|
| 1 | Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying of cable and foundation of poles, stays etc. n exc 10 sq m on plan and not exceeding 1.5 m in depth and getting out in hard/dense soil, complete all as specified and as directed by Engineer-in-Charge. |
| 2 | M&L for plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete, complete all as specifiedas directed by the Engineer-in-Charge. |
| 3 | M&L for pre-cast cement concrete block masonry 1:3:6type C1(using 20mm graded stone aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 complete all asspecified and directedby Engr-in-charge. |
| 4 | M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in surface channel and drains complete all as specifiedas directed by the Engineer-in-Charge. |
| 5 | M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping, roof kerbs, mudstops apex stone, bed plate,rounded or chamfered on edgesincluding form work complete all as specifiedas directed by the Engineer-in-Charge. |
| 6 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each layer in any type of soil complete all as specified and as directed by Engineer-in-Charge. |
| 7 | Removing excavated material not exceeding 50metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and as directed by Engineer-in-Charge. |
| 8 | M&L for rendering 15mm thick on fair faces of brick work orconcrete surfacesin cement mortar 1:4, surface finished even and smooth without using extra cement as in wall,complete all as specified and directed by the Engineer-in-Charge. |
| 9 | M&L for rendering 10mm thick on fair faces of brick work orconcrete surfacesin cement mortar 1:4, surface finished even and smooth without using extra cement as in wall,complete all as specified and directed by the Engineer-in-Charge. |
| 10 | M&L for rendering 5mm thick on fair faces of brick work orconcrete surfacesin cement mortar 1:3, surface finished even and smooth without using extra cement as in ceiling,complete all as specified and directed by the Engineer-in-Charge. |
| 11 | M&L for providing and applying plaster of paris putty of 2 mm thickness over plastered / concrete surfaces to prepare the surface even and smoothcomplete all as specified and directed. |
| 12 | M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes 300mm bore, laid to falls including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed by Engineer-in-Charge. |
| 13 | M&L for 300mm bore reinforced concrete pipes with coller, Class NP2, laid in trenches and jointed in CM 1:1 and tested, complete all as specified and directed. |
| 14 | Taking down plastering in cementlimeor cement mortoron brick or stone work etc. includingracking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed by the Engineer-in-Charge. |
| 15 | M&L for rendering 10mm thick on fair faces of brick work orconcrete surfacesin cement mortar 1:6, surface finished even and smooth without using extra cement,complete all as specified and directed by the Engineer-in-Charge. |
| 16 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfacesin cement mortar 1:4 by using water proofing compound @ 3% by weight of cement or as per manufacturer instruction, surface finished even and smooth without using extra cement,complete all as specified and directed by the Engineer-in-Charge. |
| 17 | Supply only integral water proofing compound. |
| 18 | S & F for framed work as in door or gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering for door or guard bar to be prepaired for hanging or sliding with and including either hooks and hinges or steel hanging sheeting or other covering running rails and guides) and hanging also for Fe-410-W (Gde-E-250) quality A complete all as specified and directed by the Engineer-in-Charge. |
| 19 | S&F steel door including projectingtype hinges, steelhandle, complete,with glazing bars, dovetailed orwelded complete all as specified and directed by the Engineer-in-Charge. |
| 20 | S&F steel windows with side hungshutters including projecting typehinges with steel handle, and steel peg stay,complete with glazing bars, dovetailed or welded complete all as specified and directed by the Engineer-in-Charge. |
| 21 | S&F Sheet glass 4mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by the Engineer-in-Charge. |
| 22 | S&F preparation of newly untreated steel or iron surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate,complete all as specified and as directed. |
| 23 | S&F preparation of old steel painted surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and as directed. |
| 24 | M&L for Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified. |
| 25 | M&L for reinforced cement concrete nominal mix 1:2:4 type B1using 20mm graded stone aggregates in lintel beams complete all as specified and directed. |
| 26 | Use and waste of formwork to side and soffits of lintel beam with flat rough finished surface complete all as specified and directed. |
| 27 | M&L TMT steel bars10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specifiedas directed by the Engineer-in-Charge. |
| 28 | M&L for 100mm thick plain cement concrete 1:2:4 type B-1(using 20mm graded stone aggregates) as in floor finishing the surface even and fair without using extra cement complete all as spd and directed. |
| 29 | Forming Contraction (Dummy) joints 100mm deep x 10mm wide, filled with sealing compound complete all as spd and directed. |
| 30 | Forming 12mm thick Expansion joints filledwith pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as spd and directed. |
| 31 | M&L for preparation of new/oldplastered surface of wall and applying two or more coats of 1st class quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour as permanufacturer\"s instruction complete all as spd and directed. |
| 32 | M&L for preparation of new/oldplastered surface of wall and applying two or more coats ofAcrylic Smooth exterior paint of required shade : (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), as in camoflouge patternall as specified and as directed by Engineer-in-charge. |
| 33 | M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as spd and directed. |
| 34 | S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as spd and directed. |
| 35 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 36 | M&L for vitrified ceramic tiles dark shade 10mm thick (square or rectangular) double charged/ultracharged, polishedarea of each tile exceeding 0.36sqm, but not exceeding 0.42 sqm as in floors etc. set and jointedin neatcementslurry and pointed in white or coloured cement to match the shade of tiles, laid over and including15mm thick screed bed or bedding layer in cement mortar1:6, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by AGE BR and contractor shall not have any claim whatsoever on this account.complete all as spd and directed. |
| 37 | M&L for Non skid ceramic coloured tiles Ist quality7 to 8mm thick, (square/ rectangular), area of each tile exceeding 0.06sqm, but not exceeding 0.11sqm as in floors etc. set and jointedin neatcementslurry and pointed in white or coloured cement to match the shade of tiles, laid over and including15mm thick screed bed or bedding layer in cement mortar1:6, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by AGE BR and contractor shall not have any claim whatsoever on this account.complete all as spd and directed. |
| 38 | M&L for Glazed ceramic tiles, coloured, of size350mm x 250mm/450 mm x 350mm, thickness not less than 7mm as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and including 10mm thick rendering (bedding layer) on brick/concrete surface in cement mortor 1:4, complete all as specified and as directed by the Engineer-in-Charge.Note: Colour and shade of tiles shall be approved by AGE BR and contractor shall not have any claim whatsoever on this account.complete all as spd and directed. |
| 39 | M&L for providing precast cement concrete 1:2:4 type B1using 20mm graded stone aggregate and set in Cement Mortar 1:4 as in window or door cills, lintels, bressumers, steps, quoin blocks complete all as spd and directed. |
| 40 | M&L for preparation of newsurfacesof wall and applying three coats ofwhite washall as specified and directed. |
| 41 | S&Fsolid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening complete all as spd and directed. |
| 42 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as spd and directed. |
| 43 | S&F 75mm long stainless steelbutt hinges and fixed to frame with scrwewd or welding complete all as spd and directed. |
| 44 | S&F for 200mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as spd and directed. |
| 45 | S&F for 150mm long aluminium handle cast type anodized all as specified and as directed by Engineer-in-Charge. |
| 46 | S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 47 | S&F 20mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 48 | S&F 1000 ltrs PVC rotational moulded polyethylene water storage tanks triple layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I complete all as spd and directed. |
| 49 | S&F ball float valve PTMT with epoxy coated aluminimum rodfor 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe, complete all as specified and directed. |
| 50 | S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixedcomplete all as specified and directed. |
| 51 | S&F in repairVitreous china wash hand basin (550X400mm) white, flat back excluding taps,including brackets & 32mm waste cuppling complete all as specifed and directed. |
| 52 | S&F Vitreous China wash down Water closet pan (pedestal pattern) \"with plastic water closet seatcover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairs, complete all as specified and directed. |
| 53 | S&F health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position, complete all as specified and directed. |
| 54 | S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern., complete all as specified and directed. |
| 55 | S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as spd and directed. |
| 56 | S&F Vitreous China Urinal, Half stall type, white (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste complete all as spd and directed. |
| 57 | S&F Grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as spd and directed. |
| 58 | S&F 32mm brass chromium plated waste coupling for wash hand basin all as specified. |
| 59 | S&F15mm dia fancy type pillar tapscast copper alloy with capstan heads chromium plated scewed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts screwed for iron pipe fixed , complete all as specified and directed. |
| 60 | S&F 15mm dia Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule, complete all as specified and directed. |
| 61 | S&F 15mm dia stop valves/angle valve chromium plated, fancy type with long shank and cupscrewed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified, complete all as specified and directed. |
| 62 | S&F 15mm PVC connection 600mm long with PTMT nuts of superior quality as specified, complete all as specified and directed. |
| 63 | S&F tubular towel rail chromium plated20mm dia, D type, 60 cm long with brackets, complete all as specified and directed. |
| 64 | S&F 600x450 bevelled edged looking mirror 2mm thick of selected quality glass, mounted on 4 mm thick PVC sheet and with aluminnium frame work fitted with chromium plated brass screws and cup washers , complete all as specified and directed. |
| 65 | S & FSoap dish, any type, fixed to plugs with chromium plated brass screws complete all as spd and directed. |
| 66 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket tc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,luminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 67 | S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with powder coated aluminium beading/wood beading complete all as spd and directed. |
| 68 | S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as spd and directed. |
| 69 | S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as spd and directed. |
| 70 | S&F 75 mm PVC (SWR) Floor trap, plain with grating incl jointing with solvent complete all as spd and directed. |
| 71 | S&F 110 mm PVC (SWR) Floor trap, plain with grating incl jointing with solvent complete all as spd and directed. |
| 72 | S&F Mild steel screw bolts dia 11 to 15 mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 5cmn exc 10cm long complete all as spd and directed. |
| 73 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed by Engr-in-charge |
| 74 | M&L for plain cement concrete 1:2:4 type B-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete, complete all as specifiedas directed by the Engineer-in-Charge. |
| 75 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified and directed by the Engineer-in-Charge. |
| 76 | S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by Engineer-in-Charge, having tensile strength of 550 Mpa as in roof covering/cladding to ridges, valley gutters etc. fixed with self tapping screws,complete all as specified and as directed by the Engineer-in-Charge. |
| 77 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugatedprofile steel sheet 0.50mm thick of colour as approved by Engineer-in-Charge, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws,complete all as specified and as directed by the Engineer-in-Charge. |
| 78 | S & F steel works in tubular trussesas inpost, purline etc including special shape washer, angle cleat, hold fast, gussete plate etc. complete using ERW or induction butt welded tubes conformimg to IS 1161-1979 grade St-240 cut or notched forming holes,without any attachment including drilling,fittings,riveting and or welding or connecting with bolts ans nuts ( incl rivet or nut ams bolt) providing and fitting angle cleats gussete plates etc also for welding plumbing truing up and fixing complete all as specified and directed by the Engineer-in-Charge. |
| 79 | M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 ® , complete all as specified and as directed by the Engr- in- Charge. |
| 80 | S&F pipes 140 mm dia PVC (SWR) half round pipes as eaves gutters in any length with rubber ring joints fixed to GI sheets for rain water collection and conveyance , complete all as specified and as directed by the Engr- in- Charge. |
| 81 | S&F mild steel Plates, 6mm thick,(plain or chequered), Fe 410-W (Gde E - 250) quality - A,channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as spd and directed. |
| 82 | S&F 3mm thick Aluminium Composite Panel as in wall cladding in any shape/ design including aluminium anodised frame work for fixing of panels joints filled with silicon or relevant material complete finishes all as per manufacturer instructions ans standard design practice complete complete all as specified and directed. |
| 83 | Taking down carefully existing bitumen tar felt including coba,plaster of any description over the surface of roof, terraces including flashings and junctions of parapet/curb walls etc and removing of the rubbish to a distance exceeding 500m but nexc 1.00km and depositing where complete all as specified and directed . |
| 84 | M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out, and filling solidly with a hot mixture of bitumen and clean dry and 1:1 ( by weight) complete all as specified and directed . |
| 85 | Material and labour for water proofing treatment with APP based standard membrane over 15 mm thick PCC padding in CM (1:4) in roof with the following courses of treatment for:-(a) Apply bituminous primer (IS 3384) @ 0.40 Lit per sqm of the surface area including cleaning the surfaces completeall as specified.(b)Apply APP plastomeric bitumen based water proofing membranepolyester reinforced (3Kg/Sqm) with 10cm over laps and torch bonded at joints including surface preparation before and after application of treatment as per manufactures instruction complete all as specified. (Make of APP Membrane: Moply FP 3 mm mineral of TEXA/WP Shield 103 PM of SIKA or Equivalent material of BITUNIL/BITUMAT.(c) Over the membrane provide a solar reflective bituminous aluminium paint @ 0.1 Lit/sqm prescribed by manufacturer complete all as specified. |
| 86 | Use and waste of formwork to sides of columns, pillars, piers, posts and struts complete all as specified and directed. |
| 87 | M&L for cutting upto a depth of 3.5cm into concrete/brick wall and trimming surface as required, girth exc. 30 cm including make good surface of cutting in CM 1:3complete all as specified and directed by the Engineer-in-Charge. |
| 88 | M&L for preparation of newly plastered surface of wall and applying two coat of OBD over a coat primer on walls with plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth completeall as specified and as directed by Engineer-in-charge. |
| 89 | S&F factory madeprecast concrete drain covers with frame of size 600mm x 900mmwith anti-slip texture to enhanced safety and medium traffic conditions and securing them over drains in cement concrete 1:2:4 type B1(using 20mm graded stone aggregate) andshall be finished identical to existing finishincluding all necessary pathwork for making drain surface level and secured complete all as spd and directed. |
| 90 | Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, sockets, light fittings, MCB DBs,out let boxes etc.removing material for taking credit and making good disturbed surfaces of walls, floors, ceilings etc,complete all as specified and as directed by Engr-in-charge. |
| 91 | M&L for point wiring in concealed pVC conduitcomplete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 V grade confirming to IS 694 drawn through PVC conduit of suitable sizeheavy grade ISI marked including necessary PVC conduitaccessories, sunken type pressed steel terminal boxes with plastic laminated sheet of approved shade 3mm thick including 1.5 mm PVC insulated flame retardant copper conductor as in continious earth wire ,complete all as specified and as directed by Engr-in-charge. for the following as given below:- |
| 92 | One light& exhaust fan point controlled by one switch . |
| 93 | One socket point 5 amps on same board with other switches, with cable 1.5 sqmm size. |
| 94 | One socket point 5 amps independent board. |
| 95 | -ditto- all as per item No 91 here in before but with 4 Sqmm wire for 15 Amp socket outlet on independent board complete all as spd and directed. |
| 96 | -ditto- all as per item No 91 here in before but with 2.5 Sqmm wire for 15 Amp socket outlet on independent board complete all as spd and directed. |
| 97 | Supply & Fix switch piano flush button single pole one way 5 Amps, 250 V ,complete all as specified and as directed by Engr-in-charge. |
| 98 | Supply and Fix switch piano flush button single pole one way 15 Amps, 250 V,complete all as specified and as directed by Engr-in-charge. |
| 99 | Supply and Fix socketoutlet 2 in 1,6 pin, 5/15Amps flush type 220 V,complete all as specified and as directed by Engr-in-charge. |
| 100 | Supply & fix switch socket combination 2 in 1, 6 Amp flush type 220 V complete all as spd and directed |
| 101 | Supply & fix switch socket combination 3 in 1, 16 Amp flush type 220 V complete all as spd and directed |
| 102 | S&F, in repair ,Ceiling rose, surface bakelite, 65mm x 50mm two to three terminals. ,complete all as specified and as directed by Engr-in-charge. |
| 103 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete includong GI bracket of suitable size of street light complte with fixing on wall withclamping material all as specified and directed. |
| 104 | Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2010 including testing on completion including taking down existing unserviceable earthing complete all as specified. |
| 105 | Supply and fixing of wall mounting fan 450 mm sweeep complete with blades ,and accessories , 230 volts , complete all as specified and directed by Engr in charge. |
| 106 | Supply and fixing of Exhaustfan 450 mm sweeep steel body AC single phase , 230 volts complete with blades , and frame and louvers etc complete all as specified and directed by Engr in charge. |
| 107 | S&F in replacement of batten type LED light fitting 1x18/20 watt 4 feet long including LED tube with driver complete suitable for fixation on wall / roof with body robustcomplete all as specified and directed by engr in charge. |
| 108 | S&F switch socket combination 2 in 1, 6A flush type complete all as spd and directed. |
| 109 | Supply and fixing of Exhaustfan 300 mm sweeep steel body AC single phase , 230 volts complete with blades , and frame and louvers etc complete all as specified and directed by Engr in charge. |
| 110 | Material and labour for sub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade ,FRLS type,PVC insulated,unsheathed,flexible,multi stranded duly colour coded cable drawn through and including PVC casing and caping of size 25mm width or above as required at site and accessories such as tee, corners, overlapping connector etc of suitable size fixed on surface of walls/roofs/ceiling and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated, unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old unserviceableitem complete and making good the disturbed surfaces to match with existing all as specified and directed. Note : -02 run of 4 sqmm single core copper conductor cable and one run of 4 sqmm single core copper conductor cable and 01 run of PVC casing and capping shall be measured as one unit. |
| 111 | Supply & fix in repair MCB SPN 32 Amps 10 KA, \"C\" series, 240 volts complete all as specified and directed. |
| 112 | Supply and fix in replacement of sheet metal enclosures with two pin and earth plug and socket complete with single pole MCB 20 Amps complete all as specified and directed. |
| 113 | Supply,install,testing and commisioning of split type air conditioner 2 TR capacity with cooling function of inverter technology with cordless remote control, single phase, 240 volts complete with all accessories such as indoor and outdoor units and refrigerant tubing of adequate length as required at site, indoor mounting plate, drain pipe of suitable size brought upto ground level from any height including making cable connection by providing three core 2.5 sqmm copper conductor cable PVC insulated, sheathed of adequate length as required at site including making round hole on existing any type of wall (core cutting if required ) for taking up refrigerant tubing, drain pipe and cables etc and making good the disturbed surface by matching with existing adjoining surfaces complete all as specified and directed. |
| 114 | Supply and fix voltage stablizer of 5 KVA capacity suitable to voltage 170 volt to 240 volt complete all as specified and directed . |
| 115 | M& L for Point wiring complete with 1100 volts grade FRLS insulated unsheathed cable of copper conductor cable multi stranded of size 1.5 Sqmm single coreincluding PVC rigid Casing Caping medium grade of suitable size (not lessthan 20mm dia) with all accessories such asbend reducers /MS hooks, MS junctionbox 1.2mm thick MS pressed sunken terminal boxes of suitable sizes for mounting of switches sockets, fan regulators etc covered with 3.15 mm thick bakelite laminated (Hylem/Anchor) top cover including continuous earth wire of size 1.5 Sqmm PVCstrandedcopper conductor unsheathed, insulated stranded (Green colour) connected to common earthpoint dolly ,complete all as specified and as directed by Engr-in-charge .for the following:- |
| 116 | One 3 pin socket outlet, 5 amps, independent , with cables 1.5 sq. mm size |
| 117 | Supply and Fixing Switch socket combination 2 in 1, 6A flush type |
| 118 | Supply and fixing wall mounted fan 5 star rated, 400 mm sweep , 220 volt, 50 Hz, Single phase, complete all as specified and as directed by Engr-in-charge. |
| 119 | Supply and fix LED luminaire 600mm x 600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver , holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. |
| 120 | Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as directed. |
| 121 | Taking down and refixing of split AC of 1.5 TRto 2 TR indoor unit including electrical connection and closing of refrigerant gas and deposit to MES store yard for re-fixing complete with top up of refrigerant as requiered pressure complete with servicing of indoor and out door unit all as directed by Engr-In-Charge. |
