Tender For Construction Of Ocr Of Sib At Daporijo Sh Type Ii Type Iii And Iv And Multistorey Rcc Building - Rcc Building Works And Services., Upper Subansiri-Arunachal Pradesh

TDR : 53090624

Tender Notice
BOQ

Expired

Upper Subansiri , Arunachal Pradesh

Tender Brief : Tender For Construction Of Ocr Of Sib At Daporijo Sh Type Ii Type Iii And Iv And Multistorey Rcc Building - Rcc Building Works And Services.

Document Fees
₹ 3000 /-

EMD
₹ 486429.0 /-

Tender Value
Refer document

Submission Date
29-12-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Type-II 4 units ( Double storey)
2	I. Earthwork
3	Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning.
4	II. CC Work
5	Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering ina) Foundations and plinth
6	Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :a) Foundations and plinth
7	Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.
8	III. RCC Work
9	Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcementin : b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
10	Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
11	Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
12	Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
13	Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement:1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
14	Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
15	Centring and shuttering including strutting, propping etc and removal of form work for :
16	a) Foundation, footings, bases of columns etc. and mass concrete.
17	c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
18	d) Lintels, beams, girders, bressumers and cantilevers etc.
19	e) Column, pillars, posts and struts etc.
20	Reinforcement of RCC work including bending, binding and placing in position complete.b) Tar/TMT Steel
21	IV. Brick Work
22	Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).
23	Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.
24	Extra for half brick masonry in superstructure above plinth level and up to floor two level.
25	Aluminium Works
26	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
27	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)
28	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.
29	Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.b) Ornamental grill.
30	Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.a) 300 x 16 mm
31	Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessaryscrews etc complete.
32	a) 300 x 10 mm
33	c) 150 x 10 mm
34	Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.a) 125 mm
35	VI. Flooring
36	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete.b) size of tiles 600x600mm
37	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete.b) size of tiles 600x600mm
38	White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.
39	VII. Roofing
40	Steelworkinbuiltuptubulartrussesincludingcutting,hoisting,fixingin position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).
41	Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer\"s specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm
42	Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer\"s specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m
43	False Ceiling
44	Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).
45	Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.a) Best local approved quality wood.
46	Extra for chamfered edges in beading
47	VII. Finishing
48	12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).
49	15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall
50	6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).
51	Applying one coat of cemenl primer of approved brand and manufacture on wall surface.
52	Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.
53	Distempering (lwo or more coats) with oil bound washable distemper of approved brandand manufacture and of required shade on new work over and including a priming coatwith distemper primer of approved brand and manufacture to give an even shade.
54	VIII. Miscelleneous
55	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
56	X. Water Supply
57	Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).a) 15 mm nominal bore
58	b) 20 mm nominal bore.Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).
59	a) 15 mm nominal bore
60	b) 20 mm nominal bore
61	d) 32 mm nominal bore
62	Providing and fixing brass bib cock of approved quality.a)15 mm nominal bore
63	Providing and fixing brass stop cock of approved quality.a) 15 mm nominal bore
64	XI. Sanitary Installations
65	Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.
66	a) Long Pan patten WC Pan
67	Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain inenamelledflushband,20mmoverflowpipewithspecialsandmosquitoproof coupling of approved municipal design complete including cutting and making good the walls and floors where required.
68	a) WC pan with white plastic seat and lid.
69	Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.
70	b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.
71	Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.
72	a) 250 x 130 x 30 mm
73	Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.
74	Providing and fixing kitchen sink including making all connection excluding cost of fittings.a) White glazed fire clay sink size 600x450x150 mm
75	Providing and fixing CP Brass Chain and rubber plug complete for sink or wash basins.
76	Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia
77	Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.
78	Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.
79	Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.
80	Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size
81	Providing and fixing toilet paper holder.a) CP Brass
82	Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.
83	a) 100 mm dia
84	c) 50 mm dia
85	Providing and fixing UPVC/PVC heel rest sanitary bend.
86	a) 100 mm dia
87	c )50 mm dia
88	Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
89	a) 100 x 100 x 100 mm
90	Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.
91	c) 100 mm inlet and 50 mm outlet
92	Cost for internal electrification
93	POINT WIRING
94	Supply, Installation, testing and commissioningConduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of -a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type ofPVC conduit as required.b) 1100V grade PVC insulated CuFR Wire.c) Insulated or base protective earthd) 1.6 mm thick Outlet boxes and junction box as per manufacturers standarde) Allwork & materials necessary for wiring a point circuit of anylengthfromtheFinal DistributionBoardto switch board, except where identified.f) Embedding/surface conduits and accessories in walls and floorsetc. duringconstruction and / or cutting chases(with chase cutting machine) and makinggood with finishing of wall after embedding of conduit on walls.g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required.f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.
95	Wiring for primary points from SB to first light pointwith 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box Average=5 mtr
96	Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr
97	Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr
98	Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr
99	Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Locationwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=4 mtr
100	Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Locationwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=4 mtr
101	Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch boardwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=0.5 mtr
102	Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch, fan regulator,modular plate, suitable GI box and 3\" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr
103	Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket,modular plate, suitable GI box.
104	Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduitconductor, already laid concealed HMS class PVC conduit as required. (only wiring)
105	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
106	2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire
107	Supplying and fixing of following sizes of HMS class PVC conduitalong with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
108	25 mm
109	32 mm
110	LOW VOLTAGE WIRING
111	LVWires
112	Supply, Installation, testing and commissioning Indoors PVC insulated LV Wires on walls, ceiling, cable trays complete with clamps Termination etc
113	CAT 6 cabledata including terminations in already laid conduits.
114	For Telophone including terminations in already laid conduits. 2 pair 0.5mm
115	RG -6cable for TV outletincluding terminationsin already laid conduit.
116	RG -11 cable for TV outletincluding terminationsin already laid conduit.
117	LVCables
118	Supply, Installation, testing and commissioning Indoors multipair 0.5mm dia copper PVC insulated and sheathed, armoured telephone cables on walls, ceiling, cable trays complete with clamps Termination, cable markers etc. from MDF to the various tag blocks as specified and shown on drawings.
119	10 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
120	20 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
121	50 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
122	100 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
123	Supplying and fixing of following sizes of HMS class PVC conduitalong with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
124	25 mm
125	32 mm
126	LT CABLING SYSTEM
127	POWER CABLES
128	Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLScables indoor or outdoor with Cu conductors asspecified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:-a) Cable clamps on walls, columns, beams, cable markers etc.Cable Dressing on Trays,Trenches & HDPE Pipesb) Earthing the glands armouring etc.c) Aluminium tags for all XLPE Al/ Cu cables to be provided.
129	4c x 1.5sq.mm Cu XLPE Cable
130	4c x 2.5sq.mm Cu XLPE Cable
131	4c x 4sq.mm Cu XLPE Cable
132	TERMINATIONS WITH SINGLE COMPRESSION GLANDS,LUGS & ACCESSORIES
133	4c x 1.5sq.mm Cu XLPE Cable
134	4c x 2.5sq.mm Cu XLPE Cable
135	4c x 4sq.mm Cu XLPE Cable
136	3c x 4sq.mm Cu XLPE Cable
137	4c x 6sq.mm Cu XLPE Cable
138	4c x 10sq.mm Cu XLPE Cable
139	Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLScables indoor or outdoor with AL conductors asspecified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:-a) Cable clamps on walls, columns, beams, cable markers etc.Cable Dressing on Trays,Trenches & HDPE Pipesb) Earthing the glands armouring etc.c) Aluminium tags for all XLPE Al/ Cu cables to be provided.
140	3.5C x 120sq.mm AL XLPE Cable
141	3.5C x 70sq.mm AL XLPE Cable
142	3.5C x 50sq.mm AL XLPE Cable
143	3.5C x 35sq.mm AL XLPE Cable
144	CABLE TRAY
145	Supply, Installation ofhot dip galvanisedcable trays with necessary painted M.S structural supports in horizontal or vertical formation & single / multitier formation, Quoted rates for installation shall include GI nut and bolt, bend, TEE joint, reducer, coupler and all necessary accessoriesGI channel supports @ 1000mm interval etc., to suit site conditions
146	300mm width X 50 mm depth X 2 mm thickness (perforated )
147	150mm width X 50 mm depth X 2 mm thickness( Perforated )
148	LIGHTING FIXTURES AND FANS
149	Supply, Installation, testing and commissioning of following light fixtures and fans as per drawings and specifications with all other accessories. The rate shall include all accessories required to complete the installation as required, Earthing of fittings & Connections from the ceiling rose or junction box of the fitting including Flexible Wires,hangers,chains Complete in all respect.
150	LED 18 W round shape Cielling Mounted
151	LED 30 W square shape Cielling Mounted 300 x 300mm
152	80W CiellingMounted Fan 1200mm Dia
153	Door bell
154	Electric 5.5 L Instant Water Geyser \| High Grade SS Tank
155	Exhaust Fan 6 inch Ventilation Fan Pure Copper Motor 150 mm
156	COMMON AREA/STAIRCASE/LOBBY ETC.
157	Primary Light points Lift lobbyin 25mm conduit Average-12mtr
158	Secondary Light pointsin 25mm conduitAverage-3 mtr
159	PANELS & DISTRIBUTION BOARDS
160	Supply, installation, testing and commissioning of cubicle type panels of 14 SWG CRCA sheet steel floor mounted totally enclosed with top and bottom cable entry and suitable for use on 433 V 3 phase 4 wire 50 c/s having 35 KA fault capacity complete and housed with Aluminium/copper bus bar equipments and their accessories including supply and fixing of base channels of 100x50x6mm as required and with following incoming and outgoing switchgear with protection, metering etc. complete as required and as per specification and schematic diagram.
161	6 WAY TPN-DB LDB
162	12 WAY SPNGR Floor
163	EARTHING SYSTEM
164	Chemical earthing 17,2mm dia 3 mtr long with 50kg BFC CompoundWith brick workchamber 300 x 300mm
165	25 x 6 mm G.I.
166	25 x 3 mm G.I.
167	8 SWG G.I earthwires
168	8 SWG Cu earthwires
169	Add Septic Tank(100 User)
170	Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning t
171	Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.
172	Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering ina) Foundations and plinth
173	Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
174	Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.
175	a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
176	Centring and shuttering including strutting, propping etc and removal of form work for :
177	a) Foundation, footings, bases of columns etc. and mass concrete.
178	c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
179	Reinforcement of RCC work including bending, binding and placing in position complete.
180	b) Tar/TMT Steel
181	Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).
182	40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 (1cement: 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) & top layer of 10 mm thick plaster of cement red oxide mix (using 3.5 kg of red oxide of iron per 50 kg of cement) 1 : 3 (1 cement red oxide mix : 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same proportion.
183	Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3coarse sand) finished with a floating coat of neat cement, including rounding of junctionswith floor.a) 18 mm thick
184	Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.
185	a) 100 mm dia
186	Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft andSW drain pipe 100 mmdia 1.80 m long complete,as per standard design.
187	Furniture
188	Type-III 4 units(Double storey)
189	I. Earthwork
190	Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning .
191	II. CC Work
192	Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering ina) Foundations and plinth
193	Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :
194	a) Foundations and plinth
195	Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.
196	III. RCC Work
197	Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcementin :
198	b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
199	Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
200	Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.
201	a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
202	Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.
203	b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
204	Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement:1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
205	Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
206	Centring and shuttering including strutting, propping etc and removal of form work for :
207	a) Foundation, footings, bases of columns etc. and mass concrete.
208	c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
209	d) Lintels, beams, girders, bressumers and cantilevers etc.
210	e) Column, pillars, posts and struts etc.
211	Reinforcement of RCC work including bending, binding and placing in position complete.
212	b) Tar/TMT Steel
213	IV. Brick Work
214	Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).
215	Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.
216	Extra for half brick masonry in superstructure above plinth level and up to floor two level.
217	Aluminium Works
218	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
219	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
220	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)
221	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.
222	Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.
223	b) Ornamental grill.
224	Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.
225	a) 300 x 16 mm
226	Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessaryscrews etc complete.
227	a) 300 x 10 mm
228	c) 150 x 10 mm
229	Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.
230	a) 125 mm
231	VI. Flooring
232	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete.b) size of tiles 600x600mm
233	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete.b) size of tiles 600x600mm
234	White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.
235	VII. Roofing
236	Steelworkinbuiltuptubulartrussesincludingcutting,hoisting,fixingin position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).
237	Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer\"s specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm
238	Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer\"s specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m
239	False Ceiling
240	Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).
241	Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.
242	a) Best local approved quality wood.
243	Extra for chamfered edges in beading
244	VII. Finishing
245	12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).
246	15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall
247	6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).
248	Applying one coat of cemenl primer of approved brand and manufacture on wall surface.
249	Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.
250	Distempering (lwo or more coats) with oil bound washable distemper of approved brandand manufacture and of required shade on new work over and including a priming coatwith distemper primer of approved brand and manufacture to give an even shade.
251	VIII. Miscelleneous
252	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
253	X. Water Supply
254	Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).
255	a) 15 mm nominal bore
256	b) 20 mm nominal bore
257	Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).
258	a) 15 mm nominal bore
259	b) 20 mm nominal bore
260	d) 32 mm nominal bore
261	Providing and fixing brass bib cock of approved quality.
262	a)15 mm nominal bore
263	Providing and fixing brass stop cock of approved quality.
264	a) 15 mm nominal bore
265	XI. Sanitary Installations
266	Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.
267	a) Long Pan patten WC Pan
268	Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain inenamelledflushband,20mmoverflowpipewithspecialsandmosquitoproof coupling of approved municipal design complete including cutting and making good the walls and floors where required.
269	a) WC pan with white plastic seat and lid.
270	Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.
271	b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.
272	Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.
273	a) 250 x 130 x 30 mm
274	Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.
275	Providing and fixing kitchen sink including making all connection excluding cost of fittings.a) White glazed fire clay sink size 600x450x150 mm
276	Providing and fixing CP Brass Chain and rubber plug complete for sink or wash basins.
277	Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia
278	Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.
279	Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.
280	Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.
281	Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size
282	Providing and fixing toilet paper holder.a) CP Brass
283	Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.
284	a) 100 mm dia
285	c) 50 mm dia
286	Providing and fixing UPVC/PVC heel rest sanitary bend.
287	a) 100 mm dia
288	c )50 mm dia
289	Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
290	a) 100 x 100 x 100 mm
291	Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.
292	c) 100 mm inlet and 50 mm outlet
293	Cost for internal electrification
294	POINT WIRING
295	Supply, Installation, testing and commissioningConduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of -a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type ofPVC conduit as required.b) 1100V grade PVC insulated CuFR Wire.c) Insulated or base protective earthd) 1.6 mm thick Outlet boxes and junction box as per manufacturers standarde) Allwork & materials necessary for wiring a point circuit of anylengthfromtheFinal DistributionBoardto switch board, except where identified.f) Embedding/surface conduits and accessories in walls and floorsetc. duringconstruction and / or cutting chases(with chase cutting machine) and makinggood with finishing of wall after embedding of conduit on walls.g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required.f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.
296	Wiring for primary points from SB to first light pointwith 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box Average=5 mtr
297	Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr
298	Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr
299	Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr
300	Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Locationwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=4 mtr
301	Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Locationwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=4 mtr
302	Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch boardwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=0.5 mtr
303	Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch, fan regulator,modular plate, suitable GI box and 3\" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr
304	Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket,modular plate, suitable GI box.
305	Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduitconductor, already laid concealed HMS class PVC conduit as required. (only wiring)
306	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
307	2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire
308	2 X 4.0 sq. mm + 1 X 2.5 sq. mm earth wire
309	2 x 6.0 sq.mm + 1 X 4 sq.mm earthg wire
310	Supplying and fixing of following sizes of HMS class PVC conduitalong with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
311	25 mm
312	32 mm
313	LOW VOLTAGE WIRING
314	LVWires
315	Supply, Installation, testing and commissioning Indoors PVC insulated LV Wires on walls, ceiling, cable trays complete with clamps Termination etc
316	CAT 6 cabledata including terminations in already laid conduits.
317	For Telophone including terminations in already laid conduits. 2 pair 0.5mm
318	RG -6cable for TV outletincluding terminationsin already laid conduit.
319	RG -11 cable for TV outletincluding terminationsin already laid conduit.
320	LVCables
321	Supply, Installation, testing and commissioning Indoors multipair 0.5mm dia copper PVC insulated and sheathed, armoured telephone cables on walls, ceiling, cable trays complete with clamps Termination, cable markers etc. from MDF to the various tag blocks as specified and shown on drawings.
322	10 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
323	20 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
324	50 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
325	100 pair 0.5 mm twisted pair non jelly filled armoured telephone cable
326	Supplying and fixing of following sizes of HMS class PVC conduitalong with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
327	25 mm
328	32 mm
329	TTB box with 20 pair krone
330	LT CABLING SYSTEM
331	POWER CABLES
332	Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLScables indoor or outdoor with Cu conductors asspecified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:-a) Cable clamps on walls, columns, beams, cable markers etc.Cable Dressing on Trays,Trenches & HDPE Pipesb) Earthing the glands armouring etc.c) Aluminium tags for all XLPE Al/ Cu cables to be provided.
333	4c x 1.5sq.mm Cu XLPE Cable
334	4c x 2.5sq.mm Cu XLPE Cable
335	4c x 4sq.mm Cu XLPE Cable
336	3c x 4sq.mm Cu XLPE Cable
337	TERMINATIONS WITH SINGLE COMPRESSION GLANDS,LUGS & ACCESSORIES
338	4c x 1.5sq.mm Cu XLPE Cable
339	4c x 2.5sq.mm Cu XLPE Cable
340	4c x 4sq.mm Cu XLPE Cable
341	3c x 4sq.mm Cu XLPE Cable
342	4c x 6sq.mm Cu XLPE Cable
343	4c x 10sq.mm Cu XLPE Cable
344	Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLScables indoor or outdoor with AL conductors asspecified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:-a) Cable clamps on walls, columns, beams, cable markers etc.Cable Dressing on Trays,Trenches & HDPE Pipesb) Earthing the glands armouring etc.c) Aluminium tags for all XLPE Al/ Cu cables to be provided.
345	3.5C x 120sq.mm AL XLPE Cable
346	3.5C x 70sq.mm AL XLPE Cable
347	3.5C x 50sq.mm AL XLPE Cable
348	3.5C x 35sq.mm AL XLPE Cable
349	CABLE TRAY
350	Supply, Installation ofhot dip galvanisedcable trays with necessary painted M.S structural supports in horizontal or vertical formation & single / multitier formation, Quoted rates for installation shall include GI nut and bolt, bend, TEE joint, reducer, coupler and all necessary accessoriesGI channel supports @ 1000mm interval etc., to suit site conditions
351	450mm width X 50 mm depth X 2.0 mm thickness ( Ladder )
352	300mm width X 50 mm depth X 2 mm thickness (perforated )
353	150mm width X 50 mm depth X 2 mm thickness( Perforated )
354	LIGHTING FIXTURES AND FANS
355	Supply, Installation, testing and commissioning of following light fixtures and fans as per drawings and specifications with all other accessories. The rate shall include all accessories required to complete the installation as required, Earthing of fittings & Connections from the ceiling rose or junction box of the fitting including Flexible Wires,hangers,chains Complete in all respect.
356	LED 18 W round shape Cielling Mounted
357	LED 30 W square shape Cielling Mounted 300 x 300mm
358	80W CiellingMounted Fan 1200mm Dia
359	Door bell
360	Electric 5.5 L Instant Water Geyser \| High Grade SS Tank
361	Exhaust Fan 6 inch Ventilation Fan Pure Copper Motor 150 mm
362	COMMON AREA/STAIRCASE/LOBBY ETC.
363	Primary Light points Lift lobbyin 25mm conduit Average-12mtr
364	Secondary Light pointsin 25mm conduitAverage-3 mtr
365	Add Septic Tank(100 User)
366	Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning t
367	Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.
368	Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering ina) Foundations and plinth
369	Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
370	Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.
371	a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
372	Centring and shuttering including strutting, propping etc and removal of form work for :
373	a) Foundation, footings, bases of columns etc. and mass concrete.
374	c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
375	Reinforcement of RCC work including bending, binding and placing in position complete.
376	b) Tar/TMT Steel
377	Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).
378	40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 (1cement: 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) & top layer of 10 mm thick plaster of cement red oxide mix (using 3.5 kg of red oxide of iron per 50 kg of cement) 1 : 3 (1 cement red oxide mix : 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same proportion.
379	Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3coarse sand) finished with a floating coat of neat cement, including rounding of junctionswith floor.a) 18 mm thick
380	Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.
381	a) 100 mm dia
382	Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft andSW drain pipe 100 mmdia 1.80 m long complete,as per standard design.
383	Furniture
384	Type-IV (Single storey)
385	I. Earthwork
386	Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning ....
387	II. CC Work
388	Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering ina) Foundations and plinth
389	Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :
390	a) Foundations and plinth
391	Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.
392	III. RCC Work
393	Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcementin :
394	b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
395	Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
396	Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.
397	a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
398	Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.
399	b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
400	Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement:1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
401	Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).
402	Centring and shuttering including strutting, propping etc and removal of form work for :
403	a) Foundation, footings, bases of columns etc. and mass concrete.
404	c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).
405	d) Lintels, beams, girders, bressumers and cantilevers etc.
406	e) Column, pillars, posts and struts etc.
407	Reinforcement of RCC work including bending, binding and placing in position complete.
408	b) Tar/TMT Steel
409	IV. Brick Work
410	Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).
411	Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.
412	Extra for half brick masonry in superstructure above plinth level and up to floor two level.
413	Aluminium Works
414	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)
415	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
416	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)
417	Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.
418	Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.
419	b) Ornamental grill.
420	Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.
421	a) 300 x 16 mm
422	Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessaryscrews etc complete.
423	a) 300 x 10 mm
424	c) 150 x 10 mm
425	Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.
426	a) 125 mm
427	VI. Flooring
428	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete.b) size of tiles 600x600mm
429	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete.b) size of tiles 600x600mm
430	White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.
431	VII. Roofing
432	Steelworkinbuiltuptubulartrussesincludingcutting,hoisting,fixingin position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).
433	Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer\"s specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm
434	Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer\"s specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m
435	False Ceiling
436	Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).
437	Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.
438	a) Best local approved quality wood.
439	Extra for chamfered edges in beading
440	VII. Finishing
441	12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).
442	15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall
443	6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).
444	Applying one coat of cemenl primer of approved brand and manufacture on wall surface.
445	Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.
446	Distempering (lwo or more coats) with oil bound washable distemper of approved brandand manufacture and of required shade on new work over and including a priming coatwith distemper primer of approved brand and manufacture to give an even shade.
447	X. Water Supply
448	Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).
449	a) 15 mm nominal bore
450	b) 20 mm nominal bore
451	Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).
452	a) 15 mm nominal bore
453	b) 20 mm nominal bore
454	d) 32 mm nominal bore
455	Providing and fixing brass bib cock of approved quality.
456	a)15 mm nominal bore
457	Providing and fixing brass stop cock of approved quality.
458	a) 15 mm nominal bore
459	XI. Sanitary Installations
460	Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.
461	a) Long Pan patten WC Pan
462	Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain inenamelledflushband,20mmoverflowpipewithspecialsandmosquitoproof coupling of approved municipal design complete including cutting and making good the walls and floors where required.
463	a) WC pan with white plastic seat and lid.
464	Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.
465	b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.
466	Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.
467	a) 250 x 130 x 30 mm
468	Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.
469	Providing and fixing kitchen sink including making all connection excluding cost of fittings.a) White glazed fire clay sink size 600x450x150 mm
470	Providing and fixing CP Brass Chain and rubber plug complete for sink or wash basins.
471	Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia
472	Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.
473	Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.
474	Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.
475	Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size
476	Providing and fixing toilet paper holder.a) CP Brass
477	Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.
478	a) 100 mm dia
479	c) 50 mm dia
480	Providing and fixing UPVC/PVC heel rest sanitary bend.
481	a) 100 mm dia
482	c )50 mm dia
483	Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
484	a) 100 x 100 x 100 mm
485	Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.
486	c) 100 mm inlet and 50 mm outlet
487	Cost for internal electrification
488	POINT WIRING
489	Supply, Installation, testing and commissioningConduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of -a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type ofPVC conduit as required.b) 1100V grade PVC insulated CuFR Wire.c) Insulated or base protective earthd) 1.6 mm thick Outlet boxes and junction box as per manufacturers standarde) Allwork & materials necessary for wiring a point circuit of anylengthfromtheFinal DistributionBoardto switch board, except where identified.f) Embedding/surface conduits and accessories in walls and floorsetc. duringconstruction and / or cutting chases(with chase cutting machine) and makinggood with finishing of wall after embedding of conduit on walls.g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required.f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.
490	Wiring for primary points from SB to first light pointwith 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box Average=5 mtr
491	Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr
492	Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr
493	Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr
494	Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Locationwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=4 mtr
495	Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Locationwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=4 mtr
496	Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch boardwith 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch,socket, modular plate, suitable GI box.Average=0.5 mtr
497	Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduitwith modular switch, fan regulator,modular plate, suitable GI box and 3\" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr
498	Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket,modular plate, suitable GI box.
499	Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduitconductor, already laid concealed HMS class PVC conduit as required. (only wiring)
500	2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Arunachal Pradesh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Ocr Of Sib At Daporijo Sh Type Ii Type Iii And Iv And Multistorey Rcc Building - Rcc Building Works And Services., Upper Subansiri-Arunachal Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Ocr Of Sib At Daporijo Sh Type Ii Type Iii And Iv And Multistorey Rcc Building - Rcc Building Works And Services., Upper Subansiri-Arunachal Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us