|
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. |
| 2 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 3 | Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with:(A) Querry,Cement mortar 1:6 (1 Cement : 6 coarse sand) |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level,1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 6 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts andstruts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.,1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing inposition and binding all complete above plinth level Mild steel and medium tensile steel bars. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns etc. for mass concrete. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for:Columns, pillars, piers, abutments, posts and struts |
| 10 | Constructing vertical bunds with sloping faces, by boulder filling (dry,hand packed tightly); including cost of stones but excluding cost of wirecrates |
| 11 | Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete. |
| 12 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand), Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 13 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement :4 coarse sand),Extra for half Brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. |
| 14 | CEMENT PLASTER (IN FINE SAND)12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 15 | CEMENT PLASTER (IN FINE SAND) 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 16 | Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. |
| 17 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc.complete:50 mm thick with 20mm nominal size stone aggregate. |
| 18 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm |
| 19 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area of 3 sqm. and below |
| 20 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead : Of area of 3 sqm. and below |
| 21 | Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet |
| 22 | Providing and laying Vitrified tiles in floor with different sizes(thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of tile 600x600 mm |
| 23 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 24 | Applying priming coat: With ready mixed aluminum primer of approved brand and manufacture on resinous wood and ply wood |
| 25 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. |
| 27 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade on old work (one ormore coats) |
| 28 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class kail wood |
| 29 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 30 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.1 mm thick |
| 31 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/liter |
| 32 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 33 | Renewing glass panes, with wooden fillets wherever necessary :Float glass panes of thickness 4.0 mm (weight not less than 10.0 kg/sqm) |
| 34 | Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete,With Galvanized M.S. Wire gauge with wire of dia 0.63 mm :With 2nd class teak wood beading 62x19 mm |
| 35 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class Kail wood.: 30 mm |
| 36 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 30 mm Second class kail wood |
| 37 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately)..35mm thkSecond Class kail wood |
| 38 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Second Class kail wood |
| 39 | Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) : |
| 40 | Structural steelwork in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.Welded |
| 41 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 42 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.0.80 mm thick with zinc coating not less than 275 gram/m2 |
| 43 | Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections 0.80 mm thick with zinc coating not less than 275 gram/m2 |
| 44 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion(i) Single socketed pipes 110 mm diametre |
| 45 | Providing and fixing plain, square edged wooden beading 65x12 mm section with screws of approved quality for ceiling 12.48.1 2nd class teak wood. 12.48.2 1st class deodar wood. 1st class kail wood. |
| 46 | Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS: 14842-2000, including top cover of 6mm coir veneer board, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100mm x 40mmx40 mm on both inner side of pelmet and rawl plugs 75mm long etc. all complete. |
| 47 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 meter openable length ( total length 90m), having 50 nos rounds per 6 meter length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape (R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ meter (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 48 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.-2mm thick |
| 49 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour or shade (Area of slab over 0.5 sqm) , 18mm. |
| 50 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 250x10 mm |
| 51 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 100x10 mm |
| 52 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete :250x16 mm |
| 53 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges (heavy weight) with Stainless Steel screws etc. complete. 125x64x2.50 mm |
| 54 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing,panelling and dash fasteners to be paid for separately.)For fixed portion, Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) |
| 55 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin- charge. (Cost of aluminum snap beading shall be paid in basic item.)With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm) |
| 56 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 57 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.-100 MM |
| 58 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.-75 MM |
| 59 | Providing and fixing bright finished brass hard drawn hooks and eyes :200 mm |
| 60 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm |
| 61 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :150x10 MM |
| 62 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :100x10 MM |
| 63 | Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :Twin Rubber stopper |
| 64 | Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gram/m2 |
| 65 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 66 | Providing and fixing 600x120x5mm glass shelf with edges round offsupported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc.complete |
| 67 | Providing and fixing PTMT towel railcomplete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms. |
| 68 | Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms |
| 69 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.:Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall:15 mm dia. nominal bore |
| 70 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc.:Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall:20 mm dia. nominal bore |
| 71 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 72 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour20 mm nominal bore, weighing not less than 40gms |
| 73 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete. 25 to 40 mm nominal bore |
| 74 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 |
| 75 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 76 | Providing and fixing PTMT grating of approved quality and colour.Circular type,100 mm nominal dia. |
| 77 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board610x510mm bowl depth 200mm |
| 78 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. |
| 79 | Providing and fixing uplasticized PVC connection pipe with brass unions,45 cm , 15 mm nominal bore |
| 80 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge |
| 81 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: 18.3.1 W.C. pan with ISI marked white solid plastic seat and lid. |
| 82 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 83 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete Flexible pipe40 mm dia |
| 84 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single tee with door 110x110x110 mm |
| 85 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:door-Bend 87.5° : 110 mm bend |
| 86 | Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable, in surface or recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box, and earthing of the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable, complete as required. Group -A |
| 87 | Wiring for circuit / submain wiring along with earth wire, with the following sizes of FRLS/HFFR PVC insulated copper conductor single core cable, in surface or recessed medium class PVC conduit, complete as required.- (a)2 x 2.5 sq mm + 1 x 2.5mm2 earth wire |
| 88 | (b) 2 x 4 sq mm + 1 x 4mm2 earth wire |
| 89 | Supplying and fixing suitable size GI box with modular plate and cover in front, on surface or in recess, including providing and fixing 6-pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, with connections, complete as required. |
| 90 | Supplying and fixing the following modular switch/socket on the existing modular plate and switch box, including connections but excluding modular plate, etc., as required.-(a)5/6 A switch |
| 91 | (b)3 pin 5/6 A socket outlet |
| 92 | Supplying and fixing two-module stepped type electronic fan regulator on the existing modular plate and switch box, including connections but excluding modular plate, etc., as required. |
| 93 | Supplying and fixing the following size/modules GI box along with modular base and cover plate for modular switches in recess, complete as required. -(a)4 Module (125mmX75mm) |
| 94 | (b)6 Module (200mmX75mm) |
| 95 | Supplying and fixing the following way, horizontal type, three pole and neutral, sheet steel MCB distribution board, 415 V, on surface or in recess, complete with tinned copper bus bar, neutral bus bar, earth bar, DIN bar, interconnections, powder-coated painting, including earthing, etc. as required (but without MCB/RCCB/Isolator).4 way (4+12), Double Door |
| 96 | Supplying and fixing Cable End Box (Loose Wire Box) suitable for the following triple pole and neutral, sheet steel MCB distribution board, 415 V, on surface or in recess, complete with testing and commissioning, etc. as required. - For 4 way, Double door TPN MCBDB |
| 97 | Supplying & fixing 5 A to 32 A rating, 240 V, 10kA, \"C\" curve,, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required- Single pole |
| 98 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.- 100 A, 16 KA, TPMCCB |
| 99 | Supplying and fixing following rating, four pole, (three phase andneutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. - 25A |
| 100 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, refilling the trench etc as required. protective covering and refilling the trench etc as required. - Upto 35 sq. mm |
| 101 | Laying and fixing of one number PVC insulated and PVC sheathed /XLPE power cable of 1.1 KV grade of following size on wall surface as required. - Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 102 | Earthing with copper earth plate 600mm x 600mm x 3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/coke and salt as required |
| 103 | Installation of exhaust fan existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing & commissioning as required.- Up to 450 mm sweep |
| 104 | Supply, Installation, Testing and Commissioning of ceiling fan with Brushless Direct Current (BLDC) motor, insulation class B, 3 Nos. metallic (Aluminium alloy) blades, 30 cm long down rod, 2 Nos. canopies, shackle kit, safety rope, copper winding, steel/Aluminium body, power factor not less than 0.9, service value ≥ 6.0 (CM/M/W), speed 350 RPM (tolerance as per IS: 374-2019), Total Harmonic Distortion (THD) less than 10%, suitable for operation with regulator for speed control, complete with all accessories including safety pin, nut bolts, washers; maximum temperature rise 75°C, insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single-phase AC supply. Ceiling fan shall be compliant with IS: 374-2019, including external connections with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single-core cable and earthing, complete as required. 1200 mm sweep |
| 105 | \"Supplying, Installation, Testing & Commissioning of LED surface-mounted batten light of body material and construction as per IS: 10322, with replaceable driver, driver efficiency >85%, operating voltage AC 140–270 V, frequency 50/60 Hz, operating temperature range –5 °C to 40 °C, internal surge protection of 2.5 kV with short & open circuit protection, THD <10%, power factor ≥0.95, IP20, CRI >80, flicker-free (flicker <5%), minimum lifetime of 50,000 burning hours with 70% lumen maintenance, CCT options 3000 K / 4000 K / 5700 K / 6500 K (ANSI Bin), SDCM <3, maximum power consumption not exceeding specified rating, and luminaire fixture compliant with relevant BIS standards. The fixture shall have manufacturer’s word mark/name engraved/embossed/screen printed on housing. External connections with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single-core cable and earthing, complete as required. The luminaire shall be powder-coated die-cast/extruded aluminium body (thickness >1.20 mm) with thermal management to ensure LED junction temperature <90 °C, minimum system lumen efficacy ≥105 <120 lm/W, with LM79 & LM80 test reports and all BIS-required testing. Minimum 5 years OEM warranty shall be provided. Wattage: 18–22 W\" |
| 106 | Installation, testing & commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection |
| 107 | mirror light |
| 108 | LED Street Light Fixture, powder-coated pressure die-cast aluminum body, system lumen efficacy >135 lm/W, of the following wattages, complete with driver and all accessories as required, suitable for outdoor use. Wattage: 72 W |
| 109 | Geyser 50 Ltr. 5 Star rating |
| 110 | Exhaust Fan 200 mm |
| 111 | 35 SQMM4 core Aluminum Armored cable |
| 112 | 4 SQMM3 Coppercable |
| 113 | GST@18% |
