Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | [B&R PORTION]Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing debries out side defence area complete all as specified and directed by Engineer-in-Charge. |
| 2 | Material and Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick light shade (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and includingcement screed bed 15mm thick in screed bed 1:6 base, complete all as specified and directed by Engineer-in-Charge. |
| 3 | All as per item No 2.00 but in vertical surfaces as in skirting / dadosetc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl. 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 4 | Material and labour for 20-25 mm thick machine cut kota stone slab in flooringon treads, landing laid over 20mm thickcement mortar1:6 screed jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge. |
| 5 | Material and labour for 20-25 mm thick machine cut polished Kota stone slab in single piece for skirting , dado ,riser on vertical surfaces and over 15mm thickcement mortar1:3 backing coat jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing befor fixing of kota stone complete all as specified and directed by Engineer-in-Charge. |
| 6 | Material and Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and includingcement screed bed 15mm thick in screed bed 1:6 base, complete all as specified and directed by Engineer-in-Charge. |
| 7 | Material and labour forcoloured glazed ceramic tiles coloured of size 300x 450x 7mmthick in vertical surfacesand jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 10mm thick in cement plaster 1:4 complete all as specified and as directed. |
| 8 | Supply andfixing of pre-painted galvalume aluminium zinc coating GI based corrugatedsteel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa tensile strength as in roof covering/cladding to wall, fixed with self tapping screws or J type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi-corrugated sheets etc; complete all as specified and as directed. |
| 9 | Supply andfixing of pre-painted galvalume aluminium zinc coating GI based galvanised plain mild steel sheeting 0.50 mm thick of any colour, having 550 Mpa tensile strength as in roof covering/ ridges and fixed with self tapping screws or J type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi-corrugated sheets etc; complete all as specified and as directed. |
| 10 | Supply and fixing,structural rolled mild steel Fe 410-00 (Gde E-250) as in roof trusses(framed), trussed, purlin,, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, agnle, channel or flat section)including distance pieces, cleats etccomplete all as specified and directed. |
| 11 | Demolition of brick work built in cement mortar or cement lime mortar including all pillars, quoins etc., complete all as specified and directed by Engineer-in-Charge. |
| 12 | Material and Labour for Brick work with sub class ‘B’ bricks, locally known as “Awwal” straight or curved on plain exceeding 6 metre mean radius in cement mortar (1:6), complete all as specified and directed by Engineer-in-Charge., complete all as specified and directed by Engineer-in-Charge. |
| 13 | Material and Labour for Brick work with sub class ‘B’ bricks, (Except brick) locally known as “Awwal” straight or curved on plain exceeding 6 metre mean radius in cement mortar (1:6), complete all as specified and directed by Engineer-in-Charge. |
| 14 | Taking down cement plaster on brick wall/concrete surfaces etc including racking out joints hacking for key scrubing down with water etc of any thickness including dado any description complete all as specified and directed by Engineer-in-Charge. |
| 15 | Material and labour for 15 mm thick rendering other than fair on faces of brick or concrete surfaces in CM 1:4. finishing the surface even and fair without using extra cement.complete all as specified and directed by Engineer-in-Charge. |
| 16 | Material and labour for rendering 15mm thick in 1:6 CM on fair faces of brick work or concrete surfaces of walls finished. Fair andsmooth complete all as specified and directed by Engineer-in-Charge. |
| 17 | Material and labour for 10mm thick rendering in 1:3 cm on ceiling surfces finished even and smooth without using extra cement.complete all as specified and directed by Engineer-in-Charge. |
| 18 | Material andLabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt/loose materials from the bricks and from the joints between the bricks. Prepared surface should be then washed with diluted HCL acid (dilution ratio of 1:50) for three times in a day for two days. After acid wash surface should be allowed to be air dried for one day. NOTE : - Further treatment over the surface so achieved will be carried out only after approved of the same by GE. |
| 19 | Material and labour for effloresence treatment to unplastered wall surface comprising of the following specification complete all as specified and as directed.(a) Prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : -(i) Pidicrete URP of M/S Pidilite. (ii) Sika Latex of M/S Sika.(iii) Nitobond SBR Latex of M/S FOSROC.(b) Immediately after priming the surface PMM (Polymer Modified Mortar) to be applied “BY HAND” while the prime is tacky. PMM should be prepared by mixing one of the following compounds in Cement Mortar 1:3 as per manufacturer’s instructions: -(i) Pidicrete URP of M/S Pidilite.(ii) Sika Latex of M/S Sika.(iii) Nitobond SBR Latex of M/S FOSROC.(c) PMM surface should be allowed to dry for one day. After that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 (selected compound) : 1:5 (Cement) : - (i) Pidicrete URP of M/S Pidilite.(ii) Sika Latex of M/S Sika. (iii) Nitobond SBR Latex of M/S FOSROC.(d) Now apply two coats of one of the following compound over the surface. These compounds are to be used as per manufacturer’s instructions: -(i) Pidifin 2K of M/S Pidilite (ii) Brush Coat of M/S Sika.(iii) Brush Bond of M/S FOSROC. (ii) Every stage of work will be approved by GE, then only next layer will be executed by contractor.NOTES : (a) The efflorescence treatment shall be carried out by the manufacturer or his authorised representative only. (B) The efflorescence treatment shall be carried out after taking down existing plaster redoing external/internal plaster under respective Items. (b) Make: Pidilite, DR Fixit or Equivalent make as approved by GE. |
| 20 | Material and labour forrough cast plaster on exterior walls in two layers, under layer 10mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm Rough cast plaster with sand gravel as specified as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the surface complete all as specified |
| 21 | Material and labour for two coats of cement base paint over a coat of alkali resistant primerof new surfaces of walls and including preparationcomplete all as specified and directed by Engineer-in-Charge. |
| 22 | Material and labour for preparation new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer applying with rolleretc complete all as specified and directed by Engineer-in-Charge. |
| 23 | Material and labour for preparing and complete removal of existing old plastered surface of wall and applying twocoats of cement base paintincluding chalk whitener and one coat of putty (1.5 mm thick) etc complete all as specified and directed by Engineer-in-Charge. |
| 24 | Material and labour for preparating and complete removal of existing old plastered surface of wall and applying twocoats of oil bound distemper including chalk whitener and one coat of putty etc complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material and labour for preparingold plastered surfaces of walls and applying one coat of white washing complete as all specified and directed. |
| 26 | Material and labour for preparing New plastered surfaces of walls and applying three coat of white washing complete as all specified and directed. |
| 27 | Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-charge. |
| 28 | Supply and fixing Steel water tubing of 15 mm bore, medium grade galvanized,with all fittings laids in floor with wall and on ceiling, complete all as specifiedand directed. |
| 29 | Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-charge. |
| 30 | Supply and fixing Steel water tubing of 20 mm bore, medium grade galvanized,with all fittings laids in floor with wall , complete all as specifiedand directed . |
| 31 | Material and Labour for cutting chases for concealed water tubing and making good, (cutting not exceeding 10 cm girth) (brick walls) in cement mortar (1:3), complete all as specified and directed by Engineer-in-Charge. |
| 32 | Supply and fixing PVC (SWR) Nahani /Floor trap, 75 mm dia of out let, plain with grating including jointing to waste pipe with solvent cement complete all as specified and directed by Engineer-in-Charge. |
| 33 | Material and Labour for PVC water storage tank 500 Litre capacity HDPE triple layerfixed and hoisted in position on staging or roof complete with locking arrangement, over flow pipe, air lock pipe, Ball valves, high pressure of PTMT with,including dismantling of old tanks of of any description complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply and fixing (in repair) 15mm fancy type, chromium plated, angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, heavy with adjustable wall flange, complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fixing (in repair) stop cock, fancy type, chromium plated, long sank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified and directed by Engineer-in-Charge.(Note : Weight of stop cock shall not be less than 0.575 Kg)(Note : Weight of stop cock shall not be less than 0.575 Kg) |
| 36 | Supply and fixing ( in repair)CP bib tap screwed down high pressure, long body, cast copper alloy, chromium plated`with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed by Engineer-in-Charge. (Note : Weight of bib tap shall not be less than 0.575 Kg) |
| 37 | Supply and fixing (in repair) vitreous china wash down water closet pedestal pattern, White including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fixing (in repair) vitreous china wash hand basin white flat back of size 550x440mm including CI brackets and 15mm chromium plated pillar tap, PVC connection 450 mm long having PTMT nuts and chromium plated waste coupling and making good to disturbed portion including32 mm dia PVC waste pipe etc., complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and fixing Viterous china urinal half stall back or corner type complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securring urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe, grating and union for discharge pipe complete all as specified and directed by Engr-in-Charge |
| 40 | Supply and fixing in repair 10 litre capacity flush polypropylene cistern, white at low level complete with PVC bend/flush pipe and making all connection including taking down existing high/low level cistern with all connections and making good the disturbed surfaces in cement mortar (1:3) to match with the existing surface, complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply and fixing in repair for fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. |
| 42 | Supply and fixing, in repairs, 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC bldg Board or commercial plywood, fixedwith aluminium angled frame and two CP MS hanging arrangements all complete all as specified and directed by Engineer-in-Charge. |
| 43 | Supply and fixing in repair chromium plated towel rail600mm long complete as specified and directed by Engr in charge. |
| 44 | Supply and fixing in repair Soap dish, any type, fixed to plugs with chromium plate brass screws complete as specified and directed by Engr in charge. |
| 45 | Supply and fixing in repair cast copper alloy, chromium plated shower rose including long pipecomplete as specified and directed. |
| 46 | Supply and fixing in repair 32/38 mm PVC waste pipe for urinal , wash hand basin and sink complete all as specified and directed. |
| 47 | Supply and fixing (in repair) PVC connections 450 mm long and 15mm diaPTMT with PVC washers on both ends, complete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply and fixing in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12mm wide and chromium plated brakects guard and railing 60cm long fixed in repairs complete as specified and directed by Engr in charge. |
| 49 | Demolition and breaking up drain pipes100/75 mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all asspecified. |
| 50 | Supply and fixing PVC (SWR) 110 mm pipe single socket in any length with rubber ring joints fixed to wall or infloors complete as specified and directed by Engr in charge. |
| 51 | Supply and fixing PVC (SWR) bends 110 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply and fixing PVC (SWR) 75 mm pipe single socket in any length with rubber ring joints fixed to wall or in floor complete all as specified and directed by Engr in charge. |
| 53 | Supply and fixing PVC (SWR) bends of 75mm radius, complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing 75mm PVC (SWR) junction single,(Single T) equal or unequal provided with access door, complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supply and fixing PVC (SWR) vent cowl of 75mm dia, complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal of 110mm dia with access door all as specified and directed |
| 57 | Supply and fixing PVC (SWR) vent cowl of 110mm dia, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Supply and fixingin repair Ball brass valves,of 20mm bore high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), area not exceeding 1.5 Sqm each and removal from site including iron mongry hold fasts etc., complete all as specified and directed by Engineer-in-Charge. |
| 60 | Taking down wooden chowkats or frames with shutter (without taking off shutter from the frames), areaexceeding 1.5 Sqm and not exceeding 4.00 Sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 61 | Taking down shutter of any descritption exc 1.00 sqm each but not exc 2.00 sqm each including removal from site, complete all as specified and directed by Engineer-in-Charge. |
| 62 | Supply andfixing of aluminium alloy anodized (powder-coated) window frame with double shutters open able type, with aluminium sections as specified for casement windows with double shutters including aluminium alloy anodized snap type beads, handles, stainless steel hooks and eyes, aluminium anodized barrel tower bolts, glazing clips, joint cleats, rubber packing, gaskets etc for series-B “ Jindal” section numbers for casement window.complete all as specified and directed comprising of followings :-(a)Frame of section 101.6mm x 44.45mm x 2.10 mm thick and section for shutter 47.62 mm x 44.45 mm x1.95 mm thick.(b)Mullion 53 mm x 52 mm x 2 mm thick not less than 1.065 kg/mertre.(c)Glazing clip weighing 0.259kg/mtr.(d)Window shall be provided with 02 Nos. of tower bolt for single leaf and 03 Nos. of tower bolts for double leaf. Tower bolts shall be aluminium alloy anodized weighing 0.302kg/mtr. Handles shall be aluminium anodized ‘D’ type handle of size 98 mm and thickness 2.37mm weighing 0.875kg/mtr and 01 no for each open able leaf. Notes :- Glass pane shall be measured and paid separately. |
| 63 | Supply and fixing of aluminium partition wall, 60 micron powder coated sections, (minium thickness of powder coating shall be 50 microns) fabricated size of members 100 x 44.4 x 2.0 mm including making provision of opening etc; and all necessary cleats, panel inserts not more than 1.44 sqm and arrangement to receive with and including 5.5 mm thick sheet glass and 19 mm thick pre-laminated particle board with aluminium beading, glazing cleats and stainless steel screws rubber gaskets, beading etc; complete all as specified and directed by Engineer-in-Charge. |
| 64 | Supply andfixing of aluminium alloy anodized (powder-coated) door frame and shutters with hollow aluminium anodized sections and thickness of section exec 1.5mm thick as specified including aluminium alloy anodized snap type beads, dish type door handles, glazed clip, jointing cleats, rubber packing, gasket, dead lock 4 levers, 02 Nos aluminium alloy anodized tower bolts to each leaf etc. including fixing frame to wall/RCC members etc. with rawl plugs complete all as specified and directed by Engineer-in-Charge. Sections of frame and door shall be as follows : -(a)Door Frame single groove 101.6 mm x 44.45 mm x 2.15mm thick (b)Shutter top 47.62 mm x 44.45 mm x1.95 mm thick. (c)Shutter bottom 114.30 mm x 44.45 mm x 2.1 5mm thick.(d)Shutter vertical 85 mm x 44.45 mm x 1.80 mm thick.(e)Shutter middle 83.5 mm x 44.45 mm x 2.40mm thick.(f) Gauging clip weighing not less than 0.097kg/metre.Note :- Glass pane shall be measured and paid separately. |
| 65 | Supply andfixing of 5.5 mm thick tinted glass in square exceeding 0.5 sqm in each pane with heat reflecting properties, black glass film of 50 micron, fixed to aluminium frame with glazing clips, etc. complete all as specified and directed by Engineer-in-Charge. |
| 66 | Supply and fixing of anodised aluminium grill of daimond size 100x100mm of dia 6mm including necessary joining cleats, anodised aluminium snap beading screws, complete all as specified and directed by Engineer-in-Charge. |
| 67 | Supply and fixing Steel window box type using ERW hollow \"P\" section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick,jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable complete inclusive of guared bars 12mm square bar including taking down old unserviceable windows Make : Manufactured by Ram Fabricators Pvt Ltd Panchkula (Hr.) or M/S TEE PEE Enterprises Ludhiana (Pb.)Note: (i) For the purpose of measurement and payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery (iii) Glazing, wire mesh and painting grill shall be measured and paid for separately. |
| 68 | Supplyand fixing Steel windows or ventilators, fixed type, with glazing bars all as specified and directed. |
| 69 | Supplyand fixing3mm Sheet glass, ordinary quality, in squares not exc 0.5 sq. m eachand glazing with beads fixed with metal panel pins all as specified and directed. |
| 70 | Supply and fixing Pressed steel frames for doors of size 165mm x 60mmwith one or more rebates including necessary fixing lugs, hinges, lock strike plate, supplied and fixed. |
| 71 | Material and Labour IInd class hardwood factory made 30mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) supply and fixed to choukats complete all as specified and directed by Engineer-in-Charge at site. |
| 72 | Supply and fixing for galvanized mild steel wire cloth with 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with finned tacks or galvanized wire staple complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply and fixing for 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides completeface is covered with decorative face veneer with lipping/frame to match all as specified. |
| 74 | Supply and fixing factory made 35mm thick 2nd class hardwood plain frame paneled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both sides.The size of rails stile as per I:S:1003 (Part I) kiln seasoned and chemically treated. Note : Manufecturers Test cert to be submitted before incorporattion. |
| 75 | Supply and fixing250 mmaluminum anodised sliding door bolts, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed by Engineer-in-Charge. |
| 76 | Material and labour forpreparing new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint(first quality) over a coat of primer complete all as specified and directed. |
| 77 | Material and labour for painting new wooden surfaces of any description not otherwise described over 10cm width of girth by applying two coats, of synthetic enamel paint over a coat of pink primer including preparation complete all as specified and directed by Engineer-in-Charge. |
| 78 | Material and labour forpreparing old steel surfaces of any description , over 10 cm width or girth and applying one coats of synthetic enamel paint(first quality) complete all as specified and directed |
| 79 | Material and labour for painting old wooden surfaces of any description not otherwise described over 10cm width of girth by applying two coats, of synthetic enamel paint including preparation complete all as specified and directed by Engineer-in-Charge. |
| 80 | Supply and fixing factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number and minimum 02 Nos. for horizontal member), complete all as specified and directed by Engineer-in-Charge. |
| 81 | Supply andfixing Factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm plain colour PVC sheet on back face includingfixing in frame at site with 03 Nos SS hinges, 02 Nos aluminium tower bolt 200 mm, 02 Nos aluminium handle 150 mm for each shutter all as per specification and drawing complete all as specified and directed by Engineer-in-Charge. |
| 82 | Material and Labour for PCC 1:2:4 type B-1, (using 20mm graded mechanically crushed stone aggregate) as in bed blocks for hold fasts, complete all as specified and directed by Engineer-in-Charge. |
| 83 | Supply andfixing mild steel butt hinges of 100mm length, cold rolled, medium weight,complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply and fixing for Aluminium anodised, 200mm long barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply and fixing 150mm long extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed by Engineer-in-Charge. |
| 86 | Supply and fixing 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified and directed by Engineer-in-Charge. |
| 87 | Supply and fixing in repair 300mm, ordinary rat tail rod pattern springs including roller and roller plate completeif fixed to steel/ concrete chowkats with flat iron 40x3 mm size 75 cm long with necessary bolts, etc. complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply and fixing in repair mild steel 25 mm tubular rod in Drapery rod, 1.6mm fancy type includinggolden colour brakets,latto and wall to wall socketetc complete all as specified and as directed by engineer-in-charge. |
| 89 | Supply and fixing as in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed by Engineer-in-Charge. |
| 90 | Material and labourhacking out old broken glass (Any thickness ,size,quality or descriptionfrom metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified and directed by Engineer-in-Charge. |
| 91 | Supply and fixing Sheet glass, 3mm ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane andsheet glass is ground or obscured or frosted, on one side, complete all as specified and directed by Engineer-in-Charge. |
| 92 | Supply and fixing in repair 5mm thick hollow interlocking wall panelling of width 250mm for wall panelling for fixing on to wall with screws and solvent alonghwith corner and u channel beading of colour choice including diamantling old beading/panelling all as specfied and directed. Note : Rate will be inclusive ofany electrical fitting /boardeffected and refixing the same after rectification |
| 93 | Supply and fixing of semi perforated false ceiling 12 mm thick with micro tegular edged at all height with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and pattern having moisutre content less than 2%, humidity resistance of 99%, NRC 0.60 to 0.85 as per IS 8225-1987, non combustible as per BS 475 (Part-4) 1970 and light code description unit code No 429 Sub Head 26. New Technologies and materials reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metal T -grid of hot dipped galvanised iron section of 0.33 mm thick ( galvanised @ 120 gms/ sqmincluding both sides) comprising of main T- runners of size 15x 32mm of length 3000mm, crossT of size 15 x32 mm of length 1200mmand secondary intermediate cross T of size 15 x 32 mm of length 600 mm to from grid module of size 600 x 600 mm, suspended form ceiliing using galvanised mild steel items (Galvanised @ 80 gm/sqm) i.e. 50 mm long, 8mm outer diameter M-6 dash fastners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85 x 25 x 2mm.galvanised iron perimeter wall angle of size 24 x 24 x 0.4 mm of length 3000 mm to be fixed on perimeter wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall SS screws.The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge including dismantling existing asbestos sheet false ceiling textile coverings including frames (if any) and cover fillets complete all as specified and directed by Engineer-in-Charge. |
| 94 | Material and labour for cleaning the roof top surface ,brick tileby Wire brushing and cleaning theroof surfaces with water including removing vegetation roots , sweeping clean and washing down with water to remove dust etc and filing of damaged joints tiles in CM1:4complete all as specified and directed by Engineer-in-Charge. |
| 95 | Material andlabour for plain cement concrete,1:2:4type B-0 using 12.5 mm graded crushed stone aggregate as in roof padding, levelling coarse and finished top surface finished even and smooth including necessary form work complete all as specified and directed by Engineer-in-Charge. |
| 96 | Material and labour for 3mm thick APP (atactic polyproylene polymer) modified prefabricated five layer weight not less than 3.60 kg/sqm water proofing membrane black finish reinforced with non woven polyster matt and applying on top of it one coat of hot straight run bitumen grade30/40 (Grade S-35) conforming to IS-73 at the rate of 1.2 kg/sqm, make as approved consisting of a coat bituminous primer @ 0.40 ltr/sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25\"C temperature and viscosity 70-160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end , the layer membrane shall be laid using butane gas torch and sealing all joints etc after preparing the surface complete all as per standered parctice as per manufacture\"s instructions The vital plysical and chemical parameters of the membrane shall be under:- (i) Joint strenth in longitudinal and transverse ditection at 23\"c at 650/450 N/5cms (ii) Tear strength in longitudinal and transverse direction at300/250N/5 cms. Softing point of membrane nor less then 150\"c when tested in according with ASTM(d-5147) (iii) The laying if membrane shall be got down through the authriosed applicator or manufactures of membrane only complete all as spcified and directed. |
| 97 | Dismantling timber scantling 40 sq.cm and over in section in any position complete all as specified and as directed. |
| 98 | Dismantling wrought iron or mild steel work of any description notherwise provided for opurlin/rafters, gates, staircases railings, framed truss etc , complete all as specified and directed by Engineer-in-Charge. |
| 99 | [E&M PORTION]Taking down carefully any type of battens or conduit point wiringwith or without conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing surface complete all as specified and directed. |
| 100 | Taking down Ceiling fan any size or any type and deposited to MES store yard complete all as specified and directed. |
| 101 | Taking down old and unserviceable submain wiring any size /type including earth wire complete with batten/conduit etc complete all as specified and directed. |
| 102 | Taking down old unserviceable VPTN MCCB DB/MCB DB TPN 4way /MCB SPN 8way any of size/capacity complete all as specified and directed. |
| 103 | Taking down old unserviceable MCB SPN/MCB SP/MCB 4P of any size/capacity complete all as specified and directed. |
| 104 | Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLSH (FIRE Retardant Low Smoke and low Halogen), PVC insulated and unsheathed stranded cable drawn through and including non metallic,medium grade PVC concealed conduit not less than 20mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxeswith GI metal flushboxes made out of 1.2mm thick of any module from 2 to 18module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly coated with two coats of anti corrosive paintincluding modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over metal flush boxes for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbedsurfaces as per existing for one light / fan / Bell point contorlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLSH (FIRE Retardant Low Smoke and low Halogen) copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dollywith suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and as directed.NOTES:- 1. Switch, socket and fan regulators to be measured and paid for separately.2. All chases will be cut by chase cutter only. |
| 105 | Description all as per item No 104.00 here in before but one 5 pin, 5 Amp switch socket out let on the same board with other switches, complete all as specified and directed by Engineer-in-Charge. |
| 106 | Description all as per item No 104.00 here in before but one 5 pin, 5 Amp switch socket out let on the independent board, complete all as specified and directed by Engineer-in-Charge. |
| 107 | Description all as per srl item No 104.00 above but point wiring for one socket out let 15&5 Amps (independent) controlled by one switchwith using 2.5 Sq mm (nominal area) stranded copper conductor complete all as specified and directed. |
| 108 | Supply and fixing modular switch flush type, 5 Amps, single pole, one way 1 module complete all as specified and directed . |
| 109 | Supply and fixing modular switch flush type, 16 Amps, single pole, one way 1 module complete all as specified and directed . |
| 110 | Supply and fixing modular socket , 5 pin, 5 Amps, multipurpose 2module complete all as specified and directed. |
| 111 | Supply and fixing modular socket , 5 pin, 6/16 Amps, multipurpose 2module complete all as specified and directed. |
| 112 | Supply and fixing ceiling rose, surface bakelite, size as per relevant IS, three terminals complete all as specified and directed. |
| 113 | Supply and fixing modular fan step regulator 120W 2 module complete all as specified and directed. |
| 114 | Supply and fixing in repair lamp holder,insulated body, with back PVC rectangular block for fixing of holder with screw complete all as specified and directed. |
| 115 | Supply and fixing sheet metal enclosures vertical distribution boardVTPN, (MCCB DB) 4 ways, double door , 415 volts with 200 amps rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and includingadjustable thermal setting MCCB 4 Pole, 125 Amps 25 KA as incomerand MCB sas out going complete with making suitable size of MS cabinet 2 mm thick dully grouted on the wall (flush) with opening arrangementincluding and making connection with suitable size of lugs and making good the disturbed surface matching with existing surface complete all as specified and directed by Engineer-in-Charge. |
| 116 | Supply and fixing MCB DB sheet enclosureDouble Door, single pole and neutral 240V with 100 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 as per IS 8623without MCB and with enclosure blank plates for unusedway suitable for 8 way complete all as specified and directed. |
| 117 | Supply and fixing MCB DB sheet enclosure Double Door, single pole and neutral 240V with 100 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 as per IS 8623without MCB and with enclosure blank plates for unusedway suitable for 12 way complete all as specified and directed. |
| 118 | Supply and fixing MCB, single pole and neutral, 240 Volts 40-63 Amps,10KA \"B\" curvecomplete all as specified and directed. |
| 119 | Supply and fixingMCB, single pole, 240 Volts 06 to 32 Amps,10KA\"B\" curvecomplete all as specified and directed . |
| 120 | Supply and fixing MCB SP single pole, 240 volts, 50 Hz, breaking capacity , 40-63 Amps, complete all as specified. |
| 121 | Supply and fixing of LED light fitting 1x20W (lumen efficacy of >100 lm/W) , 220V, AC with aluminium housing with batten type with driver , holder including 20W LED tube light for connecting up with three core flexiable copper conductor cable of suitablae size from celing rose to connector complete all as specified and directed by Engineer-in-Charge. |
| 122 | Supply and fixing LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engineer-in-Charge. |
| 123 | Material and labour for Subwiring with two single core 4 Sqmm stranded copperconductorFRLSH PVC insulated and unsheathed cabledrawn in 25mm dia, medium grade, PVC conduit concealed in wall for sub main connection including 4Sqmm PVC insulated unsheathedcopper conductoras earth wire complete all as specified and directed by Engr-in-charge. |
| 124 | Material and labour for Subwiring with two single core 6 Sqmm stranded copperconductor FRLSH PVC insulated and unsheathed cabledrawn in 25mm dia, medium grade, PVC conduit concealed in wall for sub main connection including 6.0SqmmPVC insulated unsheathedcopper conductoras earth wire complete all as specified and directed by Engr-in-charge. |
| 125 | Supply and fixing LED street light fitting 30/35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge. Note:- Bracket with clamp,nut & bolts deemed included in quoted rate. |
| 126 | Hanging only ceiling fan after completion of civil work rubbing withsand paper, taking off old paint with the help of chemicals and painting the ceiling fan with one coat of superior quality fan with one coat of superior quality synthetic enamel paint complete all as specified and directed by Engr-in-Charge |
| 127 | Supply and fixing ceiling fans, AC, single phase, 230V, 50Hzs , copper wounded of 1200mm sweep with Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) technology , including down rod `U\" clamp, 3 core PVC flexiable cable 1sqmm for making connection of fan and hanging the fan in clamp, connecting with exisiting electrical connection all as specified and directed by Engineer-in-Charge. |
| 128 | Excavation in trenches in soft/loose soil not.exc 1.5 m wide and not.exc 1.5 m in depth for foundation of poles,cable laying etc, including forming bottom surface to required level and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge. |
| 129 | Returning, filling in soil/loose soil including spreading, leveling,watering and well ramming in layers not .exceeding 25 cm thick complete all as specified and directed by Engineer-in-Charge. |
| 130 | Removing of surplus spoil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge. |
| 131 | Material and labour for sand cushioning with a layer of sand 80mm thick before laying of cable and 150mm thick after laying of cable to trenches and punning down complete all as specified and directed by Engineer-in-Charge. |
| 132 | Material and labour cover to underground cable with one layer of bricks using sub class \"B\" bricks laid flat acorss the cable complete all as specified and directed by Engineer-in-Charge. |
| 133 | Supply and fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium, stranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed twin core 16sqmm 4 core nominal cross section in service connections complete all as specified and directed by Engineer-in-Charge. |
| 134 | Supply and fixing of LED lamp 9 watt B-22 base complete including taking down old existing lamp any type complete all as specified and directed by Engineer-in-Charge. |
| 135 | Material and labour for earthing with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25 m below normal GL with the top edge of the plate not less then 1.5 m below the normal GL connected to GI wire 4mm dia protected by 15mm GI pipe (light grade) and watering pipe 20mm bore GI pipe (light grade) and chamber with PCC (1:4:8) type D2 using 40mm graded stone aggregate, coping with (1:3:6) type CI using 20mm graded stone aggregate and with RCC pit cover (50 mm thick) in 1:2:4 type B1 using 20mm stone aggregate, reinforced with 8mm for MS bar at 80mm c/c both way in lieu of CI pit cover with angle iron frame including excavation and earth work and removal of surplus soil of earth complete all as shown in electrical plate No 3 of SSR Part I and including charcoal dust, common salt and earth lead connected to earthing test point testing of earthing completeall as specified and directed. NOTE: Main earthing lead and protection GI pipe from earth electrode to test point up to7.5 m is to be provided and the cost for the same shall deemed to be included in the above quoted rate. earthing lead beyond 7.5 m shall be measured and paid for separately under respective item. |
| 136 | Material and labour for refixing of LED tube lights fitting,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 137 | Supply and fixing recess/ surface mounted LED flat panel 2\" x 2\" with high efficient LEDs and glare free full decorative light fitting, 36 watt, energy efficient provided withincluding LED36 watt withprovision of 2/3 core PVC copper conductor cable 1.5 Sqmm size to light fitting and completeincluding disconnecting and taking down existing light fitting and removal complete all as specified and directed. |
| 138 | NOTE:- Amount of credit ofRs. 1,60,131.00 for retrieved materials is mentioned in Schedule of Credit Page No 21.00 & 22.00 of tender documents in pdf form which will be deducted offline while acceptance of tender. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
