|
| 1 | Taking down chowkats or frames with shutters n.exc. 1.50 Sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutters exc. 1.50 sqm but n.exc 4.00 sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 3 | Supply and fix factory made 30mm thick second class hardwood plain framed panelled shutters (any numbers of panels) with panels of timber flat both sides (feather edged) or of veneered particle board medium density, wood particle with commercial face veneers and fitted to chowkats complete all as specified and directed. |
| 4 | Supply and fix 30mm thick 2nd class hard woodGlazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all asspecified and directed. |
| 5 | Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. |
| 6 | Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed. |
| 7 | Supply and fix solid PVC door frame of size 50x47 mm made out of 5mm PVC sheet plain colour reinforced with MS square tube as per specification and drawinggiven in SSR Part-II 2020 complete all as specified and directed. |
| 8 | Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement as per specification and drawinggiven in SSR Part-II 2020 complete all as specified and directed. |
| 9 | Supply and fix 125mm size stainless steel butt hinges medium weight fixed with screw or welding complete all as specified and directed. |
| 10 | Supply and fix 50mm size stainless steel butt hinges medium weight fixed with screw or welding complete all as specified and directed. |
| 11 | Supply and fix 200mm long aluminium handles, cast type, anodized complete all as specified and directed. |
| 12 | Supply and fix 200mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 13 | Suplly and fix 300 mm long aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy complete all as specified and directed. |
| 14 | Supply and fix door stopper 150mm long cover plate, aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed to shutter complete all as specified and directed. |
| 15 | Supply and fix hydraulic regulated door closer aluminium extruded section body designation No. 3, universal type, suitable for aluminium doors etc. complete all as specified and directed. |
| 16 | Material and labour for second class hard woodsmall fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary\" labours; articles n. exc 200 cu. cm each complete all as specified and directed. |
| 17 | Supply and fix 4 mm thick sheet glass ordinary quality and glazing with oil putty / wooden bead/ aluminium bead/ rubber bead in square n. exc 0.5 Sqm in each pane complete all as specified and directed. |
| 18 | Supply and fix 4 mm thick sheet glass ordinary quality and glazing with oil putty / wooden bead/ aluminium bead/ rubber bead in square exc 0.5 Sqm in each pane complete all as specified and directed. |
| 19 | Supply and fix solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed. |
| 20 | Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 21 | Supply and fix stainless steel 25mm dia curtain rod, fancy type with stainless steel side and end holders and stainless steel brackets fixed in brick /concrete wall with screws complete all as specified and directed. |
| 22 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises completeall as specified and directed. |
| 23 | Demolition of cement concrete (unreinforced) in ground floors and paving n.exc. 15cm thick (below or above ground level) and removal of rubbish from the site complete all as specified and directed. |
| 24 | Material and labour for 40mm thick PCC (1:2:4) type B-1 (using 20mmgraded stone aggregate) as in levelling course for laying floor finishes complete all as specified and directed. |
| 25 | Material and labour for ceramic, non skid coloured tiles (premium quality) 7 to 8mmthick (square/rectangular) area of each tile exceeding 0.11sqm but not exc. 0.18sqmas in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar (1:6)complete all as specified and directed. |
| 26 | All as per item No 25.00 above but in skirting and dado laid over and including 10mm thick rendering in cement mortar (1:4) and -ditto-. |
| 27 | Material and labour for glazed ceramic tiles of size 300x450x7-8 mm (premium quality) coloured in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick cement plaster in cement mortar (1:4) completeall as specified and directed. |
| 28 | Material and labour for 75mm thick PCC (1:3:6) typeC-1 (using 20mm graded stone aggregate) as in plinth protection, laid in panels including finishing theconcrete surface even and smooth without using extra cement including forming costruction joint 30mm deep x 10mm wide filled with sealing compound of group \"A\" complete all as specified and directed. |
| 29 | Material and labour 75mm thick PCC (1:4:8), type D-2 (using 40 mm graded stone aggregate) as in sub-base or base course of floor complete all as specified and directed. |
| 30 | Material and labour for 10-12 mm thick grandura digital vitrified tiles (premium quality) of any colour and shade combination in matt finish for outdoor pavements (good grip series) of size n. exc 0.16 sqm, coloured, set jointed and pointed in neat cement slurry with grey cement & pigment as in floor, path etc. laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed. |
| 31 | Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 32 | Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for key, scrubbingdown with water etc. and removing debrish from site complete all as specified and directed. |
| 33 | Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars etc.including removing of unserviciable material from site complete all as specified and directed. |
| 34 | Material and labour for brick work with sub class `B` bricks, old size,straight or curved on plan exc 6m mean radius built in cement mortar (1:6)complete all as specified and directed. |
| 35 | Material and labour for 10mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:6) andfinish the surfacesfair and even on wall complete all as specified and directed. |
| 36 | Material and labour for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar (1:4) andfinish the surfaceseven and smooth without using extra cement as in wall complete all as specified and directed. |
| 37 | Material and labour for 10mm thick dubbing out plaster on irregular face of walls / ceiling and rough finished in cement mortar (1:4) including GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed. |
| 38 | Material and labour for 5mm thick rendering onconcrete surfaces in cement mortar (1:3) andfinish the surfaceseven and smooth without using extra cementin ceiling complete all as specified anddirected. |
| 39 | Supply only liquid water proofing compound (WPC) completeall as specified and directed. |
| 40 | Material and labour for preparation of new plastered surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer complete all as specified and directed. |
| 41 | Material and labour for preparation of new plastered surfaces of ceiling and applying three coat of white wash completeall as specified and directed. |
| 42 | Material and labour for preparation of new plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion paint (camouflage pattern) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming one coat of exterior primer applied @ 0.90 litre/ 10 sqmcomplete all as specified and directed. |
| 43 | Material and labour for preparation of new wooden surfaces of any description exc 10 cm width or girthand applying two coats ofsynthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 44 | Materials and labour for complete removal of existing treatment of old decorated surfaces of walls and applying two coats of acrylic washable distemper over a coat of alkali resistance primer including preperation of surface complete all as specified and directed. |
| 45 | Materials and labour for applying 2mm thick wall care putty including rubbing etc to achieve smooth surface complete all as specified and directed. |
| 46 | Material and labour for complete removal of existing treatement on old decorated surfaces of walls and applying two coats of 100% premium acrylic emulsion paint (camouflage pattern) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming one coat of exterior primer applied @ 0.90 litre/ 10 sqm including preparation of surface complete all as specified and directed. |
| 47 | Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, fins, facia, chajjas and similar suspended work including reinforcement cut as required to facilitate demolition and removing debries from site of work completeall as specified and directed. |
| 48 | Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed. |
| 49 | Material and labour for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bres-summers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished flat surfaces of concrete complete all as specified and directed. |
| 50 | Material and labour for RCC (1:2:4) (nominal mix) type B-1 (using 20mmgraded stone aggregate) as in beams, cantilevers, bressummers, lintels complete all as specified and directed. |
| 51 | Material and labour for green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade laid over and including 20mm thick screed bed in cement mortar (1:6) complete all as specified anddirected. |
| 52 | Providing edge moulding to 18-20mm thick marble stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified anddirected. |
| 53 | Supply, hoist and fix 500 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20 mm boreball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule and including dismantling of old unseviciable existing tank and removing from site complete all as specified and directed. |
| 54 | Material and labour for cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exc 10 cm girth complete all as specified and directed. |
| 55 | Taking up or down 15 mm bore steel tubing and connections, including removal from site complete all as specified and directed. |
| 56 | Supply and fix 15 mm bore steel tubesmedium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floorscomplete all as specified and directed. |
| 57 | Taking up or down 20 mm bore steel tubing and connections, including removal from site complete all as specified and directed. |
| 58 | Supply and fix 20 mm bore steel tubesmedium grade, galvanised, with all fitting and fixed to walls, ceilings, roofs or laid in floors complete all as specified and directed. |
| 59 | Supply and fix gun-metal globe or gate valves 20 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed. |
| 60 | Supply and fix in repair 15mm bore cast copper alloy chromium plated fancy type angle cock for iron pipe complete all as specified and directed. |
| 61 | Supply and fix in repair 15mm bore stop valves, castcopper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed bothends for iron pipe or for unions complete all as specified and directed. |
| 62 | Supply and fix in repair 15mm bore fancy type, chromium plated, long body bib tap, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed. |
| 63 | Supply and fix in repair soap dish, brass, chromium plated complete all as specified and directed. |
| 64 | Supply and fix in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 65 | Supply and fix in repairPVC connection pipe 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 66 | Supply and fix in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and directed. |
| 67 | Supply and fix in repair brass chromium plated shower rose 125mm size with or without swivel joint complete all as specified and directed. |
| 68 | Supply and fix looking mirror ofsize 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers completeall as specified and directed. |
| 69 | Supply and fix in repair vitreous china wash down water closet pan (pedestal Pattern) white (excluding fixing bolts flusing cistern and flush pipe) including connection to drain (or out going pipe) and to flush pipe anti syphonage pipe including cast iron P or S trap fixed on floorcomplete all as specified and directed. |
| 70 | Supply and fix in repair vitreous china squatting pan (Orissa pattern) water closet (white) size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling complete all as specified and directed. |
| 71 | Supply and fix in repair vitreous china wash hand basin, white, of size 580mmx450mm fixed to granite/marble top slab, including cutting for and pinning in and 32 mm bore cast copper alloy chromium plated waste fittings and 32mm dia PVC waste pipe 800mm long including 15mm bore fancy type long body pillar tap cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed. |
| 72 | Supply and fix 50mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 with all fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed. |
| 73 | Supply and fix in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 74 | Supply and fix in repair 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 75 | Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 76 | Supply and fix in repair 75mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 77 | Supply and fix in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including stack clamp of suitable size complete all as specified and directed. |
| 78 | Supply and fix in repair 110 mm bore PVC (SWR) bends with access door any radius complete all as speified and directed. |
| 79 | Supply and fix in repair 110 mm bore PVC (SWR) bends complete all as speified and directed. |
| 80 | Supply and fix in repair 110 mm bore PVC (SWR) vent cowl complete all as specified and directed |
| 81 | Supply and fix in repair 125mm PTMT grating doom(minimum weight 40gms) complete all as specified and directed. |
| 82 | Material and labour for providing, cement concrete (1:2:4) type B-0 (using 12.50 mm graded stone aggregate) in roof kerbs ormud stops, rounded or chamfered on edges of walls/columns etc complete all as specified and directed. |
| 83 | Material and labour for cutting out cracks to V-section in existing roof or terracing, cleaning and filling solidly with hot mixture of bitumen and clean dry sand (1:1) (by weight) complete all as specified and directed. |
| 84 | Material and labour for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified and directed. |
| 85 | Complete removal of existing roof treatment in any layers and disposal of debris from site complete all as specified and directed.Notes: - (a) The rates are inclusive of removal for any type of old water proofing treatement over main RCC slab.(b) Bidders are advised to visit the site and esure about site condition before quoting their rates.(c) Demolition of PCC/ taking down plaster if any shall be measured and paid saparately under respective items. |
| 86 | Demolition of cement concrete (un-reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, fins, facia, chajjas and similar suspended work including removal of debris from site complete all as specified and directed. |
| 87 | Material and labour for PCC (1:2:4) type B0 (using 12.50 mm graded stone aggregate) mixed with water proofing compound @ 200 ml per bag of cement (50 Kg) or as per manufacturer instruction as in levelling course to match undulation of roof, in coving, roof kerbs including benching or mud stops, rounded or chamfered on edges etc including necessary form work and finished the rough surface complete all as specified and directed.Note : WPC will be measured and paid separately under respective item. |
| 88 | Material and labourfor 5mm thick rendering in cement mortar (1:3) with using water proofing coumpound (WPC) @ 200 ml per bag of cement (50 Kg) or as per manufacturers instruction on roof top while concrete is green to become integrated part of concrete padding layer and finish the surfaceseven and smooth without using extra cement complete all as specified and directed.Note : WPC will be measured and paid separately under respective item. |
| 89 | Material and labour for water proofing treatment to RCC roof surface with fiber reinforced elastomeric liquid applied waterproofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibers and upon curing forms a thick, seamless, durable membrane using product Smart Care Damp Proof Ultra (Product code- 5698) of Asian Paints Ltd or equivalent brand of makes M/s STP Ltd, M/s IWL India Ltd, M/s Tiki Tar Danosa (India) pvt ltd, M/s FOSROC Chemicals with the following course of treatment/specifications from bottom to top :-(a) Applying priming coat Smart Care Damp Proof Ultra as self priming with 33% water dilution with roller/ brush and allow to dry for 4-6 hours or as per manufacturer\"s instruction.(b) Applying first coat of water proofing Smart Care Damp Proof Ultra without dilution with roller and allow to dry for 4-6 hours or as per manufacturer\"s instruction.(c)Finally applying second coat of water proofing Smart Care Damp Proof Ultra without dilution with roller and allow to dry for 4-6 hours or as per manufacturer\"s instruction.Note:- The work shall be executed only through authorised applicator of manufacturer as approved by GE. |
| 90 | Material and labour for well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 91 | Material and labour for structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes including one shop coat of red oxide zinc chrome primer complete all as specified and directed. |
| 92 | Supply and fix 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and directed. |
| 93 | Supply and fix 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 94 | Material and labour for light/fan point wiring (concealed type) with single core PVCinsulated unsheathedmultistranded FRLSH copper conductor cable of 1100 volts grade size 1.5 sqmm (nominal area) in and including heavy duty rigid non metalic 20mm dia PVC conduit with accessories including with 1.2mm thick pressed steel terminal boxes in flush to existing wall surface with 3mm thick bakelite sheet top cover (ISI marked) fixed with chromium plated brass screws and cap washers suitable for housingswitches, sockets and regulatorswith all fittings and fixing materials with one single core PVC insulated unsheathed 1.5 sqmm (nominal area) multistranded FRLSH copper conductor as earth continuity wire and connected to earth dully including taking down existing point wiring complete all as specified and directed.Note: (a) Red coloured cable shall be used for live connection,black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.(b) Quoted rate shall be included for cuttings /chasing the wall and making good disturbed surfaces to fix PVC conduit and MS terminal box. |
| 95 | All as per item No. 94.00 here-in-before but for one five pins 5 Amps switch socket outlet point on independent board and -ditto-. |
| 96 | All as per item No. 94.00 here-in-before but for one five pins 5 Ampssocket outlet point on same board and -ditto-. |
| 97 | All as per item No. 94.00 here-in-before but for 15 amps socket outlet on independent board with 2.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade including 2.5 sqmm PVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts grade as earth continuity conductor and connecting to common earth dollyand -ditto-. |
| 98 | Supply and fix switch piano one way 5/6 amps240 volts, single polecomplete allas specified and directed. |
| 99 | Supply and fix socket outlet2 in 1, 3 pin 5 Amp flush type complete allas specified anddirected. |
| 100 | Supply and fix switch socket combination 2 in 1,5 pin , 5 amps flush type complete allas specified and directed. |
| 101 | Supply and fix switch socket combination 5 in 1,5/15 amps socket complete allas specified anddirected. |
| 102 | Supply and fix ceiling rose, 3 terminals, fabricated of PVC/Polycarbonate, isolated body complete all as specified and directed. |
| 103 | Supply and fix delux steppedtype electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed. |
| 104 | Supply and fix lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete allas specified and directed. |
| 105 | Supply and fix in repair sheet metal enclosureSPN DB 8 waysdouble door having facility to fix MCB in incomer and MCBs in outgoing,metal door IP-43type complete fitted with bus bars, neutral links, blanking plates complete all as specified and directed. |
| 106 | Supply and fix in repair MCB SPN, 240 Volts, 40amps, \"C\" series, breaking capacity 10 KA complete all as specified and directed. |
| 107 | Supply and fix in repair MCB SP, 240 Volts, of 6 to 32 amps current rating, 10 KA breaking capacity \"C\" series complete all as specified and directed. |
| 108 | Supply and fix in repair LED tube light fitting 1 x 20W (+/- 5%), 220V, AC with extruded strip in thermally conductive material & extruded housing in optically efficient material milky white with system lumen efficacy > 120 lumen per watt minimum system 2300 - 2400 and chip, Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, Power factor > 0.95, THD less than 15%, correlated Colour temperature (CCT) of 6500K, Operating Voltage of 140 V to 270 V, frequency of 50Hz burning hours 50000 hours with comprises of CRCA pre coated metal housing complete all as specified and directed. |
| 109 | Supply and fix in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep, minimum air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete all as specified and directed.Note: - Old unserviceable fan shall be deposited to E/M store. |
| 110 | Supply and fix 300mm sweep steel body exhaust fan AC single phase 230/240 volt. 1400 RPM, heavy duty, ISI marked, along with metal blade powder coated metalic finish with GI sheet louvers, low noise including necessary electric connection with and including cutting/making opening having dia of the hole for 300mm sweep exhaust fan inany type of walls of any description with nut, bolt, washer and making good distrubed surfaces complete all as specified and directed. |
| 111 | Supply and fix wall mounted fan, metal body AC single phase. 230V of size 450 mm sweep, with, blades, and frames complete all as specified and directed. |
| 112 | Supply and fix in repair LED street light fitting 35 Watt, 230 volts made with pressure die cast housing with toughened glass with high powered LED, IP-66 protection high power LED with secondary lenses and system efficiency should be minimum 110 lumen per watt. Driver should be BIS approved silicon filled potted driver with inbuilt 4KV surge protection device, THD shall be <10%, power factor >.95, CCT 5700K and brand name should embossed/engraved on the LED fitting for traceability till life complete all as specified and directed. |
| 113 | Material and labour for earthing complete with GI earth plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI wire 4 mm dia earth lead by means of nuts, bolts, check nuts, washers of galvanized iron as steel,protected by 15mm dia GI pipe (medium grade) including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x 6 cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel,wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, earth testing point, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion including taking down existing earthing set complete as specified and directed.Note:- GI wire upto 7.5m including testing shall be included in qouted rates. |
| 114 | Material and labour for earth continuity conductor or main earthing lead with4mm dia GI wire, fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or DB\"s / Indoor type LT PBs orany other indicated situation for loop earthing etc complete all as specified and directed |
| 115 | Supply, laying, connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty with stranded aluminum conductor)of size 10 Sqmm, 2 core, 1100 Volts, confirming to IS-7098 (Part-I) laid through duct/ pipe / in trench etc. with cable glands & suitable size of aluminium lugsincluding taking down existing cable complete all as specified and directed.Note : Earth work, brick protection and sand cushioning and GI Pipe Shall be measured and paid separately under respective item. |
| 116 | Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 m in depth for foundation etc or for shafts, wells, cess pits man holes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 117 | Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed. |
| 118 | Removing excavatedmaterial (soil) notexc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 119 | Material and labour for sand cushioning with clean and dry river sand for protection of XLPE UG cable with approved sand of uniform thickness. laid dry, filling in trenches and punning down in proper required layers complete all as specified anddirected. Note:- Punned down thickness shall be measured for payment. |
| 120 | Material and labour for brick protection cover to underground cables with sub class ‘B’ of size 23 X 11.5 X 7.5 cm, (locally available best quality), laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed. |
| 121 | Materials and labour for boring for passing GI protection pipe up to 50 mm bore (dia) under road / footpath without disturbing the top surface including Supply and fix GI tubing of size 50mm dia (light grade) with all fittings, under footpath / road crossing etc. for protection of cables complete all as specified and directed.Note-Necessary infrastructure required for boring shall by arranged by the contractor and cost of the same included in quoted rates. |
| 122 | Supply and fix in repair 25 mm bore steel tubesmedium grade, galvanised, with all fitting and laid in trenchescomplete all as specified and directed. |
| 123 | Supply and fix in repair gun-metal globe or gate valves 25 mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed. |
