fade-resistant Poly Carbonate, Easy on-off, White 16A Door bell one way switch and face plate in one complete with Terminal screw in ready for wiring complete all as specified and directed by Engineer In Charge. Make Jaquar Cat No SWG-WHT-PC16A1GB1 or Equivalent in Legrand |
| 100 | Supply and fixing High strength, flame retardant,fade-resistant Poly Carbonate, Easy on-off, White 1 Gang 16A switched socket with indicator and face plate in one complete with Terminal screw in ready for wiring complete all as specified and directed by Engineer In Charge. Make Jaquar Cat No SKG-WHT-PC16ASC1GS1 or Equivalent in Legrand |
| 101 | Supply and fixing High strength, flame retardant,fade-resistant Poly Carbonate, Easy on-off, White 1 Gang Fan speed controller switchin one complete with Terminal screw in ready for wiring complete all as specified and directed by Engineer In Charge. Make Jaquar Cat No- SWG-WHT-PC1ARFSS or Equivalent in Legrand |
| 102 | M & L Ceiling rose, 3 terminal /PVC/ polycarbonate, isolated body complete all as specified and directed by Engineer In Charge. |
| 103 | Supply and fixing electric Buzzer, Ding Dongbell suitable for operation on AC. 230 volts, single pole complete all as specified and directed by Engineer In Charge. |
| 104 | Supply and fixing wall/ surface mounted, LED- 35W ± 10% watt Power consumption, AL. Extruded Housing, 230 VAC, 50Hz batten fitting complete with standard warranty of manufacturer from date of purchase/ installation complete all as specified and directed by Engineer In Charge.Make Jaquar Cat No- HBT-WHT-LKBU4KVS35XC or equivalent in Philips,crompton |
| 105 | Supply and fixing energy saving, Full Glow LED Surface Light luminaire complete with Motion Sensor, Power consumption 15 Watt, Round Shape, single Phase 230 Volt. fitting and standard warranty of manufacturer from date of purchase/ installationcomplete all as specified and directed by Engineer In Charge.Make Philiphs ( Product SKU : 929003671501) or equivalent in Jaquar, Crompton. |
| 106 | Supply and fix for energy saving new generation environmentalfriendly long life versatile pressure die aluminium IP-66 for security light fitting luminaire of capacity 30 watt with high power LEDs as light source and electronic driver , necessary mounting arrangements and provision of 1.0 Sqmm 3 core copper conductor cable multistranded fromceiling rose to light fitting including1.5 metres long GI pipe medium grade bracket of suitable size & shape to light fitting mounting dia, secured and fixed with clamps made out of MS flat iron ofsize 25mm x 5mm, nuts, bolts etc , as approved, complete all as specified and directed by Engineer In Charge.Make- Jaquar Cat No LPCRSRT30WXW or equivalent in Philips, Havells |
| 107 | Supply and fixing ceiling fansworking on single phaseinput voltage 140-285 , Sweep- 1200 mm, Power 32 W,345 RPM ,with232 Air delivery CMM (m3 /min), complete with compact BLDC Motor,blades, down rods, electronic regulator and accessories, including making connections with provision of flexible wire 23 /0.0076 twin core copper conductor from ceiling rose/connector to fan complete all as specified and directed by Engineer In Charge. Make- Atomberg (Renesa Alpha) or Equivalent in Havells Model -Trinity |
| 108 | M & L for submain wiring with approved colour coding as per IS with two single core PVC insulated FRLS multistranded copper conductor cable of size 4 Sqmm nominal area and drawing intoconcealedPVC non metallic rigid heavy duty conduit and its accessories (ISI marked) of suitable size including PVC insulated multistranded copper conductor 4 Sqmm (nominal area) single core FRLS cable as earth continuity conductor along with submain wiring and connecting to earth dolly complete all as specified and directed by Engineer In Charge. Note- Three run of 4 Sqmm cable and one run of PVC conduit will be measured as one unit complete all as specified and as directed |
| 109 | Supply and fixing 25 A Heavy Duty MCB COMBO WITH 4M(Metal) Power box, with 6 A/16 A Heavy Duty Socket with Shutter and one single pole 25 A SP C MINI MCBincluding white cover plate complete all as specified and directed by Engineer In Charge. |
| 110 | Supply and Fixing sheet metal enclosure suitable for Flush Mounting and Surface Mounting, MCB DB with 250 Amps rated bus bar for each phase, Fully insulated & shrouded 2 Neutral bars, 2Earthbar and Cable ties for Cable management, &With provision for DPX³ 250 MCCB as incomer and SP/TP MCB\"s as outgoing, 415Volts, IP 43 - #IK 09 with metal double door & magnetic locking system includinginserting the DBs in wall by cutting the brick/ stone masonary etc and making good of disturbed surface in cement mortar to match the existing surface &colour to wall complete all as specified and directed by Engineer In Charge. (a) VTPN 4 Way. (Make Legrand Cat No - 5077 58 orequivalent.) |
| 111 | Supply and fixing DPX³ 160 MCCB with O/L & S/Cthermal magnetic protection unit, 25 KA breaking Capacity, 4 Pole , 63 Amps complete all as specified and directed by Engineer In Charge. Make Legrand Cat No 4200 53 or Equivalent in L&T |
| 112 | Supply and fixing amp rating 240V, 10KA \"C\" curve, IP 20 protected terminals, miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. (a) SP 5 To 32 AMP complete all as specified and directed by Engineer In Charge. |
| 113 | M & L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.0 mm thick,buried vertically in ground (Earth pit not less than 2.25 metres deep below normal ground level and top edge of the plate not less than 1.5 m below ground level),connected to and including galvnised steel earthing lead wire 4 mm dia, by means of bolts, nuts, check nuts and washers etc;GI pipe15 mm dia medium grade pipe for protection of G.I earth lead wire, both to be provided to the extent of 7.5 metres, all as shown on electrical plate No 3 of MES SSR-2009 Part-I, other end connected to electrical main switch board (inside the bldg) GI protection pipe buried in ground, laid under floors/plinths or fixed on walls or concealed in walls etc; with provision of mixture of charcoal dust & common salt packed upto minimum 150 mm all around the earth plate , including PCC 1: 2 : 4 type B-1 earth pit with M.S angle iron frame, cast iron cover with locking arrangement, with G.I 20 mm dia medium grade pipe and M.S funnel with wire mesh for watering arrangement, including necessary excavation and earth work in any type of strata & testing on completion complete all as specified and directed by Engineer In Charge. |
| 114 | Excavation in Trenches not exc 1.50 Metre wide and not exc 1.50 Metre depth for laying of UG Cable etc and getting out in Soft/Loose Soil, complete all as specified and directed by Engineer In Charge. |
| 115 | Returning, Filling in including Spreading, Leveling, Watering and Well Ramming in layers not exc. 25 Cm thick in Soils, complete all as specified and directed by Engineer In Charge. |
| 116 | Removing Surplus excavatedSoil to a distance not exc 50.00 Metre away and depositing where directed at a level not exc 1.50 Metre above the Starting Point, complete all as specified and directed by Engineer In Charge. |
| 117 | Material and labour forcable route marker made of Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregrate)with solid blocks, exc. 10 cm in width and settingin cement concrete mortar 1:6, includingembosing DANGER/ LT CABLE / MESon cable route marker and properly painting with approved colour,size of cable route marker 900x300x100mm completeburied in ground for a depth of 45 cm & necessary earth work complete all as specified and directed by Engineer In Charge. |
| 118 | Supply and layingHDPE Pipe PN 10 Size 40mm laid in trenches along with accessories such as couplerfor electrical applications as in cable protection pipe from physical damagecomplete all as specified and directed by Engineer In Charge. |
| 119 | Supply and laying across road crossing reinforced concrete pipes, class NP2, laid and jointed complete with collars of size 150 mm complete all as specified and directed by Engineer In Charge. |
| 120 | Material and Labour Soling (or sub base) 150 mm spread thickness with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber complete all as specified and directed by Engineer In Charge. |
| 121 | M&L Cement Concrete Type B2-1:2:4 (40mm graded aggregate) as in Foundation filling and mass concretefor grounting of panel and making good disturbed road surfaces including necessary Formwork (as/if required) complete all as specified and directed by Engineer In Charge. |
| 122 | Supply & laying LTAluminium Conductor Power Cables, Stranded Conductor, XLPE Insulated, Cores Laid Up, PVC Innersheathed, Armoured galvanised steel strip,Extruded PVC Type ST2 Outer Sheathed, 1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments. cross-sectional area 25 Sqmm 4 Core, passing in HDPE Pipe laid in trenches/ fixing on surface of Wall in cable tray securing with GI Cable clampsincluding Brass Cable Glands at termination end points Mild Steel Flat Iron Clamps of adequate size, etc. and Testing laid in trenches complete all as specified and directed by Engineer In Charge. |
| 123 | Supply and fixing DPX³ 160 MCCB with O/L & S/Cthermal magnetic protection unit, 25 KA breaking Capacity, 4 Pole , 63 Amps laid in trenches complete all as specified and directed by Engineer In Charge. Make Legrand Cat No 4200 53 or Equivalent in L&T |
| 124 | Supply and fixing Unplasticised PVC (UPVC) pipes of pressure rating 10 kgf / cm2 with all fitting and fixed complete to walls with clips, wall hooks, wooden plugs, and ceilings or laid in floorsbore of pipe 25 mm complete all as specified and directed by Engineer In Charge. |
| 125 | Supply and fixing Unplasticised PVC (UPVC) pipes of pressure rating 10 kgf / cm2 with all fittings and fixed complete, together with Pipe,laid in trenches bore of pipe 32 mmcomplete all as specified and directed by Engineer In Charge. |
| 126 | All As per item No 125 above but bore of pipe 40 mm |
| 127 | S & F UPVC Ball valve 25mm Outer dia heavy weightas per pre requirement of the site with handle screwed both ends for UPVC Pipes or for unions complete all as specified and directed by Engineer In Charge. |
| 128 | S & F UPVC Ball valve 40mm Outer dia heavy weightas per pre requirement of the site with handle screwed both ends for UPVC Pipes or for unions complete all as specified and directed by Engineer In Charge. |
| 129 | Cutting existing steel tubing for alterations or additions (Each cut measured) for Bore of Pipe 40mm or 50mm without taking down complete all as specified and directed by Engineer In Charge. |
| 130 | Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) for Bore of Pipe 40mm or 50mm without taking down complete all as specified and directed by Engineer In Charge. |
| 131 | Deduct Credit for Demolished/ Dismantled material Rs. (-) 0.00 (Minus) as listed in Schedule of Credit.Note 1:- Tenderers will not quote against this item being a tentative amount to be considered to arrive at the \"Contract Sum\"Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items. |
