|
| 1 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 2 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 3 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 4 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 5 | Of area 3 sq. metres and below |
| 6 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead: |
| 7 | Of sectional area 40 square centimetres and above |
| 8 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 9 | For thickness of tiles 10 mm to 25 mm |
| 10 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 11 | Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 12 | All kinds of soil |
| 13 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 14 | 1:4:8 (1Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 15 | 1:2:4 (1cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 16 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 18 | Foundations,footings,basesof columns,etc.formass concrete |
| 19 | Shelves (Cast in situ) |
| 20 | Lintels,beams,plinthbeams,girders,bressumersand cantilevers |
| 21 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level. |
| 22 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 23 | 12 mm cement plaster of mix: |
| 24 | 1:4(1 cement: 4 fine sand) |
| 25 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 26 | Providingand fixingplainmultipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 27 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000 |
| 28 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 29 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 30 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approvedbrandandmanufacture,includingapplyingadditionalcoats wherever required to achieve even shade and colour. |
| 31 | Two coats |
| 32 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: |
| 33 | New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 34 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 35 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 36 | All kinds of soil. |
| 37 | Providing and laying in position specified grade of reinforced cement concrete,excludingthecostofcentering,shuttering,finishingand reinforcement - All work up to plinth level: |
| 38 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 39 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 40 | Ingratings,frames,guardbar,ladder,railings,brackets, gates and similar works |
| 41 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 42 | Providing and fixing bolts including nuts and washers complete. |
| 43 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 44 | Electric resistance or induction butt welded tubes |
| 45 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 46 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: |
| 47 | Two or more coats on new work |
| 48 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 49 | G.S. Sheet |
| 50 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite)soliddoor/window/Clerestorywindows&otherFrames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A categorywithpropertyofbeingtermite/borerproof,water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and lengthcomplete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.edepth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 51 | Frame size 45 x 70 mm |
| 52 | Frame size 65 x 100 mm |
| 53 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimumcompressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 54 | 30 mm thick |
| 55 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVCfoil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprisingof virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread offlame of Class Acategory with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.(Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) |
| 56 | 25 mm thick |
| 57 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanizedmild steel section madeof requiredshape & size asper CPWDSpecification,uPVC extrudedglazingbeads,interlocksandlnlinesashadaptor(where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum8mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:-StructuraldesignproofcheckedfromaGovernment Engineering Institute,tobeprovidedbythemanufacturerfor (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds |
| 58 | Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (40 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre). |
| 59 | Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre). |
| 60 | Fixed window/ ventilator with mullion /transom.Using R1 series with frame (33 mm & above) x (35 mm & above) & mullion (33 mm & above) x (50 mm & above). (Height upto 0.90 metre) |
| 61 | Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 62 | Providingandfixing 18mmthickgangsawcut,mirrorpolished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters,window sills,facias andsimilar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 63 | Granite stone slab of colour black, Cherry/Ruby redArea of slab over 0.50 sqm |
| 64 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 65 | Granite work |
| 66 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : |
| 67 | 20 mm dia (heavy type) |
| 68 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 69 | 300x10 mm |
| 70 | 150x10 mm |
| 71 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 72 | Twin rubber stopper |
| 73 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing andmakingcurvature(wherever required)andfittingthesame with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 74 | Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 75 | Glazed vitrified floor tiles polished finish of sizeSize of Tile 600 x 1200 mm |
| 76 | Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 600 x 600 mm |
| 77 | ProvidingandlayingVitrified tilesindiferent sizes (thickness tobe specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). |
| 78 | Size of Tile 600x600 mm |
| 79 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 80 | Kitchen sink without drain board610x460 mm bowl depth 200 mm |
| 81 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 82 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 83 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 84 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 85 | Providing and placing on terrace (at all floor levels) polyethylene water storagetank,IS : 12701marked,withcoverandsuitablelocking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 86 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 87 | 15 mm nominal bore |
| 88 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: |
| 89 | 150mm |
| 90 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 91 | 15 mm nominal bore |
| 92 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 93 | 300x16 mm |
| 94 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 95 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 96 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 97 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 98 | 20 mm nominal dia Pipes |
| 99 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 100 | 25 mm nominal dia Pipes |
| 101 | 40 mm nominal dia Pipes |
| 102 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 103 | 45 cm length15 mm nominal bore |
| 104 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 105 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 106 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approvedmake500mmlongwithscrewsetc. complete as per direction of Engineer- in-charge, |
| 107 | Providingand fixingready made304 grade stainless steelModular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirementincludingfinishing (wherever required)andfittings.The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in- charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) |
| 108 | Providing and laying matt finished vitrified tile of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 109 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of Stone Aggregate 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 110 | Providing cement concrete surface drain including earthwork excavation 10 cm thick base concrete and 15 cm thick side wall with 1:3:6 ( 1 cement : 3 Coarse sand: 6 graded stone aggregate of 40 mm nominal size) cement concrete finished with 1:4 (1 cement : 4 sand) a floating coat of neat cement inside the drain and its top and exposed surface including earthwork in excavation and disposed of surplus earth etc. |
| 111 | 15 X 15 cm Surface drain |
| 112 | Providing and laying hollow cement concrete block walling 100mm thick consisting hollow block of size 400 x 100x200mm of mix 1:3:6(1cement :3 coarse sand:6 graded stone agg. 10mm nominal down size) having a crushing strength of 3.5N/mm2 at 28 days as per I.S. 2185 (Part-I) 1979 laid in cement mortar 1:6(1cement : 6 coarse sand). |
| 113 | Upto floor five level |
| 114 | Providing and laying hollow cement concrete block walling 200mm thick consisting hollow block of size 400 x 200x200mm of mix 1:3:6(1cement :3 coarse sand:6 graded stone agg. 10mm nominal down size) having a crushing strength of 3.5N/mm2 at 28 days as per I.S. 2185 (Part-I) 1979 laid in cement mortar 1:6(1cement : 6 coarse sand). |
| 115 | Upto floor five level |
| 116 | Providing and fixing 4 mm dia. G.I. wire for adjusting hangers (upto 3000mm length), fixed to roof roof truss frames by tieing at both ends, complete as per direction of Engineer-in-charge. |
| 117 | Providing and fixing C.P Health Faucet with 01 mtr long C.P flexible tube in crome finish and fixing on wall hook etc. all complete as per the direction of Engineer-in-charge. |
| 118 | 15 mm nominal dia |
| 119 | Providing and fixing C.P soap dish with wall flange of std size of approved quality Make: Jacquard or equivalent as per the direction of Engineer –in charge. |
| 120 | 150mm x 150mm |
| 121 | Providing and fixing C.P towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 122 | Providing and fixing C.P brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 123 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 124 | Providing and fixing C.P Towel rack (heavy duty) of superior quality all complete as per direction of Engineer-in-charge. |
| 125 | Size 0.60x0.25mm |
| 126 | Providing and fixing pre-painted galvalume (PPGL) steelprofile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping aluminium screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 127 | Providing and fixing pre-painted galvalume (PPGL) steelprofile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd. or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with aluminium zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling /self tapping aluminium screws complete |
| 128 | Pre-painted galvalume (PPGL) Steel Ridges plain (500 - 600mm) |
| 129 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 130 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 131 | Providing and fixing C.P. two way angular cock (Jaquar or equivalent) of approved quality. |
| 132 | 15mm nominal bore |
| 133 | Providing and fixing uPVC trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 134 | 110mm inlet and 75mm outlet |
| 135 | Providing and fixing in position eaves or facia board with 18mm thick 30cm wide WPC Solid board including fixing with nuts and bolts etc, all complete as per the direction of Engineer-in-charge. |
| 136 | Providing and fixing CP brass sawn neck bib cock of approved quality (Jaquar of equivalent make). |
| 137 | 15 mm nominal bore |
| 138 | Providing and fixing ball valve (CPVC) of approved quality, High or low pressure, with plastic floats complete: |
| 139 | 20mm nominal bore |
| 140 | 25mm nominal bore |
| 141 | 40 mm nominal bore |
| 142 | Providing and fixing 15 cm wide, 45 cm overall semi-circular PPGL sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. |
| 143 | 0.50mm thick PPGL sheet. |
| 144 | Providing and fixing soil, waste and vent pipes: with UPVC pipe coforming to IS:13592 type B including jointing of pipes and fitting with solvent cement etc complete as per direction of Engineer-in-charge. |
| 145 | 110mm dia |
| 146 | 75mm dia |
| 147 | Providing and fixing uPVC moulded plain bend of required degree for uPVC soil pipes conforming to IS:13592 type \"B\" including jointing with seal ring conforming to IS: 5382 living 10mm gap for thermal expansion etc. |
| 148 | 110 mm UPVC Plain bend |
| 149 | 75mm UPVC plain bend |
| 150 | Providing and fixing 18mm thickHigh density high moisture resistance (HDHMR)board \"A\"grade of approved brand and shade make Action Tesa or equivelent with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter including stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws etc all complete as per direction of Engineer-in-charge |
| 151 | Extra for providing and fixing wind ties of 40x 6mm flat aluminium section. |
| 152 | Providing & fixing glass panes with silicon sealentin UPVC doors, windows, clerestory windows, all complete with: |
| 153 | 5.5 mm thick glass panes |
| 154 | Providing and fixing C.P brass bath mixer of superor quality (Jaquar or equavalent) etc, all complete as per the direction of Engineer-in-charge. |
| 155 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to UPVC window Shutter etc,all complete as per directions of Engineer-in-Charge. |
| 156 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 157 | 150 mm diameter |
| 158 | Renovation of IEI. |
| 159 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor singlecorecableinsurface /recessedmediumclassPVC conduit,with Modulartypeswitch, suitable size plastic switch board and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required |
| 160 | Group-B |
| 161 | Wiring for Light/ power plug wiring with 2 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 162 | Wiring for Circuit/ sub mainWiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. |
| 163 | 2x1.5 sq.mm + 1x1.5 sq.mm. earth wire |
| 164 | 4X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 165 | Supplying and fixing following size/ modules, Plastic surface Box along with modular base & cover plate for modular switches in recess etc. as required. |
| 166 | 2 Module |
| 167 | 3 Module |
| 168 | 6 Module |
| 169 | Supplying and fixing following modular switch/ socket, ISI marked on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 170 | 6A 1 Way Switch, 1M |
| 171 | 6 A 2in 1 Socket , 2M |
| 172 | 16A 1 Way Switch, 1M |
| 173 | 6A/16A , Twin Socket, 2 M |
| 174 | Supplying and fixing two module stepped type electronic fan regulator on theexisting modular plate switch box including connections but excluding modular plate etc. as required. |
| 175 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box / wooden block including connection etc as required. |
| 176 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 177 | SITC of energy saving 1200mm, BLDC 5 star Ceiling fanwith maximum power consumption of 32 W( (Make: Crompton, Model: Energion Riviera (Without remote) or equivalent)). |
| 178 | SITCofexhaust fan of 200 mmsweep (PVC Body ) (Make : Crompton, Model: Brisk air neo/Brisk Air Plus or equivalent)in the existing opening, including making good the damage, connectionsetc. as required. |
| 179 | SITCofexhaust fan of 300 mm. sweep (Metallic ) (Make : Crompton, Model: Drift Air Plus Metal or equivalent)in the existing opening, including making good the damage, connectionsetc. as required. |
| 180 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. |
| 181 | Supplying and Fixing PVC Button / Angle Holder including connection etc as required. |
| 182 | Supplyingand fixing10 W LED Bulkheadwith PDC housing having IP65/IP66 Protection (Make:Bajaj,Model : Wee Plusorequivalent). |
| 183 | Supplying and fixing following LED lamps (CDL/WW)on the existing lamp holder: |
| 184 | 9W, B22/E27 ( Make : Havells or equivalent ) |
| 185 | Supplying and fixing following way, horizontal type three pole and neutral, sheetsteel, MCB distribution board, 415 volts, on surface/ recess, complete with tinnedcopper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator |
| 186 | 6 way (8 + 18), Double door |
| 187 | Supplying and fixing 5 A to 32 A rating,240/415 V, 10 kA \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 188 | Single Pole |
| 189 | Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required |
| 190 | 63 A |
| 191 | Supplying and fixing of 1\", 5 W LED batten(integrated),( Make: Philips,Model AstraLine or equivalent ). |
| 192 | SITC of LED Retrofit TubeBatten havingSingle Side Connection(Make: Luker, Product Code:LLTS1NSorequivalent ) with one number 4 feet, 20W LED Tube lampwith PC body having minimum efficacy of 100 lm/w (Make:Luker, Product Code:LTP820Norequivalent)directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 193 | Supplying & fixing of Modular AC Box with 20 A DP MCB in plastic enclosure & Unbreakable Heavy Duty with ISI Plug Topincluding connections etc. as required (Make : Anchor, Code : 98492 or equivalent). |
| 194 | Supplying, installation, testing and commissioning of 15 litres/ 2 KWStorage Water Heater,5 star rated, ISI marked (Make:Havells, Model: Fabia,Product Code: GHWAFATIB015 or equivalent)complete with suitable heavy duty water connection pipe etc. as required. |
| 195 | Earthing with ASHLOK make SEE brand Safe Earthing Electrode, Type- 19, 48 mm dia., length 2.00 mtrs. or equivalent by filling inner space withtotal50 Kg(2 bags) Electrodite (Back Fill Compound ) required for safe earth electrode and providing masonary enclosure with C.I. cover plate having locking arrangement etc.as required. |
| 196 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 197 | 20 mm |
| 198 | Providing & laying earth connections from earth electrode with 4 mm dia copper wire in 15mm dia GI pipe from earth electrode includingconnetion with copper thimble excavation and re-fillingas required. |
| 199 | Providing and fixing of 4mm diameter copper wire on surface or in recess for loop earthing along with the existing surface recesses conduit/ submain wiring/ cable etc. as required. |
