|
| 1 | Taking down chowkats or frame with shutters (without taking off shuttters from frames) size exc 1.5 Sqm but not exc 4 sqm each each and removing from site and making good disturbed surfaces as per existing specifications complete all as specified and as directed. |
| 2 | Taking down chowkats or frame with shutters (without taking off shuttters from frames) size n .exc 1.5 Sqm and removing from site and making good disturbed surfaces as per existing specifications complete all as specified and as directed. |
| 3 | S&F in opening complete solid PVC door frame of size 50mm x 47mm made out of 5mm one side prelaminated any colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 4 | S&F for factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S. tube for top & bottom rails. MS frame shall be covered with heat moulded prelaminated decorative any colour PVC `C\" channel having a PVC sheet strip of 20mm width stuck inside wqith solvent cement for stiles and prelaminated colour PVC sheet for top rail, Lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelaminated decorative colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement fixing in frame at site as per specified |
| 5 | Providing & fixing of Pre-painted Galvanized Steel Windows vajra series or equivalent windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for glass shutter should be of 52 x 25mm with concealed brackets. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy-duty stain less steel pivot hinges shall be provided per shutter. The windows should be panelled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self-expanding, screws. Including 12mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes. |
| 6 | S&Fpowder coated aluminium frame of standard section for doors, windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. |
| 7 | S&F powder coated aluminium window and ventilator shutters , side hung type / sliding without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruber packing , anodised aluminum snap beading , screws, anodised aluminium fittings such as peg stays 150mm long (1nos). hinges type B-21 100mm long (2nos) suitable handle (1nos) complete all as specified and directed by Engineer-in-Charge. |
| 8 | M&L 4mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 sq.m in each pane complete all as specified and directed. |
| 9 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 10 | S&F 4mm thick figured glass, pin head/frostedtype and glazing with oil putty in squares not exceeding 0.50 Sqm each pane complete all as specified and directed by Engineer-in-Charge. |
| 11 | S&F for 30 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shuttercomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary Stainless steel screws shall be paid separately. |
| 12 | S&F for 30 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain wiremesh/skelton door shuttercomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws, complete all as specified and directed. Note: Stainless steel butt hinges and necessary Stainless steel screws shall be paid separately. |
| 13 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm, single or double rebated, comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 14 | S&F for 250 mm long aluminium alloy, anodized, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed withscrews complete all as specified and as directed. |
| 15 | S&F mild steel butt hinges, 100 mm long, medium weight, cold rolledfixed with steel screws or welded to angle iron frame where required complete all as specified and as directed. |
| 16 | S&F 200mmlong aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed. |
| 17 | S&F for 125 mm aluminum handles cast type anodizedcomplete all as specified and directed. |
| 18 | Demolition of brick work built in cement mortar in any position including all quoins, arches & pillars etc complete all as specified and directed. |
| 19 | M&L for brick work withsub class \"B\"bricksstraight or curved on plan exceeding6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 20 | Taking down cement plaster including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed. |
| 21 | Material and labour for rendering 15 mm thick in CM 1:6 on fair faces of brick or concrete surfaces of walls, facia etc to be finishedeven and smooth (w/o using extra cement) complete all as specified and directed. |
| 22 | Material and labour for 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces of walls finished even and smooth w/o using extra Cement complete all as specified and directed. |
| 23 | Supply only integral water proofing compound complete all as specified and directed. |
| 24 | Material and labour for preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with chalk whitening preparatory to distempering on surfaces of walls using mechanical spray machine/method by the authorised applicator of the manufacturer complete all as specified and directed. |
| 25 | M&L for preparation of newly plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer using mechanical spray machine/method by the authorised applicator of the manufacturer complete all as specified and directed. |
| 26 | Dismantling water tanks of capacity exc250 and n exc 500 ltrs and removal to contractor\"s store yard, complete all as specified and directed. |
| 27 | S&F 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I. |
| 28 | Dismantling water tanks of capacity exc500 and n exc 1000 ltrs and removal to contractor\"s store yard, complete all as specified and directed. |
| 29 | S&F 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I |
| 30 | Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removing to store complete all as specified and directed |
| 31 | Supplying and laying of CPVC pipes of bore 15/16 mm, internal dia (equivalent to 15 mm bore GI tube)SDR 11 and plain CPVC SDR 11 fittings in trenches/walls/roof concealed complete all as specified and directed. |
| 32 | Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removing to store complete all as specified and directed. |
| 33 | Supplying and laying of CPVC pipes of bore 20 mm,internal dia(equivalent to 15 mm bore GI tube) SDR 11 and plain CPVC SDR 11 fittings in trenches/roof/walls complete all as specified and directed. |
| 34 | S&F in repairs 15 mm Brass CP central hole basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 35 | S&F in repair 15 mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 36 | S&F in repairs 15 mm Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 37 | S&F in repair for 15 mm bore concealed type chromium plated Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed. |
| 38 | S&F in repair 15 mm bore chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed. |
| 39 | S&F in repair15 mm bore chromium plated Stop angle valves, cast copper alloy screwed pressure, with crutch of butterfly handle,long shank and cup, screwed both ends for iron pipe for unions and fixed complete all as specified and directed. |
| 40 | S&F in repair Brass chromium plated shower rose 125mm size complete all as specified and directed. |
| 41 | S&F in repairpolythene connection of low density polyethylene (LDPE) pipes of pressure rating 2.5 Kgf/Sqcm, 60 cm long with and including two brass union couplings, heavy duty, suitable for 15mm bore pipe, one on each end for connecting polyethylene pipe to GI pipe and fixed complete all as specified and directed. |
| 42 | S&F in repair brass chromium plated tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed. |
| 43 | S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 44 | S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 45 | S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 46 | S&F for 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring, joints,laid in trenches or in floors or fixed to wall including taking down of old unserviceable pipes complete all as specified and as directed. |
| 47 | S&Ffor 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring, joints,laid in trenches or in floors or fixed to wall including taking down of old unserviceable pipes complete all as specified and as directed. |
| 48 | S&F in repair vitreous China squatting pan, `Orissa\" pattern, size 580 x440 mm white, with integral foot rests including provision of cement concrete bedding complete all as specified and directed. |
| 49 | S&F in repair 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe complete all as specified and directed. |
| 50 | S&F in repair coloured composite pattern vitreous china wash down water closet pan (pedestal pattern, Cera model \"Corium-220\" of any colour or equivalent as approved by GE, twin flush systemincluding soft close seat cover all as specified and directed by Engr In Charge. |
| 51 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm , including cutting for and pinning in ends of brackets , including 32 mm dia CP waste waste fitting and PVC waste pipe of required length complete all as spcified and directed. |
| 52 | S&F in repair fancy coloured wash hand pedestal basin size 630x510x180mmcomplete all as erectedby manufacturers instruction shade as approved by GE. Make Cera cat part No. S2040111 or equivalent as approved by GEincluding 32 mm dia CP waste fitting and PVC pipe of required length complete all as specified and directed. |
| 53 | S&F in repair 600 mm x 450 mm polished sheet glass mirror of thickness 5 mm of selected quality glass with PVC moulding all around, mounted on 6 mm thick CWR plywood backing and fixed to wooden/rubber plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr-in-Charge. |
| 54 | Dismantling of stone slab and tilesof any description or thickness in floors, approns etc laid, bedded and pointed in any mortar and removing rubbish off the premises complete all as specified and directed. |
| 55 | Material and labourfor pre polished granite tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting andpolishing types including 20 mm thick bedding layer in CM 1:6 complete all as specified and directed. |
| 56 | Material and labourfor pre-polished granite stone tiles dado 20mm thick machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of mirror finish type including 15 mm thick screed in CM 1 :4 on brick or concrete surface complete all as specified and directed. |
| 57 | S&F in repair sinks with drainage board made of stainless steel sheet 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 58 | Dismantling floor hearth or wall tilling including cement mortat bedding (but not backaing coat) removing serviceable tiles to store & rubbish off the premises complete all as specified and directed. |
| 59 | Material and labourfor Glazed ceramic coloured tiles in vertical surface 450x300x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cm 1:4 on brick or concrete surfaces of wall to receive vertical tiles complete all as specified and directed. |
| 60 | M&L decorative digital type glazed ceramic coloured/highlighter tiles 600mm x 300 mm x 7mm to 8 mm thick in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over 10mm thick rendering in CM 1:4 complete all as specified and directed by Engr-in-Charge. |
| 61 | Material and labour for non skid coloured ceramic dark tiles of size 7-8 mm thick area of each tiles exceeding 0.11 Sqm bur not exc 0.18 Sqm (400x400mm) as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match the shade of tiles over andincluding 20 mm thick screed bed in cm 1:6 complete all as specified and as directed. |
| 62 | Demolition of PCC cement concrete above ground floor and paving n.exc 15 cm thick(below or above ground level) un reinforced complete all as specified and as directed. |
| 63 | Material and labour for 100 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in pavement/plinth protection finished even and fair complete all as specified and directed. |
| 64 | M&L PCC 1:4:8 type D-2 (40mm graded stone aggregate ) for sub base 75mm thick complete all as specified and directed. |
| 65 | Material and labour for vitrified Ceramic tiles 10mm thick Dark shade (Square/ rectangular) polished, area of each tiles n. exc 0.36 SQm in floors etc,, set and jointed in neat cement slurry and pointed in shite or coloured cement to match over and including 20 mm thick screed bed in cm 1:6 complete all as specified and directed. |
| 66 | All as per serial item No 65 above but in vertical surface such as skirting, dado and risers including 10 mm thick rendering in cm 1:4 on brick or concrete surfaces of wall to receive vertical tiles complete all as specified and directed. |
| 67 | Material and labourfor 12mm thick Prelaminated particle board,prelaminated both side with decorative choice laminations, fixed with screws to timber frame work including taking down of old boardcomplete all as specified and directed. |
| 68 | Material and labourfor 18mm thick Prelaminated , board,prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work and fixed in repairs including taking down of old board complete all as specified and directed. |
| 69 | S&F in repairs continuous (piano) hinges mild steel bright finish or electrogalvanised 30mm flaps complete all as specified and directed. |
| 70 | S&F 75mm size brass handles, cast type polished bright complete all as specified and directed |
| 71 | S&F magnatic catch for wooden cabinate shutters complete all as specified and directed |
| 72 | S&F in repairs Harrison rails 25 mm dia mild steel chromium plated curtain rail fixing with brackets stops complete all as specified and directed. |
| 73 | M&L for Complete removal of existing treatment from walls, fins, chajja etc shall include brooming down or steel wire brushing, scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots and removing debris/ malba to low lying area out side of MOD land and applying 3mm thick a layer of Birla white wall care water proof putty on scrapped/uneven surfaces to match with the existing surfaces before application of primer/distemper andapplying two coats of oil bound distemper over a coat of primercomplete all as specified and directed by Engr-in-Charge. |
| 74 | M&L for preparation of old treated plastered surfaces of wall by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt andallloose scales of existing treatment and applying two coats of exterior acrylic emulsion water based (weather proof coat) paint on wall complete all as specified and directed. |
| 75 | M&L for preparation of old treated plastered surfaces of wall by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt andallloose scales of existing treatment and applying twocoat of cement base paint on wall complete all as specified and directed. |
| 76 | Material and labour for preparation of old treated plastered surfaces of ceiling by brooming down or steel wire brushing scrubbing down smoke soot, moulds, moss and efflorescence salts and treating oil and greasy spots removing dust, dirt andallloose scales of existing treatment and applying one coat of oil bound distemper on ceiling using mechanical spray machine/method by the authorised applicator of the manufacturer complete all as specified and directed. |
| 77 | M&L for ATT and providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wallusing chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed. |
| 78 | M&L for ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron |
| 79 | M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 80 | M&L for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6-8mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with chalk and white cement complete all as specified and directed. |
| 81 | S&F in repair PVC (SWR) single socketed rain water pipe 150 mm bore in any length with rubber ring joints fixed towalls/roof incl brackets/clamps etc including taking down of embedded portion in wall including PVC bend and fixing/sealing the samewith suitable water proofingcompound of Fosrok or equivalent as approved by GEcomplete all as specified and directed. |
| 82 | Taking down of old existing roof treatment of any description incl scrube and remove loose concrete, brick tiles, mud fuska, plaster, bitumen, oil grases and any other materials that might effect adhesion by wire brushing the surface and cleaning of the surface up-to mother slab by demolition of existing old padding throughly with water and disposed off old materials from site complete all as specified and directed. |
| 83 | M&L forcement concrete 1:2:4 type B-0 ( using 12.5 mm graded stone aggregate) as inroof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 84 | M&L for 20 mm thick screed bed or bedding layer of mortar in CM 1:4for laying floor finishes as on roof mixed with WPC as per manual at any height complete all as specified and directed.Note : WPC will be measured and paid separately. |
| 85 | Supply only liquid WPC complete all as specified and directed by Engineer-in-Charge. |
| 86 | Preparing and cleaningthe internal surface areas throughly so that they are free from all contaminants like dirt and laitance & to remove all the loose materials by various mechanical means complete all as specified and directed by Engineer-in-Charge. (a)Removal of all surface Imperfections, protrusions, loose concrete & fittings of cracks using SBR later Polymer Modified Mortar in the ratio Cement : Sand (1:4) and 5% by weight of cement. (approx 522 SQM which is 30% of the total 1740 Sqm Roof surface Area).(b)Supplying and applying, Acryllic Based High Performance Elastomeric Waterproof Coating single component Liquid Applied water proofing membrane after applying One primer coat of Sealer coat Acrylic Primer @ 100ml/Sqm and allow the sealer coat to dry for two hrs, Apply first coat of Electrometric Waterproof Coating @ 1.5 Sqm/Lt by roller or brush on the primed surface & allow drying for 4-5 hrs before application of second coat of Electrometric Waterproof Coating@ 1.5 Sqm /Lt. The laying of Liquid applied membrane shall be laid by the authorized & certified applicator of the manufacturer of Membrane. |
| 87 | Taking down carefullyaluminium point wiring (light, Socket or power) completeincluding fittings and fixturessuch as switches, ceiling roses pendents, regulators, sockets etc for taking credit to be measured separetly including making good the disturbed portion/surface. |
| 88 | M&L for point wiring with colour coding multistranded copper conductor cable,PVC insulated and unsheathed size 1.5 sqmm with PVC concealed Conduit (dia not les than 25 mm) with fixing accessories for one light /fan/bell point controlled by one switchwith pressed steel concealed terminal boxes coveredwith 3mm thick laminated sheet incl. contineous earth wire of PVC insulated unsheathed multi stranded copper conductor cablesize 1.5 Sqmm for earth wire connected to common earth dollyall as specified and directed. |
| 89 | All as per item No 88 above but for one3/5 pin socket 5 Amp on same board, with 1.5sqmm wire with 1.5sqmm earth wire. |
| 90 | All as per item No 88 above but for one3/5 pin socket 5 Amp on independent board with 1.5 sqmmwire with 1.5 sqmm earth wire . |
| 91 | All as per item No 88 above but for 3 pins socket outlet 15 Amps independent with 4.0 sq mm incl contineous earthing with multistandred copper conductor PVC insulated unsheathed size 4.0 Sq mm complete all as specified and directed. Note:-(For item 88 to 91 )Cost making good disturbed surface below existing point wiring taken out vide item No 02 and cutting chases and making good of disturbed surfaces by cement & sand mortar (1:3) and surface finish as per adjustment surface conduit and all accessories as required for concealed point wiring vide item No 88 to 91 as applicable shall be deemed to be included in the unit rate quoted against these items. |
| 92 | S&F switch piano flush type 5 Amps, single pole one way 230 Volts , AC completeall as specified and directed by Engr-in-Charge. |
| 93 | S&Fsocket 3/ 5 pins, 6 Amp, flush type piano (multi purpose) 230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 94 | S&F Socket 15 Amps flush type,3/ 6 Pin, 230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 95 | S&F switch15 Amps flush type 230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 96 | S&F Ding Dong door bell230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 97 | S&F Bell push flush type 5 Amps, single pole one way 230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 98 | S&F ceiling rose, PVC / Polycarbonate isolated body ,surface backlite, 65x50mm,three terminals, 230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 99 | S&F stepped type electronic fan regulator flush type 230 Volts , AC complete all as specified and directed by Engineer-in-Charge. |
| 100 | S&FBatten holder PVC/Polycarbonate base / backsuitable for LED lamp. 230 Volts , AC complete all as specified and directed by Engr-in-Charge. |
| 101 | S&F LED Bulbs 9/10W B-22 Pin type 230 Volts , AC completeall as specified and directed by Engineer-in-Charge. |
| 102 | S&F in replacement single pole and neutralsheet metal enclosure with a two pin and earth plug and socket complete with one single pole 20 ampsMCB complete all as specified and directed by Engineer-In-Charge. |
| 103 | S&F LED tube light fittings 20W (4 feet) wall mounted LED batten extruded PVC heat sink provided for efficient heat dissipation & integrated electronic driver optics diffused complete including electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings all as directed by Engineer-in-Charge. |
| 104 | S&FLED 6000K (2’ feet), 10WDecorativeLED lighting fixture with extruded PVC . heat sink, environmental friendly, energy efficient ready to use pack, complete and including taking down existing fittings all as directed by Engineer-in-Charge. |
| 105 | S&F LED bulkhead luminaire 10W decorative type as per sample completeincluding electrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings all as directed by Engineer-in-Charge. |
| 106 | S&F LED building secuity light 25 watt made up of pressure die cast aluminium housing with mid power LED as lightening source and PC cover having top opening inbuilt LED driver with IP66 protection and impact resistance of IK-07 complete including GI bracket with nut bolts, washers etc includingelectrical connection with copper cable from ceiling rose to fittings and including taking down existing fittings all as directed by Engineer-in-Charge. |
| 107 | M&L for submain wiring with 2X4.0 SQMM+1X4.0SQMM Earth Wire single core PVC insulated FRLSHsheathed copper cableconnecting to common earth dolly in and including heavy duty PVC concealedConduitand dismantling and taking down existing unserviceable wiring, all accessories complete all as specified and directed. |
| 108 | M&L for submain wiring with 2X6.0 SQMM+1X6.0SQMM Earth Wire single core PVC insulated FRLSHsheathed copper cableconnecting to common earth dolly in and including heavy duty PVC concealedConduitand dismantling and taking down existing unserviceable wiring, all accessories complete all as specified and directed. |
| 109 | S&F in replacement VTPN 4 way double door prewired distribution board TPN-DPX 125 MCCB including one No MCCB 125 Amps, 25 kA, 4 pole as incomer and suitable SPN/TP MCBs as outgoing double door type sheet metal enclosure 415V with 200 Amps rated standard busbar of suitable size plate and common neutral link without MCBs with blank plate suitable for 4 way complete and including taking down VTPN DB\"s all as specified and all as directed by Engineer-in-Charge.Note : Rates of MCCB and MCB SPN/SP/TP shall deemed to be included in the quoted rates. |
| 110 | S & Fin replacement single pole and neutral sheet metal enclosures for Distribution board (DB\"s)suitable for MCBs fitted with busbar , Neutral link ,Earth Bar and Din rail 240 V, 50 Hz supply double door SP&N DB system 12 ways complete all as specified and dirceted. |
| 111 | S&F MCB SPN 40-63 Amps 240Vincl all termnials, fitting etc. complete all as specified and directed |
| 112 | S&F MCB SP 06 to 40 Amps 240Vincl all termnials, fitting etc complete all as specified and directed |
| 113 | Supply & Fixing ofMeter box sheet metal enclosure concealed type made of metal of size 32 x 25 x 14 cm having suitable incoming and outgoing openings for cables complete all as specified and as directed by Engr-in-Charge |
| 114 | M&L for Refixing carefully serviceablefans / geysers etc any typefromsite on completion of civil and E/& M works incl making necessary connection with suitable copper wire and testing and incl taking down complete all as specified and directed by Engr-in-charge. |
| 115 | M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick burried directly in gorund (earth pit not less than 2.25 Mtr normal ground level),and top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanisedmeans of earth wire 4 mm dia with bolts, nuts & check nuts, and washers of galvanised iron protection pipe light grade of 15 mm dia and watering pipe medium grade of 20 mm dia and filled with alternate layer of charcoal and common salt, watering funnel with wire mesh, earth pit chamber and cover CI frame PCC 1:3:6 type C-2 all as shown in electrical plate No-3 of SSR part-I of 2009 connected to earthing test point all as specified and indicated including all earth work excavation, returning filling and disposal of surplus soil and testing on completion incl taking out old u/s earthing material complete all as specified and dirceted. |
| 116 | Net Contract Sum will be after deducting Sch of Credit of Rs 1,78,336.00 |
