|
| 1 | PART-I : Service |
| 2 | Excavation of earth in all kinds of soil by Hydraulic excavator / manual means for trenches, footing, drains, steps etc. in soft soil up to a depth not exceeding 1.5 m, filling around foundation and in plinth with selected excavated soil in layers not exceeding 150 mm in thickness watering and consolidating etc. disposing surplus earth upto a lead of 10 Km all as per specification complete as per directions of Engineer-in-charge. |
| 3 | Supplying and laying cement concrete 1:3:6 (1 Cement : 3 coarse sand: 6 graded stone aggregate) for using graded stone aggregate 20mm maximum size including, formwork, consolidation, finishing and curing as per specification and drawing. (Cement content. 220 Kg./ M3) |
| 4 | Supplying and laying bricks masonry usingbricks having minimum compressive strength 70 Kg./sq.cm. and water absorption shall not exceed 20% by weight withcement mortar 1:6 (1 cement : 6 coarse sand) at all elevation including, simultaneous pointing below plinth level and racking out joints above ground level, curing,scafolding etc. complete |
| 5 | Laying of bricks masonry using old available brick with Cement mortar 1:6 (1 cement : 6 coarse sand) including removing, cleaning, stacking, simultaneous pointing, racking out of joints, curing etc. complete for at all levels as per specification including Scafolding complete. |
| 6 | Providing pointing on brick masonry wall with cement mortar 1:3 (1 cement : 3 coarse sand) including racking out joints, cleaning brick work, scaffolding and curing etc. complete as per direction of Engineer-in-charge. |
| 7 | Providing 15 mm thick cement plaster with cement mortar 1:4 (1 cement : 4 coarse sand) on brick or concrete surface etc. including preparation of surface, hacking, removing of loose materials cleaning of joints, finishing, curing, scaffolding complete all as per direction of Engineer-in-charge. including disposal of rubbish upto a lead of 10 Km all as per specification.. |
| 8 | Providing and laying cement concrete 1:2:4 (1 Cement : 2 Coarse sand : 4 graded stone aggregate (Minimum Compressive Strength 150 Kg. / cm2 ) using graded stone aggregate 20mm maximum size for R.C.C., P.C.C., precast work as per site requirement including mixing with mechanical mixer, form-work, consolidation, finishing, and curing complete for all works(Cement content 320 Kg/Cum ) including repair works and as per specification and direction of Engineer-in-charge. |
| 9 | Providing and laying 1:1.5:3(1 Cement : 1.5 Coarse sand : 3 graded stone aggregate) (Minimum Compressive Strength 200 Kg. / cm2 ) for boundary wall coping, footpaths ,R.C.C., P.C.C., precast work & others floors etc. as per site requirementusing graded stone aggregate 20 mm maximum size and down graded including scaffolding, formwork, mixing by mechanical mixer, pouring, mechanical vibrating, consolidation, finishing, curing by hessian and making removable cement bunds where ever applicable etc. completeall as per specification and directed by EIC. (Using minimum Cement Content 350 Kg./M3).Note: Reinforcemnt will be paid in separate item. |
| 10 | Providing & placing in position Reinforcementbars (TMT) conforming to IS-1786, for reinforced cement concrete at all levels including supplying, cutting, bending, fixing, tying in position with 1.6 mm dia. soft drawn annealed binding wire with chair supports, spacer bars etc. complete including cost of transporting, decoiling, straightening and binding wire. |
| 11 | Dismantling/breaking of existing concrete/RCC and brick work, cleaning of bricks, stacking serviceable material and disposal of rubbish by Tractor/buggiupto a lead of 10 Km as directed by Engineer-in-charge. |
| 12 | Providing and laying cement concrete flooring 1:2:4 (1 Cement : 2 Coarse sand : 4 graded stone aggregate) (IPS) finished with a floating coat of neat cement, including cement slurry, 40 mm thick using graded stone aggregate up to 20 mm max size laid to level, slope, in alternate days finished smooth including providing and fixing 40 mm wide and 4 mm thick glass dividing strip, rammingcuring etc. complete. |
| 13 | Providing and laying 40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 28 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) and top layer 12 mm thick with white, black, chocolate, grey yellow, green etc. marble chips of sizes from 7 mm to 10 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 2:3 (2 cement marble powder mix : 3 marble chips) by volume, including cement slurry etc. complete. |
| 14 | Providing and laying 115mm thick soling with brick of uniform shape usingbricks having minimum compressive strength 70 Kg./sq.cm2including leveling, compaction and dressing the surface by cutting, transporting and filling the earth, complete to the required level and shape laying bricks with joints staggered and filling with earth and disposal of surplus earth upto a lead of 2Km all as per specification. |
| 15 | Supply and fixing of Stainless Steel wire mesh mosquito proof jali 12 mesh per inch, having wire of approx. minimum 0.28mm dia as per requirement at site etc. complete on door/window shutters including, removing of old net fixed to MS/Wooden Door/Window shutters with supply and replacing of wooden/steel beading, screws etc.complete all as per direction of Engineer-in-charge. |
| 16 | Supplying and fixing of window glass panes of make Saint gobain or Modi guard, 4mm thick with wooden/M.S beading including removal of broken fittings, if needed for window shutters all sizes and at all height complete all as per direction of Engineer-in-charge. |
| 17 | Supplying and Fixing 5mm thick frosted glass of make Saint gobain or Modi guard in window after removing the damaged glass pieces, beading including removal of broken fittings, if needed for window shutters all sizes and at all height complete all as per direction of Engineer-in-charge. |
| 18 | Providing and laying Vitrified tiles (Double charge) of minimum size 600X600mm (thickness not less than 8 mm)ofmake H&R JOHNSON or KAJARIA or NITCO or Orient Bell, conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Note- In order to maintain the slope of the flooring of the room, the extra mortar at the high and of the rooms will have to be provided by the Contractor at his own cost.No extra paymet will be made for the extra thickness of mortar provided by the contractor to maintain the minimum slope of the granite flooring. |
| 19 | Providing and fixing Ist quality ceramic glazed wall / floor tilesmake conforming to IS: 15622 (thickness not less than 8 mm), ofmake H&R JOHNSON or KAJARIA or NITCO or Orient Bell, in all colours, shades as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Note- In order to maintain the slope of the flooring of the room, the extra mortar at the high and of the rooms will have to be provided by the contractor at his own cost.No extra paymet will be made for the extra thickness of mortar provided by the contractor to maintain the minimum slope of the granite flooring. |
| 20 | Providing and fixing premium quality mat finished Anti skid ceramic floor tiles of required size (thickness not less than 8 mm) ofH&R JOHNSON or KAJARIA or NITCO or Orient Bell make, in all colours, shades as approved by Engineer-in- Charge, in bathroom, skirting, risers of steps, flooring, outdoor, indoor etc. over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Note- In order to maintain the slope of the flooring of the room, the extra mortar at the high and of the rooms will have to be provided by the contractor at his own cost.No extra paymet will be made for the extra thickness of mortar provided by the contractor to maintain the minimum slope of the granite flooring. |
| 21 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete with minimum 15 mm thick stone slab over 12 mm (average) thick base of cement mortar 1:3 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Note- In order to maintain the slope of the flooring of the room, the extra mortar at the high and of the rooms will have to be provided by the contractor at his own cost.No extra paymet will be made for the extra thickness of mortar provided by the contractor to maintain the minimum slope of the granite flooring. |
| 22 | Providing and laying 18 mm thick Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand). Note- In order to maintain the slope of the flooring of the room, the extra mortar at the high and of the rooms will have to be provided by the contractor at his own cost.No extra paymet will be made for the extra thickness of mortar provided by the contractor to maintain the minimum slope of the granite flooring. |
| 23 | Supplying & Laying 80mm thick (± 3mm) factory made cement concrete colored interlocking paver block of M – 40 grade confirming to IS – 15658 (minimum compressive strength 400 Kg/Sq.m. & water absorbtion should not be more than 6% by mass) having smooth finish and of approved size and design/shape laid in required colour and pattern over50mm thick compacted bed of Ganga Sand / Natural Sand / Other approved sand and filling the joints with same etc. all complete as per the direction of Engineer-In-Charge. |
| 24 | Supply, fabrication and erection of Commercial grade structural steel used for general fabrication work including \"handling, Marking, cutting, grinding, fit-up, welding, and thereafter applying one coat of Red Oxide primer (Berger/Asian/ Nerolac) & two coats of S.E. paint (Berger/ Asian/Nerolac) on structural steels, fencing, ornamental grills, & Ladders etc. at various location. All consumables like Welding Electrodes, gas, grinding wheels and other consumables including T&P is in the scope of contractor. |
| 25 | Supplying and fixing 0.45mm (Approx.) Galvalume profile Sheet of M/S TATA, M/S Jindal, M/S Bhushan make, fixing over roofing including Sheet for drain, G.I.\"J\" or\"U\" bolts & nuts 8mm diameter with bitumen & G.I. washers to be fixing over existing purlins etc. including fixing of wind ties and colour. Note: No Overlapping will be paid. |
| 26 | Providing & laying integral cement based waterproofing treatment including preparation of surface as required for treatment of roofs including dismantling of existing waterproofing (Brickbat tiles with mud phaska etc.) upto slab level of balconies, terraces, chajjas etc. consisting of the following: -(1) Applying & grouting a slurry coat of neat cement using 2.75 kg/SqM of cement admixed with approved water proofing compound over RCC slab including cleaning the surface before treatment. (2) Laying brick bats/Broken bricks25mm to 115 mm size withcement mortar 1:5 (1 cement: 5 coarse sand) admixed withapproved water proofing compoundover 20 mm thick layer of cement mortar 1:5 (1 cement: 5 coarse sand) admixed withapproved water proofing compoundto required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (3) After two days of proper curing, applying a second coat of cement slurry 2.75 kg/sqm of cement admixed with water proofing compound(4) Finishing the surface with 20mm thick joint less cement mortar of mix 1:4 admixed with approved water proofing compoundand finally finishing the surface with trowel and neat cement slurry and making false marking of size 300X300 mm square 3 mm deep.(5) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test of all the above operations to be done in presence of Engineer-In-Charge. (6) With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 7)Dismantling of existing waterproofing including removal of mud phaska, brick tiles, mortar, concrete, pointing etc. upto roof slabe level at terrace and disposal of above upto lead of 10 km will lie under the scope of the Contractor and no extra payment will be made separately. |
| 27 | Providing and laying Heavy duty APP membraneof modified polymer of Pidilite / Texsa / S.T.P make reinforced with polyster mat in minimum 3mm thickness conforming to specification (without any mineral finish) including preparation of surface as required for treatment of roofs, over coat ofbitumen primer with minimum coverage of 0.40 litre/SqM of make Berger,Asian, Nerolac, jointing the strips and bottom by torch welding, minimum overlapping joints at side and ends of strips shall be 100 mm and 75 mm respectively, rolling, finish with super silver shield of make STP limited / Makphalt for roofs and parapet including testing of the treatment as per specification for water tightness as per instruction of Engineer, overlapping will not be paid seperately, including repairing of expansion joint with polysulphide as per requirement. Note- 1) If leakage is observed from the APP membrane portion, contractor will have to remove and relay the APP membrane at his own cost. 2) Minor surface repair at roof and making of fillet of size 75mm x 75mm at junction of roof and parapet wall with CC 1:2:4 will lie under the scope of Contractor and no extra payment will be made separately. 3) Plastering of the terrace for maintaining uniform slope and level before laying of primer, payment will be made in relevant item. |
| 28 | Attending various maintenancejobs related to maintenance supervisor, Office-cum-site supervisor, Carpentry, Masonry, Plumbing Painting including letter writing ,by providing skilled manpower such as Carpenter, Mason, Plumber and Painter etc. including provididng all necessary tools and tackles and tool Bags for proper completion of jobs at various location as decided by the Engineer-in-Charge. As per relevant clauses of technical specifications. NOTE:(1) Please read clause no. 10.1 of Technical specification for minimum supply of manpower. |
| 29 | Attending various maintenancejobs related to Carpentary, Masonry, Plumbing and other miscellaneous job etc. by providing semi-skilled manpower such as Carpenter, Mason, Plumber, Painter and supervisor etc. including providing all necessary tools and tackles and tool Bags for proper completion of jobs at various location as decided by the Engineer-in-Charge. As per relevant clauses of technical specifications. NOTE:(1) Please read clause no. 10.2 of Technical specification for minimum supply of manpower. |
| 30 | Assistance in attending complaints of various trades as mentioned in item 25 & 26 above and other works as directed by Engineer. As per relevant clauses oftechnical specifications. NOTE:(1) Please read clause no. 10.3 of Technical specification for minimum supply of manpower. |
| 31 | Providing services of skilled data entry operator for office work including operating computer systems, preparing data entry sheets, maintaining records, generating reports, scaning, printing and performing other miscellaneous work all as per direction of EIC. |
| 32 | Hiring of Hydra Crane (at least 30 ft. boom) (including driver, diesel and all T& P) for safely felling / displacement / removal of cut main trunk / branches of trees of any girth, shielding from overhead lines and cables , garages, residential quarters etc. using jacking arrangement as required, assisting the whole operation, safe transportation of cut branches to store / upto 10 km. lead etc. all as per site conditions and as per direction of Engineer-In-Charge. |
| 33 | Supply, laying & compacting the earth, brought from outer side (i.e. not from the excavated site it self) for filling side of road etc., the layers not exceeding 150mm in thickness watering, compaction by ramming, compactor, roller etc. as requiredand consolidation etc. disposing surplus earth as per directed by Engineer-In-Charge. |
| 34 | Cleaning and removal of spider webs, cobwebs, and dust from ceilings (plain or inclined), walls, beams, trusses, columns, windows, doors, chajja, fans, electrical fittings, and other surfaces at all heights using suitable tools such as long-handle brushes, brooms, dry/wet cloth, and vacuum cleaner, including providing and fixing necessary scaffolding, ladders, or working platforms wherever required, and safe disposal of removed material to location within 10 km lead, with monthly operation as directed by the Engineer-in-Charge.The work shall be carried out carefully without causing damage to existing finishes, fittings, or structures, and shall include all labour, materials, tools, plants, scaffolding, and safety arrangements complete as per direction of the Engineer-in-Charge. Note: 1) Clearance from safety department is to be obtained before execution of the work. 2) Use of PPE, height pass, etc. is to be ensured. |
| 35 | PART-II : Supply Items |
| 36 | Stainless steel Towel rail 600mm long. (Min weight 500gm ±50gm) |
| 37 | CP drawer knob 50mm (Minimum 15 Gm Weight) |
| 38 | Hydraulic door closer conforming to Designation No.3 universal type of IS 3564 make Godrej/Everite. |
| 39 | MS door handle 100mm long of Pressed oval type with stove enamelled black finish conforming to IS 208 |
| 40 | M.S. butt hinges 125mm long ISI mark weight 180 gram each ±5 gram. |
| 41 | M.S. butt hinges 100mm long ISI mark weight 120 gram each ±5 gram. |
| 42 | M.S. butt hinges 75mm long ISI mark weight 60 gram each ±5gram. |
| 43 | M.S. hasp & staple (Chhapka Kunda) safety type 150mm±2 mm long |
| 44 | Stainless Steel hanging type door stopper with Twin rubber & stopper heavy duty 75mm long.Min weight 110gm ± 10 gm |
| 45 | Oxidised mild steel single acting spring hinges 150 mm long. |
| 46 | Oxidised mild steel single acting spring hinges 100 mmlong. |
| 47 | Chrome Finish M.S. Tower bolt 8 mm dia rod 100mm long weight 75 gm minimum. |
| 48 | Chrome Finish M.S. Tower bolt 8 mm dia rod 150mm long weight 135 gm. |
| 49 | Chrome Finish M.S. Tower bolt 8 mm dia rod 250mm long weight 155 gm. |
| 50 | M.S. Door safety chain (heavy duty chain with lock button) weight 55 gm. |
| 51 | M.S. pelmet hanger flat minimum size (15 x 120) mm (patti). |
| 52 | SS Screw 35 mm x 8 mm (Each packet contain 100 Nos.) confirm to IS 6760 |
| 53 | SS Screw 30 mm x 7 mm (Each packet contain 100 Nos.) confirm to IS 6760 |
| 54 | SS Screw 20 mm x 5 mm (Each packet contain 100 Nos.) confirm to IS 6760 |
| 55 | Chrome finish MS brackets for Curtain rod with 20mm dia threadedsockets. |
| 56 | Aluminium heavy duty curtain pipe 19 mm dia min 1.57mm thick wall. |
| 57 | Stainless Steel 304 grade curtain rod 20 mm dia and 1.2 mm thickness. |
| 58 | Stainless Steel cloth hanger with 5 hooks fixer with flat 325mm long. |
| 59 | Godrej night latch 7 levers for inside / outside opening doors with 3 keys. |
| 60 | Brass Mortice latch and lock 100X65 mm with 6 lever and pair of brass lever handle body in golden colour |
| 61 | Door viewer 35mm to 50mm long. |
| 62 | PTMT Symet Shelf for washbasin of Prayag / Polytuf make. |
| 63 | Mirror 5mm thick size 450mm x 300mm having 4 holes at corner of Modigard/ Sant Gobain/ Atul make |
| 64 | Mirror beveled edge 5mm thick size 600 x 450mm having 4 holes at corner of Modi Gard/ Atul/ Sant Gobain make. |
| 65 | Double action hydraulically operated floor spring medium size (11.5\" x 6.75\" x 2.5\") ISI Mark . |
| 66 | Commercial plywood 4mm thick size: 2440 x 1220mm of M/S Century or Duro make conform to IS:303 of BWP Grade |
| 67 | Commercial plywood 6mm thick size: 2440 x 1220mm of M/S Century or Duro make conform to IS:303 of BWP Grade |
| 68 | Commercial plywood 12mm thick size: 2440 x 1220mm of M/S Century or Duro make conform to IS:303 of BWP Grade |
| 69 | Commercial blockboard 19mm thick size: 2440 x 1220mm of M/S Century or Duro make conform to IS:1659 of BWP Grade |
| 70 | Flush door shutters 35 mm thick of M/S Century / DURO make conform to IS:1659 of BWP Grade |
| 71 | 32mm thick seasoned Sheeshum wood panel door shutter with 18mm thick Sheeshum wood planks withlock rail 150 mm, top and side style 100mm width, bottom 150mm complete as per existing pattern. |
| 72 | Seasoned Sheeshum wood window shutter frame of 62mm X 32mm section smooth finishing & making 10mm X 10mm groove for glass fixing with beading. |
| 73 | 32mm thick seasoned Sheeshum wooden jali shutter of bottom rail 150 mm and other 100 mm, existing pattern using Stainless Steel wire 0.46 mm dia and having approximately 14 mesh in one linear inch. |
| 74 | Fevicol SH synthetic resin adhesive in 1 kgpack. |
| 75 | Fevicol SR 998 1 litrepack. |
| 76 | Fevicol Probond 1 kg pack. |
| 77 | Fevicol Heatx 1 liter pack |
| 78 | Season sheeshum wood |
| 79 | Factory made Solid WPC (Wood Polymer Composite) door chowkhat of section 100 mm X 65 mm, single rebate frame made of termite-proof and water proof WPC material with smooth finish with minimum density of 750kg/cum of make Alstone, Ecoste, Century. Material TC is to submitted. |
| 80 | Factory made Solid WPC (Wood Polymer Composite) door chowkat of section 125 mm X 65 mm, double rebate, frame made of termite-proof and water proof WPC material with smooth finish with minimum density of 750 kg/cum of make Alstone, Ecoste, Century WPC. Material TC is to submitted. |
| 81 | Factory made Solid WPC (Wood Polymer Composite) door chowkat of section 70 mm X 45 mm, single rebate, frame made of termite-proof and water proof WPC material with smooth finish with minimum density of 750 kg/cum of make Alstone, Ecoste, Century WPC. Material TC is to submitted. |
| 82 | Factory made 35 mm thick WPC flush door shutter, made of solid wood polymer composite board of make Alstone, Ecoste, Centuryof minimun density 650 kg/m3, waterproof, termite-proof, with smooth factory finish and machine trimmed edges of make Alstone, Ecoste, Century WPC. TC of material is to submitted. Sample will be approved by EIC for style and rails before fixing at site. |
| 83 | Stainless steel anchor Fastners Brick M-10 X 100 mm |
| 84 | Helicol Spring Hinges |
| 85 | Chrome Finish MS Aldrop set -300mm long with nut bolt weight 750 gm ± 20 gm . |
| 86 | CP Brass grating 125mm dia having 6mm hole weight 60 gm ± 5 gm. |
| 87 | CP Brass DOME grating 125mm dia and 25mm dia waste hole weight 60 gm ± 5 gm. |
| 88 | C.P. Brass Bib taps15mm n.b Weight 400 gm ± 20 gm make K K GOLD/K K / SHREE/ SUPERTECH. |
| 89 | C.P. Brass Stop cock 15mm n.b Weight 400 gm ± 20 gm make K K GOLD / K K / SHREE / SUPERTECH. |
| 90 | CP Brass long body bib tap 15mm n.b Weight 400 gm ± 20 gm make K K GOLD / K K /SHREE / SUPERTECH. |
| 91 | C.P. Brass Pillar cock 15mm n.b Weight 580 gm ± 20 gm make SEECO/SHREE/KK GOLD/KK/SUPERTECH. |
| 92 | C.P. Brass Push Cock 15mm n.b weight 250 gm ± 20 gm make K K GOLD / K K / SHREE / SUPERTECH. |
| 93 | Angle Cock size 15mm of K K GOLD / K K / SHREE / SUPERTECH make. |
| 94 | C.P. Angle valve Make Seeco |
| 95 | C.P. Three way swan cock |
| 96 | C.P. Brass Round overhead swerving shower rose 100 mm dia heavy duty size 15mm |
| 97 | C.P. brass waste Coupling 32mm dia , 75mm long for Wash Basin Weight 125 Gram ± 10 Gram. |
| 98 | C.P. brass waste Coupling 32mm dia , 75mm long for Sink Weight 125 Gram ± 10 Gram. |
| 99 | C.P. Waste Coupling 32mm dia for wash basin make Jaquar (Cat. No.: ALD-705) /Hindware (Cat. No.: F850002). |
| 100 | C.P. Waste Coupling 40mm dia for wash basin. |
| 101 | C.P Wall Mixer of Jaquar (Product Code: CON-CHR-219KN) or Hindware (Cat. No.: F740019) make. |
| 102 | C.P Central Hole Wash Basin Mixer of Jaquar(Product Code: CON-CHR-167KNB) or Hindware (Cat. No.: F330014CP) make. |
| 103 | SS Hand shower 15 mm dia with 1.5 mtr. flexible pipe for WC (Min. weight 250gm) |
| 104 | C.P. Brass Extension Nipple 15mmX50mm size |
| 105 | C.P R-Extension Nipple 3/4\" X 1/2\". |
| 106 | C.P. Telephonic Bathroom wall Mixerof Jaquar (Cat. No. QQT - 7217). |
| 107 | C.P.Bottel trap Make Hindware (Cat. No.: F850015) / Jaguar (Cat. No. ALD-CHR-769L / ALD-769L) |
| 108 | C.P. Flush Valve Make Cera (Cat. No. F8010301) / Jaguar (Cat. No. FLV-CHR-1015NEL / FLV-1015NEL) |
| 109 | C.P. Z Type Extention Nipple / leg 15mmx20mm (Full Size) |
| 110 | C.P. Z Type Extention Nippel / leg 20mmx25mm (Full Size) |
| 111 | C.P. Brass bib cock jumper valve washer(Each packet contain 100 nos.) |
| 112 | C.P. Soap Dish make jaguar (Cat. No. CAN-1131N or Parryware (Cat. No. T6503A1) |
| 113 | C.P. Toilet paper holder make jaguar (Cat. No. ACN-CHR-1151N or Hindware(Cat. No.: F450027) |
| 114 | Gun Metal non-return valve - vertical (screwed end) size 15 mm Leader or Sant make screwed female ends with ISI mark . |
| 115 | Gun Metal non-return valve - horizontal (screwed end) size 15 mm Leader or Sant make screwed female ends with ISI mark . |
| 116 | Gun Metal non-return valve - vertical (screwed end) size 20 mm Leader or Sant make screwed female ends with ISI mark . |
| 117 | Gun Metal non-return valve - horizontal (screwed end) size 20 mm Leader or Sant make screwed female ends with ISI mark . |
| 118 | Gun Metal non-return valve - vertical(screwed end) size 25 mm Leader or Sant make screwed female ends with ISI mark . |
| 119 | Gun Metal non-return valve - horrizontal (screwed end) size 25 mm Leader or Sant make screwed female ends with ISI mark . |
| 120 | Gun Metal Gate Valve size 15 mm Leader or Sant make screwed female ends with ISI mark inside thread 6 Kg/CMSQ. |
| 121 | Gun Metal Gate Valve size 20 mm Leader or Sant make screwed female ends with ISI mark inside thread 6 Kg/CMSQ. |
| 122 | Gun Metal Gate Valve size 25 mm Leader or Sant make screwed female ends with ISI mark inside thread 6 Kg/CMSQ. |
| 123 | Gun Metal Gate Valve size 40 mm Leader or Sant make screwed female ends with ISI mark inside thread 6 Kg/CMSQ. |
| 124 | GI pipe class \"B\" confirming to IS-1239 with one end socket and other protect with PVC cap of make TATA / JINDAL/ SWASTIK of dia 15 mm |
| 125 | GI pipe class \"B\" confirming to IS-1239 with one end socket and other protect with PVC cap of make TATA / JINDAL/ SWASTIK of dia 20mm. |
| 126 | GI pipe class \"B\" confirming to IS-1239 with one end socket and other protect with PVC cap of make TATA / JINDAL/ SWASTIK of dia 25mm. |
| 127 | G.I. Socket 15mm dia of make UNIK/SARIN/DRP/YASH. |
| 128 | G.I. Socket 20mm dia of make UNIK/SARIN/DRP/YASH. |
| 129 | G.I. Socket 25mm dia of make UNIK/SARIN/DRP/YASH. |
| 130 | G.I. Socket 32mm dia of make UNIK/SARIN/DRP/YASH. |
| 131 | G.I. Reducer Socket 20 X 15mm of make UNIK/SARIN/DRP/YASH. |
| 132 | G.I. Reducing Socket 25 mm x 15 mm of makeUNIK/SARIN/DRP/YASH |
| 133 | G.I. Reducer Socket 25 mm x 20 mm of makeUNIK/SARIN/DRP/YASH |
| 134 | G.I. Reducer Socket 32 mm x 25 mm of makeUNIK/SARIN/DRP/YASH |
| 135 | G..I Reducer Socket 40 X 32mm of make UNIK/SARIN/DRP/YASH. |
| 136 | G.I. Reducer Socket 50 mm x 20 mm of makeUNIK/SARIN/DRP/YASH |
| 137 | G.I. Reducer Socket 50 mm x 25 mm of makeUNIK/SARIN/DRP/YASH |
| 138 | G.I. Reducer Socket 50 mm x 32 mm of makeUNIK/SARIN/DRP/YASH |
| 139 | G.I. Elbow 15mm dia of make UNIK/SARIN/DRP/YASH. |
| 140 | G.I. Elbow 20mm dia of make UNIK/SARIN/DRP/YASH. |
| 141 | G.I. Elbow 25mm dia of make UNIK/SARIN/DRP/YASH. |
| 142 | G.I. Elbow 32mm dia of make UNIK/SARIN/DRP/YASH. |
| 143 | G.I. Reducing Elbow 20mm X 15mm of make UNIK/SARIN/DRP/YASH. |
| 144 | G.I. Reducing Elbow 25mm X 15mm of make UNIK/SARIN/DRP/YASH. |
| 145 | G.I. Reducing Elbow 25mm X 20mm of make UNIK/SARIN/DRP/YASH. |
| 146 | G.I. Reducing Elbow 32 mm x 25 mm of makeUNIK/SARIN/DRP/YASH |
| 147 | G.I. Tee 15mm dia of make UNIK/SARIN/DRP/YASH |
| 148 | G.I. Tee 20mm dia of make UNIK/SARIN/DRP/YASH |
| 149 | G.I. Tee 25mm dia of make UNIK/SARIN/DRP/YASH. |
| 150 | G.I. Reducing Tee 20 mm x 15 mm dia of make UNIK/SARIN/DRP/YASH. |
| 151 | G.I. Reducing Tee 32 mm x 20 mm dia of make UNIK/SARIN/DRP/YASH. |
| 152 | G.I. Union 15mm dia of make UNIK/SARIN/DRP/YASH. |
| 153 | G.I. Union 20mm dia of make UNIK/SARIN/DRP/YASH. |
| 154 | G.I. Union 25mm dia of make UNIK/SARIN/DRP/YASH. |
| 155 | GI Union 32 mm of makeUNIK/SARIN/DRP/YASH |
| 156 | G.I. Nipple15mm dia 50mm long. |
| 157 | G.I. Nipple15mm dia 100mm long. |
| 158 | G.I. Nipple20mm dia 100mm long. |
| 159 | G.I. Nipple25mm dia 100mm long. |
| 160 | G.I. Nipple32mm dia 100mm long. |
| 161 | G.I. Cross 15mm dia of makeUNIK/SARIN/DRP/YASH |
| 162 | G.I. Cross 20mm dia of makeUNIK/SARIN/DRP/YASH |
| 163 | G.I. Cross 25mm dia of makeUNIK/SARIN/DRP/YASH |
| 164 | G.I. Bend pipe 32mm dia |
| 165 | G.I. Flush Pipe 32mm dia. |
| 166 | M.S. Hex Nipple 15MM DIA. |
| 167 | M.S. Hex Nipple 20MM DIA. |
| 168 | M.S. Hex Nipple 25MM DIA. |
| 169 | M.S. Hex Nipple 32MM DIA. |
| 170 | M.S. Plug 15mm dia. |
| 171 | M.S. Plug 20mm dia. |
| 172 | M.S. Plug 25mm dia. |
| 173 | MS hookfor GI Pipe. |
| 174 | GI Saddle clamp for GI Pipe of all size |
| 175 | PVC Saddle clip clamp for UPVC Pipe for 110mm pipe |
| 176 | M.S. Flush Chain |
| 177 | M.S. nails all types |
| 178 | PTMT Symet Bib Tab 15mm size of Prayag / Supreme make. |
| 179 | PTMT Symet Float Valve with Ball 15mm size complete set of Prayag / Suprememake |
| 180 | PTMT Symet Float Valve with Ball 20mm sizecomplete set of Prayag / Supreme make |
| 181 | PTMT Symet Float Valve with Ball 25mm sizecomplete set of Prayag/Supreme make |
| 182 | PTMT Symet Float Valve with Ball 32mm size complete set of Prayag/Supreme make |
| 183 | 15mm epoxy coated alumium rod for PTMT Float valve make Prayag/Supreme |
| 184 | 20 mm epoxy coated alumium rod for PTMT Float valve make Prayag/Supreme |
| 185 | 32mm epoxy coated alumium rod for PTMT Float valve make Prayag/Supreme |
| 186 | Unplasticised PVC connection pipe with brass union 45cm long 15mm bore for Hot and cold water |
| 187 | Stainless steel braided connection pipe with union 45cm long 15mm bore for Hot water |
| 188 | Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 900 mm |
| 189 | PTMT Bottle Trap size 32mm dia. |
| 190 | PVC Low Level Cistern of approx. 10 lit. capacity of HINDWARE / PARRYWARE / CERA /KOHLAR make. |
| 191 | PTMT Symet Liquid Soap Container Prayag / Polytuf make . |
| 192 | P.V.C. Long Bend 32mm dia for cistern |
| 193 | Exposed part kit of Concealed Stop Cock with Fitting Sleeve,Operating Lever & Adjustable wall Flange of make Jaguar & Marc. |
| 194 | Stainless steel Flexible tube/Hose for shower 1.5m long with nuts of make Jaguar/Marc/Seeco. |
| 195 | Single Action elbow lever Bib cock of make Jaguar/Marc |
| 196 | Bib Cock of make Jaguar (Cat. QQT-CHR-7037) |
| 197 | OWC China ware white glazed size 580 X 440mm of make PERRYWARE/ CERA/HINDWARE/VARMORA. |
| 198 | Nylon washer for C.P. brass pillar cock & stopcock (100 Nos each packet) |
| 199 | Toilet Jet spray silver with 1.5 m heavy PVC Hose set. |
| 200 | Vitreous china flat back Wash Basin of size 450x300mm of HINDWARE/PARRYWARE / CERA/KOHLAR/ VARMORA make with required fixture |
| 201 | Vitreous china flat back Wash Basin of size 550x400mm of HINDWARE/PARRYWARE / CERA/KOHLAR/ VARMORA makEwith required fixture. |
| 202 | White vitreous china clay half stall urinal flat back 580x380x350 mm of HINDWARE/PARRYWARE / CERA/KOHLAR/ VARMORA make |
| 203 | Round shape single flow hand shower of Jaquar (Product Code: HSH-CHR-1937)or Marc (Product Code: MVT-2120) make. |
| 204 | Round shape single flow Overhead shower of Jaquar with Shower arm of Jaquar/Marc make. |
| 205 | Chinaware \"P\" Trap 100 mm dia for OWC of Standard depth. |
| 206 | EWCwhite glazed with P/S trap of HINDWARE/ PARRYWARE / CERA/KOHLAR/VARMORA make |
| 207 | EWC Seat Cover (White) |
| 208 | Wall Vit Pan with Bracket HINDWARE/PARRYWARE / CERA/KOHLAR/ VARMORA MAKE |
| 209 | Cooper Tube 8 mm |
| 210 | Brass Checknut 40mm x 32mm |
| 211 | Chinawear Laboraroty White Sink of Size 600 x 400 x200 mm of make Cera / Parryware / Hindware. |
| 212 | Chinawear Urinal Pot Size 44 cm x 26.5 cm x 35.5 cm of HINDWARE/ PARRYWARE / CERA/KOHLAR/ VARMORA mak |
| 213 | Unplasticised Polyvinyl Chloride (UPVC) SWR pipes 50mm(conforming to IS 13592-Type B ) of working pressure rating 4 Kg/cm2 (make- SUPREME / ASTRAL / PRINCE) |
| 214 | Unplasticised Polyvinyl Chloride (UPVC) SWR pipes 110mm(conforming to IS 13592-Type B ) of working pressure rating 4 Kg/cm2 (make- SUPREME / ASTRAL / PRINCE) |
| 215 | UPVC Waste trap(Nahani trap) 75mm confirm to IS 14735 |
| 216 | UPVC Waste trap(Nahani trap) 110mm confirm to IS 14735 |
| 217 | UPVC bend 90Owithinspection doors 75mm confirm to IS 14735 for SWR |
| 218 | UPVC bend 90O with inspection doors 110mm confirm to IS 14735 for SWR |
| 219 | P.V.C. Socket 110mm dia for SWR |
| 220 | UPVC Tee110mm confirm to IS 14735 for SWR |
| 221 | UPVCReducer Socket 110mm x 90mm for SWR |
| 222 | UPVC Cowl 110mm confirm to IS 14735 for SWR |
| 223 | Solvent Cement confirming to ASTM F493 in 100ml packaging |
| 224 | Dhaga for plumbing work (20 Nos each packet) |
| 225 | Safeda for plumbing workin 100 Grampack make Astral,M-seal |
| 226 | Polyethylene cylinderical vertical water storage tank of capacity 2000 Liters conform to IS:12701with cover and suitable locking arrangement |
| 227 | Polyethylene cylindrical vertical water storage tank of capacity 1000 Liters conform to IS:12701 with cover and suitable locking arrangement |
| 228 | Polyethylene cylindrical vertical water storage tank of capacity 5000 Liters conform to IS:12701 with cover and suitable locking arrangement |
| 229 | Polyethylene cylinderical vertical water storage tank of capacity 500 Liters conform to IS:12701 with cover and suitable locking arrangement |
| 230 | Single Piece Conceal Cistern of Jaquar with installation kit for wall hung WC (Without Flush control Plate)(Cat. JCS-WHT-2400). |
| 231 | Brass Concealed Face as per sample available in Civil Store |
| 232 | OPC Cement of 43 grade(50Kg.bags) in phased manner as per the requirement of Engineer-in-charge including unloading and stacking in civil maintenance store. Cement shall be any one of M/s Gujrat Ambuja, Ultra Tech, Birla Uttam & JK Super cement Brand. |
| 233 | Araldite Gy 257 make HUNTSMAN |
| 234 | Hardner Aradur 140 make HUNTSMAN |
| 235 | Silica Sand |
| 236 | Haldwani Sand FM not less than 2.30 |
| 237 | White Cement (Each packet contain 1Kg.) |
| 238 | Stone aggregate 10 / 12.5 mm size |
| 239 | Intergal waterproofing compound of make Dr. Fixit/Sika/Asian Paint/Fosroc in 1Liter packaging as approved by Engineer-In-Charge. |
| 240 | Waterproofing coating system of make HS PU Roofkoat of M/S Berger or smart care damp proof Ultra of M/S Asian Paint or Dr. Fixit Roof seal classic of M/S Dr. Fixit. |
| 241 | AC Sheet of 6 mm thick (Average)of M/S Everest / Uppal / Charminar / JP make |
| 242 | G.I. J\" or \"U\" bolts & nuts 8mm diameter with bitumen & G.I. washers |
| 243 | Welding electrode 2.5 mm dia code - 6013. (Each packet contain 110 electrods) |
| 244 | Barbed Wire |
| 245 | Punched tape concertina coil 600 mmdia 10 m openable length. |
| 246 | RBT reinforced barbed wire |
| 247 | Rubber choke remover (Butach) with handle & rubber size 125mm dia. |
| 248 | Lime Powder. |
| 249 | Digital Vernier caliper size 150 mm with calibration report from NABL approved lab |
| 250 | Rubber Gasket U-type for aluminum door and window |
| 251 | Plain Acrylic Sheet 5mm thick, Size (8x4) feet. |
| 252 | 65 mm steel pad lock with 3 keys of make link / Hindson / Harison. |
| 253 | M-seal (Fast curing epoxy compound) |
| 254 | Heavy duty swing rubber seat with SS huck handle of size 30\" x 7.5\" x 10mm |
