Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 12-01-2026 | Corrigendum Date | Date | 27-01-2026 |
| Sl. No. | Item Description |
| 1 | Schedule \"A\" Part-I (B/R itmes)Demolition of cement concrete (un–reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete, all as specified and as directed by the Engineer-in-Charge. |
| 2 | Providing and injecting emulsion for post construction anti termite treatment using chemical chloropyriphos 20EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 concentrate along the external wall of buildingbelow concrete or masonry apron using chemical emulsion @ 2.25 litre per linear metre including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 Cement 2 Coarse sand) in apron etc,. ,complete all as specified and directed. |
| 3 | Providing and injecting chemical emulsion for post construction anti termite treatment using chemical chloropyriphos 20EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 of soil under existing floorsusing chemical emulsion @ 1 Litre per hole 300mm apart including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 Cement & 2 Coarse sand) to match the existing floor and making good the disturbed sufaces to match with the existing surface, ,complete all as specified and directed. |
| 4 | Providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by usingchemical chloropyriphos 20EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 emulsion in oil or kerosene based solution@ 0.5 litre per hole by drilling 6mm dia holes at a downward angle of45 degree @ 150mm centre to centre and sealing the same and making good the disturbed sufaces to match with the existing surface, ,complete all as specified and directed. |
| 5 | Demolition of cement concrete (unreinforced) of any descriptionand in any position including any type of sunken treatment , roof treatment, PCC padding, roof PCC tiles,lime concrete etc. , ,complete all as specified and directed.Note: All Demolished material / debries will be taken by the contractor out side of thecantonment without any extra cost to the govt,contractor should quote his rate Keeping this aspect in mind. |
| 6 | Material & Labour cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) , ,complete all as specified and directed. |
| 7 | Material & Labour PCC (1:3:6) type C1 using 20 mm graded stone aggregate as inmass concrete over roof as in padding incl cement slurry @ 3Kg/Per sqm over old RCCsurface, surfacefinished even & smooth without using extra cement. all as specified and directed by Engr-in- charge. |
| 8 | Material & Labour ,15 mm thick plaster in cement mortar (1:4) over concrete surfaces of roofs finished even and smooth with WPC @ 3% by weight of cement ( WPC will be measured paid for seperately) as in roof treatment workall as specified and directed . |
| 9 | Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at theside and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture\"s instructions. The vital physical and chemical parameters of the membrane shell be under :–(i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms(ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147)(iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only, complete, all as specified and as directed.(iv)The work shall be carriout at a height upto 12 metre. |
| 10 | M&L cement concrete tiles 30 cm x 30cm x 20 mm thick, machine pressed laid on screed bed and joints groutedand pointed flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar 1:6 , complete, all as specified and as directed. |
| 11 | M&L for providing cement concrete 1:2:4 Type B1 using 20mm graded crushed stone aggregate as in roof kerbs or mud stops, padding, rounded or chamfered on edges including from work where ever required , complete, all as specified and as directed. |
| 12 | Dismentling of brick work built in cement mortar or cement lime mortar including all quoins, arches,pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles , ,complete all as specified and directed. |
| 13 | Material & Labourbrick work with sub class \"B\" old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 , ,complete all as specified and directed. |
| 14 | Material & Labour brick work with sub class -B bricks, in half brick thick walls, built in cement moratr 1:4 straight or curved on plan to any radius , ,complete all as specified and directed. |
| 15 | Supply only integral water proofingcompound, ,complete all as specified and directed. |
| 16 | Dismantling floor,hearth or wall tilling including cement mortar bedding (but not backing ),removing serviceable tiles to store and rubbish off premises , ,complete all as specified and directed. |
| 17 | Material & Labour providing 75 mm thick cement concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregates as in plinth protection, laid in alternatebays (not exc 2 Sqm each )and finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work, complete, all as specified and as directed. |
| 18 | Material & Labour for 25 mm thick Cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in sub base floors, surface fair finished and even and rough to receive floor finishes , complete, all as specified and directed. |
| 19 | Material and labour for 8 to 10mm thickheavy duty (digital) vitrified coloured paver tiles of size 300mm x 300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) , complete all as specified and as directed Make: Endura of Johnson or Durastone of Somany or equivalent make given in App ‘B’ |
| 20 | Material & LabourNon Skid coloured ceramic tiles joint freepremium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding15mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 21 | Material & LabourNon Skid coloured ceramic tiles premium/1st quality of same description as of floor tiles in serial item No 20abovebut 100mmto 200mm heightas in skirting, set and jointed in neat cement slurry and pointed in white or colouredcement mixed with pigmentto match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4complete all as specified and as directed. |
| 22 | Material & Labour for glazed ceramic coloured tiles 300x600x7 to 8mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coatin cement mortar (1 :4) complete all as specified and as directed. |
| 23 | Dismantling stone slab of any description or thickness laid, bedded and pointedin any motar in floors etc , ,complete all as specified and directed. |
| 24 | Material & Labour for Granite (of any type)slab 18-20 mm thick machine cut ,bedded and jointed with gray cement slurry and pointed with white cement as in floors/ cooking plateform, with admixiture of pigment to match the shade of granite stone including grindingand polishing complete over and including20 mm thick screed bed in CM 1:6 , ,complete all as specified and directed. |
| 25 | Material & Labour for Granite (of any type)slab 18-20 mm thick machine cut , jointed with gray cement slurry and pointed with white cement as in vertical surfaces / dado / skirtingwith admixiture of pigment to match the shade of granite stone indluding grindingand polishing complete over and including10 mm thick backing coat in CM 1:4 , ,complete all as specified and directed. |
| 26 | Material & Labour rounding to edges of stone slabboth edge such as in steps, cooking plateformand other similar situtaions withgrinder, ,complete all as specified and directed. |
| 27 | Material & Labour machine cut kota stone slab flooring 18 to 22 mm thick in floor/landing/treads of stairs,set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 , ,complete all as specified and directed. |
| 28 | Material & Labour machine cut kota stone slab flooring 18 to 22 mm thickin skirting , set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 10 mm thick renderingin CM 1:4 , ,complete all as specified and directed. |
| 29 | Material & Labour machine cut green marble stone slab flooring 18 to 22 mm thickin floor, window cills,set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishingover and including 15 mm thick screed bed in CM 1:6 , ,complete all as specified and directed. |
| 30 | Material & Labour machine cut green marble stone slab 18 to 22 mm thickin skirting , set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick renderingin CM 1:4 , ,complete all as specified and directed. |
| 31 | Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for, ,complete all as specified and directed.(Reinforced cut to facilated dismentling) |
| 32 | Material & Labour for Reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the likedack slab , ,complete all as specified and directed. |
| 33 | Material & Labour reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, graded stone aggregate as inchajjas,Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels,balustrade, and the like complete all as specified and directed by engineer in charge . |
| 34 | Material & Labour formwork to chajjas, fins, louvres, facias including edgesfor rough finished surfaces of concrete flats , ,complete all as specified and directed. |
| 35 | Material & Labour formwork to soffits ofsuspended slabs such roof slab, floor slabs, landings and similar work not exceeding 20 centimetre thick (horizontal or sloping) flat for rough finished surfaces of concrete , ,complete all as specified and directed. |
| 36 | Material & Labour formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofsand sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide, for roughed finished surface of concrete , ,complete all as specified and directed. |
| 37 | Material & LabourTMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia , ,complete all as specified and directed. |
| 38 | Taking down chowkats or frames with shutter areanot exceeding 1.50 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , ,complete all as specified and directed. |
| 39 | Taking down chowkats or frames with shutter area exceeding 1.50 Square metre andnot exceeding 4.00 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , ,complete all as specified and directed. |
| 40 | Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site , ,complete all as specified and directed. |
| 41 | Cutting holes in brick walls built in cementmortar exceeeding half brick thick and not exceeding one brick thick wall for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)as required , ,complete all as specified and directed. |
| 42 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58–60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant , ,complete all as specified and directed. |
| 43 | Supply and fixing offactory made solid PVC moulded door shutters with particle board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge. |
| 44 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/chowkhat of size 65mm x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast of required dia and length complete all as specified and directed.NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.(ii) Material manufacture test certificate should be provided before execution of work |
| 45 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded ( Jointless ) door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing withfull body threaded star headed counter sunk S.S screws, completeall as per specification & drawing, complete all as specified and directed. |
| 46 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) gauzed decorative type plain ( Jointless ) door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixingall as per specification & drawing complete all as specified and directed |
| 47 | Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed and gauged skeleton shutterfabricated fromfollowing sections :-(a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leafof T – section20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf .(c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mmmade from 1.25 mm thickMS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i)Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii)Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.iii) MS tower bolt stove enamelled150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf (vi)Pintal hinges 12 x 75 mm- 2 Nos each leaf (vii) 10mm square Guard bar @ 10 cm c/c welded to frame .(viii) Two coat of Synthetic enamel paint over one coat ofred oxide primer.(ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter ofwindow with flat iron 15 x 03 mm with steel screws .(x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5sqm in each pane fixed in glass shutter of window.(xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit.(ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above.(iii) The window upto1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable.The window more than 1.00 metrewidth shall have two openable leaves onboth outer sidefor gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type. |
| 48 | Supply and fixing box type using ERW hollow \"P\" section ventilators fixed type with glazing barincluding MS grills of square bar 10mm dia @ 100 c/c complete with glazing bars dovetailed or welded, including two coat of synthetic enamel ordinary tint paint over a coat of red oxide primer, complete all as specified and as directed by Engr-in-charge. |
| 49 | Material & Labour sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane, ,complete all as specified and directed. |
| 50 | Supply and fixing mild steel works in bands, straps, supports, stays, bolts, hooks, hold fasts etc, similar articles conforming toFe-290.Gde-E-165, ,complete all as specified and directed. |
| 51 | Supply and fixing mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet (all as per godrej pattern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured), complete all as specified and as directed by the Engineer–in–Charge. |
| 52 | Resecuring or easing & adjusting after taking down shutters of any description area exc 1 sqm and not exceeding 2 sqm each andrefixing in the same opening , complete all as specified and as directed by Engr-in-charge. |
| 53 | Supplyand fixingstainless steel wire cloths0.36 mm nominal dia of wire and averagewidth of aperature 1.40 mm and fixed with stainless steelwire staple, complete all as specified and as directed by Engr-in-charge. |
| 54 | Supply and fixing 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pine including screwing or welding to MS / PVC frame ( as required ), complete all as specified and directed by Engr-in-charge |
| 55 | Supply and fixing 150 mm long aluminium handle cast type anodised, complete all as specified and as directed by Engr-in-charge. |
| 56 | Material and labour for 2nd class hard wood Small fitting such a brackets of any type ,latch and hinge block , shaped door and window stops and the like including all necessary labours articles not exceeding 200 Cu cm each including 50mm long mild steel cold rolled medium weight but hinge, complete all as specified and as directed by Engr-in-charge. |
| 57 | Supply and fixing 150 mm long aluminium anodised barrel tower boltsof extruded section and fixed ,complete all as specified and as directed by Engr-in-charge. |
| 58 | Supply and fixing 200 mm long aluminium anodised barrel tower boltsof extruded section and fixed ,complete all as specified and as directed by Engr-in-charge. |
| 59 | Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter ,complete all as specified and as directed by Engr-in-charge. |
| 60 | Material & Labour galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floorsas in repair, ,complete all as specified and directed. |
| 61 | Material & Labour galvanised iron tubing 20mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floorsas in repair, ,complete all as specified and directed. |
| 62 | Cuttingchases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth, ,complete all as specified and directed. |
| 63 | Supply and fixing 600mmx450mm bevelled edge mirror 5mm thick of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers,as in repair , ,complete all as specified and directed. |
| 64 | Supply and fixing in repair Vitreous china orissa pan squatting pattern 580 X 440mm with integeral foot rests includingP or S trapandincluding PVClow level flushing cistern 10 ltrs capacity and Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, ,complete all as specified and directed.Note : The cost of traps , flushing cistern and PVC flush pipes are included in this item. |
| 65 | Supply and fixingvitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing ofwaste fitting etc as in repair , ,complete all as specified and directed. |
| 66 | Supply and fixingsinks with drainage board made out of stainless steel 1mm thick sheet for kitchenwith plugs, waste pipe, brass chromium plated coupling including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mmwith bowl size 410mm x 330mm x 160mmas in repaircomplete all as specified and as directed. |
| 67 | Supply and fixing as in repairfancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe , ,complete all as specified and directed. |
| 68 | Supply and fixingas in repair15mm bore cast copper alloy chromium plated angular stop valveswith capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions , ,complete all as specified and directed. |
| 69 | Supply and fixing as in repair brass chromium plated shower rose 125mm size swivel type with arm of standard size as per site , ,complete all as specified and directed. |
| 70 | Supply and fixing 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, scrwed both ends for iron pipe or for unions as in repair , ,complete all as specified and directed. |
| 71 | Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body,wall flanges and capstan head,screwed down,screwed for iron pipe or for brass ferrule and fixed , ,complete all as specified and directed. |
| 72 | Supply and fixingPVC connections 15 mm diawith PTMT nuts of length 450 mm, as in repair , ,complete all as specified and directed. |
| 73 | Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia,60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge. |
| 74 | Material and labour for Stainless steel plate rack of size 31\" x 30\" x 10\" of load capacity not less than 30 kg including fixing with stainless stell screws including taking down of old plate rack of any description, complete all as specified and as directed by Engr-in-charge. |
| 75 | Supply and fixing in repairStainless steel ( SS 202 grade ) Curtain rod25 mm dia 0.80 mm wall thickness, mild steel, chromium platedincluding ornamental typesupporitng and end brackets as per sample, complete all as specified and as directed by Engr-in-charge. |
| 76 | Supply and fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 mm wide with chromiun plated brackets guard and railing 60 cm long as in reapir complete all as specified and as direced by the Engineer–in–charge. |
| 77 | Supply and fixingas in repair 100mm bore PVC (SWR) floor trap, plain with chromium plated grating including jointing with solvent cement, complete all as specified and as directed by Engr-in-charge. |
| 78 | Supply and fixing in repairbrass CP Soap Dish of size 100mmx100mm as approved Design, complete all as specified and directed by Engr in Charge . |
| 79 | Supply and fixing as in repair, water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including dismantling of water tanks and removing from site all as specified in SSR Part–I, complete all as specified and as directed by Engr-in-charge.Note : - The colour of tanks shall be white colour . |
| 80 | Cutting into existing manholes for connecting new drains, and making good to pipe and rendering, cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 100 mm dia,complete all as specified and as directed by Engr-in-charge. |
| 81 | Schedule \"A\" Part-II (E/M itmes)Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etccomplete all as specified and as directed. |
| 82 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly(boxesshall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally) including provision of new covered plate over sunken box for housing themodular switches , modular socket outlets,modularfan regulators etc.for one light/fan/exhaust fan/bell point controlledby one way switch,complete all as specified and as directed. Note :-a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid forseparately . |
| 83 | Description all as per serial item No.82 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board,complete all as specified and as directed. |
| 84 | Description all as per serial item No.82 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board,complete all as specified and as directed. |
| 85 | Material & Labour for concealed point wiring complete with 2.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathedcable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 2.50 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for :-Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted. |
| 86 | Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 voltscomplete all as specified and as directed. |
| 87 | Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 voltscomplete all as specified and as directed. |
| 88 | Supply and fixing of modular socket outlet2/3 pin combined,6 Amp, one way, two module, 230 voltscomplete all as specified and as directed. |
| 89 | Supply and fixing ofmodular socket outlet3/3 pin combined, (6pin), 6 and 16 Amps, one way, two module, 230 voltscomplete all as specified and as directed. |
| 90 | Supplyand fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed. |
| 91 | Supply and fixing in repair calling bell ding dong 230 volt, complete all as specified and as directed. |
| 92 | Supply and fixing ceiling rose surface type 2/3 terminalpolycarbonate, isolated body complete all as specified and as directed. |
| 93 | Supplyand fixingas in repairelectronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed. |
| 94 | Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed. |
| 95 | Supply and fixing in repairLED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic drivercool/warm typeindustrial model complete,connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed . Cat part No. LUMILINE+ BS20WLED865SPCSS of make Havells or equivalent in make given in Appx \"B\". |
| 96 | Supply and fixing in repair,LED batten fitting 10-12 watts, 2 feet, aluminium housing with electronic drivercool/warm typeindustrial model complete,connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed . Cat part No. LUMILINE+ BS10WLED865SPCSS of make Havells or equivalent in make given in Appx \"B\". |
| 97 | Supply and fixing in repair, LED surface mounted bulk head luminaries, 8-10 watts, with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed . Cat part No. HEXAFT10WLED857SSYMBOPC of make Havells or equivalent in make given in Appx \"B\". |
| 98 | Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 35 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed .Cat part No.ENDCITYLIT PLAT + SL35WLED757SASYBOPCWOSPD of make Havells or equivalentin make given in Appx \"B\". |
| 99 | Supply and laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and includingPVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 100 | Supply and laying as in repair sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium gradeISI marked of adequate size for housing the wires, complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 101 | Supply and fixing MCB SPN, 40 Amps, 240 volt,10 KA ,\"B\" curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed . Cat part No 811035 of make Indoasian or equivalent make given in Appx \"B\". |
| 102 | Supply and fixing MCB SP, 5 to 32 Amps, 240 volt,10 KA ,\"B\" curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed . Cat part No 811008 to 811015 of make Indoasian or equivalent make given in Appx \"B\". |
| 103 | Supply and fixing sheet metal enclosuretriple pole & neutral(TPN) IP-43 including MCB, TPN63 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure , complete all as specified and as directed by the Engineer-in-charge. Cat part No.811841 of make Indo Asian or equivalentin make given in Appx \"B\". |
| 104 | Supply and fixing sheet metal MCB DB SPN 12 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed . Cat part No.811828 of make Indo Asian or equivalent make given in Appx \"B\". |
| 105 | Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB,.20 AmpS,, 10 KA, \"B\" curve including removing old unserviceable enclosure, complete all as specified and as directed by the Engineer-in-Charge.Cat part No. 811955 of make Indo Asian or equivalent in make given in Appx \"B\". |
| 106 | Material and labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthwire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test pointas directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testingas in repair complete all as directed by Engineer-in-Charge and earth testing on completion. |
| 107 | Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth for foundation etc or for laying cable etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed . |
| 108 | Returning, filling in, including spreading, levlling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge. |
| 109 | Removing surplus excavated materialto a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge. |
| 110 | Supply, laying,testing & commissioningXLPE insulated, armoured heavy duty electric cable 25 sqmmcross sectional area, 4 corewith stranded aluminium conductor, 1100 volts grade as in repair complete all as specified and as directed. |
| 111 | Supply and laying well burnt brick class–B laid flat to cover the cable with width equal to the length of cable and abutting each other for protection of cable complete all as specified and as directed. |
| 112 | Material and labour for dry sand cushoning to cable i.e 8 cm before laying cable in trenches and 15 cm after laying the cable and compacting complete all as specified and as directed Note: punned thickness shall be measured for payment. |
| 113 | Supply and fixing as in repairlight grade GI Tubing of size 40mm dia for cable protection and fixed with clamp to pole and wall with nut, bolts, washers complete all as specified and as directed. |
| 114 | Taking down ceiling fan, cleaning the same and refixing after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed. |
| 115 | Note:-Amount of credit ofRs. 92,845.00 for retrieved materials is mentioned in Schedule of Credit Page No. 123 & 124 of tender doCubicmetre ents in pdf form which will be deducted offline while acceptance of tender. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
