Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Notes:-(i) 100 percent/variation of items ofnonperishable items of the work as per siterequirement of Engineer-in-Charge shall be deposited by the L1 bidder within 30 days after placing of work order.(ii) The critical path network shall be submitted by L1 bidder immediately after the acceptance of tender and approved by GE.(iii) The bidders must ensure to visit the site, check relevant documents and makes of materials required to be incorporated under the subject from concern Engineer-in-Charge.(iv) The unserviceable material obtained under the schedule of credit shall be handed over to the contractor by the Engineer-in-Charge on a proper gate pass.(v) In case of non-availability of any make mentioned under list of Makes, in such case the L1 Bidder shall obtain non-availability / non-manufacturing certificate from the concern OEM / authorised dealers and submitted to Accepting Officer, the L1 bidder may be incorporated makes as approved by HQ CE SWC Jaipur in the works after prior approval of Accepting Officer.(vi) L1 Bidder shall produce E-way bill alongwith test certificate from OEM / manufacturer for costly items / major items of amount above Rs 50,000/- along with RAR’s and Final Bill.(vii) L1 Bidder shall be maintained an album containing Photos of all the material brought at site and each stage wise work progress and kept at site. Same shall be deposited in Engineer-in-Charge office after completion of work.(viii) The cost of all the above provisions shall be deemed to be included in the quoted rate of bidder, nothing extra shall be paid to the bidder. |
| 2 | Demolition of plain cement concrete in ground floor and pavings not exc 15 cm thick (below or above ground level) of any description complete all as specified and directed by Engineer-in-charge. |
| 3 | Demolition of brick work, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-charge. |
| 4 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge. |
| 5 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge. |
| 6 | Dismantling bricks (laid flat or on edge) or brick tiles on roof terrace, in floors, channels, kerbs, aprons etc laid dry or laid dry and pointed and removing from site complete all as specified & directed by Engineer-in-charge. |
| 7 | Taking down old unserviceable cooler stand of any size & any type fixed on external face of walls at cill level of windows at ground floor and first floor of building including cutting holes and making good the disturbed portion with cement mortar or PCC after refixing new cooler stand complete all as specified and directed by Engineer-in-charge. |
| 8 | Taking down steel window / ventilator of any description and of any type with or without guard bars and making good the disturbed portion complete all as specified and directed by Engineer-in-charge. |
| 9 | Dismantling of cast iron drain pipe of 100mm bore, jointed in CM and taking out from trenches complete all as specified and as directed by Engineer-in-charge.Note :- Excavation & earthwork shall be measured and paid separately |
| 10 | Dismantling of cast iron drain pipe of 75mm bore, jointed in CM and taking out from trenches complete all as specified and as directed by Engineer-in-charge.Note :- Excavation & earthwork shall be measured and paid separately |
| 11 | Demolition and breaking up 150 mm bore drain pipes (salt glazed stone ware, AC or reinforced concrete) including concrete bed and haunching and removing rubbish to a distance not exc 50m complete all as specified and as directed by Engineer-in-charge. |
| 12 | Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge. |
| 13 | Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge. |
| 14 | Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge. |
| 15 | Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge. |
| 16 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil & getting out complete all as specified and directed by Engineer-in-Charge. |
| 17 | Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge. |
| 18 | Removal of excavated soil/ material to a distance exc 250 metre and not exc 500 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and directed by Engineer-in-charge. |
| 19 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep in soft/ loose soil and getting out complete all as specified and directed by Engineer-in-Charge. |
| 20 | Spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed by Engineer-in-Charge |
| 21 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified and directed by Engineer-in-charge. |
| 22 | Water proofing treatment to sunken slab and adjjoining vertical surfaces as specified under :-(a) Demolition of cement concrete in sunken portion.(b) Preparation sunken surfaces by cleaning of and removal of loose concrete(c) Filling cracks with polymer modified mortar using Dr. Fixit Pidicrete URP or equivalent in Forsoc/Berger and other approved make(d) Applying 2 coats of Dr. Fixit Bath seal WPC in suken areas and laying a protective plaster in 10mm thickness in cement mortar (1:3) admixed with Dr. Fixit Pidicrete LW + @ 220ML per bag of cement(e) Applying mix ofofDR FIXIT PIDICRETE URP in the ratio 1:1:5 on floor and vertical surface of sunken portion as per manufacturers instructions complete(f) Filling with P:C:C 1:5:10 Type-E2using 40 mm graded brick aggregate complete all as specified and directed by Engineer-in-charge(f) 12mm thick rendering in cement mortar (1:4) mixed with water proofing compound (ISI marked) on fair faces of brick masonry or concrete surfaces as in sunken portion, with Neeru finish complete.Note: The plan area of floor shall be considered for payment. |
| 23 | Supply only integral water proofing compound (ISI marked) complete all as specified and directed by Engineer-in-charge. MAKE Dr fixit/STP FOSROC/BASF or equivalent technocommercial make as specified in Appendix \"A\". |
| 24 | M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation, filling & mass concrete complete all as specified and directed by Engineer-in-charge . |
| 25 | M&L for cement concrete (1:2:4) type B1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified and directed by Engineer-in-charge.Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately. |
| 26 | M&L for precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of drains, manholes, septic tanks, soakage wells etc. including placing in position and set in CM (1:6) complete all as specified & as directed by Engineer-in-charge.Note: - Reinforcement shall be measured and paid for separately. |
| 27 | M&L for reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) for slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and other similar works complete all as specified and directed and directed by Engineer-in-Charge. |
| 28 | M&L for cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, coping, parapets and railing upto 60cm height, copings bed block, roof kerbs or mud stops, kerb stone, kneelers, apex stones, bed plates, surface channels and drains, benching, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge. |
| 29 | M&L for Brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge. |
| 30 | M&L for Stone slab 25 mm to 35 mm thick dressed true and square, in one length not less than 60cm and n. exc 120cm in copings, window cills, chajjas, sunshades, etc., punched dressed on exposed faces and self faced on the embedded unexposed beds and joints; exposed edges rounded or chamfered as directed, set, jointed and pointed in cement mortar complete all as specified and directed by Engineer-in-charge. |
| 31 | M&L for use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick (horizontal or sloping), rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge. |
| 32 | S&F Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed by Engineer-in-charge. |
| 33 | S&F Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 complete all as specified and directed by Engineer-in-charge. |
| 34 | S&F as in repairs stainless steel drapery rod of 25 mm inner dia (in lengths as directed) with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed. |
| 35 | M&L for Factory made Single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 125x65mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). including dismantling existing wooden/iron/stone chowkhats complete and making good existing disturbed surface with cement and sand mortar 1:3 complete all as specified. |
| 36 | M&L for Factory made Single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 100x65mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). including dismantling existing wooden/iron/stone chowkhats complete and making good existing disturbed surface with cement and sand mortar 1:3 complete all as specified. |
| 37 | M&L for Factory made Single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45x85mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). including dismantling existing wooden/iron/stone chowkhats complete and making good existing disturbed surface with cement and sand mortar 1:3 complete all as specified. |
| 38 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be lamintated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel piano hinges of required size with necessary full body threaded star headed counter sunk S.S screws and including necessary ss Paino hinge and magnetic catcher and ss handle 150mm for each shutter all as per direction of Engineer-In-Charge. |
| 39 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 18-19mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be lamintated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel piano hinges of required size with necessary full body threaded star headed counter sunk S.S screws and including necessary ss Paino hinge and magnetic catcher and ss handle 150mm for each shutter all as per direction of Engineer-In-Charge. |
| 40 | S&F new 30 mm thick factory made flush shutters, solid core construction, withblock board core and plywood face panels, commercial type on both side incl both side completecomplete all as specified and directed by Engineer-in-charge including supply and fixing of following items :-(a)Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf(b)Stainless steel (304 Grade) finished square tower bolt 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm(c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf.(d)Stainless steel (304 Grade) finished sliding bolt 300 mm-1 No per leaf, 16 mm dia(e)Stainless steel (304 Grade) Finished Floor door stopper-1 140mm Nos per leaf.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 41 | S&F new 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat incl Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 (01 No in each shutter), strainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple ( for 01 Nos shutter), complete all as specified and directed by Engineer-in-charge including supply and fixing of following items :-(a)Stainless steel (304 Grade) finished retractable butt Hinges 100 mm, 4 Nos per leaf(b)Stainless steel (304 Grade) finished square tower bolt 200 mm long-2 Nos per leaf as per table 01 No. dia of bolt 12 mm(c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf.(d)Stainless steel (304 Grade) finished sliding bolt 300 mm-1 No per leaf, 16 mm dia(e)Stainless steel (304 Grade) Finished Floor door stopper-1 140mm Nos per leaf.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 42 | S&F door seal (brush type) of length exc 800mm and n exc 1000mm, width not less than 38mm fixed with screws complete all as specified and directed by Engineer-in-charge. |
| 43 | S&F mild steel cupboard shutter with frame, Godrej Pattern, made out of 0.71mm thick (22 guage) mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12mm dia bolt 150 mm long grouted in brick wall/concrete including making good the disturbed surfaces as original complete all as specified and as directed.Note : - The measurement for payment purpose shall be taken of flat area of front elevation and not girthwise. No other allowance for sides, folded portion, etc shall be admissible. The quoted rate shall be deemed to include this provision. Make:Godrej Interio/Neelkamal/Durian or equivalent technocommercial make as specified in Appendix \"A\". |
| 44 | S&F mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-charge. |
| 45 | S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge. |
| 46 | S&F as in repair stainless steel peg set with 06 No of hooks mounted on SS plate 4mm thick fixed with Cp brass screws complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F anodised aluminium frames powder coated (thickness of powder coating shall not less than 50 micron) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc and as per the speicification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fastners including making arrangement to fix guard bars and PVC sleeves for guard bars. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete all as specified and directed by Engineer-in-Charge. Make :- FENESTA/NALCO/AISor equivalent technocommercial make as specified in Appendix \"A\". |
| 48 | S&F anodised aluminium window / ventilators shutters powder coated (thickness of powder coating shall not less than 50 micron) side hung type, without sash bars having aluminium sections weighting 0.55 Kg/RM including necessary jointing cleats, glazing clips, anodised aluminium snap beading, screws, rubber neoprene packing including anodised aluminium fitting such as peg stay 150mm long (1 No), hinges type B21 100mm size (2 Nos), suitable handle (1No) complete all as specified and directed by Engineer-in-Charge. Make :- FENESTA/NALCO/AISor equivalent technocommercial make as specified in Appendix \"A\". |
| 49 | S&F magnetic catcher fixed with nut, screw and washer complete all as specified & directed by Engineer-in- charge. |
| 50 | M&L for machine cut single piece Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer-in-charge. |
| 51 | M&L for machine cut Kota stone slab 20 to 25mm thick (minimum size 550mm x 100mm or size as directed), on vertical surfaces such as dado, skirting, raiser of steps etc. laid over & including rendering 10mm thick in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, grinding, rubbing and mirror polishing complete all as specified and directed by Engineer-in-charge. |
| 52 | Demolition of mud phuska in roof any thickness including plastering & leeping (whether full thickness removed or only part thereof) complete all as specified and directed by Engineer-in-charge. |
| 53 | M&L for Roof treatment in as specified below and as directed(a) Cleaning the roof surfaces thoroughly using wire brushes to remove sharp projections, cleaning joints, washing, drying and removing all dirt/dust to receive concrete padding/ plaster etc complete.(b) Applying one coat of elastomeric PU based liquid membrane diluted with potable water in the ratio of 1:1 and apply @ 0.40 Kg/Sqm. (c) Laying polyster reinforced fiber net / 150 sqm Geotextile mesh, upto 300mm on walls.(d) Applying two coats of undilited PU based liquid membrane having Elongation more than 400%, Tensile strength more than 2N/mm2 and alkali & antifungal resistant maintaining thickness of 1.5mm with paint brush/ roller upto 300mm on walls.(e) The complete treatment to be carried out by authorised applicator of waterproofing manufacturer. Note : (i) The treatment shall be carried out as per manufacturer instructions and as directed by Engineer-in-Charge.(ii) The plan area of floor shall be considered for payment. Make :M/s Pidilite India/Fosroc/Berger |
| 54 | M&L for 18-20mm thick Granite slab of approved shade and colour as in cooking platforms, steps, jambs, pillars, window cills and the like etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 15mm thick screed bed (bedding layer) in CM (1:6) complete all as specified and directed by Engineer-in-charge.Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision. |
| 55 | M&L for 50 mm thick PCC (1:3:6) type C1 using 20 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed.Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item |
| 56 | M&L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in sub base, finished fair and even complete all as specified and directed. |
| 57 | M&L for 40mm thick PCC (1:2:4) type B1 using 20mm graded crushed stone aggregate as in roof finished even and smooth without using extra cement complete all as specified and as directed. |
| 58 | M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\". |
| 59 | M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge.Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\". |
| 60 | M&L for glazed ceramic tiles (coloured) 300mm x 450mm x 7-8mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.Make :- Johnson/Kajaria/Somany or equivalent technocommercial make as specified in Appendix \"A\". |
| 61 | M&L for heat resistant terrace tiles (300mm x 300mm x 10-12mm) with SRI (Solar reflactive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on water proof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with cmentious grout of approved make including rubbing and polishing of the surface upto 3 cuts complete including providing skirting upto 150mm height along the parapet walls in the same manner complete all as specified and directed by Engineer-in-charge. |
| 62 | S&F factory casted 60mm thick machine pressed precast concrete coloured designer polished (rubber moulded coloured interlocking tiles with glossy finish) interlocking paver blocks of grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment with coloured top casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified and directed by Engineer-in-Charge.Note :- Shape & Colour of paver blocks shall be as approved by GE. |
| 63 | M&L for 10mm thick rendering in cement mortar (1:4) on brick walls/concrete surfaces mixed with water proofing compound as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.Note : - Supply only water proofing compound shall be measured and paid for separately under respective item of BOQ. |
| 64 | M&L for 15mm thick rendering in cement mortar (1:4) on brick walls/concrete surfaces mixed with water proofing compound 3% by weight of cement finished as per manufacturer’s instructions including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.Note : - Water proofing compound shall be included in this items. Nothing extra shall be paid on this account. |
| 65 | M&L for 15mm thick rendering in cement mortar (1:4) on fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge. |
| 66 | M&L for 15mm thick rendering in cement mortar (1:6) on fair faced brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed. |
| 67 | M&L for 10mm thick rendering in cement mortar (1:3) on brick or concrete surface of ceiling, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge. |
| 68 | M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. |
| 69 | M&L for preparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade/tint over a coat of cement base primer and filling cement based putty in cracks complete all as specified and directed by Engineer-in-charge. |
| 70 | M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, filling cracks with wall care putty etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 71 | M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying two coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 72 | Material & Labour of newly plastered for applying Twocoats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali &fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exteriorprimer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-Charge.Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or Techno commercial as mentioned in Appx \"A\". |
| 73 | M & L for preparation of newly plastered surfaces of wall & applying two coats of Interior emulsion paint by Roller or Air Spray over 1 mm thick wall care putty (Multipurpose mixer shall be used for uniform and proper mixing of putty)complete all as specified and as directed by Engineer-in- charge.Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or Techno commercial as mentioned in Appx \"A\". |
| 74 | M&L Complete removal of existing treatment and preparation of old decorated (platered or unplastered) of wall by Vaccume based sanding machine, removal of nails etc including filling of cracks and applying two coats of Interioremulsion paintby Roller or Air Spray incl over a layer of 1 mm or as required ( Multipurpose mixer shall be used for uniform and proper mixing of putty) of wall care putty, on plastered surfaces,prepara-tory to distempering complete all as specified & directed by Engineer -in-charge.Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or Techno commercial as mentioned in Appx \"A\". |
| 75 | Material and labour for complete removal of existing treatment from old decorated plastered surfaces of wall by Vaccume based sanding machine, removal of nails etc & filling cracks/hole with putty, and finally washing with wateringand applying two coats of exterior emulsion acyrlic weatherproof antifungal paint over a coat of exterior grade primer byAuto Roller over 1 mm thick wall care putty, including necessary scffoldings complte all as specified and as directed.Make : Tractor Emulsion (Asian Paint), Easy Clean (Berger Paint), Promise Inerior (Dulux Akzonobel) or Techno commercial as mentioned in Appx \"A\". |
| 76 | M&L for preparation of new plastered surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed by Engineer-in-Charge. |
| 77 | M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. Make : NEROLAC (HI-GLOSS), ASIAN PAINTS (APCOLITE),BERGER PAINTS (LUXOL) or Techno commercial as mentioned in Appx \"A\". |
| 78 | M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge. Make : NEROLAC (HI-GLOSS), ASIAN PAINTS (APCOLITE),BERGER PAINTS (LUXOL) or Techno commercial as mentioned in Appx \"A\". |
| 79 | M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-charge. Make : NEROLAC (HI-GLOSS), ASIAN PAINTS (APCOLITE),BERGER PAINTS (LUXOL) or Techno commercial as mentioned in Appx \"A\". |
| 80 | S&F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed. |
| 81 | S&F 5mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge. |
| 82 | Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supplying and laying of 20mm Outer dia CPVC pipes SDR 13.5 & Plain / brass CPVC SDR 11 fittings and fixed complete to walls and ceilings or laid in floors, trenches complete all as specified and directed by Engineer-in-charge. Make : Finolex/Supreme/Princeor equivalent technocommercial make as specified in Appendix \"A\". |
| 84 | Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supplying and laying of 25mm outer dia CPVC pipes SDR 13.5 & Plain / brass CPVC SDR 11 fittings and fixed complete to walls and ceilings or laid in floors, trenches complete all as specified and directed by Engineer-in-charge.Make : Finolex/Supreme/Princeor equivalent technocommercial make as specified in Appendix \"A\". |
| 86 | S&F CPVC brass male brass threaded adaptor special fitting (MTA/MBTA) for connecting of CPVC tubing outer dia 20/25mm complete all as specified and directed by Engineer-in-c/harge. |
| 87 | S&F 20mm outer dia CPVC brass elbow fittings complete all as specified and directed by Engineer-in-charge Make : Finolex/Supreme/Princeor equivalent technocommercial make as specified in Appendix \"A\". |
| 88 | S&F in repair, 15 mm bore shower rose and shower arm , 125 mm size or size as per Cat part mentioned below in makes, brass chromium plated withsweivel joint and 15mm bore stop valve (concealed), fancy type, chromium plated,screwed down, high pressure and screwed both ends for iron pipe or for unions complete all as directed. |
| 89 | S&F as in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge. |
| 90 | S&F as in repair brass chromium plated tubular towel rail 20mm dia; \"D\" type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. |
| 91 | S&F as in repair floor drainer with Collar and Cockroach Trap grating jali with/ without waste hole (minimum weight 25 grams) complete all as specified and directed by Engineer-in-Charge. |
| 92 | S&F as in repairrotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litres including 20mm bore PTMT float valve, 20mm bore cpvc ball valve and flynut screwed for 20 mm dia GI pipe, 25mm bore GI washout pipe 15 cm long fitted with check nut, 20mm bore over flow pipe 1.50 metre long fitted with brass anti-mosquito nest coupling at the end of over flow pipe & 15mm bore GI air vent pipe 1.30 metre long fitted with tee at the end of air vent pipe (All GI pipes shall be medium grade) complete all as specified and directed by Engineer-in-Charge.Make :-Sintex/Rotex/Polycon or equivalent technocommercial make as specified in Appendix \"A\". |
| 93 | S&F as in repair 15 mm bore bib tap (minimum weight 575 gms) cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge.Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 94 | S&F as in repair 15mm bore Pillar tap (minimum weight 960 gms) cast copper alloy with capstan head, screwed down, high pressure , chromium plated, with or without lettered hot or cold woth long screwed shanks and flynut complete all as specified and directed by Engineer-in-charge.Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 95 | S&F as in repair 15mm dia stop cock (minimum weight 575 gms) cast copper alloy, fancy type with, chromium plated long shank and cup (concealed type) with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge. Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 96 | S&F as in repair 15mm dia stop cock (minimum weight 575 gms) cast copper alloy, angular type with, chromium plated long shank and cup with crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge. Make : Jaquar/Hindware/Parrywareor equivalent technocommercial make as specified in Appendix \"A\". |
| 97 | S&F as in repair chromium plated Soap dish holder including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge. |
| 98 | Supply and fixing in repair wash basinSize 400x400 mm with angle back ,including angle iron brackets and stainless steel coupling and waste pipecomplete all as specified and directed by Engineer-in-Charge.colour shall be decided by Engr-in-Charge. MAKE HINDWARE QUED/JAQUAR/PARRYWARE or Techno commercial as mentioned in Appx \"A\". |
| 99 | S&F in repair Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. with & including WC seat cover closed pattern with flat bottom and cover, health faucet ABS CP, one piece /single body pvc alongwith blow moulded concealed cistern, pneumatic type capacity 10 litreincluding chrome finish dual flush control plate, flushing pipe and fixing bracket complete assembled with necessary fittings and fixtuers including necessary brick work and plastering for fixing the concealed cistern complete all as specified & as directed by Engineer-in-charge. MAKE HINDWARE QUED/JAQUAR/PARRYWARE or Techno commercial as mentioned in Appx \"A\". |
| 100 | S&F as in repair PVC cornercabinetmirror of size 300x450mmcomplete all as specified & directed by Engineer-in-Charge. |
| 101 | S&F as in repair sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, overall size 915mm x 460 mm / (36\" x 18\") bowl size 410mm x 355mm / (16\" x 14\") and depth 175mm / (7\") including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated 32mm bore with long screwed shanks and fly nuts including making holes in brick walls for brackets and fixed in CM (1:3) or PCC 1:2:4 type B0 complete all as specified and directed by Engineer-in-charge.Make :- Nirali model Elegance (Glossy) / Prayag model No 1128-D Gold Series (Gloss) /NEELKANTH or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after.Note :- Size of sink for different mafufacturer may slightly varried from size mentioned in description of item. Contractor has to provide sink as per cat No mentioned against make of sink. where cat No is not mentioned against any make, in that case sink of size mentioned in description has to provide, if exact size of sink is not available, then next higher size sink has to be provided. Nothing extra shall be paid on this account. |
| 102 | S&F as in repair stainless steel plate rack of size 900mm x 900mm x 250mm made out of 1.00mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge.Make: NEELKANTH / Prayag / NEERALI or equivalent in makes mentioned in Appendix \"A\" here-in-after. |
| 103 | S&F as in repair Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms/ 40mm-270 gms) completeall as specified & directed by Engineer-in-charge. |
| 104 | S&F as in repair 75mm dia PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge. |
| 105 | S&F DWCPE (SN8) pipe 160 (outer) /136 (inner) mm dia as per IS-16098 (Part-II) laid in trenches or in floor on moorum bed to required shape including all necessary accessories / fitting / jointing / rings, joiting and testing over &including 100mm PCC 1:4:8 type D2 using 40mm graded coarse aggregate complete all as specified & directed by Engineer-in-charge. Make: To be approved by GE |
| 106 | Supply & fixing 110mm bore uPVC pipes grade ‘B’ single socketed in any length with rubber ring joints, fixed along walls with incl all the necessary fitting like bends/trap/tee and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Make of Pipe: FINOLEX/PRICE/SUPREME or equivalent in makes mentioned in Appendix \"A\" here-in-after.Note:-Bracket, clamp, nut bolt, fastener, slotted channel etc. shall be made of deep drawn low carbon steelmaterial with hot dip zinc aluminium flake coated and fixed all as shown on BTD-916 drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account.Note:(i) the testing for leakage of pipe shall be done before connecting the pipes(ii) All pipes shall be minimum 4\" away from walls fixed with GI bracket(iii)The gully trap shall be minimum 90 cm away from wall.(iv)Separate pipes for each floor should be provided.(v) Sewage and drain system shall be seperate.Make of Clamp: ISI Marked as approved by GE. |
| 107 | Supply & fixing 110mm bore uPVC pipes grade ‘B’ single socketed in any length with rubber ring joints, fixed along walls with incl all the necessary fitting like bends/trap/tee and complete all as specified and as directed by Engineer-in- charge. |
| 108 | Supply & fixing 75mm bore uPVC pipes grade ‘B’ single socketed in any length with rubber ring joints, fixed along walls with incl all the necessary fitting like bends/trap/tee and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Make of Pipe: FINOLEX/PRICE/SUPREME or equivalent in makes mentioned in Appendix \"A\" here-in-afterNote:-Bracket, clamp, nut bolt, fastener, slotted channel etc. shall be made of deep drawn low carbon steelmaterial with hot dip zinc aluminium flake coated and fixed all as shown on BTD-916 drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account.Note:(i) the testing for leakage of pipe shall be done before connecting the pipes(ii) All pipes shall be minimum 4\" away from walls fixed with GI bracket(iii)The gully trap shall be minimum 90 cm away from wall.(iv)Separate pipes for each floor should be provided.(v) Sewage and drain system shall be seperate.Make of clamp:ISI Marked as approved by GE. |
| 109 | S&F 75mm bore PVC (SWR) pipes single socketed in any length with solvent joints laid In trenches or in floors complete all as specified and directed by Engineer-in-charge. Make of Pipe: FINOLEX/PRICE/SUPREME or equivalent in makes mentioned in Appendix \"A\" here-in-after |
| 110 | S&F 110 mm bore uPVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge. |
| 111 | S&F 75 mm bore uPVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge. |
| 112 | S&F 75mm bore PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge |
| 113 | S&F 110mm bore PVC (SWR) reducers 110mm to 75mm complete all as specified and directed by Engineer-in-Charge |
| 114 | S&F 110mm bore uPVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge\" |
| 115 | S&F 75mm bore uPVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge\" |
| 116 | Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge. |
| 117 | M&L for Modular point wiring complete with 2.5 Sqmm (nominal cross section area) FRLSH PVC insulated multistranded unsheathed copper conductor cable drawn in and including concealed PVC rigid conduit medium grade 20mm dia, pipe hooks, elbows, junction covers and junction boxes including cutting chases in walls for conduits and for sunken pressed steel terminal boxes and making good the disturbed surfaces of wall with all jointing accessories including provision of pressed steel sunken terminal boxes made of 1.2mm thick pressed steel sheet, 60mm deep of suitable length and painted with red oxide primer for mounting modular switches, sockets, fan regulator including suitable size modular plates fixed flush with wall including 2.5 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point, fan point, bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.Note : The quoted rate shall be deemed to included with modular cover plates with frame of any colour and metal flush boxes of suitable size as directed by Engr-in-Charge. Make of Cable: Havells/Finolex/L&T or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after.Make of Conduit :Supreme/AKG/Finolex or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 118 | All as per serial item No. 116 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches. |
| 119 | All as per serial item No. 116 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board. |
| 120 | All as per Srl item No. 116 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 6 pin, 5/15 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly. |
| 121 | S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 122 | S&F Modular Switch socket Combination 5A, 3 pin, 3 modular, 230 Volts grade complete all as specified and directed by Engineer-in-charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 123 | S&F Modular Switch socket Combination 06/16A, 6 pin, 3 modular, 230 Volts grade complete all as specified and directed by Engineer-in-charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 124 | S&F Modular electronic fan regulator suitable for ceiling fan 2 Module, 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 125 | S&F as in repair sheet metal plug & socket DB, SP, with a two pin and earth plug with socket,230 Volts with & including one MCB SP ‘C’ Curve 10 kA, 20 Amps complete all as specified and directed by Engineer-in-charge. |
| 126 | S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 127 | S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 128 | S&F electric bell (ding - dong), AC, 230 Volts, Single pole & connecting up complete all as specified and directed by Engineer-in-charge. Make:Havells (Crabtree)/Legrand/Panasonic (Anchor) or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 129 | S&F Energy efficient decorative ultra slim, prewired, lumiline 18 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make:Havells /Phillips/Wipro or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 130 | S&F Energy efficient decorative ultra slim prewired 9 / 10watt(600mm length) LED light fitting (Mirror light) (Day cool light), surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser & integrated electronic driver and all accessories fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make:Havells /Phillips/Wipro or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 131 | S&F as in repair LED battery backup inverter bulb of lamp wattage 12 watt, battery not less than 2200mAh or not less than 4 hrs, efficacy not less than 120 Lumen/watt complete all as specified and as directed by Engineer-in-charge. Make:Havells /Phillips/Wipro or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 132 | S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Single door, IP-43 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. |
| 133 | S&F as in repair flush mounting factory made VTPN DB 4 way, 240 Volt, Double door, IP-43 protection, IK-09 with metal door with 160 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge. |
| 134 | S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make:Havells /Legrand/L&T or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 135 | S&F as in repair MCB 40-63 Amps, Single Pole & neutral 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make:Havells /Legrand/L&T or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 136 | S&F as in repair MCB 32 Amps, Two Pole240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge. Make:Havells /Legrand/L&T or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 137 | S&F in replacement MCCB 4 Pole 100 Amps, thermal magnetic releasehaving, breaking capacity 25 KA, 415 Volt in the existing feeder pillar box including any addition / alteration to the panel to accommodate the new MCCB & making connections with 25x3 mm copper strip as required from main bus bars,making necessary welding work, metal work for fixing base plate etc and connectionscomplete all as specified and as directed by Engineer-in-Charge.Make:Havells /Legrand/L&T or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 138 | S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulatedunsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuous wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note :Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittingsshall be measured as one length. Make:Havells /Finolex/L&T or equivalent in Techno commercial makes mentioned in Appendix \"A\" here-in-after |
| 139 | M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of GI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade top of pipe with funnel & wiremesh, and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in cement concrete (1:2:4) type B-1 and 40mm thick RCC cover, excavation & earth work complete all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009 including taking down old eathing complete all as specified and directed by Engr-in-charge.Notes :- (i) Cost of GI wire upto 7.5m is included in this item. (ii) PCC 1:2:4, Excavation, earthwork is included in the quoted rate of this item.(iii) Cost of GI tubing upto 7.5m is included in the quoted rate of this item.(iv) Outer edge of earth pit chamber shall be 1.5 metre away from the outer edge of PCC chamber.(v) Minimum weight of reinforcement for RCC cover shall be 1 KG. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
