|
| 1 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap forthermal expansion, 110 mm dia. (i) Single socketed pipes. 12.41.2 |
| 2 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement morter 1:2 (1 cemnt;2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindance E.C. 20% with 1% concentration. D.A.R No-2.35.3.1 |
| 3 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30mm thick including ISI marked Stainless Steel butt hinges with necessary (DSR -9.21.2) |
| 4 | Providing and fixing 8 mm dia C.P./S.S. jet with flexible tube upto 1 meter long with S.S. trangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in- charge. (17.16A). |
| 5 | Providing and fixing PVC low level flushing cistern with manually controlled device (handle lever) Conforming to IS : 7231 with all fittings and fixtures complete. (17.18). 10liter capacity -white (17.18.1) |
| 6 | Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white. D.S.R No- 17.19.1 |
| 7 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete. (17.28).semi rigid pipe 32mm dia (17.28.1.1) |
| 8 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality& make as approved by Engineer in charge. 15 mm nominal dia. Dsr 17.22b |
| 9 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid. D.S.R No- 17.20.1 |
| 10 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for hold fasts embedding hold fasts in cement concrete blocks of size 15x10x10 cm with cement concrete 1:3:6 ( 1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size). painting two coats of approved wood preservation to sides of chowkhats and making good the damages to wall and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge. Door chowkhats DAR No- 14.2.1 |
| 11 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. DSR No- 9.83 |
| 12 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours shades except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement 4 coarse sand) Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete. (DSR No- 11.38) |
| 13 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 ( 1 cement 4 coarse sand) (DSR No- 13.5.1) |
| 14 | Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete. 125x65x2.12 mm (DSR -9.55.1) |
| 15 | Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete 100x58x1.90 mm (DSR -9.55.2) |
| 16 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378). 300x16 mm (DSR -9.62.1) |
| 17 | Providing and fixing ISI marked oxidised M.S sliding door bolts with nuts and screws etc complete. 250x16 mm (DSR -9.62.2) |
| 18 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) 250x10 mm (DSR -9.63.1) |
| 19 | Providing and fixing ISI marked oxidised M.S Tower bolt black finish (Barrel type) with necessary screws etc complete (Copper oxidised as per IS 1378) 200x10 mm (DSR -9.63.2) |
| 20 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessaryscrews etc. complete (Copper oxidised as per IS 1378). 125 mm (DSR -9.66.1) |
| 21 | Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement trenching, refilling & testing of joints complete as per direction of Engineer-in-charge. External work. 25 mm nominal outer dia Pipes DSR No- 18.7.3 |
| 22 | Providing and fixing brass bib cock of approved quality ( 15 mm nominal bore)18.15.1 |
| 23 | Providing and fixing brass stop cock brass stop cock of approved quality ( 15mm nominal bore)18.16.1 |
| 24 | Providing and fixing ball valve (brass ) of approved quality , high or low pressure , with plastic floats complete:( 15 mm nominal bore)18.18.1 |
| 25 | Providing and fixing C.P. Brass bib cock of approved quality conforming to IS: 8931 15 mm nominal bore ( 18.49.1) |
| 26 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS stanDSRd and weighing not less than 810 gms , ( 15 mm nominal bore) 18.50.1 |
| 27 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. D.A.R No- 15.60 Please Enable Macros to View BoQ information |
