|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the All kinds of soil. (DSR 2.2.1) |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (DSR 2.25) |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm (nominal size) (DSR 4.1.10) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) (DSR 4.1.2) |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete (DSR-5.9.1) |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) (DSR-5.2.2) |
| 7 | Brick work with common burnt clay (non modular) bricks of class-150 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR 6.1.2) |
| 8 | Supplying fitting and placing HYSD bar reinforcement in superstructure complete as per drawing and Technical Specifications clauses.5.22.6 |
| 9 | Brick work with common burnt clay (non modular) bricks of class-150 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR 6.4.2) |
| 10 | 12 mm Cement plaster in single coat on rough side of single or half brick wall for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80 mm. in girth and finished even and smooth. (1 Cement :6 coarse sand) (DSR-13.1.2) |
| 11 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (DSR 13.80) |
| 12 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two coats on old work (Royal,Silk) Asian/Berger (DSR 13.41.1) |
| 13 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface (apex Ultima, weather coat All guard) asian , berger (DSR 13.47.1) |
| 14 | Painting or vanishing on iron worksof approved brand nad manufacture of required colour to give an even shade two or more coats on new works over and under coat of suitable shade with ordinary paint of of approved brand and manufacture (DSR 13.62.1) |
| 15 | Providind and fixing angle iron frame for doors,window and ventilator of mild steel angle section of size 35x35x5mm or 35x5 mm flat piece to existing T-iron frame or to the wall with dash fastner including fixing of necessary butt hings and screw and applying a primeing coat of approved steel primer ,all complete as per the direction by Engineer-in-charge dsr 10.31 |
| 16 | Supply and fixing ISI marked 30 mm thick flush door shutter commercial quality conforming to IS : 2202 (Part I) including fixing of wooden cleat of stoppers and including fixing and adjustment of hinges, bolts, locks, handles complete work. (Fitting with necessary screws to be paid seperatly). (DSR 9.21.2) |
| 17 | Providing and laying Vitrified floor tiles in different sizes (Thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 coarse sand), Jointing wtih grey cemnet slurry @ 3.3 kg/sqm including grouting the joints with white cemtn and matching pigments etc. complete.tiles must be cut with zero chipping diamond cutter only . Laying of tiles wil be done with be notch trowel,piller wedge,clips of required thickness ,levelling system and rubber mallet for placing the tiles gently an deasily.SIZE 600X600 11.41A.1 Doublr charged vritified tiles polished finished of size. |
| 18 | Providing and fixing float glass panes 4 mm thick glass pane (seight not less than 10kg/sqm) (DSR No.9.7.7.1) All Item Rate are Excluding GST Please Enable Macros to View BoQ information |
