|
| 1 | Taking down mild steel gate of hanger exceeding 10 Sqm but not exceeding 15 Sqm including refixing in same opening after repair with crane complete all as directed. |
| 2 | Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as directed. |
| 3 | Material and labour for PCC 1:2:4 type B2 using 40 mm graded crushed stone aggregates as in Foundation, filling and mass concrete complete all as specified. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed by Engineer-In-Charge. |
| 5 | Supply and fix rolled sections as in post main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410 -W (Gde-E- 250) quality-A complete all as directed. |
| 6 | Supply and fix roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410 -W (Gde-E- 250) quality-A complete all as specified. |
| 7 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 8 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 9 | Material and labour for preparation of new and previously untreated steel or ironsurfaces of any description, not otherwise described exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat ofred oxideprimer all as specified. |
| 10 | Material and labour for polyurethyne paint over hanger flooring, 3mm EPU system (100 micron primer), 2 mm epoxy screed, 1 mm self levelling EPU top coat including cleaning the existing surfaces, all as manufacturer instruction. |
| 11 | Demolition of Brickwork or stone/ boulder masonry,including allquoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar complete all as directed by Engineer-in-Charge. |
| 12 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed by Engr- In- Charge. |
| 13 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as directed. |
| 14 | Dismantling timber scantlings 40 sqcm and over in section for unframed work, in any position all as directed. |
| 15 | Material and labour for clean sawn second class hardwood in scantlings timber framed and fixed complete all as specified. |
| 16 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified. |
| 17 | Excavation in trenches not exc. 1.5 m wide not exc. 1.5 m in depth; for laying of cables not exc. 10 Sqm on plan and getting out , trimming sides, forming bottom surface to required level complete in soft/ loose soil all as specified and as directed. |
| 18 | Excavation in trenches not exc. 1.5 m wide exc. 1.5 m but not exc. 3.0 m in depth; for laying of cables not exc. 10 Sqm on plan and getting out , trimming sides, forming bottom surface to required level complete in soft/ loose soil all as specified and as directed. |
| 19 | Removing excavated materials (soils) not exc 50.00mtr and depositing where directed at a level not exc 1.50 mtr above the starting point in soil, complete all as specified and as directed. |
| 20 | Returning filling in soft/loose soil, including, spreading, levelling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed. |
| 21 | Material and labour for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregates as in Foundation, filling and mass concrete complete all as specified. |
| 22 | Material and labour Reinforced cement concrete M-25 (design mix) using graded stone aggregate as in foundation including rafters footings foundation beam plinth beam bases for column etc basement slab under reamed piles and mass concrete complete all as specified and directed. |
| 23 | Material and labour for Reinforced cement concrete M-25 (design mix) using graded stone aggregate as in columns, pillars, posts and struts etc complete all as specified and directed. |
| 24 | Material and labour Reinforced cement concreteM-25 grade with graded aggregatebeams, cantilever, bressummers, lintels over 1.5 m span complete all as specified and directed . |
| 25 | Material and labour Reinforced cement concreteM-25 grade with graded aggregate as in chajjas complete all as specified. |
| 26 | Material and labour for Use and waste of flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete complete all as specified and directed. |
| 27 | Material and labour for use & waste ofForm work to sides of square, rectangular or polygonal pillars, posts, columns etc for flat rough finished surfaces complete all as specified and directed. |
| 28 | Material and labour for Use and waste of flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed. |
| 29 | Material and labour for use and waste for formwork to chullah hoods, chajjas, troughs and similar items in cluding edges for rough finished flat surfaces of concrete complete all as specified. |
| 30 | Material and labour for TMT bars 8-10 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips,complete all as specified and directed. |
| 31 | Material and labour for TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers & binders,cut to length, bent to shapes required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 32 | Material and labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified. |
| 33 | Material and labour for treating the bottom, sides of excavation andsoil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified. |
| 34 | Material and labour for precast cement concrete block 1:3:6 type C1 using 20 mm graded crushed stone aggregates masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6, complete all as specified. |
| 35 | Material and labour for machine cut kota stone slab flooring 20-25mm thick over cement screed baselaid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 36 | Material and labour for machine cut kota stone slab as in skirting 20-25 mm thick over cement mortar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 37 | Material and labour for 7 to 8 mm thick joint free premium quality anti skid colourceramic tiles size of each tiles should be 400 mm x 400 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces including 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 38 | Material and labour for 7 mm thickjoint free premium quality glazed ceramic colourtiles of size 450 mm x 350 mm/ 600 mm x 300 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 39 | Material and labour for 40 mm PCC type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in flooring finished the surface evan and smooth without using extra cement, completed all as specified. |
| 40 | Material and labour for 25 mm PCC type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in sub-base finished the surface evan and fair, completed all as specified. |
| 41 | Material and labour for 75 mm PCC type C2, 1:3:6 using 40 mm graded crushed stone aggregates as in sub-base finished the surface evan and fair, completed all as specified. |
| 42 | Material and labour for 50 mm PCC type C2, 1:3:6 using 40 mm graded crushed stone aggregates as in plinth protection finished the surface evan and smooth without using extra cement, completed all as specified. |
| 43 | Material and labour for Hardcore of broken stone or boulder gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified. |
| 44 | Material and labour for moorum/ red bajri filling in floors or pavings, laid in layers n exc.15 cm thick, spread, levelled and rammed including watering complete all as specified. |
| 45 | Material and labour for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finshed even and smooth without using extra cement complete all as specified. |
| 46 | Material and labour for 20 mm thick renderingin cement mortar 1:4 in two layers (12 mm +8 mm) on external faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement with using approved Liquid Water Proofing Compound on second layer (8 mm) as per manufacturer instruction complete all as specified and as directed by Engineer-In-Charge. Note: Liquid Water Proofing Compound shall be measured and paid including this item |
| 47 | Material and labour for 5 mm thick renderingin cement mortar 1:3 on fair faces of ceiling surfaces, finished the surfaces even and smooth complete all as specified. |
| 48 | Supply and fix Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-410W Grade E-250 (quality A) complete all as specified. |
| 49 | Supply and fix Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified. |
| 50 | Supply and fix 1 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required all as specified. |
| 51 | Supply and fix 1 mm thick steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type including safety lever locks mild steel with 4 levers for rolling shutters complete all as specified. |
| 52 | Supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 53 | Supply and fix powder coated aluminium window and ventilator shutters powder coating of any colour (Thickness or powder coating not less than 50 micron), side hung/ sliding type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 54 | Supply and fix PVC door frame of size 50 mm X 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified. |
| 55 | Supply and fix30 mm thick factroy made solid panel PVC door shutter(style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuct inside the solvent cement forstyle and single side pre laminatedPVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top railsand bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification . |
| 56 | Supply and fix 4.80 mm thick sheet glass, ordinary quality and glazingin square exceeding 0.50 sqm in each panein aluminium joineryin each pane complete all as specified. |
| 57 | Supply and fix 100 mm long medium weight, cold rolled mild steel, Butt hinges,complete all as specified. |
| 58 | Supply and fix 200 mm long aluminium anodised barrel tower bolts of extruded section all as specified. |
| 59 | Supply and fix 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 60 | Supply and fix 150 mm long aluminium alloy handles, fabricated type, anodized all as specified. |
| 61 | Supply and fix small fittings for 1st class hardwood such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cucm each complete all as directed. |
| 62 | Material and labour for applying two or more coatsof 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces. |
| 63 | Material and labour for preparation of newly plastered surfaces of wall and applying distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour complete, as per manufacturer\"s specification. Two or more coats over a coat of wall care putty complete all as directed. |
| 64 | Material and labour for preparation of newly plastered surfaces of ceiling and applying distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour complete, as per manufacturer\"s specification. Two or more coats over a coat of putty complete all as directed. |
| 65 | Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified. |
| 66 | Supply and fix Fe-410-W(GdeE-250) qualityA Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified. |
| 67 | Supply and fix mild steel screw bolts (machine made) of dia 20 mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5 cm but not exc 30 cm long complete all as specified and directed. |
| 68 | Material and labour for for suspended false ceiling using grid 180 GSM (exposed ceiling suspension system ) of grid size 605 mm x 605 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 12 mm thick fibre insulation boards ordinary type, flame retardant type, treated on one face only in a grid of powder coated GI system duly suspended with 16 mmdia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1210 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1210 mm cross tee to be interlocked between main runners @ 605 mm c/c,so as to form 600 mm x 600 mm grid complete all as specified . |
| 69 | Material and labour for for suspended false ceiling using grid 180 GSM (exposed ceiling suspension system ) of grid size 605 mm x 605 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 6 mm thick High Pressure steel Non Asbestos Fibre Cement decorative Board in a grid of powder coated GI system duly suspended with 4 mmdia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1210 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1210 mm cross tee to be interlocked between main runners @ 605 mm c/c,so as to form 600 mm x 600 mm grid complete all as specified . |
| 70 | Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as specified. |
| 71 | Material and labour for plain cement concrete 1:3:6 type C2 using 40 mm graded aggregate as in surface channel complete all as specified. |
| 72 | Material and labour for cement concrete type B0, 1:2:4 (12.50mm graded aggregate), rounded or chamfered on edges in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping kneelers, apex stones, bed plates, kerbs not provided for roof kerbs or mud stops, rounded or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including water proofing compound complete all as specified |
| 73 | Supply and fix 1 mm thick 150 mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges complete all as specified. |
| 74 | Material and labour for second class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified. |
| 75 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15 mm dia |
| 76 | Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but not exceeding 20 cm girth complete all as specified. |
| 77 | Supply, lay and fix 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 78 | Supply and fix as in repair 15 mm bore quarter turn Bib taps, chromium plated, cast copper alloy, with wall flange concealed type screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. |
| 79 | Supply and fix as in repairs 15 mm bore single lever wash hand basinmixture complete as per manufacturer instruction. |
| 80 | Supply and fix as in repairs15 mm dia cast copper alloy chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe of for unions complete all as specified and directed. |
| 81 | Supply and fix as in repairs vitreous china wash down water closet pan (pedestal pattern) with seat and cover closed pattern flat bottom, and mild steel chromium plated or aluminised hinging devicewhite colour with \"P\" or \"S\" trap including connection to drains (or outgoing pipes) and to the flushing pipes, complete all as per manufacturer instruction |
| 82 | Supply and fix as in repairs 10 ltrs capacity PVC valveless syphonic action type, low level flushing cistern, white with inlet, ball valve float and handle including brackets and 32 mm dia PVC low or high density flush pipe complete all as per manufacturer instruction |
| 83 | Supply and fix as in repairs CP health faucet with tube and wall hook including all fittings as per manufacturer instruction. |
| 84 | Supply and fix as in repairs 20 mm dia chromium plated tubular towel rail and 600 mm long with brackets, complete all as specified. |
| 85 | Supply and fix as in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified. |
| 86 | Supply and fix as in repairs Vitreous China wash basin, white, flat back, size 550 mm x 400 mm including 32 mm dia waste fittings and waste pipe including brackets complete all as specified. |
| 87 | Supply and fix as in repairs 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. |
| 88 | Supply and fix as in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified. |
| 89 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as directed. |
| 90 | Supply and fix Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming toFe 410-W (Gde E- 250) quality-A complete all as specified. |
| 91 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified. |
| 92 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified |
| 93 | Material and labour for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregates as in Foundation, filling and mass concrete complete all as specified. |
| 94 | Material and labour for preparation of new and previously untreated steel or ironsurfaces of any description, not otherwise described not exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat ofred oxideprimer all as specified. |
| 95 | Supply and fix as in repairs 2 mm thick polycarbonate solid embossed sheet fixing with self tapping screws complete all as per manufacturer instruction. |
| 96 | Material and labour for point wiring with 1.50 Sqmm PVC insulatedun sheatned multi stranded copper conductor cable (FRLSH) 1100 volts grade two single core conforming to IS-694-1990 and one run of continious earth wire with 1.50 Sqmm PVC insulated unsheatned stranded copper conductor cable (FRLSH) draw in and including heavy duty 20 mm dia steel conduit(ISI marked) in concealed with all necessaryfittings and fixures and switch, socket, regulator, fan point, exhaust fan point etc. including making good disturbed surface with CM (1:4) to match with the existing surface complete all as specified for the following :- Note:-(a) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing.Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.(b) Quoted rates shall be deemed for conduit,cutting chases of wall, making good disturbed wall.(c) The metal flush box with modular cover plates with frame measured and paid separately. |
| 97 | One light/ fan/ exhaust fan/ bell point controlled by one nos, one way switch (for flame proof) |
| 98 | One light/ fan/ exhaust fan/ bell point controlled by two nos, two way switch (for flame proof) |
| 99 | All as per Item No 96.00 but One 3 pin socket outlet. 15 amps, independent, with cables 4.00 sq. mm size complete all as specified. |
| 100 | Material and labour for point wiring with 1.50 Sqmm PVC insulatedun sheatned multi stranded copper conductor cable (FRLSH) 1100 volts grade two single core conforming to IS-694-1990 and one run of continious earth wire with 1.50 Sqmm PVC insulated unsheatned stranded copper conductor cable (FRLSH) draw in and including heavy duty 20 mm dia PVCconduit(ISI marked) in concealed with all necessaryfittings and fixures and switch, socket, regulator, fan point, exhaust fan point etc. including making good disturbed surface with CM (1:4) to match with the existing surface complete all as specified for the following :- Note:-(a) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing.Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.(b) Quoted rates shall be deemed for conduit,cutting chases of wall, making good disturbed wall.(c) The metal flush box with modular cover plates with frame measured and paid separately. |
| 101 | One light/ fan/ exhaust fan/ bell point controlled by one nos, one way switch |
| 102 | One 5 pin 6 Amps switch socket outlet point controlled by one switch on same board with other switches |
| 103 | One 5 pin 6 Amps switch socket outlet point controlled by one switch on independent board. |
| 104 | All as per Item No 98.00 but One 3 pin socket outlet. 15 amps, independent, with cables 4.00 sq. mm size complete all as specified. |
| 105 | Supply and fix Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V all as specified. |
| 106 | Supply and fix Switch flame proof rotary type with termination box in LM6, 16A, two pole 250V all as specified. |
| 107 | Supply and fix Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P + earth complete all as specified. |
| 108 | Supply and fix Modular type Switch , flush type single pole one way 10 Amps 240V. |
| 109 | Supply and fix Modular type Switch , flush type single pole one way 20 Amps 240V. |
| 110 | Supply and fix modular socket outlet , 2 module, 3 pin 6 Amps 240 V flush type . |
| 111 | Supply and fix Modular socket outlet 2 module , 3 pin 6 to 16 Amps 240 V flush type . |
| 112 | Supply and fix modular metal flush box with modular white cover plate with frame , 3 module complete all as specified. |
| 113 | Supply and fix modular metal flush box with modular white cover plate with frame , 6 module complete all as specified. |
| 114 | Supply and fix modular metal flush box with modular white cover plate with frame , 8 module complete all as specified. |
| 115 | Supply and fix ceiling rose surface baklite with three terminals 240 V. |
| 116 | Supply and fix sheet metal enclosure MCB DB TPN with din rail 06 way 415 V (double door type) with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc. and making good of disturbed surface to match with existing colour of wall complete all as specified.Note: (a) Quoted rates shall be deemed for brick wall / concrete wall cutting and making good as per existing surfaces. |
| 117 | Supply and fix MCB SP 240 volts, 50 Hz capacity 40 Amps \"C\" curve all as specified. |
| 118 | Supply and fix MCB TPN 240 volts, 50 Hz capacity 6-32 Amps \"C\" curve all as specified. |
| 119 | Supply and fix LED lights fitting 1x 20W, 220V, warm white/ pure white AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specifed and directed.Note:- (a) LM-80 certificate from NABL accredited Lab shall be submitted for LED light fittings.(b) Warranty certificate shall be submitted for LED light fitting as per standered format for minium 50000 Hrs.(c) LED light fitting and drivers shall be of same make. |
| 120 | Supply and fixLED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC warm white/ pure white decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specifed and directed.Note:- (a) LM-80 certificate from NABL accredited Lab shall be submitted for LED light fittings.(b) Warranty certificate shall be submitted for LED light fitting as per standered format for minium 50000 Hrs.(c) LED light fitting and drivers shall be of same make. |
| 121 | Supply and fix FlameproofLight 40W Batten ensures safe operation in industries like Automotive, petrochemical, and manufacturing. The batten provides efficient and uniform lighting while preventing ignition risks. It is ideal fortallation in areas with low to medium ceilings or narrow spaces. Batten supports single and twin T8 tubes (20W/40W) Certifed by CIMFR, BIS and PESO Gas Group IIA IIB Zone Classification Zone 1 Zone 2 Templassification - T6 complete as directed . |
| 122 | Material and labour for earthing complete with galvanised earth plate 60 cm X 60 cm X 6.00 mm thick buried vertically in ground to depth not less than 2.25 metres deep below ground level, with top edge of earth plate not less than 1.5 m below ground level, connected to connected to galvanised earth lead wire 4.0mm dia by means by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, GI pipe light grade 40mm bore for protection of earth wire and connected to continous earth lead on pole/test point, supplying and laying charcoal dust common salt PCC 1:2:4 type B1, chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm C/C both ways with MS handle 12mm dia, PGI/CI funnel and wire mesh, 20mm dia GI pipe medium grade for watering all as shown in electrical plate No 5 on srl page No 497 of SSR Part I (2009)drawing and connection to earth test point including testing and including dismantling and taking out old earthing complete all as specified and directed.Note : (i) The cost of earth lead /strip and GI pipe for protection of earth lead/strip upto 7.5m is included in the quoted rate.(ii)The cost of excavation, earth work is included in the quoted rate. |
| 123 | Material and labour for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire complete all as specified and directed. |
| 124 | Supply and fix flame proof exhaust fan with louvermetal body,heavy duty, double ball bearing, 1400 RPM,70 watt, 4 blades, air delivery 1770 m3 /h, suitable for SP 230/250 Volts, 50 Hz AC supply complete with louver shutter including fixing/ grouting of frame & louvers in wall & connecting with and including 3 Nos 1.5 Sqmm single core, PVC insulated but unsheathed FRLS 1100 Volts grade cable with multistranded copper conductor from ceiling rose to fan complete all as directed. |
| 125 | S & F exhaust fan of 300 mm sweep,metal body,heavy duty, double ball bearing, 1400 RPM,70 watt, 4 blades, air delivery 1770 m3 /h, suitable for SP 230/250 Volts, 50 Hz AC supply complete with louver shutter including fixing/ grouting of frame & louvers in wall & connecting with and including 3 Nos 1.5 Sqmm single core, PVC insulated but unsheathed FRLS 1100 Volts grade cable with multistranded copper conductor from ceiling rose to fan complete all as directed. |
| 126 | Supply and laying, connecting, testing, commissioning LT UG cable XLPE Insulated,armoured,electric powercables (heavy duty) 1100 Volts grade conforming to IS 7098 withaluminium conductor multi-strand of cross-sectional area 16 Sqmm 4.00 Core laid in trenches / ducts/ inside protection pipe including cable glands, lugs and suitable size of MS saddle clips etc. alsoall as directed by Engr-In-Charge.Note:-(a) Excavation, sand cushioning, bricks shall be measured and paid separately |
| 127 | Supply and filling for dry sand in cable protection trenches before and after the cables are laid, for sand cushioning to cables complete all as specified and directed. NOTE : thickness after punning of sand shall be (minimum as specified in SSR) measured and paid in this item. |
| 128 | Material and labour for brick protection for UG XLPE cable with burnt clay old size sub class \"B\" bricks laid dry and flat abutting each other with gaps between adjacent brick not more than 10mm and width equal to length of brick in trenches across the cable complete all as directed by Engineer-In-Charge.Make: Best quality locally available which is duly approved by GE. |
| 129 | Material and labour for tubes \"light grade\" galvanised with all fittings laid in trenches of 40 mm bore dia. |
| 130 | Supply and fixing three phase motot for Industrial Heavy door opening and closing process of capacity 2 HP motor, 415 volt, 50HZ IP 55, RPM 1415 to 1500 including switch gear starter controll panel with proper relay system including electrical connection between motro stater copper cable . Motor testing and commissioning of complete motor and starter using for steeel metal door all as specified and directed. |
