|
| 1 | Cleaning manually of blocked WC seat trap, inside house and gully trap it includes remove/refixing of grating and cleaning of WC\"s trap,kitchen/bath trapsany type/pattern (pedestal/squatt pattern) upto 1st manhole and making the drain pipe of any size full functional by flushing with water to entire satisfaction of Engr-in-Charge including cleaning of 1st manhole and removing the waste material/sludge etc toout side form defence landand burring the same in pits complete all as directed by Engr-in-Charge.(Measurement will be carried out each time depend on blockage) |
| 2 | Cleaning of underground SGSW pipes of size 150mm dia by rodding from manhole to manhole or manhole to septic tank/well including taking off manhole cover and cleaning of manholes of any size and depth and removing waste material/sludge to a distance of n. exc 50m and burrying the same pit and replacing manhole cover in position after cleaning (measurement will be carried out each time depend on blockage) complete all as specified and directed by Engr-In-Charge. |
| 3 | Cleaning and dewatering of septic tanks/pits of any depth incl let and outlet chamberand removing slauge (in solid and semi solid), silt, both organic and in-organic nature including any type of waste matterial after plugging of incomimg sewage line and removing waste material / sludge etc to out side form defence land and burrying the same in pit complete all as specified and directed by Engr-In-Charge. |
| 4 | Removing of Sludge, mud from sewage sumpwell, manhole ,sokpit, sokage well of any depthincl let and outlet chamber (in solid and semi solid), silt, both organic and in-organic nature including any type of waste matterial/sludge with Mechaniclly or manual which are required on ground without any other financial effect etc to a distance n. exc 100m and burrying the same in pit complete all as specified and directed by Engr-In-Charge. |
| 5 | Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. complete all as specified and directed. |
| 6 | Demolition un-reinforced cement concrete in ground floor and paving any surface, complete all as specified and directed. |
| 7 | Demolition reinforced cement concrete ofany depth and any postion complete all as specified and directed. |
| 8 | Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegetation upto and including roots upto 30mtrs height from ground complete all as specified and directed.Note: This included any thick of plaster and already of tiles or mosaic tiles etc. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge. |
| 10 | Taking up or down steel tubingfor 15mm dia pipe and connections including cleaning up to 4th storey for re-fixing or removal to store complete all as spd and directed by Engr-in-Charge |
| 11 | Taking up or down steel tubing for 20mm dia pipe and connections including cleaning for re-fixing or removal to store complete all as spd and directed by Engr-in-Charge |
| 12 | M&L for 15mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floors complete all as specified. |
| 13 | Re fixing only15mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floors complete all as specified. |
| 14 | M&L for 20mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floors complete all as specified and dirceted. |
| 15 | Re fixing only 20mm dia bore galvanized steel water tubing, “medium grade,” together with all fittings; (ISI marked) such as elbows, bends tees, nipples, union sockets, sockets etc and short pieces and fixed complete to walls and ceilings or laid in floor complete all as specified and dirceted. |
| 16 | Disconnecting existing tanks capacityexc-500 but n-exc 10000of tanks any capacity litre setting aside (or lowering if required) for repair, cleaning etc and hoisting if required reconnecting and re-fixing in position including Cleaning & removing all dirt and scale from tank and also from mouth of pipecompletly as directed by Engineer-in charge. |
| 17 | S&F in repairs PVC water tank cover for 1000 Litre and 500 Litrecapacity includingproper fixing with clamp &nut bolt complete all as specified. |
| 18 | Excavation in trenches in any type soilnot exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth in foundation etc for manholes, sewage line and getting out Complete all as specifed and directed by Engr-In-Charge. |
| 19 | Returning filling in including spreading levelling , watering and well ramming in layers not exceeding 25 cm Complete all as specifed and directed by Engr-In-Charge. |
| 20 | Removing excavated material soft and loose soil exceeding 250 Mtrbut n-exc 500Mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point Complete all as specifed and directed by Engr-In-Charge. |
| 21 | Demolition and breaking up drain 200mm dia pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed by Engr-in-Charge. |
| 22 | Dismantling of cast iron reinforced concrete drain pipes of any size, jointed in cement mortar and taking out tranches if required complete all as specified.(Note : Dismantling ofany size Cast ironincludingPVC pipe involve without Extra charge. |
| 23 | Cutting into existing manholes any size or any type for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed by Engr-in-Charge. |
| 24 | M&L for 200mm thickconcrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150/200 mm SGSW pipes complete all as specifiedand as directed by Engr-In-Charge. |
| 25 | S&F for reinforcement concrete pipes, class NP-2 laid and jointed complete with collars bore of pipe 200mm , fixed in cement mortar 1:3 complete all as specifiedand as directed by Engr-In-Charge. |
| 26 | M & L for cement concrete (1:4:8) type D-2 (40mm graded stone aggregate) in foundations Complete all as specifed and directed by Engr-In-Charge. |
| 27 | S&F for Slat-glazed stoneware (SGSW) grade \"A\" drain pipes 200mm bore laid in trenches and jointed on concrete bed, complete including testing etc complete all as specified and shown in drgs (Concrete bed shall be measured and paid for separately). |
| 28 | M&L for brick work with sub class \"B\"old size bricks straight or curved on plan exceeding 6 Mtr mean radius built in CM (1:6) for man holes and external pointed flush in same mortar as the work proceeds Complete all as specifed and directed by Engr-In-Charge. |
| 29 | Excepet Bricks work with old size bricks, using old serviceable bricks, as retrieved from dismantling of brick work under respective item, after removing mortar from and cleaning bricks; straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed. |
| 30 | S&F Cutting holes of surface areaexc 150 to 400 Sqcm into or through brick walls built in mud /cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed. |
| 31 | M & L for dismantling old abondandmanholeby demolition filling debris and making good to ground surface complete all as specified and directed. |
| 32 | M&L PCC 1:2:4 type B1(Using 20mm graded stone aggregate )as in benching, bed plates, coping and the like including weathering, slightly rounded or chamfered angles as direceted including necessary form work and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge. |
| 33 | Extra for forming fair finishingdrain or channel 30 cm inner girth in cement concrete , using extra cement including forms, moulds etc complete all as specified. |
| 34 | Rendering 15mm thick cement plaster in cement mortar 1:4 on fair face of brick work or concrete surface, finished even and smooth without using extra cement, with waterproofing compound admixture complete all as specified and as directed.Note:-Supply only liquid water proofing admixture shall be measured and paid seperately under relevant item of this BOQ |
| 35 | Supply only LiquidWater Proofingadmixture complete all as specified and directed by Engineer-in-Charge. |
| 36 | Precast cement concrete type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in manhole cover/drain coverset in CM 1:4complete all as specified incl form work and directed. |
| 37 | M&Lflat concrete surface for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick on concretefair finished surfaces (Horizontal or sloping) complete all as specified. |
| 38 | M&L for 25mm thick PCC type B-0 1:2:4 (12.5mm graded aggregate in flooring finishing rough to recieveing Top layerfor flooring complete all as specified and directed. |
| 39 | M&L for glazed ceremic tiles 300x250x7 mm or 450x350x7 mm thick, as in dado, vertical surfaces set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed. |
| 40 | M&L for Joint free colored non skid ceramic tiles7to 8 mmthick, area of each tileexc 0.11 sqm but n exc 0.18 sqm in floors etcset and jointed in neat cement slurry and pointed in colored cementover and incl 15 mm thick screed bed orbedding layers of cement mortar 1:4 to matchShade, pattern, laying etc of tilescomplete all as specified and directed. |
| 41 | M&L chequered or machin pressedcement concrete coloured tiles machine pressedconforming to IS 13801:1993 and ISI marked, size not less than 300mm x 300mm (Approx), thickness 25mm, as in floor, paving set and jointed in neat cement to match with grey pigment all as specified and directed. |
| 42 | Providing and laying at or near ground level actory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 43 | M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking pave rblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;completeall as specified and directed. |
| 44 | S&F for in repair Angle valve cast copper alloy chromium Plated (CP)15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or forunions and fixed complete all as specified and dirceted. |
| 45 | S&F for in repair CP Bib taps long nose 15mm dia screwed down high pressure with crutch or butter fly handles screwed both and iron pipe or forunions and fixed complete all as specified and dirceted. |
| 46 | S&F in repairs Health faucet(ABS body) mild steel chrpmium platedsutaible for 15 mm dia pipe with 1.25 Mtr longflexible tube and ABS Wall hook including making connections and fixed in position complete all as specified and directed by Engr-in- charge |
| 47 | S&F in repair CP Jet spary with one meter flexible tube 15mm dia for EWC including all connection complete all as specified and dirceted. |
| 48 | Dismantling 1000 ltr water tanks and removing to store complete all as specified. |
| 49 | Dismantling 500 ltr water tanks and removing to store complete all as specified. |
| 50 | S&F Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes complete all as specified and as directed by Engr-in-Charge. |
| 51 | S&F Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes,complete all as specified and as directed by Engr-in-Charge. |
| 52 | S&F for repair toilet paper holder fancy type chromium plated screwed down for fixing to wall with screws complete all as specified and dirceted. |
| 53 | Fixed in repairs 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets, PVC 32mm dia flushing pipe for cistren ete complete fixed in repairs all as specified and directed. |
| 54 | S & F PVC (SWR) pipes single socketed in any length with rubber ring joints in trenches bore of pipe 110 mm with PVC clamps and saddles including taking down existing (SGSW/PVC) pipe and fittings. |
| 55 | S&F in repair 110mm bore Cast Iron (SWR) \"S\" trap, including fixed with solvent cement complete all as specified and directed. |
| 56 | S&F in reapirvitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing of flushing cistern, brackets, flushing pipe, and CP jet spray including CP flexible pipe for EWC etccomplete all as specified. |
| 57 | Vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white withfront or back inlet with integral \"foot rests including provn of lime concrete bedding excluding connections to \"flushing cistern/pipe, \"Fixed in repair\" complete all as specified and directed. |
| 58 | Supply and fixing in repairs vitreous china urinal flat back 465x355x265mm size , including grating and Connection to flushing pipe and outgoing pipe complete all as specified |
| 59 | S&F for in repair 15mm dia 450mm long PVC connection with PTMT nut and washer complete all as specified and directed. |
| 60 | S&F in repairPVC grade \"A\"pipes 110mm bore laid in trenches and jointed on concrete bed, complete including testing etc complete all as specified and shown in drgs. |
| 61 | S&F in repair Stack clamps 75/100mm diafor out of 50 mm by 5 mm flat iron round 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roofwith proper mannercomplete all as specified and directed. |
| 62 | M & L with Tools grubbing up tree trunk including roots portion from wall /roof filling holes with PCC and making the surface finished with Cement plaster CM 1:3 upto 4th storey of Bldg complete all as specified and directed. |
| 63 | M&L for removal of vegitation / trees grith exc 30cm n. exc 100cm from wall, roof top and CI/PVC sewer lines on wall upto height of 4th storey bldgs incl waste materials removing from site upto the distance of 100m and area of removal places filling with PCC/CM 1:4 as site required,complete all as specified anddireted by Engineer in charge.Note:- Contractor arrange his own suitable T&P as per site requirement and nothing extra shall be paid for the said work.PCC & CM 1:4 if any required will be measured and paid separately. |
| 64 | Saptic tank with cover slab at GL of 25 users capacity with inlet chamber, brick work in CM 1:4 M-25 (Design mix) concrete in cover slab, internal plaster 20mm thick in cement mortar 1:3 using water proofing compound including necessary excavation and earth work in any type of soil,RCC precast manhole covers with angle iron welded frame, CI vent pipe 100mm dia with cowl complete all as specified and shown on CEAF/STD-15/2000 sheet No 1/2 & 2/2 |
| 65 | Soakage well 3.00 metre dia and 3.00metre deep below inlet (depth) from inlet pipe to ground level 45cm including excavation and earth work in any type of soil,PCC 1:4:8 type D-2 in foundation ,RCCM-25(design mix ) cover slab wall in honey combed brick work in cement mortar 1:4, earthcousinon brick lining on top ,filling with brick bats and inlet pipe 150mm dia complete all as specified and shown on DrgNo-CEAF/STD-15/2000 sheet No 1/2to 2/2. |
| 66 | Note (Srl item no 1 to 65):-i) All the complaint(s) received will be lodged & rectified by the contractor rep and will have to maintain a proper record as directed in complain register and in complain slip.(ii) Complain slip and complain register will be provided by the contractor without any extra charge.(iii) Complain register will be produced on daily basis to JE and Engr-in-charge (iv) Thenew items provided shall be measured and paid for separately under relevant items of Sch ‘A’.(v) If contractor fails to attend the complaints in 48 hours a recovery of Rs 300 shall recovered per complaint. (Vi) Saptic tank soakage well work will be Execute as per drawingand after complete the work all wastage material remove the side and dumping mtrial out side the Defence Land without any Extra charge. (vi) Any Misc items reqd viz. colours, putty, Machenically Equipment which are required on groundetc in the work should be deemed incl in the respective items of works and nothing extra shall be paid on the account. |
| 67 | M&L for Brick work with sub class \"B\" bricks, straight or curved on planto any redius in half brick thick wall builtin cement mortar 1:4, complete all as specified and directed. |
| 68 | M&L for 100 mm thick plain cement concrete 1:4:8 type D2 (40mm graded crushed stone aggregate) as in sub base of flooring complete all as specified and as directed by Engr-In-Charge. |
| 69 | M&L 75 mm thick PCC 1:3:6 type C1 using 20 mm graded stone agg in Sub floor, finished even and fair w/o using extra cement. |
| 70 | M&L 100 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggas in ,floors and Pavings etc, finished even and smooth w/o using extra cement Complete all as specified. |
| 71 | M/L Cement concrete 1:3:6 type C-2 using 40mm graded stone crushed aggregate in plinth protection, 75mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete. |
| 72 | M&Lto Sand filling under floors or in foundations including watering and consolidation Complete all as specified. |
| 73 | M&L for reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for slabs supported on wall, beams and columns, in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ,complete all as specified and directed Note : Reinforcement shall be measured and paid for separately. |
| 74 | M&L for use and waste of formwork to flat faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, rough finished surface complete all as specifed and directed. |
| 75 | M&L for Steel reinforcement 10mm dia and over, TMT bars, cut to length, bent to shape required including, cranking, bending, spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and directed . |
| 76 | M&L for steel reinforcement 6 to 8mm dia and over, TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed . |
| 77 | M& L cement concrete 1:3:6TypeC-1 (20 mm graded Aggregate ) in surface channels and drainas all aspecified and directed by Engr in charge. |
| 78 | M&L 10mm thick renderingon fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on internal walls in cement mortar 1:6, complete all as specified and directed by Engr-in-charge. |
| 79 | M&L15mm thick renderingon fair faces of brick work or concrete surfaces, other than fair face(without using extra cement) on external walls in cement mortar 1:4 including WPC complete all as specified and directed by Engr-in-charge.Note: Supply only liquid water proofing admixture shall be measured and paid seperately |
| 80 | M&L 5mm thick rendering on fair faces on concrete surfaces/ ceiling, finished even and smooth (without using extra cement) on walls in cement mortar 1:3, complete all as specified and directed by Engr-in-charge. |
| 81 | Demolition and breaking up drain 300mm dia pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed by Engr-in-Charge. |
| 82 | S&F for reinforcement concrete pipes, class NP-3 laid and jointed complete with collars bore of pipe 450mm , fixed in cement mortar 1:3 complete all as specifiedand as directed by Engr-In-Charge. |
| 83 | M/L Cement concrete 1:3:6 type C-1 using 20 mm graded crushed stone aggregate in roof kerbs or mud stops, kurb ston copingcillsmalar bends Plint course , rounded or chamfered on edge including necessary form work complete. |
| 84 | M & L roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove duct etc complete all as specified. |
| 85 | M&L 20 mm thick screed bed or bedding layer in CM 1:6 finished fair and even for laying floor finishes/tiles etc complete all as specified and directed by Engineer-in-Charge. |
| 86 | M & L for prepration of new plasteredsurfaces and applying three coat of lime white wash on walls, all as specified. |
| 87 | M & L for prepration of new plasteredsurfaces and applying three coat of lime white wash on ceiling, all as specified. |
| 88 | Removal of soil/silt, Shrubs and other waste from the RCC& BrickdrainsUp toWide and dipth Approx (1.0x1.20) RM and cleaning the surface throughly for free flow complete all as directed by Engr-In-Charge.Note : All sluge and waste matrialhave carry out fromits locatonn out from Air Force sation. |
| 89 | Dismanting of fencing wire mesh & barbed wire etc |
| 90 | Dismantling wrought iron or mild steel work,frame work such as truss, wind tie, angle frame work , concertina coil of any description complete all as specified and as directed. |
| 91 | Excavation in post holes (or similar holes) each n exc 0.5 cum,and removing surplus soil to distance n exc 50m and making good surface of any type of soil. |
| 92 | M&L for MS work conforing to Fe-410-0 of Fe-310-0 Grade for fencing posts and struts in fencing and gate grill and grating including cutting bending top to shape as directed drilling holes matching for barbed wire etc. including all necessary drilling work complete and all as specified |
| 93 | Supply only chain link MS Galvanised 3.80mm dia and 50mm pitch of wire fencing including line wires, any mesh, size and type to any type of standars, rails, straining bolts, etc. including provision of binding wire complete all as specified. |
| 94 | Fixing only Chan link frncing including line wires, any mesh, size and type of standerds, rails, straining bolts,etc. including provission of binding wire complete all as specifired. |
| 95 | S&F Tie bars of 10mm dia in fencing for stiffening conforming to Fe-290,Gde -E-265 |
| 96 | Mild steel screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other ends, or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nutexc 5 cm long but n-exc 10cm, dia of shank 10 mm , complete all as specified and as directed |
| 97 | Preparation of steel or iron surfaces of any description, over 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 98 | Preparation of steel or iron surfaces of any description, n exc 10cm in width or girth not otherwise described and applying 2 coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified. |
| 99 | Supply and fixing Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of of standard rails straining bolts, including, securing or tying at crossings with and Provision of galvanised mild steel wire, stapples or steel pins, etc. as directed (each line wire to be measured) complete all as specified. |
| 100 | Restraining & resecuring including making good &repairs galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc as directed |
| 101 | Supply and fixing concertina coil with punched tape of 600 mm dia , centre core wire shall be minimum 2.5 mm dia of mild steel wire conforming toIS 280-2006. Galvanised coating of steel concertina coil shall confirm to the requirements as laid down for medium coated wire in IS 4826 \"Hot dipped galvainsed coating of round steel wires\" conretina coil shall be fixed in diamond shape with the help of dovetail two handle and spikes shall be fixed at both end of coil,minimum straight length of the wire 150 RM of 10 RM of work ,minimum weight 13.5 Kg for 10 RM of work i.e. 90gm per RM of wire complete all as specifed and directed. |
| 102 | Dismantling steel orasbetos cement (corrugated/ semi corrugated etc) sheet in roof covering complete all as specified and directed. |
| 103 | S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.Note:- work up to 10 m height. |
| 104 | All as per item No.6 but 0.80mmabove but plain sheet fix in valley gutter / ridge complete all as specified and directed. |
| 105 | Plain, Aluminiumsheeting,Alloy 31000 H4in ridges, hips, valleygutter, drip and straightflashing (length andgirth as fixed) complete all as specified. |
| 106 | S&F Framed work as in doors orgates of angle or other sectionwith gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or othercovering. Doors, etc. to beprepared for hanging or slidingwith and including either hooksand hinges or steel hangingdoor fittings (exclusive of steelsheeting or other covering,running rails and guides) andhanging; also fastening and fixing complete Fe-410 W(Gde E-250) quality Complete all as specified. |
| 107 | M&L for MS work as in roof trusses (framed) trussed, purlins ,post, rafters including distant pieces, cleats etc including cutting and welding required confirming to grade Fe 410-W grad quality \"B\" complete all as specified and directed. |
| 108 | M&L for MS work as in wind tie or any other work incl cutting, drilling holes etc. complete all as specified and directed. |
| 109 | M&L for MS Plates(plain or chequered) channels, square cut, notched chamfer or square cut or notched (ordinary and counter sunk) forming holes without any attachment with MS Gde Fe 410-quality \"B\" complete all as specified and directed. |
| 110 | S&F formwork toSquare, rectangular or polygonal sides of pillars,posts, struts, piers,columnsand stanchions fair finished surfaces complete all as specified |
| 111 | Taking down cement or cement lime plaster, any descriptionon brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete including removal all debries exceeding 50m but not exceeding 100m all as specified and directed by Engineer-in-Charge. |
| 112 | M & L for prepration of new plastered surfaces and applying two coat of approved shade of oil emulsion distemper on walls all as specified and directed. |
| 113 | M&L Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specifiedand directed by Engr-in Charge. |
| 114 | Complete removal of wall and ceiling exisiting treatment and applying 1mm coat of plater of paris(putty) one cote ofAcrylic Smooth exterior paint @ .835 ltr/10 sq of required shade over one coat of primerm complete all as specifiedand directed by Engr-in Charge. |
| 115 | M&L for preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint Complete all as specified and as directed. |
| 116 | M&L 75 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone agg in floor, complete all as specified. |
| 117 | Providing precast cement concrete orsimlar workof PCC 1:2:4 Type B-1 20mm graded aggregate(of any section indicated), with plain fair faces, including chamfers, weathering\"s, throat- ing etc. and set & jointed in CM 1:4 complete all as specified. |
| 118 | Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified. |
| 119 | Dismantling of roller, purlin, angle, pully, channel, angle, hanger gates including taking down shutterApprox up to Size of 5x9.00RM and fixed in same position (Adopting all safety measures and scaffolding) after rectification /repair/replacement of connected items Supply and fixing in repair for hanger gate oftop rollers , channels, angle, cleats, sliding bolts, pully and connected tems, which ever fixing and repair to doors with rollers of hanger gates,existing material removal and refixed in the same positionwith PPGI plain sheets, all works to be executed upto 12m height. Rollerssupportand middlepoint breaker of roller where side in stopped roller, which are weleded with angle and same fixedwith nuts & bolts for safety purpose of wheel. Contractorto arrange to all necessary arrangementof scaffolding and safety measures etc. |
| 120 | S&F in repairSteel rolling shutters, 1.25mm thickwith outball bearing, as specifiedincluding top cover, an choring rod, hasp and stapleand one shop coat of primer;erected in position as indicated, complete:push pull ormanual type complete all as specified and directed by Engineer-in-Charge. |
| 121 | S/F in repair Safety lever locks mild steelwith 4 levers forrollingshutterscomplete all as specified and directed. |
| 122 | S&F in repair Ball bearing for rolling shutters after removing all accessories which are required to be removing all accessories which are required to be removed and replacing the unserviceable ball bearings will refixed the accessories at the same place as specified and directed by Engr-in-Charge. |
| 123 | S&F Wire netting of stainlesssteel wire 1.4mm dia 25mm pitchfixed with tinned tacks of stainless steel wire staples complete all as specified and directed. |
| 124 | S&F for in Repair rain water pipe 200mm diawith single socket joints fixed to wall including bend or Tee which wiil be requiredwith stack clamp fixed in repair (work commence hight upto 12 mtr) complete all as specified and directed by Engineer-in-ChargeNote : All clamp reviting,or wildingin brick wall or weilding to steel surface without any extra cast.The contractor will be provide with all safty measures |
| 125 | S&F for in Repair rain water pipe 110mm dia with single socket joints fixed to wall with stack clamp fixed in repair (work commence hight upto 12 mtr) complete all as specified and directed by Engineer-in-Charge |
| 126 | S&F for in Repair PVC rain water pipe bend & shoes etc for 110mm dia pipe fixed in repair complete all as specified and directed. |
| 127 | Removing demolished material to a distance and depositingout site of AF stationWhere directed at a level not exceeding 1.5 KM above the starting point, complete all as specified and directed by Engineer-in-Charge. |
| 128 | SCHEDULE \"A\" PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch \"A\" Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder. |
