|
| 1 | Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. orfor shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified. |
| 3 | M&L for removing excavated soilsexc. 500mn.exc1.5 kmcomplete all as specified. |
| 4 | Demolition of brickwork built in cement mortar including all quoins ,arches ,pillars etc complete all as specified and directed. |
| 5 | M&L for brick work with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified. |
| 6 | M&L for Brickwork with subclass‘B’ bricks, straightor curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified. |
| 7 | M&L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified. |
| 8 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engr-in-Charge. |
| 9 | S&F for 2mm thick fibre glass reinforced translucent plain sheeting fixed with coach screw and washer in roof, wall etc. complete all as specified. |
| 10 | S&F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified. |
| 11 | S&F Pre-Painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall,fixed with self tapping screws complete all as specified. |
| 12 | S&F 8 mm thick Polycarbonate reinforced coloured plain sheeting fixed with coach screws and washers in roofs,vertical surfaces etccomplete all as specified and directed by Engr-in-Charge. |
| 13 | Supply only Chain link MS galvanisd fencing, any size or type. |
| 14 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire etc complete all as specified and directed. |
| 15 | Restriainingresecurigincluding making good staples or tighting of cross wire galvanised barbed wire in any dia of wire or any spacing all as specified and directed by Engr-in-Charge. |
| 16 | S&F in repair Galvanised. 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails strain-ing bolts,including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins , etc, as directed (each line wire to be measured) complete all as specified. |
| 17 | S&F in repair 950/650/450 mm dia (as directed by Engr-in-Charge) concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coilall as specifiedand directed by Engineer–in-Charge |
| 18 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 19 | S&F for Mild steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 including cutting etc complete all as specified.including dismantling of existing truss. |
| 20 | M&L for steel gate Ornamental type/Grill work including hold fasts, pintels, stoppers running rails, bushes and all as CI decorative pieces, locking arrangement etc complete all as per design approved and as directed by Engr-in-charge work conforming to Fe-410-O etc complete. |
| 21 | S&F for MS as in postsand struts in fencing angle including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement all as specified and directed by Engr-in-Charge. |
| 22 | Expanded metalweight n .exc 4 kg/sqm , cut to length, Bent to shape required incl welding and tying with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified. |
| 23 | M&L preparation of new steel surface and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 24 | Demolition of cement concrete in ground floors of any description and in any position not otherwise specifically provided(un reinforced) complete all as specified. |
| 25 | M&L 75mm thick cement concrete 1:3:6type B2 using 40mm graded stone aggregate as in plinth/sub base. Complete all as specified. |
| 26 | M&L 100mm thick cement concrete 1:3:6type B2 using 40mm graded stone aggregate as in plinth/sub base. Complete all as specified. |
| 27 | M&L for coloured chequered Cement concrete tile glazed finish 300mmx300mmx25mm ,machine pressed; set jointed and pointed in neat cement slurry in floors, with grey cement and pigments laid over 15 mm thick screed be in CM 1:6 complete all as specified. |
| 28 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 29 | M&L for hard core using broken stone or boulders of gauge not exc 63mm, deposited, spread, levelled, watered and well rammed to a true surface,complete all as specified and directed by Engineer-in-Charge. |
| 30 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc |
| 31 | M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces (Cement plaster 1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 32 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (Cement plaster 1:4) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 33 | M&L forrendering 5 mm thick plaster inCM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 34 | M&L for preparation of newly plastered surfaces of wall and applaying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification over one coat of primer and Providing and applying plaster of paris putty of 1mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 35 | M&L for preparation of newly plastered surfaces of ceiling and applaying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification over one coat of primer and Providing and applying plaster of paris putty of 1mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 36 | M&L for preparation of newly plastered surfaces of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces inculding Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 37 | M&L for complete removal of existing treatment on old surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces inculding Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 38 | M&L for complete removal of existing treatment on old surfaces of wall and applaying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification over one coat of primer and Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 39 | M&L for complete removal of existing treatment on old surfaces of ceiling and applaying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification over one coat of primer and Providing and applying plaster of paris putty of 1mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and as directed. |
| 40 | M&L Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete. |
| 41 | Demiolition of stone slab and tiles of any description or thickness in floors, wall ,aprons laid bedded and pointed in any mortar. |
| 42 | M&L Dholpur Red stone 20 to 25mm thick any size with one side polished on walls ,chjja , straight courses, laid and jointed in cement and stone dust mortar 1:3, recess pointed (10mm x 20mm) with an admixture of white cement and Dholpur stone dust 1:1 complete all as specified and as directed by engineer-in-charge. |
| 43 | M&L for 18 to 20mm thick granite slab (table rubbed and polished) as in steps, jambs, pillars, window cills cooking platform and the like, bedded and jointed in cement mortar 1:4 and pointed with white cement with admixture of pigment to match with shape of Granite laid over and includingbedding layer of 15mm thick cement mortar 1:4 complete all as specified and as directed. |
| 44 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 45 | M&L for coloured Glazed ceramic tiles in vertical surface 450x300X7mm or 600X300X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match on 15 mm thick backing coat in CM 1:4 complete all as specified and directed. |
| 46 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:4 complete. |
| 47 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 15 mm thick screed bed in CM 1:4 complete. |
| 48 | M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:4 complete. |
| 49 | M&L for Parking tile/Out Door coloured ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified |
| 50 | Taking down chowkats or frames with shutters(without taking offshutters from frames) areanot exceeding 1.50 sqm each complete all as specified |
| 51 | Taking down chowkats or frameswith shutters(without taking offshutters from frames) area exceeding 1.50 square metre andnot exceeding 4.0 square metre each complete. |
| 52 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One )vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)(A) Area not exceeding 2.00 sqm each . |
| 53 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor includes cost of glass & wire mesh and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 54 | S&F Aluminium anodized powder coated window & ventilator any type with aluminum anodized outer frame of section 104.0mm x 44.45mm x 1.80mmand inner frame section of 104.0mm x 44.45mm x 1.80mm thick three track aluminium section with rubber gasket andshutter stiles rail of aluminum section of size 25mm x 20mm x 1.5mm thick with suitable locking arrangement fixing glass panes in outer frameshutter covered with fully selected quality tinted glass of 5mm thickness and inner shutter with wire mesh including rubber packing complete, each shutters of window shall be provided with1 Nos 100 mm aluminium handle complete all as specified and as directed. |
| 55 | S&F Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/ 5mm ACP sheet/ 12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty, locking arrangement “GODREJ”, rubber gasket and door stopper complete. |
| 56 | S&F Powder coated aluminium partition with frame of standard powder coated aluminium sections of size 101.60mm x 44.45mm x 2mm in vertical and horizontal members and glazed with 5mm thick tinted glass , 5mm ACP sheet and 12mm thick prelaminated particle board interior grade with laminations on both faces as directed by Engr-in-Charge according to site requirement including jointing cleats, glazing pins, rubber packing and fixing accessories as per site requirement,Inc taking down complete all as specified and as directed. |
| 57 | S&F in repair 1.25 mm lath thicknessSteel rolling shutters, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete with gear box and crank. |
| 58 | Taking down Wall panelling , celing board and similar work complete all as specified and directed by Engr-in-charge |
| 59 | S&F for Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 60 | S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 61 | S&F Suspended Gypsum board ceiling works in decorative steps including vertical/sloping members includes with GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) alongwith perimeter of nailing screw fixed in brick wall/RCCwith the help of nylon seelves and screws at 610mm centre, then suspending GI intermediate channels of size 45mm (0.9mm thick with two flange of 15mm each) from the soffits at 1220mm centre with GI cleat and steel expansion fasteners, ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm centres, 12.5mm tapered edge gypsum board conforing to IS 2095 (1982) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centre,. Screws fixing is done mechanically either with screw driver or drilling machine with suitable attachment finally the board are to be jointed and finishing the tapered and square edges of the boards are to be joints compound, joint fiber tape including dismatling of old false ceiling any description , including two coat of OBD over a coat of chalk whitening putty complete all as specified and directed. Cost of gypsum board is incuded in quoted rate.Note :- Details of fixing & material will be got approved by GE before commencement of work. |
| 62 | M&L of E-board 4mm thick self design type tiles ceiling on GI Powder coated channel/Tee/Grid of make(Armstrong or equivalent) frame work with the following specification including cutting holes to brick wall built in cement mortar & making good in cm1:3 of cement concrete 1:2:4 type BO as required including dismantling of existing ceiling board :-. (a) Plugging to wall around the rooms & supplying & fixing GI Powder coatedangle of size 25x25x1.0 mm (b)S&F of 1.60 mm dia GI wire suspenderswith adjustable clamps including fixing to ceiling dash free fasterers(c) S&F 25 x25 x1.5mm GI Powder coatedtee as in main & cross members at 595mm c/c supported suspenders alongwith adjustable clamp to maintain level . ( d)S&F E-board 4mm thick self design type ceiling tiles of size 595mm x 595mm confirming to relevant IS in squares of GI Powder coatedTee with clips made to shape including taking down. Shadeand pattern of E- oard shall be as approved by GE. |
| 63 | Dismantling of trellis work(jafri) including taking as under of battens in trellis (post and rails measured separately) |
| 64 | M&L for providing precast cement concrete1:2:4 type B-0 using 12.5mm graded aggregate louvres and jallies, 35mm thick (measured solid), including all mouldingsset in CM 1:4 complete all as specified |
| 65 | M&L for Pre-Cast RCC (1:1.1/2:3) (12.5 mm graded crushed stone aggregate) as in pillars of any shape, size & design as approved by Engr-in-Charge and making groves for insert of jafri jallies and fixed with existing jallies/ new jallies as inserting with CM 1:3 completed all as specifed and directed by Engr-in-Charge. |
| 66 | Demolition of reinforced cement concrete of any description and in any position complete all as specified. |
| 67 | M&L for RCC (Nominal mix) type B-1, 1:2:4 (20mm graded aggregate) in bend ,beam , cover slab ,columns, pillars, piers, posts and struts, complete all as specified and as directed by Engr-in-charge |
| 68 | M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, spirally for hopping for columns, hooking ends, and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S or Fe-410-0 complete all as specified & directed |
| 69 | M&L for Rough finished flat surfaces concrete Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels,antilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. all as directed by Engr-in-Charge |
| 70 | S&F of Stainless steel letter,comma,dash ,logo etc of 300mm height and 32mm depth made of 1mm thick stainless sheet with seemless welding rubbed, polished and edges made smooth with necessary fixing devicescomplete all as specified and directed by Engr in charge |
| 71 | S&F, Aluminium composite panel sheet 3mm thick of approved make joint with silicon/adhesive as per manufacturer instrction incl with necessary MS framed workas required shape and sized by welding etc in ceiling/coloumns and in vertical surface complete all as specified and directed. Note : 1. Framed work rates shall be inclusive in ACP Rates .2. Colour and pattern of Sheet will be appoved by GE 3.The rates of necessary scafolding and working platform is included in quoted rate and work isto be carried at approximate 10mtr height. |
| 72 | S&F Precast Prefabricated cement concrete column of requred size and shape suitable with proper size channel for fixing of Pre Fabricated RCC wall pannel of requred size as per site requirent including fixing of cloumns to a required depth as per manufacture\"s instruction incl demolition of existing Rcc column/ copping complete all as specified and directedNote : The excavation of post holes, fixing with PCC Type B1- 1:2:4 and making good surface is included in Quoted rates. |
| 73 | S&F Precast Prefabricated RCC Wall panel of 50 mm to 60 mm thick with suitable size fixed properly in prefaricated columns and sealed properly with filling materials as per manufacture instructions incl demolition of existing Precast Prefabricated RCC Wall panel or RCC jallies ,complete all as specified and directed. |
| 74 | M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface areacomplete all as specified and directed. |
| 75 | M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed. |
| 76 | M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 77 | M&L in repair providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 78 | M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Payment for providing grooves shall be made separately). |
| 79 | M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge |
| 80 | S&F in repair Venition Blinds with Fabirc sides of length and width including Framinghooks and conneting ietms as per specified and directed by Engr in Charge. |
| 81 | S&F 10 mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes including chamfering of edges cutting holes/ slotes for fixing as doors with all tuffen glass door accessories & necessary fixing arrangement ( fittings) like ss handles , heavy duty ss cylinder floor spring ,lock ,top & bottom patch pivot complete all as specified and directed. |
| 82 | S&F factory made WPC jali combining WPC board/Fancy designer type grating and WPC frame 100% solid WPC (wood polymer composite) railing of required length and of 2\" to 2.5\" height , comprising of virgin PVC resin of K value 58-60 (Suspension Grade) , Calcium Carbonate and natural fibres (Wood Powders/rice husk//wheat husk) and non toxic additives, made from single extrusion process, WPC foam board with having minimum density 650kg/cbm and WPC frame having minimum density 780kg/cbm manufactured by an ISO 9001-2015 certified Company, having good screw holding capacity (screw withdrawal strength of 2000N (Face) & 1100N (Edge) , Minimum comprising of 50N/mm2, Modules of elasticity 850N/mm2 and resistance of speed of flame of class A category with property of being termite/Borer free water /Moisture proof and fire resistance. For WPC railing WPC jali to be fixed with WPC frame of size 75x50mm with necessary supporting lengths at vertical as well as horizontal at wall frames to be fixed with 3\"x3\" GI \"L\" or SS cleats to support vertical frame lengths including demolition / dismantling of existing WPC or RCC jallies with frames complete all as specified and as directed.(Note : The said item shall be fixed over boundary walls/roof tops and in any other positions as per requirement at site and cost of frame is included in the quoted rates) |
