|
| 1 | Dismantling of plain or corrugated Asbestos sheeting, any gauge, thickness, including Nainital or similar pattern in roof covering. |
| 2 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 3 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,ridges, etc., fixed with self tapping screws as specified |
| 4 | S&F Plain galvanised, mild steel sheeting of 0.63mm thick as, in ridges, hips, valley gutters, drip and straight / stepped flashings (length and girth) as fixed with nail complete all as specified. |
| 5 | M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 6 | M&L for preparation of old painted steel surfaces of any description, n exc 10 cm in width or girth, not otherwise described when unconnected with other painting or when painted in a different tintand applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 7 | M&L for preparation of New painted steel surfaces of any description, n exc 10 cm in width or girth, not otherwise described when unconnected with other painting or when painted in a different tintand applying Two coat of synthetic enamel paint over a coat red oxide primer complete all as specified and as directed. |
| 8 | S&F for Mild steel section of flat iron fillets as in wind ties for roof sheet including drilled, securing bolt to flat iron fillets etc and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed. |
| 9 | Demolition of brick work or stone / boulder masonry,built in cement or lime mortar including all quoints, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete. |
| 10 | M&L for sub class \"B\" Brick built in CM 1:6, straight or curved on plan exc 6m mean radius on plan ,complete all as specified and directed. |
| 11 | M&L for sub class \"B\" bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4,complete all as specified and directed. |
| 12 | Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc,complete all as specified and directed. |
| 13 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1 : 6 and finishing even and smooth without using extra cement,complete all as specified and directed. |
| 14 | M&L for rendering 15mm thick in CM (1:4) on other then fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement mixed with WPC @ 3 % by the weight of cement used complete all as specified and directed. (WPC will be paid separately as supply only) |
| 15 | Supply only water proofing compound ,complete all as specified and directed. |
| 16 | M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1mm thickwall care putty birla white or JK & over one coat of chalk whiting priming paint complete. |
| 17 | Dismantling timber scantling 40 sq.cm and over in section and in any position in unframed work complete all as specified and directed. |
| 18 | M&L 2nd class hardwood, scantling, wrought, timber fixed with nails, complete all as specified and directed. |
| 19 | M&L for preparation of new wooden surface any description not otherwise described and exc 10 cm width or girth applying two coats of synthetic enamal paint over acoat of pink primer complete all as specified and diected. |
| 20 | Demolation of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed. |
| 21 | M&L for GI wire netting of 0.90mm dia and 12mm mesh lathing to wood or metal studding, joist, etc in walls, ceilings etc including all laps , cutting and waste fixed with tinned tacks of wire staples etc complete all as specified and directed. |
| 22 | M&L for rendering 15mm thick on one side of lathing in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement all as specified and directed. |
| 23 | M&L for rendering 10mm thick on other side of lathing in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement all as specified and directed. |
| 24 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over one coat of alkali-resistant priming paint complete all as specified and directed. |
| 25 | M&L for preparation of old decorative wall surfaces and applying two coats of cement base paintcomplete all as specified and directed. |
| 26 | M&L for preparation of old decorative wall surfaces and applying two coats of Distemper complete all as specified and directed. |
| 27 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed. |
| 28 | M&L for non skid ceramic coloured glazedtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed. |
| 29 | M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. |
| 30 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness , including cover fillets complete all as specified and directed. |
| 31 | S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frameincluding providing two coats of white wash complete all as specified and as directed. |
| 32 | M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed |
| 33 | Forming Construction joint 30mm deep x10mm wide filled with sealing compound, Grade ‘A’ complete all as specified and directed. |
| 34 | M&L for Cement concrete 1 : 3 : 6 type C2, as in surface channels and drains (using 40mm graded aggregate) including necesssary form work for sides |
| 35 | Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed. |
| 36 | M&LPlain cement concrete 75mm thick type C-2, 1 : 3 : 6 (using 40mm graded stone aggregate) as in sub-base to receive floor finishes of path etc complete all as specified and directed. |
| 37 | M&L Chequered cement concrete tile 30mm x 30mm x 19 to 20 mm thick with grey cement and pigment set, jointed and pointed in neat cement slurry over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed. |
| 38 | Taking down wooden Chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each butincluding builders hard ware complete. |
| 39 | Taking down wooden Chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sq. m but n exc 4 sq. m including builders hard ware complete. |
| 40 | S&F 35mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,with particle board core one face is covered with deco rative face veneer with lipping/frame to match complete al as specified and directed |
| 41 | S&F 35mm thick skeliton/gauged shutter open rebated and prepared to recive glass gauged etc (with sash bars) edge of framingg plain,chamfered or rounded, fitted with cut mitred beads for securing glass, etc sizes of members of shutters as specified in SSR part I,Section 8, clause 8.24(a), supplied and fitted to chowkats. |
| 42 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainlesssteel wire staples in window and door including wooden bids as fixed in repair as old door/window complete all as specified and directed. |
| 43 | Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed.(i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v)Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. |
| 44 | Supply & fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 45 | S&F powder coated aluminium anodised frame for doors, windowsetc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 46 | S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including all necessary fittings like hinges joining cleats, glazing clips,moving roller, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 47 | S&F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed. |
| 48 | Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:3) & painted with white or coloured paint complete all as specified and as directed |
| 49 | M&L Butt hinges med weight cold rolled mild steel and fixed 100mm size complete all as specified and directed. |
| 50 | M&L 300mm long Aluminium alloy, anodised, sliding door bolt with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy and fixed complete all as specified and directed. |
| 51 | S&F Aluminium anodised barrel tower bolt of extruded section and fixed 150 mm long complete all as specified and directed. |
| 52 | S&F Aluminium alloy handles, extruded, fabricated type, anodised 150mm size complete all as specified and directed. |
| 53 | S&F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor 140mm size neccesary screws completecomplete all as specified and directed. |
| 54 | S & F for Anodisied aluminium alloy harrison rails, mild steel , chromium plated with fixing bracket , stops, roller etc complete all as specified and directed. |
| 55 | Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge. |
| 56 | Taking down carefully MCB DBs any type and size by unscrewing from main switch boards/cut out boxes and removing materials to store for keeping in safe custody for reuse at site or for taking credit including sealing the cable ends and making good disturbed surface of wall etc as per existing finishes complete all as specified and directed. |
| 57 | Material and labour for point wiring for one light/fan point controlled by one, one way switch with 1.5 Sqmm single core, PVC FRLSH insulated unsheathed, multistranded copper conductor drawn through and includingPVC casing caping including necessary accessories like bends, tees, PVC square and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLSH insulated unsheathed multi stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of 1.2mm thickness with plastic laminated white top sheet cover 3mm thick.(Note:-(1) Rate forCutting, chieseling and making good the existingsurface for complete concealed wiring is deemed to be included in quoted rate) all as specified & directed. |
| 58 | All as per item No 3 but point One 3 Pin 5 Amps socket out let point onindependentboard. |
| 59 | All as per item No 3 but One 3 Pin 5 Amps socket out let point on same board alongwith other suitable switchs. |
| 60 | All as per item No 3 wiring point here-in-before but using 4 sqmm PVC FRLSH insulated copper condutor wire for connecting 15A socket on independent board complete all as specified/directed. |
| 61 | Supply and fixing of switch piano flush type 240 Volts 5 Amps, SP, one way complete all as specifed/directed. |
| 62 | Supply and fixing of switch socket combination 3/5 Pin, 2 in 1, 5 Amps, 240 volts flush type (non shuttered) complete all as specified/ directed. |
| 63 | Supply & fixing of socket outlet 2 in 1, 3/5 pin 5 Amps, 240 Volts,flush type (non shuttered) complete all as specified / directed. |
| 64 | Supply and fixingof switch socket out let combination multipurpose 3/5 pin, 15/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) complete all as specified/directed. |
| 65 | Supply and fixing angular/batten holderPVC/Polycarbonate suitable for batten fittings including one inverter LED Lamp of 9W of Havells/Philips/Cromton Make, complete all as specified/directed. |
| 66 | Supply and fixing ofceiling rose surface PVC/Polycarbonate, 65x50 mm two to three terminals complete all as specified/directed. |
| 67 | Supply and fixing Inverter type LED batten(1.2m) made of CRCA sheet housing with 4hrs battery backup PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumenat a minimumsystem efficiency of 115 lumen per watt and total power consumption not more than 18/20 W iincluding driver. It has a rated system life time more than 15000 burning hour at L70 and should have a colour temperature of 6500K, CR>80 , THD < 10 % and PF>0.95 complete all as specified and as directed. make: Phillips , Crompton , Havells or equivalent. |
| 68 | S&F LED light fitting invrter type with high ouput diffuser 2 feet, 10 watts 220 volts AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable of suitable size. |
| 69 | Supply and fixing LED Bldg light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete withIP 65/66 protection complete as specified/directed. |
| 70 | S&F Bldg light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtrcomplete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed. |
| 71 | Supply and fixing of recess mounted LED flat panel 2 x 2made of CRCA sheet steel housing duly powdercoated with high efficient LEDs & glare free full opal diffuser with lumen output of 4000-4500 with life span of more than 25000 hr, including all other accessories ,IP-20including testing and commissioning including testing completedas specifed/directed. |
| 72 | Supply and fixing in repair of MCB Distribution board SPN 8 Way for mountingSPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed by Engr-in-charge. |
| 73 | Supply and fixing 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP,DP in the MCB DB Complete with connection testing and commissioning. |
| 74 | Supply & fixing in repair of MCB SP 6-32 Amps\"C\" Series 10 KA, 240 volts complete all as specified/directed. |
| 75 | Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing lead by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and eath works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and directed.Note:No extra payment will be for the earthing GI wire of size 4 mm dia all complete as directed/specified. |
| 76 | Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC casing caping of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through PVC Conduit and connected common earth dolly including taking out the old sub main wiringfor connection to DBs/dolly shall be deemed to be included in this item and Two runs of 6 Sq mm as current carrying conductor and one run of6 Sq mm as earth conductor PVC conduit shall be measured as one run for measurement, complete all as specified and directed. |
| 77 | Taking down and Supply and laying and testing cable, XLPE insulated,screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables(heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sq mm 2 core complete all as specified/directed. |
| 78 | Excavating in Trenches not exc. 1.50 mtr wide and not exc. 1.50 mtr in depth, Taking Out and Laying of Cables, etc. and getting out in Soft/ Loose Soil, complete all as specified and as directed. |
| 79 | Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 250mm in Soft/Loose Soil, complete all as specified and as directed. |
| 80 | Removing excavated Materials (Soils) not exc. 50.00 mtr and depositing where directed at a level not exc. 1.50 mtr above the Starting Point in Soil, complete all as specified and as directed. |
| 81 | M&L Sand Cushioning (dry) in Trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thick -ness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. |
| 82 | S&F LT cable cover Class LV, Type I, flat, size 250 mm x 150mm x 40mm, well burnt, laid breadth-wise along the axis of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed. |
| 83 | Boring under without disturbing the top surface of the road for passing through GI protection pipe 50mm bore, not exceeding 10m in single length complete all as specified and as directed. Note: Necessary infrastructure required for boring shall be arranged by the contractor at his own cost. |
| 84 | Dismantling of plain or corrugated Asbestos sheeting, any gauge, thickness, including Nainital or similar pattern in roof covering. |
| 85 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 86 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall,ridges, etc., fixed with self tapping screws as specified |
| 87 | S&F Plain galvanised, mild steel sheeting of 0.63mm thick as, in ridges, hips, valley gutters, drip and straight / stepped flashings (length and girth) as fixed with nail complete all as specified. |
| 88 | M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 89 | M&L for preparation of old painted steel surfaces of any description, n exc 10 cm in width or girth, not otherwise described when unconnected with other painting or when painted in a different tintand applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 90 | M&L for preparation of New painted steel surfaces of any description, n exc 10 cm in width or girth, not otherwise described when unconnected with other painting or when painted in a different tintand applying Two coat of synthetic enamel paint over a coat red oxide primer complete all as specified and as directed. |
| 91 | S&F for Mild steel section of flat iron fillets as in wind ties for roof sheet including drilled, securing bolt to flat iron fillets etc and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed. |
| 92 | Demolition of brick work or stone / boulder masonry,built in cement or lime mortar including all quoints, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete. |
| 93 | M&L for sub class \"B\" Brick built in CM 1:6, straight or curved on plan exc 6m mean radius on plan ,complete all as specified and directed. |
| 94 | M&L for sub class \"B\" bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4,complete all as specified and directed. |
| 95 | Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc,complete all as specified and directed. |
| 96 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1 : 6 and finishing even and smooth without using extra cement,complete all as specified and directed. |
| 97 | M&L for rendering 15mm thick in CM (1:4) on other then fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cementWPC @ 3 % by the weight of cement used complete all as specified and directed. (WPC paid in seprate item supply only) |
| 98 | Supply only water proofing compound ,complete all as specified and directed. |
| 99 | M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1mm thickwall care putty birla white or JK & over one coat of chalk whiting priming paint complete. |
| 100 | Dismantling timber scantling 40 sq.cm and over in section and in any position in unframed work complete all as specified and directed. |
| 101 | M&L 2nd class hardwood, scantling, wrought, timber fixed, complete all as specified and directed. |
| 102 | M&L for preparation of new wooden surface any description not otherwise described and exc 10 cm width or girth applying two coats of synthetic enamal paint over acoat of pink primer including anti termite treatment complete all as specified and diected. |
| 103 | Demolation of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed. |
| 104 | M&L for GI wire netting of 0.90mm dia and 12mm mesh lathing to wood or metal studding, joist, etc in walls, ceilings etc including all laps , cutting and waste fixed with tinned tacks of wire staples etc complete all as specified and directed. |
| 105 | M&L for rendering 15mm thick on one side of lathing in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement all as specified and directed. |
| 106 | M&L for rendering 10mm thick on other side of lathing in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement all as specified and directed. |
| 107 | M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint including and over one coat of priming plastered and other surfaces with alkali-resistant priming paint complete all as specified and directed. |
| 108 | M&L for preparation of old decorative wall surfaces and applying two coats of cement base paint including and over one coat of priming plastered and other surfaces with alkali-resistant priming paint complete all as specified and directed. |
| 109 | M&L for preparation of old decorative wall surfaces and applying two coats of Distemper over a coat of white primer etc complete all as specified and directed. |
| 110 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed. |
| 111 | M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed. |
| 112 | M&L for ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. |
| 113 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness , including cover fillets complete all as specified and directed. |
| 114 | S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frameincluding providing two coats of white wash complete all as specified and as directed.Make of E-Board : Eternit Everest / Lafarge/ Armstrong/Visaka Industries Ltd. |
| 115 | M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed |
| 116 | Forming Construction joint 30mm deep x10mm wide filled with sealing compound, Grade ‘A’ complete all as specified and directed. |
| 117 | M&L for Cement concrete 1 : 3 : 6 type C2, as in surface channels and drains (using 40mm graded aggregate) including necesssary form work for sides |
| 118 | Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed. |
| 119 | M&LPlain cement concrete 75mm thick type C-1, 1 : 3 : 6 (using 40mm graded stone aggregate) as in sub-base to receive floor finishes of path etc. |
| 120 | M&L Chequered cement concrete tile 30mm x 30mm x 19 to 20 mm thick with grey cement and pigment set, jointed and pointed in neat cement slurry over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes |
| 121 | Taking down wooden Chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each butincluding builders hard ware complete. |
| 122 | Taking down wooden Chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sq. m but n exc 4 sq. m including builders hard ware complete. |
| 123 | S&F 35mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,with particle board core one face is covered with deco rative face veneer with lipping/frame to match complete al as specified and directed |
| 124 | S&F 35mm thick skeliton/gauged shutter open rebated and prepared to recive glass gauged etc (with sash bars) edge of framingg plain,chamfered or rounded, fitted with cut mitred beads for securing glass, etc sizes of members of shutters as specified in SSR part I,Section 8, clause 8.24(a), supplied and fitted to chowkats. |
| 125 | S&F stainless steel with cloth 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainlesssteel wire staples in window and door including wooden bids as fixed in repair as old door/window complete all as specified and directed. |
| 126 | Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed.(i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v)Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. |
| 127 | Supply & fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 128 | S&F powder coated aluminium anodised frame for doors, windowsetc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 129 | S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including all necessary fittings like hinges joining cleats, glazing clips,moving roller, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 130 | S&F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed. |
| 131 | Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:3) & painted with white or coloured paint complete all as specified and as directed |
| 132 | M&L Butt hinges med weight cold rolled mild steel and fixed 100mm size. |
| 133 | M&L 300mm long Aluminium alloy, anodised, sliding door bolt with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy and fixed. |
| 134 | S&F Aluminium anodised barrel tower bolt of extruded section and fixed 150 mm long |
| 135 | S&F Aluminium alloy handles, extruded, fabricated type, anodised 150mm size. |
| 136 | S&F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring fixed in floor 140mm size neccesary screws complete. |
| 137 | S & F for Anodisied aluminium alloy harrison rails, mild steel , chromium plated with fixing bracket , stops, roller etc complete all as specified and directed. |
