|
| 1 | Dismantling of AC sheet (Corrugated, Semi corrugated etc) as in roofs etc including ridges complete all as specified and directed. |
| 2 | Dismantling timber scantlings framed work 40 sq. cm and over in section, in any position complete all as specified and directed. |
| 3 | Dismantling timber scantlings framed work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in sectionin any position complete all as specified and directed. |
| 4 | S&F of Pre-painted galvalume aluminium zinc coating base corrugated steel sheets 0.50mm thick of any approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 5 | S&F of Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 7 | S&F rolled steel section as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and similar works conforming to grade Fe 410-w (Gde-E-250 quality A) complete,all as specified and directed. |
| 8 | Dismantling wall and ceiling board( fiber, plug, insulation, etc) or insulation boards/ slabs/ blankets, any thickness incl cover fillets. |
| 9 | M&L false ceiling with 4 mm thick E-board \"Make-Everest\" white prelaminated set embossed reinforced designer ceiling board of approved texure fixed with GI imposed grid frame work of size not more than 600 x 600 mm having 24 mm wide T- section, runner made of 0.33 mm GI sheet and angle made of 0.45 mm GI sheet, suspended with 2 mm dia GI wire complete all as specified and directed. |
| 10 | S&F Solid PVC Wall Lining consisting of 5mm thick Panel with wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed. |
| 11 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified |
| 12 | Taking down cementplaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing downwith water, etc. any description . |
| 13 | M&L for Self Curing Ready Mix Plaster of thickness 12 mm to 15 mm, pre-packaged, ready-to-use formulated with cement, graded sand, polymers, and special self-curing compounds on external surfaces of walls, chajja, facia at any height with necessary scafolding surface finished even and smooth including taking down cement or cement lime plaster, raking out joints and preparing for plastering the wall surface with white cement based polymer modified including disposal of rubbish, all complete as per the direction ofEngineer-in-Charge. |
| 14 | M&L for Self Curing Ready Mix Plaster of thickness 10 mm to 15 mm, pre-packaged, ready-to-use formulated with cement, graded sand, polymers, and special self-curing compounds on Internal surfaces of walls, chajja, facia at any height with necessary scafolding surface finished even and smooth including taking down cement or cement lime plaster, raking out joints and preparing for plastering the wall surface with white cement based polymer modified including disposal of rubbish, all complete as per the direction ofEngineer-in-Charge. |
| 15 | Dismantling floor,hearth or wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. |
| 16 | M & L glazed ceramic joint free coloured tiles in vertical surfaces 600x300x7mmthick, set and joiunted in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in cement mortar 1:4. |
| 17 | M & L coloured Non Skid ceramic jointless tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n. Exc. 0.18 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer with CM 1:6 complete all as specified and directed. |
| 18 | M&L forVirified Ceramic tiles Dark shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed. |
| 19 | All as per description of serial item No 18 above but onvertical surface over & including 10mm thick screed bed in CM 1:4 complete all asspeciified |
| 20 | Demolition of brick work built in cement mortar or cement lime mortar including all of quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articlescomplete all as specified. |
| 21 | M&L brick work with old size fly ash bricks, straight or curved on plan exc 6M mean radius, modular brick built in cement mortar 1:6 complete all as specified and as directed. |
| 22 | Ditto all as item No 21 above but except bricks (using bricks recd in demolition) |
| 23 | M&L for brick work with old size fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4, complete all as specified and directed. |
| 24 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed |
| 25 | M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chhajjas, cover slab, shelves and similar articles set in CM 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately |
| 26 | M&L RCC type B-1 (1:2:4) using 20mm graded aggregate in slab supported on wall walls beams and columns in floors roof landings complete all as specified and directed. |
| 27 | M&L for TMT bars 10mm dia and overcut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 28 | M&L TMT bars of 6 to 8mm dia and over cut to lenth, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. |
| 29 | M&L form work for flat fair finished surfaces of concrete to soffits of suspended slabs such as roof slab not exceeding 200mm thick complete all as specified and directed. |
| 30 | Demolition of PCC as in ground floors & pavings not exc. 15 cm thickness (below or above G.L.) complete,all as specified and directed. |
| 31 | M&L for 75 mm thick PCC 1:3:6, type C2 using 40mm graded crushed stone aggregae as in sub bases of floors, complete,all as specified & directed. |
| 32 | S&F chequered tiles of size 300x300 mm, rubber moulded coloured decorative designed cement concrete tiles 25 mm thick size of tiles as approvedset, jointed and pointed in neat cement slurry with grey cement and pigments in floor incl 15 mm thick screed bed with CM 1:4 incl taking down existing tiles complete all as specified and as directed |
| 33 | M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as inplinth protection surface finished fair and even & smooth without using extra cementcomplete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3). |
| 34 | Forming constructionjoints 30 mm deep x 10mm wide filled with sealing compound grade \"A.\" |
| 35 | M&L for 16-18 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like, over 20mm thick screed bed in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite, complete all as specified and directed. |
| 36 | Rounding to edges of stone slabs one edge, such as in steps, cooking plateform incl making hole for gas pipe and other similar situation complete all as directed. |
| 37 | M&L preparing new untreated surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer. |
| 38 | M&L preparing new steel or iron surfaces of any description,exc 10cm in width or girth and applying two coats of synthetic enamel Paint over a coat of red oxide primer. |
| 39 | M&L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint complete. |
| 40 | M&L for preparation and applying two coats of oil bound distemper over a coat of primer over a coat of 1 mm thick puttyon newly plastered surfaces of walls complete all as specified. |
| 41 | M&L for preparation of newly plastered surfaces of walls and applying white putty of min 1 mm thicknessto prepare the surface even and smooth and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as speciifed. Note:- Paint to be applied with airless spray machine . |
| 42 | M&L for complete removal of exisiting finish (with mechanical sander machine) on walls and applying white putty of min 1 mm thicknessto prepare the surface even and smooth and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as speciifed. Note:- Paint to be applied with airless spray machine . |
| 43 | Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or mechanical means, including filling depression of scrapped surfaces with putty and applying two coats of oil bound distemper over a coat of 1 mm thick putty complete all as specified and as directed. |
| 44 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each. |
| 45 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each. |
| 46 | S&F Pressed steel frames size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. incl filling cement concrete type B-1 (1:3:6) filling and compaction in frame complete, all as specified, |
| 47 | M&L for 35 mm thick flush shutters, solid core construction, with block board 3 core and plywood face panels, commercial type on both sides complete. |
| 48 | M&L second class hardwood glazed and skeleton door shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; and fitted to chowkats. |
| 49 | S&F aluminium anodized door with frame of size 100X44.5X 1.5mm, stile, middle and top rails of size 82X44.5X1.5mm thick and bottom rail of size 114X44.5X1.5mm thick including 5.5mm thick tinted glass panes/5 mm thick ACP sheet, with all fittings/ fixtures such as cleats, tower bolt, hinges, locking arrangement, pull and push handle of aluminium anodized, hydraulic door closer etc., complete including aluminium and rubber beading all as specified and directed. |
| 50 | S& F of windows / Vintelator made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick \"D\"Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyster paint of 12-16 microns thick and back coated with 5-7 microns thick alkyed backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52x25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10 mm square guard bars with 6\"(152.4mm) pitch, complete for finished item of work including of all taxes. |
| 51 | S&F of Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules ofelasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. |
| 52 | S & F of Factory made single extruded WPC (Wood PolymerComposite) solid plain/ decorative flush door shutter of 30mm sizecomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessaryS S screws shall be paid separately) |
| 53 | S&F framed work such as grills, gratings etc with ends of bars shouldered and or reiverted or forged into spikes, framed guard bars and similar work conferming to Fe- 290-0 Gde-E-165 |
| 54 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanised wire staples complete. |
| 55 | S&F in repairskitchen PVC cabinet in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet consisting of carcass 18mm thick pvc sheet & provision of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets 5.5screws etc.The panels shall be fabricated using adhesive and screws where ever required.All the edgesshall be covered with 2mm thick edge bonding tape or 90 degree edge bent finishincl all necessary fitting as per site requitment as per make and specification mentioned as per drawing and all are specified and directed by Engineer-in-charge on site. |
| 56 | S&F magnet ball catcher for cup board shutters. |
| 57 | S&F Hasp and staple, 100 mm stainless steel, fancy type, including bolt to hinge plate and fixed with screws |
| 58 | S&F stainless steel handle, fancy type 150mm length with smooth finish matching the requirment of relevant is code as approved by engr-in-charge complete all as specified and directed. |
| 59 | S&F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified and directed. |
| 60 | M&L mild steel 300mm ordinary rat tail rod patttern springs includding roller and roller plate complete. |
| 61 | S&F Aluminium anodised barrel tower bolts of extruded section 200mm long complete, |
| 62 | S&F Aluminium handles cast type anodised of 150mm complete. |
| 63 | M&L for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed. |
| 64 | S & F, 100mm size butt hinges,stainless steel, and fixed all as specified and directed. |
| 65 | S&F 100 mm size Floor door stopper of aluminium alloy body and tongue, anodised, with rubber ends complete all as specified. |
| 66 | S & F in repair vitreous china wash down water closet pan (pedestal pattern) white (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti syphonage pipe etc complete all as specified and as directed. |
| 67 | S&F of Plastic water closet seat, black, closed pattern withflat bottom, and cover and mild steel chromiumplated or aluminised hinging device |
| 68 | S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including32 mm dia PVC flush pipeconnected to water closet with inlet, ball valve, float and handle complete,all as specified and directed. |
| 69 | S&F in repairs vitreous China wash basin white (flat back or angle back ) type of size 550mmx400 mm including brackets,brass cromium plated waste fittings and pvc waste pipe including cutting for and pinning in ends of bracket fixed complete all as specified. |
| 70 | S&F Vitreous China urinals, half stall type (flat back), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed |
| 71 | S & F repair 600mm x 45mm looking mirror, bevelled edge, of selected quality glass, mounted on 6mm th AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 72 | S&F in repair of15mm bore CP bib tap fancy type long body pattern with flange/cap cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipes complete all as specified. |
| 73 | S & Fin repair 15mm bore CP pillar tap,fancy type , castcopper alloy, with capstan heads, chromium plated, screwed down, high pressure fancy type with long shanks and fly nuts, screwed for iron pipe . |
| 74 | S & F in repair 15mm bore stop cock /angle cock fancy type , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes. |
| 75 | S & F in repair PVC connections, 450mm long with brass CP/PTMT nuts suitable for connecting 15mm bore pipes, superior quality. |
| 76 | S&F in repair 20 to 25mm bore chromium platedtype curtain rod withfixingbrackerts, stops, rollers etc complete allied fitting. |
| 77 | S & F repair tubular towel rail, brass chromium plated 20 mm dia ,D type,60 cm long between flanges complete all as specified and directed at site. |
| 78 | S&F sheet glass shelf assembley consisting of 5.5 mm thick sheet glass shelf 12cm wide with cromium plated bracket guard and railing 60cm long complete. |
| 79 | S&F glass corner self assembly, fancy type,made of 6 to 7mm thick sheet toughened glass of size 250x250mm,fixed with CP brackets,complete,all as specified and directed. |
| 80 | Demolition and breaking up drain pipes 100 mm bore (Salt glazed ware, AC or Reinforced concrete) set in cement mortar. |
| 81 | S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 82 | S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 83 | S & F infor 110mm PVC (SWR) WC connector bent type, completeall as specified and directed. |
| 84 | S & F in repair PVC (SWR) floor trap of size 110/110mm, completeall as specified and directed. |
| 85 | S&F for 75 mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement |
| 86 | S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 87 | S&F 75 mm bore PVC (SWR) bends any radius |
| 88 | S&F 110 mm bore PVC (SWR) bends any radius |
| 89 | S&F 15mm dia tubes medium grade galvanised, with all fitting and fixed complete to walls/ ceilings/ concealed or laid in floors including taking up or down existing steel tubing and connectionsall as specified and directed |
| 90 | S&F 20 mm Tubesmedium grade galvanised with all fitting and fixed complete to walls/ ceiling / concealed or laid in floors including taking up or down existing steel tubing and connections complete all as specified and directed |
| 91 | S&F, 500 Ltr capacity Rotational moulded polyethylene water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of existing tank and incl 20 mm PTMT float valve, high pressure with Polythene floot and flynutall as specified and directed |
| 92 | S&F1000 Ltr capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed including dismantling of existing tank and incl 20 mm PTMT float valve, high pressure with Polythene floot and flynutall as specified and directed |
| 93 | S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe of 20mm dia and fixed (minimum weight 210 gms) |
| 94 | S & F in repair gun metal gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of 20mm dia all as specified and directed. |
| 95 | M&L for 75 mm thick PCC 1:3:6, type C2 using 40mm graded crushed stone aggregate as in sub bases of floors, complete,all as specified & directed. |
| 96 | M&L for Machine cut kota stone slab flooring 18-20 mm thick over cement screed base of 20 mm thick in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and dismantling of old kota stone complete all as specified and as directed. |
| 97 | S&F sink made of stainless steel 0.8mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 600mm x 460 mm with bowl size 590mm x 430mm x160 mm including 40mm bore PVC waste fitting suitable for sink with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink. |
| 98 | M&L for heavy duty exterior vitrified tiles of size 300 x300x10mm laid over 15 mm thick screed bed in CM 1:6 jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tile complete all as specified and directed |
| 99 | M&L for cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations filling, sub base and mass concrete filling, etc complete all as specified and directed. |
| 100 | M&L for cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channel and drain complete all as specified. |
| 101 | M&L for plastering 15 mm thick in CM 1:4 on fair faces ofbrick or concrete surfaces, finished the surface even and fair without using extra cement complete all as specified and directed. |
| 102 | M&L forPCC 1:2:4 type B-1 using 20 mm graded stone aggregate as incopings, bed plates, plinth courses, parapets and the like including weathering, slightly rounded or chamfered angles and throatingincluding use and waste ofnecessary form work etc complete all as specified. |
| 103 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms,moulds, mitred / stopped ends etc complete all as specified and directed. |
| 104 | Add or deduct for 25mm inner girth or part thereof over or under 30cm and ditto complete all as specified and directed. |
| 105 | Taking down carefully aluminium point wiringwith PVCcasing capin and conduit (light, fan, socket or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets as required. |
| 106 | M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm ( Phase,- Red , neutral- Black)and earth continuity conductor 1.5 sqmm (green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia, ISI marked ivory colour with all conduit fittings / fixing accessories for the following :- |
| 107 | One light/ fan (CF & EF) point controlled by one switch. |
| 108 | One 5 pin socket outlet 6 Amps on independent board controlled by one switch. |
| 109 | One 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch. |
| 110 | M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm ( Phase,- Red , neutral- Black) and earth continuity conductor 2.5 sqmm(green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25 mm diaISI marked ivory colour with all conduit fittings / fixing accessories for 3 pin 16 amps socket outlet point controlled by one switch. |
| 111 | S&FSwitch Modular 6A single pole, one way, 1 module complete . |
| 112 | S&FSwitch Modular 16A single pole, one way, 1 module complete . |
| 113 | S&F Socket, 6A - 2/3 pin combined 2 module complete . |
| 114 | S&FSocket 6A/16A - 2/3 pin combined 2 module complete . |
| 115 | S&FModular White cover plate with frame,8 module complete . |
| 116 | S&FModular White cover plate with frame,4 module complete . |
| 117 | S&FModular White cover plate with frame,3 module complete . |
| 118 | S&F Modular White cover plate with frame,2 module complete . |
| 119 | S&F Modular Metal flush box 8 module complete. |
| 120 | S&F Modular Metal flush box 4 module complete . |
| 121 | S&FModular Metal flush box 3 module complete. |
| 122 | S&F Modular Metal flush box 2 module complete. |
| 123 | Renewal of LED surface mounted batten 20 watt, powder coated die cast/ extruded aluminium Body (Thickness ≥ 1.20 mm) or CRCA sheet ≥ 0.5mm and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50 Hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5%), life time (LEDelectrical circuitary), of minimum 50000 burning hours with 70% of initial Lumen maintained till life ends, CCT 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect including connections with suitable size FRLS, PVC insulated copper conductor cable and earthing etc as required with Minimum 5 year OEM warranty. System lumen efficacy 120 lm/Watt output. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as BIS shall be submitted. Note :- Heat Sink of aluminium housing such that LED junction temp shall not rise above 90 degree C. |
| 124 | Supply and fix ceiling rose, internal polycarbonate body complete. |
| 125 | Renewal of submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into andincluding concealed rigid non metallic PVC conduit 20 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes2x6 sqmm + 1x6 sqmm earth wire complete. |
| 126 | Renewal of submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into andincluding concealed rigid non metallic PVC conduit 20 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes2x4 sqmm + 1x4 sqmm earth wire complete. |
| 127 | Supply and fix in replacement of AC modular box with modular 20 Amp MCB SPN suitable for Geyser and AC complete with and including MCB, SP, AC, 240 volt of 20 Amp, \"C\" curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete. |
| 128 | Supply and fix in replacement of sheet metal enclosure distribution board, double door, single pole and neutral, AC, 240 volt, 12 way, with 100 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete. |
| 129 | Renewal of MCB distributionboard VTPN , 4 way, powder coated CRCA steel sheet suitable for MCCB incomer 125 Amp , 4 way 415 volt degree of protection IP 43 -Ik-09 with double door, recessed mounted having 250 amp insulated tinned copper bus bar , neutralbusbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate, in unused spaces wherever requiredcomprising of the following:- Incoming:-one number MCCB, 125 Amp, 04 pole, AC, 415 Volt, 50 Hz16 KA ( Icu=Ics), thermally adjustable between 70 % to 100 %.Outgoing:-Twelve numbers MCB, SP, AC, 240 volt, 50 Hz, 10 KA, 32 A, \"C\" series ISI marked. |
| 130 | Renewal of MCB, SP, AC, 240 volt of 06 to 32 Amp capacity \"C\" Series, ISI marked, incl making connections by using suitable copper lugsas required complete. |
| 131 | Renewal of MCB, DP, AC, 240 volt of 32 Amp capacity \"C\" Series, ISI marked, incl making connections by using suitable copper lugsas required complete. Note :- for MCCB\"s , MCB\"s, MCB DBs- MCCB\"s , MCB\"s, MCB DB\"s shall be of the same make. |
| 132 | Material and labour for earthingwith galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means oflug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipemedium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete. |
| 133 | Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard-II for BER procedure complete. |
| 134 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with remotecomplete |
| 135 | Supply and fixing in replacement LEDBldg security light fitting LED 45 watt with SPD, PF not less or equal0.9,epoxy coated cover sheet aluminium housing with heat resistant toughtened glass& IP 66 incl with bracket, clamps, nuts, bolts protection complete. |
| 136 | Supply & fix LEDCeiling /surface mounted down lighter, 2\"X2\" ,36W includingelectrical connection with PVC three core copper flexible wire & all necessary fixing accessories complete. |
| 137 | Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core complete. |
| 138 | Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes/cables etc getting out and bottom surface to required gradient complete. |
| 139 | M & L Returningfilling in including spreading leveling watering and well ramming in layers each not exceeding 25 cm thickness complete. |
| 140 | M & L Removal of surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete. |
| 141 | Supplying & Laying or Fixing DWC HDPE pipe alongwith all accessories like socket,bend,couples etc, ISI marked as per IS-16205(Part-24) including cutting/Jointing laid in trenches,wall,floor etc as required 63 mm outer dia and 50mm inner dia(for cable protection) complete. |
