Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Common Items For Nirbhay Vihar and Yogendra Vihar works |
| 2 | Rectifying complaints of blockage of bathroom / kitchen / WHB / urinals / WCs etc of any pattern and make it fully functional. The blockage shall be cleared all as specified and directed.(a) The period of rectifying each complaints is maximum 48 hrs and Rs 100 / each complaint will be charged in case of failure to rectify the complaint in the stipulated period.(b) The contractor shall provide adequate labours and tools to rectify the complaints.(c) The sludge obtained during rectifying the complaints shall be deposited beyond the periphery of defence land. |
| 3 | Rectifying complaints blockage of manholes depth not exc 1.00 mtr incl removing all sludge as specified and directed.(a) The period of rectifying each complaints is maximum 48 hrs and Rs 100 / each complaint will be charged in case of failure to rectify the complaint in the stipulated period.(b) The contractor shall provide adequate labours and tools to rectify the complaints.(c) The sludge obtained during rectifying the complaints shall be deposited beyond the periphery of defence land. |
| 4 | M&L for Providing factory made cover full floor mediun duty weightSquare/rectangular (size 500mm x 900mm) thickness not less than 75mm set in CM 1:6, as in cover slabs (for manhole, drainsetc) with plain fair faces, with angle iron frame alround all as spd. |
| 5 | M&L for coloured machine pressed rubber moulded precast concrete interlocking (red/yellow) paver block any shape and size having glossyfinish of 60 mm thickness M-35 Grade (ISI Mark) grey cement and pigment complete incl demolition of existing hardstanding complete all as specified and directed. |
| 6 | M&L 30 mm thick Sand filling under floors or in foundations including watering and consolidation all as specified and directed |
| 7 | M&L for brick work with fly ash bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 including demolition of brick work built in cement mortar including precast concrete articles complete all as specified and directed. |
| 8 | M&L for Ready mix plaster 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair complete on walls all as specified and directed. |
| 9 | M&L for ready Mix plaster 15 mm thick in cement mortar 1:6 on brick wall or concrete surface including finishing the surface even and smooth without using extra cement including taking down cement or cement lime plaster on walls any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed. |
| 10 | M & L for old plastered surface of walls and applying one coat Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. and directed |
| 11 | M & L for old plastered surface of walls and applying subsequent coat of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. and directed |
| 12 | M&L for preparation of old painted surface of wood and wood based material of any description area exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 13 | M&L for preparation of old painted surface of steel/iron of any description area exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 14 | Taking down steel tubing and Supply and fixingof 15 mm dia (Nominal bore) galvanised iron water tubing \"medium grade\" with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including necessary cutting and chaseing in brick wall for concealed including making good complete all as specified and directed. |
| 15 | Taking down steel tubing and Supply and fixinginof 20 mm dia (Nominal bore) galvanised iron water tubing \"medium grade\" with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including necessary cutting and chaseing in brick wall for concealed where required including making good complete all as specified and directed. |
| 16 | S & F in repairPVC valveless syphonic double action type flushing cistern ISI marked, low level white with inlet ball valve, float and handle including brackets complete all as specified and directed. |
| 17 | Supply and fixedin repairs 600x450mm beveled edges mirror of selected quality mounted on 4mm thick AC building board/ PVC frame or 6mm thick ply fixed to wall with rowl plug and screws complete all as specified. |
| 18 | S&F in repair PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed. |
| 19 | S & F in repairs of Bottle trap of PTMT having minimum water seal of 25mm (Minimum weight 32mm-260gms/ 40mm-270 gms) as per direction of Engr-in-Charge. |
| 20 | S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall installed inside duct covered with iron sheet at site complete all as specified and directed. |
| 21 | Taking down chowkhat frame with shutter ( without taking out shutter from the frame) n exc 1.50 Sqm and removing from sites complete all as specified and directed. |
| 22 | Taking down chawkhat frame with shutter (iron shutter - without taking out shutter from the frame) exc 1.50 Sqm but n. exc 4 sqm each and removing from site complete all as specified and directed. |
| 23 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed. |
| 24 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mmmprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 mm2 and resistance to spread of flame of Class A category with property of being mite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 25 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mmmprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 mm2 and resistance to spread of flame of Class A category with property of being mite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length omplete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).complete all as specified and directed.Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 26 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, and 4 no. stainless steel butt hinges all as per direction of Engineer-In- Charge. |
| 27 | S&F 30 mm thick Factory made solid WPC (Wood plastic Composit)both side pre-laminatedmoulded gauged door shutter min density 650kg/Cum with wire mesh in any number of division with brown wood grain texture including SS wire mesh (G-304) 0.36 mm minimum dia of wire and average width of aperture 1.4 mm and XPM aluminium mesh for additional strength and safety shall be fixed with 15 x 15 square tube in side rails with screwing 8 x 28heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws.The density shall be as per manufacture instruction complete all as specified and complete all as specified and directed. |
| 28 | S&F two(double) legged floor door stopper of aluminum body & tougues with hard drawer steel spring fixed in floor of 140mm complete all as specified and directed.. |
| 29 | S & F Mild Steel, chromium platedsliding door bolt 250mm long with hasp and staple (bolttype) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as specified. |
| 30 | S & F Continuous (piano) hinges of size of flap 30mm mild steel, bright finish or elecrogalvanised fixed with screw to timber frame work complete all as specified and directed |
| 31 | S & F Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate for cup board / cabinet shutters complete all as specified and directed |
| 32 | Material and Labour for 4 mm thick plain sheet glass ordinary quality in square or rectangle not exceeding 0.5 sqm each pane including glazing with putty area fixed to frame work including hacking out old broken glass of any description and thickness from aluminium frames fixed with aluminium beads complete all as specified and directed. |
| 33 | Items for Nirbhay Vihar Works |
| 34 | M & L for Brickwork with fly ash bricks, old size bricksstraight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 including demolition of brick work built in cement mortar complete all as specified and directed. |
| 35 | M&L PCC 1:2:4,type B0 using 12.5 mm graded stone aggregate as in roof kerbs / benching / coving and roof padding over roof surfacesetc rounded or chamfered on edges, complete, all as directed. |
| 36 | M&Lfor joint free Non skid ceramic coloured floor tiles shade as approved size 7-8mm thick area of each tile exc 0.11 sqm but not exceeding 0.18 sqm set on 15mm thick in neat cement screed(1:6) slurry and pointed incl white or coloured cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding , removing and rubbish off the premises etc complete all as specified. |
| 37 | M&Lfor Non skid ceramic colour floor tiles shade as approved size 7-8mm thick area of each tile exc 0.06 sqm but not exceeding 0.11 sqm set on 15mm thick in near cement screed(1:6) slurry and pointed incl white or colour cement to match including dismantling floor, hearth or wall tiling including cement mortar bedding , removing and rubbish off the premised etc complete all as specified. |
| 38 | M& L for Vitrifiedtiles double charged 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredcement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding , removing and rubbish off the premised etc complete all as specified. |
| 39 | All as per above item No-40 buton vertical surfaces including 10mm thick screed plaser in CM 1:4 , complete all as specified and as directed. |
| 40 | M&L for joint free glazed coloured DIGITAL GLOSSY tiles, superior quality of size 300 x 450 x 7mm thick/300 x 600 x 7mm thick, in vertical surfaces etc., set andjointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 and dismantling of existing tiles complete all as specified and directed. |
| 41 | S&F in repair bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed. |
| 42 | S&F in repair of CP alloy chromium plated angle valve/ two way angle valve long body for 15 mm bore pipe with capstan head long screwed shank including CP cover plate fancy type all as specified and directed |
| 43 | S&F in repair hand shower (health faucet), superior quality, round shape, single flow, brass chromium plated, with 1m long flexible pipe with wall hook bracket etc. and all fittings for EWC complete all as specified and directed. |
| 44 | S&F in repair 5 mm thick sheet glass corner shelf assembly, fancy type, sheet glass shelf of size 250x250mm, with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed. |
| 45 | S&F in repair 5 mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed. |
| 46 | S & F in repairsBrass spindle for bib taps/ concealed cock/ Pillar tap etc of any type or pattern complete all as specified and directed. |
| 47 | S&F in repair 15mm bore pillar cock fancy type, screwed down high pressure with or without letters hot or cold with long screwed shank, Swan neck type and fly nuts screwed for iron pipe ISI marked complete all as specified. |
| 48 | S&F in repair 20 mm bore gun metal ball stop gate valve with lever type, screwed both ends for iron pipe including testing complete all as specified and directed. |
| 49 | S&Fin repair Vitreous China wash down water closet pan, pedestal pattern, white, with \"P\" or \"S\" trap, excluding flushing cistern and flush pipe, with plastic water closet seat cover, white, closed pattern with flat bottom and cover, fixed with MS chromium plated hinging deviceincluding connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified anddirected. |
| 50 | S & F in repair ofplastic water closet seat cover (any size/ shape) closed patternwithflat bottomand coverand mild steel chromium plated oraluminised hanging device complete all as specified and directed. |
| 51 | S & F in repair ofplastic water closet seat cover for Vitreous China, semi-pedestal pattern (Anglo-Indian Type) and mild steel chromium plated oraluminised hanging device complete all as specified and directed. |
| 52 | S&F in repair CP brass tubular towel rail 20mm dia, anytype, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed. |
| 53 | S&F in repair multilayered Rotational moulded polyethlene water storage tanks of capacity 500 litres(cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20/ 25 mm dia ball PVC valve high pressure with polythene float and dismantling of existing PVC tank of any capacity complete all as specified. |
| 54 | S&F PVC water tank cover 500/ 1000ltrs complete all as specified. |
| 55 | Supply & Fixing in repair CP Brass shower rose fancy type 125mm thick with or without swivel joints any size including fixed to steel pipe or union as directed. |
| 56 | Supply & Fixing in repair sink without drainage board size 560x410x200 mm made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes pipe & coupling etc incl bedding in cementmortar to draft wall or cantilever brackets and connection union to pipe all as specified and directed. |
| 57 | S & F in repair stainless steel kitchen plate rack made out of 1.00 mm thick stainless steel of size 900x750x250 mm including screws and weight not less than 5.00 Kg complete all as specified and directed. |
| 58 | S&F in repair float ball 15 mm bore high presure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 142 grams) complete all as specified and directed. |
| 59 | S&F in repair float ball 20 mm bore high presure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) complete all as specified and directed. |
| 60 | S&F WPC cabinet and cupboard in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet consisting of carcass 18mm thick WPC sheet & provision of shutters made out of 18 mm thick one side decorative laminated WPC sheet density not less than 600 kg/ Cum all required brackets SS screws etc.The panels shall be fabricated using adhesive and screws where ever required.All the edgesshall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish including all necessary fittings and required knobs in each shutters as per site requirement and as per makeand specification mentioned as per drawing and all are specified and directed by Engineer-in-charge on site. |
| 61 | S & F in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed. |
| 62 | S&F 100 mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate andfixed with screws complete all as specified and directed. |
| 63 | S&F 100mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed. |
| 64 | S & F in repair of Continuous (piano) hinges, mild steel, bright finished or electro galvanised, with width of flap 30mm when open, and fixed with screws complete all as specified and directed. |
| 65 | S & F in repair of ball cateches with 8 mm dia steel bal and brass body and strike plate magnet ball catcher for cup board shutters all as specified and directed. |
| 66 | S&F in repair of 100 mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate andfixed with screws complete all as specified and directed. |
| 67 | S&F in repair of 100mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed. |
| 68 | S&F in repair 25mm dia stainless steel curtain rod (weight not less than 0.15 Kg / RM) superior quality with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed. |
| 69 | S&F in repairs of 0.36 mm dia stainless steel wire cloth (G-304) with average width of aperature 1.40 mm and fixed with stainless steel wire staples or moulded beading (change wiremesh in iron window upto IIIrd floors) complete all as specified and directed. |
| 70 | M&L for preparation of old plastered or unplastered surface of ceilingandapplying one coat of white wash complete all as specified and directed. |
| 71 | M&L for preparation of old plastered or unplastered surface of ceilingandapplying one coat of oil bound distemper complete all as specified and directed. |
| 72 | M&L preparation of New plastered surface of walls andapplying two coats of oil bound distemper complete all as specified and directed. |
| 73 | Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick \"D\"Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyster paint of 12-16 microns thick and back coated with 5-7 microns thick alkyed backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48x25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade) 0.36 mm minimum dia of wire and average width of aperture 1.4 mm. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10 mm square guard bars with 6\"(152.4mm) pitch, complete for finished item of work including of all taxes, design as per direction of Engr-in-Charge. |
| 74 | S & F of Stainless steel ISI Mark Butt hinges 100mm size as directed. |
| 75 | S & F of 200mm long MS Cromium plated barrel tower bolts of extructed section as directed. |
| 76 | Supply& fix MS ordinary pattern spring \"plate type\" including roller & roller plate complete as directed. Make -\"Ritz\" |
| 77 | S & F of 200mm size Extruded aluminium alloy powder coated handles (As per sample kept in sample room) fancy type, fabricated type, anodised all as per direction ofEngr-in-Charge. |
| 78 | S & F in repairs of Stainless steel ISI Mark Butt hinges 100mm size as directed. |
| 79 | S & F in repairs of Stainless steel ISI Mark Butt hinges 75mm size as directed. |
| 80 | S & F in repairs of 200mm long MS Cromium plated barrel tower bolts of extructed section as directed. |
| 81 | S & F in repairs of 150mm long MS Cromium plated barrel tower bolts of extructed section as directed. |
| 82 | Supply& fix in repairs of MS ordinary pattern spring \"plate type\" including roller & roller plate complete as directed. Make -\"Ritz\" |
| 83 | S&F in repairs of MS Cromium plated sliding door bolt 200mm long with hasp and staple (bolttype) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as specified. |
| 84 | S&F in repairs of MS Cromium plated sliding door bolt 250mm long with hasp and staple (bolttype) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as specified. |
| 85 | S & F in repairs of 150mm size Extruded aluminium alloy powder coated handles (As per sample kept in sample room) fancy type, fabricated type, anodised all as per direction of Engr-in-Charge. |
| 86 | Repairing/ easing to steel window side hung shutter including fixing of left or right MS handle, casement stay 300 mm long , MS tower bolt and welding wherever required asdirection of Engr-in-Charge. |
| 87 | Repairing/ easing to steel Gates of veh garages etc including fixing of MS handle, hinges as fixed earlier and welding wherever required asper direction of Engr-in-Charge. |
| 88 | M&L mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 89 | Repairing/ easing to handle, tower bolts, hing, sliding bolt and like this in door any type n exc 2 Sqm including necessary nails and other likecomplete all as direction of engr-in-charge. |
| 90 | S & F in repair PE AL PE composite Elbow size 12 x 16mm complete all as specified and directed. |
| 91 | S & F in repair PE AL PE composite coupler / union size 12 x 16mm complete all as specified and directed. Make-Nexgen. |
| 92 | S & F in repair PE AL PE composite tee size 32 x 32 x 32mm complete all as specified and directed. Make-Nexgen. |
| 93 | S & F in repair PE AL PE composite tee size 32 x 25 x 16mm complete all as specified and directed. Make-Nexgen. |
| 94 | S & F in repair PE AL PE composite tee size 32 x 25 x 20mm complete all as specified and directed. Make-Nexgen. |
| 95 | S & F in repair PE AL PE composite Female Tee size 12 x 16mm complete all as specified and directed. Make-Nexgen. |
| 96 | S & F in repair PE AL PE joint connector size 12 x 16mm complete all as specified and directed. Make-Nexgen. |
| 97 | S & F in repair PE AL PE joint connector size 20x 25 x 16x 20mm complete all as specified and directed. Make-Nexgen. |
| 98 | S&F\"E\" board everest make 600x600x4mm thick white prelaminated sett embosed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be poweder coated white.The frame work shall comprise of main runner made from 0.33 mm thick GS sheet and of size 24x32x300mm abd soaced at 1200mm centers securely fixed to be structural soffts by approved hangers at 1200 mm maximum centrers.Hangers of GI wire 4mm dia to be fixed by approved rawl plug level and justers and screws etc.The last hanger at the end of each main runner shall not be grater than 450mm from adjacent wall,Flush fitting of 1200mm long cross tee (with double stiching) to be interlocked between main runners at 600mm center to from 1200x600mm modules cross tee longer than 600mm to be supported independtly.600x600mm dodules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee.Tee, perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour including dismantling of false ceiling and boarding any description all as per manufacture insturction. |
| 99 | S&F in repair of CP grating 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified anddirected. |
| 100 | S&F in repairs of CP grating 125mm dia without waste hole (Minimium weight 40 grams) complete all as specified anddirected. |
| 101 | M&L100 mm dia sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed on walls with clamps in repair |
| 102 | M&L75 mm dia sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed on walls with clamps in repair |
| 103 | M&L100mm dia sand cast CI Bends with oval access door/ TEE/ Socket/ Reducer and jointed with neat cement paste in repair |
| 104 | M&L75mm dia sand cast CI Bends with oval access door/ TEE/ Socket/ Reducer and jointed with neat cement paste in repair |
| 105 | S&F in repair 100 mm dia cast iron floor trap/ Nahanai trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as speciifed and directed. |
| 106 | S&F in repair 75mm dia cast iron floor trap/ Nahanai trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as speciifed and directed. |
| 107 | S & F of 100mm bore pipe stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays or hold fast(brass/ stainless steel), including bolts and nuts and securing ends of stays to wall or roof any type complete all as specified and directed. |
| 108 | Rectifying complaints blockage of manholes depth exc 1.00 mtr incl removing all sludge as specified and directed(a) The period of rectifying each complaints is maximum 48 hrs and Rs 100 / each complaint will be charged in case of failure to rectify the complaint in the stipulated period.(b) The contractor shall provide adequate labours and tools to rectify the complaints.(c) The sludge obtained during rectifying the complaints shall be deposited beyond the periphery of defence land. |
| 109 | Rectifying complaints of blockage of sewage lines 100 mm dia of any length & depth and make it fully functional all as specified and directed. |
| 110 | Rectifying complaints of blockage of sewage lines 150 mm dia of any length & depth and make it fully functional all as specified and directed.Note for item no-02,03,109,110 & 1111.The cleaning shall be carried out with mechanized operation by means of diesel / electric operated vehicle mounted hydraulic operated high pressure suction -cum -jetting machines fitted with pump of required capacity and the sludge sucked out with Super Succer Machine of required capacityand sent to storage tanks for further disposal to the authorised disposal site land at any distance and without any additional cost. 2. The sludge deposited in sewage line shall be fully cleaned and disposed off the same outside the MOD land at any distance and without any additional cost , on the same day when it was taken out.The job shall be carried out with safety precaution equipmentand with strict supervision .3. During the mechaized operation , the service provider /Contractor shall be equiped with Gas monitor , nylon rope ladder , torch light and compressor blower etc along with the sewage cleaning truck mounted suction / jetting machine . 4. The unit rate quoted by the contractor shall interalia deemed into the cost of providing skilled driver and operator and supervising engineer including provision of water for jetting & removal of sludge /silt /liquid /mud & sand (in foul position )etc. 5. The contractor shall engage the T & P required for such purposes and intimate to Enginner - In -Charge in writing with Machine No./ Vehicle No. etc for their record and prior approval .Note for item no-113,114 & 1151.The cleaning shall be carried out with mechanized operation by means of diesel / electric operated vehicle mounted hydraulic operated high pressure suction -cum -jetting machines fitted with pump of required capacity and the sludge sucked out with Super Succer Machine of required capacityand sent to storage tanks for further disposal to the authorised disposal site land at any distance and without any additional cost. 2. The sludge deposited in sewage line shall be fully cleaned and disposed off the same outside the MOD land at any distance and without any additional cost , on the same day when it was taken out.The job shall be carried out with safety precaution equipmentand with strict supervision .3. During the mechaized operation , the service provider /Contractor shall be equiped with Gas monitor , nylon rope ladder , torch light and compressor blower etc along with the sewage cleaning truck mounted suction / jetting machine . 4. The unit rate quoted by the contractor shall interalia deemed into the cost of providing skilled driver and operator and supervising engineer including provision of water for jetting & removal of sludge /silt /liquid /mud & sand (in foul position )etc. 5. The contractor shall engage the T & P required for such purposes and intimate to Enginner - In -Charge in writing with Machine No./ Vehicle No. etc for their record and prior approval . |
| 111 | M&L for providing precast RCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone agg as in cover slab for man holes, drains, soak well etc and similar articles etc, set in CM 1:4 with plain faces including chamfered weathering throating etc incl necessary form work and including demolition of old reinforced concrete of any description in any postion not otherwise specifically provided far complete all as specified and directed. |
| 112 | S&F for mild steel deformed bars or TMT bars6 mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 113 | Demoliton/breaking of drain pipes (salt glazed ware,AC or reinforced concrete) set in cement mortar and takingout off trenches and removing the debris from the site all as spd of 150mm dia pipe. |
| 114 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense soil. |
| 115 | all as per items no 116 but depth exc 1.5m and not exc 3 m all as specified and directed. |
| 116 | Removing of material exc. 250m but n exc 500 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 117 | Returning, filling in, including spreading, levelling, watering and well ramming in layersnot exc 25 cm. |
| 118 | M&Lconcrete bed to drain pipes including packing under, and completely surrounding pipes with concrete after they are laid and tested in cement concrete 1:4:8, type D2 for 100mm bore pipe. |
| 119 | M&Lconcrete bed to drain pipes including packing under, and completely surrounding pipes with concrete after they are laid and tested in cement concrete 1:4:8, type D2 for 150 mm bore pipe. |
| 120 | S & FCI HublessPipes 100 mm bore single socketed in any lengthincl necessary fittings reqd in trenches or in floors incl demolition and breaking up existing drain pipes ( Salt glazed ware, AC or Reinforced concrete)complete all as specified and directed |
| 121 | M/L for 150 mm bore salt-glazed stoneware drain pipes laid in trenches and jointed as specified and directed. |
| 122 | M&L Brickwork with subclass‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 incl demolition of existing complete all as specified and directed. Note :- All the unhygienic bricks obtained from demolition to be thrown away out of MoD Land. |
| 123 | M&L Brickwork with subclass‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed. |
| 124 | M&L plain cement concrete type B1 1:2:4 (20mm graded aggregate) as in benching,copings etc, includingnecessary form work and complete all as spd and directed. |
| 125 | M&L PCC type D2, 1:3:6(40mm graded aggregate) as in foundation, filling andmass concreteincl demolitiom of existing all as specified and directed. |
| 126 | M&L for 15 mm thick rendering in CM 1:4 on brick or concrete surfaces and finished even and smooth without using extra cement, including providing and making necessaryarrengments for scaffolding all as specified and directed. |
| 127 | M&L for 15 mm thick rendering in CM 1:4 on brick or concrete surfaces and finished even and smooth without using extra cement,including taking down existing cement plaster and providing and making necessaryarrangments for scaffolding all as specified and directed. |
| 128 | M&L for75 mm thick Plain Cement concretePCC 1:4:8 type D-2(using 40 mm graded crushed stone aggregate) in sub base of flooring. |
| 129 | Labour only for coloured machine pressed rubber moulded precast concrete interlocking (red/yellow) paver block any shape and size complete incl demolition of existing paver blocks all as specified and directed. |
| 130 | Demolition of Cement Concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified. |
| 131 | Items for Yogender Vihar works |
| 132 | M&L for Providing factory made cover full floor mediun duty weightSquare/rectangular (size 600mm x 600mm) thickness not less than 75mm set in CM 1:6, as in cover slabs (for manhole, drainsetc) with plain fair faces, with angle iron frame alround all as spd. |
| 133 | M&L for Providing factory made cover full floor mediun duty weightSquare/rectangular (size 300mm x 450mm) thickness not less than 75mm set in CM 1:6, as in cover slabs (for manhole, drainsetc) with plain fair faces, with angle iron frame alround all as spd. |
| 134 | M & L for 75 mm thick PCC 1:3:6 type C-2 including demolition (using 20 mm graded stone aggregate) as in sub base of flooring complete all as specified and directed |
| 135 | Repair to Machine pressed precast concrete interlocking paver block including dismantling and refixing any shape, colour and size of 60mm thickness, M-35 Grade PU coated as specified and directed. |
| 136 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including necessary excavation making drainage opening wherever required complete. |
| 137 | Preparation of old/new surface of concrete/kerb stone surfaces, facias, cornices etc by removing all scale, loose material dust etc and applying two coats of weather proof anti fungal (Apex) paint over one coat of Birla/JK wall care putty to achieve surface smooth and applied as per manufacturers instruction complete specified and directed. |
| 138 | M & L for preparation of new plastered surface of walls and applying one coat Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. and directed |
| 139 | M & L for preparation of old plastered or unplastered surface of walls and applying two coat of white wash on walls complete all as specified and directed. |
| 140 | M & L for preparation of old plastered ceiling surface and applying two coats ofwhite wash completeall as specified and directed. |
| 141 | M & L forapplying minimum 1mm thick wall care water proofingputty over prepared surface to achieve the surface even and smooth for painting complete all as specified and directed. |
| 142 | S&F GI tank nipple, GI union, GI Socket 20mm bore including cutting into existing GI pipe complete all as specified and directed |
| 143 | S&F GI nipple, GI Socket 15 mm bore including cutting into existing GI pipe complete all as specified and directed |
| 144 | S&F GI reducer 15 to 20 mm bore complete all as specified and directed. |
| 145 | M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick walls all as specified and directed. |
| 146 | S & F in repairfor CP bib taps 15mm fancy type Chromium Plated quater turn cast copper alloy with crutch or butterfly handle complete all as specified. |
| 147 | S&F in repair Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm-125gms) complete all as specified and directed. |
| 148 | S & F in repair 15 mm bore Angle valves quarter turn, cast copper alloy, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed to GI pipe complete all as specified and directed. |
| 149 | S&F in repair 20 mm bore gun metal gate valve with iron wheel head screwed both ends for iron pipe including testing complete all as specified and directed. |
| 150 | S & F in repair wall mixer L-bend type with connecting legs and wall flanges, fancy typebrass chromium plated, with closted swinging spout including plugging and securing to walls suitable for 15 mm bore pipe, all complete as per the direction of Engineer-in-Charge. |
| 151 | S & F in repairBrass spindle for mixer/wall mixer of any type or pattern complete all as specified and directed. |
| 152 | S & F in repair central hole wash hand basin mixer,fancy type,brass chromium plated, with round spout with waste system , including plugging and fixed, suitable of 15 mm bore pipe all complete as per the direction of Engineer-in-Charge. |
| 153 | S & F in repair sink mixer,fancy type,brass chromium plated, swan neck type, including plugging and fixed, suitable of 15 mm bore pipe all complete as per the direction of Engineer-in-Charge. |
| 154 | S & F in repairs 15mm bore, fancy type shower rose, chromium plated complete all as specified and directed. |
| 155 | S & F in repairs hand shower (health faucet), superior quality, round shape, single flow, brass chromium plated, with 1m long flexible pipe with wall hook bracket etc. and all fittings for EWC complete all as specified and directed. |
| 156 | S&F in repair PVC double action Syphon kit with complete fittings for flushing cistern complete all as specified and directed. |
| 157 | S & F in repairs Tubular Towel Rail 20mm dia. \"D\" type, 600mm long of CP fixed with and including Chromimum plated brass screws and wooden/plastic cleats. |
| 158 | S&F in repair kitchen sinkmade of stainless steel 1mm thickkitchen or laboratory with plugs, washers and wastes,including bedding in cement mortar on dwarf wall or including fixing cantilever brackets and connecting unions to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 159 | S & Fstainless steel Kitchen plate rack of overall minimum size 750 mm x 900 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.80 mm thick fixed with rawl plug and CP steel screws complete, all as directed. |
| 160 | S&F Nozzle connection pipes built with solid 304-grade stainless steel, suitable for mixer faucets with hot and cold water flow options complete all as specified and directed |
| 161 | S & F in PVC flexible waste Pipe, having size 31X32X850 mm for WHB /Sink all complete as per the direction of Engineer-in-Charge. |
| 162 | S&F in repair vitreous china Wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed. |
| 163 | S&F 02 nos wash basin fasteners 15 mm in length fixed to basin and wall complete all as specified and directed. |
| 164 | S&F in repair 32mm bore Brass chromium plated waste coupling for wash basin/sink etc with inlet and outlet screwed for pipe or connections including necessary packing union and cap and fixed complete all as specified and directed. |
| 165 | S&F in repair Vitreous China wash down water closet pan, pedestal pattern, white, with \"P\" or \"S\" trap, excluding flushing cistern and flush pipe, with plastic water closet seat cover, white closed pattern with flat bottom and cover, fixed with MS chromium plated hinging device including connection to drain pipe (or outgoing pipe) and to flushing pipe etc and making good to floor complete all as specified and directed. |
| 166 | Cleaning and removing all scale and dirt, etc, from tanks & from mouths of circulating pipes, etc exc 250and n exc 500 capacity in litres and write date of cleaning and due date of cleaning on OHT all complete as per the direction of Engineer-in-Charge. |
| 167 | S&F in repair 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed. |
| 168 | S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25gms) |
| 169 | S & FPVC Bends/Tee etc any radius 100 mm sizecomplete all as specified and directed. |
| 170 | M&L for premium quality joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm,in floors etc., set andjointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layerin cement mortar 1:6 and dismantling of existing tiles complete all as specified and directed. |
| 171 | M&F for Vitrified Ceramic tiles light shade 8-10 mm thick (square/ rectagular) polished,area of each tilesnot exceeding 0.36 sqm ,in floors and skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6including dismantling of existing tiles complete all as specified and directed by Engr-in-Charge. |
| 172 | Taking down anodised aluminium three track aluminium windowsexc 1 but n. exc 2 sqm and refixing in the same opening after repairing including necessary jointing cleats, Glazing clips, rubber packing, screws etc & with existing anodised aluminium snap beading, screws, aluminium anodised fittings such as hinges type B-21, 125 mm long of aluminium tower bolt fibre wheel rollers (slidings rollers)complete all as specified and directed. |
| 173 | M&L for Welding in repairs n.exc 2.5cm in length, thickness of metal to be welded n.exc 6mm complete all as specified and directed |
| 174 | Taking down shutters of any description n. exc 1 sqm each complete all as specified and directed. |
| 175 | Resecuring or easing and adjustingwithout taking down shutters of any discription exceeding 1 sqm but not exceeding 2 sqm |
| 176 | S & F 200mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 177 | S&F 300 mm long MS ordinary pattern door spring \"plate type\" including roller and roller plate complete all specified and directed. |
| 178 | S&F in repair 25mm dia stainless steel curtain rod (weight not less than 300 g/RM) superior quality with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed. |
| 179 | S& F 18-20 mm thick lead free factory made 100% solid WPC (wood polymer composite) sheet for cupboard / Kitchen cabinet shutters and frames having high natural fiber content 25 to 30% wood colour sheets with density not less than 650 kg/ cum and the weight of sheet of 1 sqm should be 11 kg (+/- 5%) manufactured by ISO 9001-2015 certified company. the sheet should be 100% water proof, termite proof, fire retardant, manufacured by single layer extrusion process with excellent screw holding capacity and shore D hardness. complete all as specified |
| 180 | S & F 75 mm size a, stainless steelHandlefixed with screws for kitchen cabinet & below platform. |
| 181 | Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick \"D\"Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyster paint of 12-16 microns thick and back coated with 5-7 microns thick alkyed backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48x25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade) 0.36 mm minimum dia of wire and average width of aperture 1.4 mm. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10 mm square guard bars with 6\"(152.4mm) pitch, complete for finished item of work including of all taxes, design as per direction of Engr-in-Charge. |
| 182 | S&F powder coating anodized aluminium glazed ventilator ,Half fixed type with frosted glass 4mm thick and half fixed glass louevers with aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,complete all as specified |
| 183 | M&l for washed stone grit plaster on exterior walls in two layers under layer 12 mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square meter, top layer 15 mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size) in panels with groove allaround as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete all as specified (payment for providing grooves shall be made separately) complete all as specified & directed. |
| 184 | M&L for forming groove of uniform size 20 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and directed. |
| 185 | Taking down carefully old unserviceble existing single core wiring copper/aluminium for taking credit of retrieved material and making good disturbed surfaces of walls, floors all as specified and directed. |
| 186 | M&L for point wiringwith (FRLS) PVCinsulated unsheathed multistranded copper conductor cable of size 1.5 sqmm nominal cross sectional area single core drawn into existing conduit, including GI concealed terminal switch boxes not less than 1.0 mm thick of reqd size factory made , 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.5 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete for the following:- |
| 187 | One light/Fan point controlled by one, one way 5 Amp, one switch. |
| 188 | One bell/ buzzer pointcontrolled by one bell push. |
| 189 | One 5 pin 5 Amp socket outlet point on same board. |
| 190 | All as per Item No 189 above but One 5 pin 5 Amp socket outlet point on an independent board. |
| 191 | All as per Item No 189 above but for one 6 pin 15/16 Amp socket outlet point on an independent board with cables of size 2.5 sqmm and one green colour earth cable of size 2.5 sqmm. |
| 192 | S&F Switch piano flush button single pole one way 6 Amp 240 volt complete. |
| 193 | S & F switch piano flush button single pole one way 15 Amp 240 volt complete. |
| 194 | S&F socket outlet flush type multipurpose 2 in1, 3 pin 5 and16 Amp, 230 volts complete. |
| 195 | S&F socket outlet flush type multipurpose 2 in1, 5 pin 6Amp, 230 volts complete. |
| 196 | S&F bell push single pole one way 5 Amp, 240 volt flushtype. |
| 197 | S&F fan regulator electronic,step up socket type,230 volt, 100/120 W and conection complete. |
| 198 | S&F ceiling rose polycabonete bodythree terminal complete. |
| 199 | S&F angle type holder insulated body with back plate. |
| 200 | S&F in replacement switch piano flush button single pole one way 6 Amp 240 volt complete. |
| 201 | S&F in replacement switch piano flush button single pole two way 6 Amp 240 volt complete. |
| 202 | S&F in replacement switch piano flush button single pole one way 16 Amps 240 volt complete. |
| 203 | S&F in replacement socket outlet flush type multipurpose 2 in1, 3 pin 6 and 16 Amp, 230 volts complete. |
| 204 | S&F in replacement socket outlet flush type 5 pin 6 Amps 240 volts complete. |
| 205 | S&F in replacement Switch socket combination 2 in 1, 3 Pin 6 A flush type complete. |
| 206 | S&F in replacement ceiling rose surface bakelitethree terminal complete. |
| 207 | S&F in replacement bell push single pole one way 5 Amp, 240 volt fueshtype. |
| 208 | S&F in replacement angle type holder insulated body with back plate suitable for batten fittings. |
| 209 | S&F in replacement fan regulator electronic step sockettype for ceiling fan fixed, in existing board and connecting as directed, after dismantling and removing unserviceable regulator complete. |
| 210 | S&F in replacement call bell AC single pole 240 volt ding dongType. |
| 211 | S&F in replacement wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 8/10 W, 6500 K, 230V , minimum 120 lumens/watt,with extruded aluminium housing & integrated electronic driver completeincluding Electrical connection with PVC three core copper flexible wire & all necessary fixing arrngementsall as specified. |
| 212 | S&F in replacement wall/surface mountingluminaires integrated LED Batten 16/20 W, 6500 K,120 lumens/watt , 230V with extruded Aluminium housing4 feet long with frosted PMMA/PC diffuser & integrated electronic driver, 25k burning hours, 2.5 KV surge protectioncomplete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangementsall asspecified. |
| 213 | S&F in replacement Decorative wall light fixturemade up of Metal base, synthetic white in colour and square/round metal base with bend pipe and glass globe with nickel finish,( B-22/E27 base), with 01 No. 7/9 W LED Bulb, 230 V, 6000K, complete incl all required electrical connecting arrangements allspecified . |
| 214 | S&F in replacement LED Building security light 20/25 Watt with high power LED source (>100 lumen/watt) PDC housing, IP66 and IK 07with 4 KV inbuilt surge protection ,minimum 50000 burning hours hv cutoff@325/440 volt protection for 8 hoursincluding Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories , as specified. |
| 215 | S&F in replacement LED lamp 9 watt, complete all as specified and as directed. |
| 216 | S & Fhighly durable built -in LI-IONLED bulb inverterrechargable type LED 15/18/20 watt lamp crystal whitefor battery backup up to 4 Hrs min 4 star rated6500Kand bulb comes with overcharge & deep discharge protection withcharge time 8-10 Hrs with overcharging protection to protect battery incl Li-ion rechargeable battery, 230 volt, incl low energy consumption and non dimmable high beam bulbs for better light spread & beam with No visible Flickering and a Glare reduction Technology.complete. |
| 217 | S&F in replacement FTL fittings with decorative LED batten made up of aluminium casting18/20 Wof size complete standard fittings and fixtures including fixing on walls/roofs/ through MS downrod suspended typewith fitting arrangement including neccessary elect connection from ceiling rose to luminaries with suitable size PVC cord complete. |
| 218 | S&F in replacement Material glass/ Fuiber poly carbonateled tube ,voltage range 220-240v-50hz ,cct 6500k,lumen ,wattage 16/20 W surge 2.5kv ,CRI 80 POWER FACTOR >_0.9 ,BURING HOURS 25K HOURS120 L/W ,6000 Kwith high efficency, with neccessary electrical connection incl disconnection old elecronic ballast if anycomplete. |
| 219 | S&F in replacement for 1.5 sqmm single core copper,multistandard PVC insulated (FRLS) unsheathed, cable 1100 volts grade complete. |
| 220 | S&F in replacement for 2.5 sqmm single core copper,multistandard PVC insulated (FRLS) unsheathed, cable 1100 volts grade complete. |
| 221 | S&F in replacement for 4.0sqmm single core copper,multistandard PVC insulated (FRLS) unsheathed, cable 1100 volts grade complete. |
| 222 | S&F in replacement three core PVC insulated FRLSH sheathed cable with 1.5 sqmm stranded copper conductor complete all as specified and as directed. |
| 223 | S&F in replacement PVC insulated PVC sheathed flexible round stranded copper wire of size 2.5 sqmm, 3 core complete. |
| 224 | S&F in replacement sheet metal enclosure for MCB DB double door type,IP-43, IK 09 single pole and neutral 12 way 240 Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. |
| 225 | S&F in replacement sheet metal enclosure for MCB DB double door type, IP-43, IK 09 single pole and neutral 4 way 240 Volts with 100 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete. |
| 226 | S&F in replacement MCB, single pole 06 to 32 Amp, 240 volts, 10 KA breaking capacity, \"C\" curve complete. |
| 227 | S&F in replacement MCB, single pole & neutral 32 Amp, 240 volts, 10 KA breaking capacity, \"C\" curve complete. |
| 228 | S&F in replacement MCB, TPN, 63Amp, 415 volts, 16 KA breaking capacity, \"C\" curve complete. |
| 229 | M&L for Sub main wiring with two single core PVC insulated cable with 4.0 sqmm nominal cross sectional area stranded copper conductor and one single core green PVC insulated 4.0 sqmm stranded copper conductor earth continuity cable drawn through non metallic rigid PVC conduit 20 mm dia including all conduit and fixing accessories concealed in wall including cutting chases in wall and making good disturbed surface to match of walls/ceiling complete.(Note - PVC Conduit and accessories shall be deemed to be included in the quoted rate) |
| 230 | S&F PVC casing and caping, 20 mm wide complete . |
| 231 | S&F in replacement PVC gang box fitted with2 in1, 3 pin 6 and 16 Amp switch socket combination, 230 Volts complete with pvc gitties and screws all as specified. |
| 232 | S&F in replacement rectangular laminatedsheet top cover for switch sockets of size\" (125mmx125mmx3mm) |
| 233 | Same as item 46 here in before but (200mmx125mmx3mm) |
| 234 | Same as item 46 here in before but(225mmx275mmx3mm) |
| 235 | Taking down and refixing and Comprehensive repair/maintenance of storage type electric water heater (geyser) of capacity 25/50 litres, vertical or horizontal type comprising of the following:(a) Opening or dismantling the storage tank, taking down, de-scaling, brushing and thoroughly cleaning.(b) checking of all stop cock, pressure release valves, fusible plugs for its serviceability etc. in situ to ensure proper functioning of parts including supply and replacing of washers/ gasket nut etc.(c)Checking and rectify earth continuity of the Electrical circuits of Geyser and power point.(d)Checking and re-fixing thermostat and re-adjust.(e) De-scaling the immersion type heating element and siphon assembly with diluted Hydrochloric acid or clear pedette solution.(f)Checking of indicator lamp for it proper serviceability. (g) Re-assembling the Geyser and re-install at same position and testing complete all as specified and directed.NOTE: Unserviceable Parts/ components of electric water heater shall be replaced by the contractor. (ii) Supply of new parts/components shall be measured and paid separately under respective item of schedule. |
| 236 | S&F in replacement thermostat of Type EST 11/20A, 240 Volt of ISI marked approved make complete. |
| 237 | S&F in replacement thermostat of Type EST 7/15A, 240 Volt of ISI marked approved make complete. |
| 238 | S&F in replacement heating element of capacity 1.5/2 KW, AC 240 volts, suitable for storage type electric water heater as per requirement (press type/ screw type/ triangular/ circular base or ceramic cartrige type), ISI marked complete. |
| 239 | S&F in replacement heating element of capacity 3.0 KW, AC 240 volts, suitable for solarwater heater as per requirement (press type/ screw type/ triangular/ circular base or ceramic cartrige type), ISI marked complete . |
| 240 | M&L for spray painting to 25/50 litres capacity geysers with one coat of synthetic enamel paint of approved tint includingpreparation of old steel surface and writing of serial/ MES no. with black colour synthetic enamel paint (height of letters not exc 2cm) including taking down of geyser and refixing in the same position after completion of painting work and making inlet/ outlet water connection and testing complete . |
| 241 | S&F in replacement copper syphon (door) assembly suitable for geyser of capacity 25/50 litres of any type as required complete with inlet and outlet and provision for thermostat pipe with drain pipes with drain plug, screws, studs, clamps for fixing heating elements etc. including gasket complete all as specified. |
| 242 | S&F in replacement polycorbonate/Metal 3-pin, 16 amps Plug top, white complete all as specified. |
| 243 | S&F in replacement indicating LED lamp, Neon type, 240 volt AC suitable for 25/50 ltrs capacity geysers complete. |
| 244 | S&F in replacement safety valve suitable for 25/50 litres capacity geyser complete all as specified. |
| 245 | S&F in replacement sheet metal enclosures, single pole with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 25 Amps complete. |
| 246 | M&L for tracing and arresting of leakage in storage tank of 25/50 ltrs capacity geyser by brazing and soldering at leakage point and testing on completion complete. |
| 247 | S&F in replacement 450 mm long steel hose connection with brass adopter nut suitable for 15mm bore pipe and suitable for hot water and Cold Water Supply and fixed complete. |
| 248 | S & F in replacement600mm long steel hose connection with brass adopter nut suitable for 15mm bore pipe and suitable for hot water and fixed complete. |
| 249 | S & Fin replacement 450mm long PVC connection with brass adopter nut suitable for 15mm bore pipe and fixed complete. |
| 250 | S & Fin replacement600mm long PVC connection with brass adopter nut suitable for 15mm bore pipe and fixed complete . |
| 251 | S&F in replacement non return valve of cast copper alloy suitable for 15 mm bore pipe and fixed complete. |
| 252 | Periodical servicing of ceiling fan/Exhaust fan of any size/sweep and make after disconnecting all electrical connection, detaching the blades, removing fan with blades to workshop, opening and cleaning of fan, segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan complete and testing and refixing the fan in same position including all electrical connection and provn of replacement of two nos split pins, one connection block, canopy and one rubber reel complete all as specified and as directed.NOTE: (i) Replacement of new spare parts with old unserviceable parts other than connector, split pins, connection block and rubber reel and shall be measured and paid separately under respective item of schedule. (ii) Labour cost for replacement of spare parts shall deemed to be inclusive in quoted rate. |
| 253 | S&F BLDC ceiling fan 1200 mm sweep with powder coated aluminium blades min air delivery220 m³ /min, power consumption 28 watt, star rating (BEE) 5 star, 350 RPMwith down roadas per site requirement along with connected accessories incl provn of connection with three core flexible copper cod of size 1.5 sqmm from ceiling rose to fan min 2 year product warranty and 05 year motor warrantycompleteand Taking down ceiling fan 1200/1400 mm sweep any typeand deposit to MESyard forfuther BERBoard. |
| 254 | S&F in replacement new metal bush made out of Gun metal/ Brass of same size suitable for ceiling fan, wall mounted fan and exhaust fan complete. |
| 255 | S&F in replacement roter shaft of ceiling fan, exhaust fan, wall fan of any capacity, make and type complete . |
| 256 | S&F in replacement ball bearings No. 6201 and 6202 suitable for fan complete. |
| 257 | S&F in replacement ball bearings No. 6203 and 6204 suitable for fan complete. |
| 258 | S&F in replacementcapacitor 1.5 Mfd, 230 Volts, 50Hz complete all as specified. |
| 259 | S&F in replacement capacitor 2.5 Mfd, 230 Volts, 50Hz complete all as specified. |
| 260 | M & L for Spray painting ceiling fan of any sweep any size complete all as specified. |
| 261 | M & L for Spray painting Exhaustfan of any sweep any size complete all as specified. |
| 262 | Supply & fixingbulk head light fitting made from cast aluminium body with heat resistance pressure die cast housing, IP-65 protection cover suitable for bulk head fitting integrated type 6.5 W LED,6000K , 105 lumens/watt including inbuilt electronic driver complete all as specified.Note for item No. 01 to 264 :- BOQ has been prepared by clubbing items for 02 jobs. There may be similar description/nature of items at more than one place. In case different rates are quoted for same work, lowest rate quoted for each item shall prevail and liable to be paid in bill. No claim shall be entertained at a later stage. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
