|
| 1 | M&L for boring under road manually with labour suitable for inserting 50 to 100 mm bore pipe at a depth 0.75 to 1.0 mtr complete. |
| 2 | M&L for cutting the existing hardstanding/PCC/WBM road/rocky surfaces at a depth of not less than 75 cm & 30 cm in width for passing of HT cables through GI pipes, returning filling in, complete incl finishing the surfaces by providing cement concrete type B1 (1:2:4) with 20 mm graded aggregate upto 20 cm, finishing to a uniform smooth surface complete all as specified and as directed. |
| 3 | Excavation in trenches by mechanical or other means n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe and getting out in hard dense soil old unsv Cables/Pipes incl connected items complete all as specified and as directed. NOTE for Item No 1 to 3: 1) The requirement of JCB (if any) for cutting the hard standing/PCC/WBM road surface or during earthwork is deemed to be included in the unit quoted rates. 2) If any damage to any Cable of Air Force/BSNL/MES etc. or to any Pipe lines develops/occurs during execution of the works then the same shall be made good by the Contr to the entire satisfaction of the concerned Dept/Section & the costs of the same is deemed to be included in the unit quoted rates.3) Quoted rate is also deemed to be inclusive of clearing/removing/cutting of vegetation/tree branches/small to medium plantings/bushes etc. so as to facilitate successful completion of the work. No extra/addl payment shall be allowed to the Contr in this regard.4) The contractor/firm is required to visit the site prior to quoting of the subject items/ work so as to ascertain the actual ground requirements. Any further query at a later date shall not be entertained & responsibility of the same shall rest on the contractor/ firm. |
| 4 | Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick. |
| 5 | Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point. |
| 6 | M&L for providing sand cushioning for protection of UG cable in trenches with dry (coarse) sand approved quality including filling, spreading and punning down to desired thickness complete. |
| 7 | Supply and laying sub class \"B\" bricks in trenches for protection of UG Cable complete. |
| 8 | M&L for GI pipe light grade with all running fittings (ISI Marked), fixed on Perimeter/Street light PCC poles etc. of bore 15 mm incl taking down old unsv one complete all as specified and directed. Make : TATA/JINDAL/PRAKASH. |
| 9 | M&L for GI pipe light grade with all running fittings (ISI Marked), laid in trenches, under road or fixing on wall/pole/crossing drain/nallah etc. of bore 50 mm complete all as specified and directed. Make : TATA/JINDAL/PRAKASH. |
| 10 | M&L for GI pipe light grade with all running fittings (ISI Marked), laid in trenches, under road or fixing on wall/pole/crossing drain/nallah etc. of bore 80 mm complete all as specified and directed. Make : TATA/JINDAL/PRAKASH. |
| 11 | M&L for GI pipe light grade with all running fittings (ISI Marked), laid in trenches, under road or fixing on wall/pole/crossing drain/nallah etc. of bore 100 mm complete all as specified and directed. Make : TATA/JINDAL/PRAKASH.IMPORTANT NOTE for Item Nos 8 to 11 : Wherever GI Protection pipes are to be placed/fitted above earths surface, cost of necessary clamping/fixing arrangements to the entire satisfaction of Engr-In-Charge is deemed to be included in the unit quoted rates. |
| 12 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 2.0 Core 10 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 13 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 4.0 Core 10 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 14 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 4.0 Core 16 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 15 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 4.0 Core 25 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 16 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 35 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 17 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 50 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 18 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 70 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 19 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 95 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 20 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 120 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 21 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 150 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 22 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 185 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 23 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 3.5 Core 240 Sqmm incl connecting with suitable glands, lugs etc. incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 24 | Supply, install, commissioning & testing of Straight Through Joint Kit (Heat Shrinkable Type) including jointing materials for making joints of UG electric cable 1100 Volts grade, heavy duty with PVC/XLPE insulated aluminium conductor nominal cross-sectional area 16 to 35 sqmm 3.5/4.0 core incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make : RAYCHEM/DENSON/M-SEAL/YAMUNA |
| 25 | Supply, install, commissioning & testing of Straight Through Joint Kit (Heat Shrinkable Type) including jointing materials for making joints of UG electric cable 1100 Volts grade, heavy duty with PVC/XLPE insulated aluminium conductor nominal cross-sectional area 50 to 70 sqmm 3.5/4.0 core incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make : RAYCHEM/DENSON/M-SEAL/YAMUNA |
| 26 | Supply, install, commissioning & testing of Straight Through Joint Kit (Heat Shrinkable Type) including jointing materials for making joints of UG electric cable 1100 Volts grade, heavy duty with PVC/XLPE insulated aluminium conductor nominal cross-sectional area 95 to 120 sqmm 3.5/4.0 core incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make : RAYCHEM/DENSON/M-SEAL/YAMUNA |
| 27 | Supply, install, commissioning & testing of Straight Through Joint Kit (Heat Shrinkable Type) including jointing materials for making joints of UG electric cable 1100 Volts grade, heavy duty with PVC/XLPE insulated aluminium conductor nominal cross-sectional area 150 to 300 sqmm 3.5/4.0 core incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make : RAYCHEM/DENSON/M-SEAL/YAMUNA |
| 28 | M&L for identification of Fault Location of LT UG Cable of size 3.5 core 50/95/120/150/185 Sqmm by removing both ends of the cable and locating the fault with HIPOT (HIGH POTENTIAL) Elect Cable Fault Locater of TGSPDCL or any other Govt Agency and arrangement of neccesary manpower for earthwork required at the fault area and rectifying the fault & making necessary electric connections with serviceable LT UG Cable etc. of appropriate size/grade incl connected items/works as per actual site requirement incl making good the disturbed surfaces complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge.IMPORTANT NOTE :1) Unit Quoted rates are deemed to be inclusive of the cost of any length of cable incl connected items/works like Jointing Kits etc. of appropriate grade/type/rating/capacity for jointing/successful completion of the Job.2) Cost of making good the disturbed surfaces is deemed to be included in the unit quoted rates.3) Cost of transportation of Manpower/Materials/Resources etc. to & from the complaint site is deemed to be included in the unit quoted rates.4) In the event of inability of identification of the fault location, Contr shall NOT be paid for the subject Job.5) Any item/job missed out in the item description/specification but technically required for successful completion of the work/job is deemed to be included in the unit quoted rates. |
| 29 | S&F Low Density Poly Ethylene (LDPE) flexible pipe of following dia and of pressure rating 6 Kg/cm² laid in trenches &/or inside the coping of poles for easy bending and passing of cables incl making good the disturbed surfaces complete all as specified and directed & to the entire satisfaction of the Engr-In-Charge. MAKE : POLYCAB/FINOLEX/SUPREME/PRINCE(a) 40 mm dia |
| 30 | (b) 25 mm dia |
| 31 | Supply, install, commissioning & testing of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 26 to 50 A incl spreader terminals & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge.. Cat No : DZ0F0032/0050CXC1AOOOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 32 | Supply, install, commissioning & testing of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 50 to 100 A incl spreader terminals & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Cat No : DZ0F0063/0100CXC1AOOOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 33 | Supply, install, commissioning & testing of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 100 to 125 A incl spreader terminals & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Cat No : DZ0F0125CXC1AOOOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 34 | Supply, install, commissioning & testing of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 36 KA & of rating 168 to 250 A incl spreader terminals & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Cat No : DZ4F0250DXD1AOOOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 35 | Supply, install, commissioning & testing of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 36 KA & of rating 268 to 400 A incl spreader terminals & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Cat No : DZ4F0400DXD1AOOOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 36 | Supply, install, commissioning & testing of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 36 KA & of rating 422 to 630 A incl spreader terminals & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Cat No : DZ4F0630DXD1AOOOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 37 | Supply, install, commissioning & testing of Manual Changeover Switch-Disconnector in Sheet Steel Enclosure conforming to IEC 60947-3, IS/IEC 60947-3, 415 V, AC 23A, 4P of rating 630A with & including Terminal Shrouds, Source Separator, Phase Barriers, Staggard Terminals perfectly suitable for Horizontal/Vertical Mounting & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Model/Type - CO4-630, Cat No : CO46300OSOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 38 | Supply, install, commissioning & testing of Manual Changeover Switch-Disconnector in Sheet Steel Enclosure conforming to IEC 60947-3, IS/IEC 60947-3, 415 V, AC 23A, 4P of rating 400A with & including Terminal Shrouds, Source Separator, Phase Barriers, Staggard Terminals perfectly suitable for Horizontal/Vertical Mounting & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Model/Type - CO4-400, Cat No : CO40000OSOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 39 | Supply, install, commissioning & testing of Manual Changeover Switch-Disconnector in Sheet Steel Enclosure conforming to IEC 60947-3, IS/IEC 60947-3, 415 V, AC 23A, 4P of rating 250A with & including Terminal Shrouds, Source Separator, Phase Barriers, Staggard Terminals perfectly suitable for Horizontal/Vertical Mounting & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Model/Type - CO3-250, Cat No : CO32500OSOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS. |
| 40 | Supply, install, commissioning & testing of Manual Changeover Switch-Disconnector in Sheet Steel Enclosure conforming to IEC 60947-3, IS/IEC 60947-3, 415 V, AC 23A, 4P of rating 160A with & including Terminal Shrouds, Source Separator, Phase Barriers, Staggard Terminals perfectly suitable for Horizontal/Vertical Mounting & making necessary electrical/cable connections complete all as specified and as directed & to the entire satisfaction of the Engineer-In-Charge. Model/Type - CO2-160, Cat No : CO21600OSOO of Make L&T or techno-commercially equivalent of ABB/LEGRAND/SIEMENS.IMPORTANT NOTES :1) Unit Quoted rates are deemed to be inclusive of the cost of any requirement of Spreader Links, Bus-Bar Modifications, Change/Replacement of Cable Lugs, Trimming of Cable Strands etc. complete all as specified & as directed & to the entire satisfaction of the Engr-In-Charge.2) Cost of making good the disturbed surfaces (if any) is deemed to be included in the unit quoted rates.3) Cost of transportation of Manpower/Materials/Resources etc. to & from the complaint site is deemed to be included in the unit quoted rates.4) Any item/job missed out in the item description/specification but technically required for successful completion of the work/job is deemed to be included in the unit quoted rates. |
| 41 | M&L for cement concrete in foundation, filling mass concrete type-C2, 1:3:6, (40mm graded aggregate) for pole/stay foundation etc. & finishing the surface even & smooth without using extra cement incl necessary formwork complete all as specified & as directed. |
| 42 | M&L for PCC (1:2:4) Type B-1 (using 20mm graded stone aggregate) for coping of poles etc & finishing the surface even & smooth without using extra cement incl necessary formwork complete all as specified & as directed. |
| 43 | Supply and fix energy saving high power LED Street light of 50W or higher rating made up of pressure die cast aluminum housing with embedded PC cover having top opening, seperate driver compartment with IP-65/66 protection, > 100 Lumen/Watt,> 80 CRI, 120\" Beam Angle, 6KV Surge Voltage Protection, SMD Light Source, PF > 0.95, THD < 5% with all accessories as per manufacturer instructions & fixing/fitting on existing GI pipe bracket with & including necessary fixing arrangements etc. and connecting up electrically from Junction box/OH Line to light ftg by means of 3 core 1.5 sqmm copper PVC round conductor incl taking down old unsv conventional light fittings complete all as specified and directed by Engr-in-Charge. Make: LUKER, Cat No : LSTE050S or techno-commercially equivalent in HAVELLS/BAJAJ/PHILIPS/JAGUAR |
| 44 | S & F loop in-loop out junction box of minimum internal dimension 140 x 140 x 95 mm or higher size made out of FRP sheet with weather proof canopy and locking screw comprising of 20 Amps rated 4 way connectors for 3 Phase and Neutral incoming/out going mounted in the box, fixing on RCC poles etc. with & including suitable sized Aluminium/MS clamps, cable glands, lugs, nuts, bolts etc. & fitted with 01 Nos MCB SP 10A, 10KA breaking capacity, C Series incl taking down/out old unsv one complete all as specified and as directed by Engr-in-Charge. Make of FRP Junction Box : Sintex/CAPE ELECTRIC/HENSEL or techno-commercially eqvt & Make of MCB SP : L&T/Legrand/ABB/SIEMENS.Note for Item Nos 42 & 43 : 1) Design/Drawing/Technical catalogue/specifications along with comparative Rate Analysis to be submitted to the Engr-In-Charge/GE for Make/Sample approval of items whereever equivalency of Item(s) is concerned other than specified Make/Model/Cat/Part Ref concerned before placing order to the Manufacturer/Supplier. 2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. 3) Make of Electronic Drivers shall be same as that of the LED fitting. 4) Cost of connectors/adapters of suitable size/type if required for proper fixing/connection of LED light fittings is deemed to be included in the unit quoted rates. |
| 45 | M&L for preparation of old painted surfaces of PCC/Steel Poles & applying two coats of weather coat paint of approved colour & grade (for PCC Poles) or applying two coats of Aluminium Paint over a coat of red oxide primer of approved colour & grade (for Steel Poles) incl writing of Pole Numbers & also painting of GI Pipe brackets & clamps with two coats of Aluminium Paint over a coat of red oxide primer complete all as specified & as directed by the Engr-In-Charge. |
| 46 | M&L for Re-Stringing and fixing in position of sagged ACSR conductor of required size of OH lines including binding with aluminium binding wire complete after removing and refixing of UG Cables/Service wires to the ACSR conductor complete all as specified and as directed by the Engr-in-charge. |
| 47 | M&L for aluminium conductor steel reinforced (ACSR) for jumpering & Stringing and fixing in position of required size/type for OH lines including binding with aluminium binding wires complete after removing the unsv conductors complete all as specified and as directed by the Engr-in-charge. |
| 48 | S&F PVC LT Line Separators 4 way with nuts & bolts arrangement in the existing OH lines on pole on height 7.0-8.0 Mtrs above GL incl taking down old unsv one complete all as specified and as directed by the Engr-In-Charge. |
| 49 | S&F cable three core PVC insulated, PVC sheathed, multi stranded aluminium conductor cable size 2.5 Sqmm for connection from Junction Box/OH Lines to Street/Security lights including taking down old unsv one complete all as specified and as directed. Make: Havells/Finolex/Polycab/Gloster |
| 50 | S&F GI Pipe bracket fabricated out of GI Pipe light grade 40 mm dia, 1.2 mtr long bent to shape as required at site and fixed with suitable sized MS clamps made out of 40 mm x 5 mm MS Flat, nuts, bolts, washers etc to poles/walls incl taking down old unsv one complete all as specified and as directed by the Engr-In-Charge. |
| 51 | M&L for steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31, 9.0 meter long, single swan neck type inclusive of one primer coat of red oxide zinc chrome primer and two coats of aluminium paint incl preparation of surfaces incl taking down old unsv one & making good the disturbed surfaces (if any) complete all as specified and as directed & to the entire satisfaction of Engr-In-Charge. The poles shall confirm to IS - 2713 & each component pipe shall be ISI Marked & confirm to IS - 1161. Make : India Electric Poles/Bombay Tubes/National Tubing Company/India Tube & Co. NOTE : 1) Necessary earthwork, PCC etc. shall be measured & paid separately under relevant items of work. |
| 52 | M&L for Prestressed Concrete poles 11.0 meter long 152mm x 152mm at top & 152mm x 260mm at bottom, Class 9 incl taking down old unsv one & making good the disturbed surfaces (if any) complete all as specified and as directed & to the entire satisfaction of Engr-In-Charge. NOTE : 1) Necessary earthwork, PCC etc. shall be measured & paid separately under relevant items of work. |
| 53 | M&L for cross arms bracings supports, clamps and back plates fabricated from structural steel sections incl nuts, bolts, washers welding, bending cold or hot, drilling holes for bolts in any shpae or size as indicated or directed and inclusive of one primer coat of red oxide zinc chrome primer and two coats of aluminium paint incl preparation of surfaces complete. |
| 54 | M&L for anti-climbing devices, comprising of 2.24 mm dia galvanised steel 2-strand barbed wire with 2.00 mm dia barbs wrapped spirally round poles, to a length of 0.5 mtr to 1.0 mtr clamped & properly secured or as specified & as directed (clamps measured separately). |
| 55 | S&F Pin type, porcelain, vitreous, white, brown or green insulator including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 100 mm height, 65mm dia for 1100 volts grade including dismantling of old unserviceable insulator complete all as specified and as directed by the Engr-In-Charge. Make : BHEL/PACTIL/JAIPURIA BROTHERS. |
| 56 | S&F Shackle Type Porcelain, vitreous, white, brown or green insulator including galvanised mild steel straps, washers, insulator bolts, washers and nuts 75 x 90mm for 1100 volts grade including dismantling of old unserviceable insulator complete all as specified and as directed by the Engr-In-Charge. Make : BHEL/PACTIL/JAIPURIA BROTHERS. |
| 57 | M&L for stay assembly complete with accessories as shown in Elect Plate No-1 of SSR Part -I 2009 for dia of stay rod 20 mm incl GI stay strand of size 7/3.15 mm (maximum length 11.00 mtr) to keep the pole in vertical position incl loop insulator including dismantling of old unserviceable insulator complete all as specified and as directed by the Engr-In-Charge. NOTE : PCC will be measured and paid separately. Make : BHEL/PACTIL/JAIPURIA BROTHERS.NOTE for Item Nos 44 to 56 : 1) Cost of use/hiring/rent including transportation of Aluminum Ladders/Scaffolding arrangements etc. required for successful execution of the complete work/Job is deemed to be included in the unit quoted rates. 2) Quoted rate is also deemed to be inclusive of all safety precautions/measures to be taken by the contractor for labour employed at the site. 3) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. |
| 58 | M&L for Bus-bar box made out of 3.15 mm thick CRCA sheet, front openable & of size as approved by the Engr-In-Charge with Aluminium Bus-bar Strips 200 mm long each & of current rating 100 Amp with & including suitable size/type/rating insulators, nut/bolts incl one number of MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting, suitable for isolation, having breaking capacity 25 KA & of rating 100 to 125 A incl spreader terminals as Incoming, MCB TPN 63A, 10 KA, \"C\" Series - 01 No, MCB TPN 06-32A, 10 KA, \"C\" Series - 02 Nos as Outgoings, terminating the existing incoming and outgoing cables and provision of necessary cable glands, lugs, taking down & removing the old/unsv/existing one, disconnecting the existing cable, uncoiling the loop etc. along with necessary earth work, painting with 2 coats of synthetic enamel paint over a coat of red oxide primer complete with 40 x 6 mm angle iron support of length not less than 0.5 m grouted on PCC platform incl proper fixing arrangements complete all as specified and as directed by the Engr-In-Charge.NOTE: 1) Design / drawing / BOM of the Panel Board incl all accessories showing the dimensions is to be obtained from the Manufacturer / Supplier & is to be got approved from the Engr-In-Charge & GE before placing final order to the manufacturer.2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates.3) Necessary PCC foundation/plinth shall be as per the recommendations of OEM & cost of the same is deemed to be included in the quoted rates. |
| 59 | S&F PVC Conduit Pipe of size 25 mm dia, Medium Grade, including necessary fixing arrangements to wall/pole/other surfaces such as PVC clamps/hooks as required on site complete all as specified and as directed by the Engr-In-Charge. MAKE : FINOLEX/POLYCAB/PRECISION/MODI |
| 60 | S&F Perforated Cable Tray, made out of 2.0 mm Galvanized Steel sheet, duly bend to required shape by sheet bending machine, including cover, made of 1.2 mm thick Plain Galvanized Steel sheet duly screwed with the cable tray and duly fixed on the wall / ceilings / other surfaces including suitable Galvanized Steel brackets, or hanging from the ceiling with suitable suspenders etc. as required at site incl taking down old unsv one complete all as specified and as directed by the Engr-In-Charge for the following sizes :a) 100mm (4 inch) width |
| 61 | b) 150mm (6 inch)width |
| 62 | c) 200mm (8 inch)width |
| 63 | d) 250mm (10 inch) width |
| 64 | M&L for disconnecting and taking out existing ACBs from housing/enclosures/panels etc. and Servicing of ACB 630A to1600A capacity, fixed type/ MDO/ EDO by cleaning, rubbing and overhauling the mechanical parts and making serviceability of Local/Remote electrical operations of the panel incl greasing Oiling , replacement of unsv Trip Coil, Breaker System, Gear Pinion, Roller Switch and re-assembling the same, checking of quality of Air Interrupter, insulation resistances, static contact resistances, Testing(IR value, Ratio test, Polarity test), connection testing and calibration of relays including all other functional tests of the ACB panel complete all as specified and as directed & to the entire satisfaction of the Engr-In-Charge. |
| 65 | M&L for repairing of panel boards of any size/type by removing of incomer/outgoing cables and connecting the same with same size of new lugs, nut, bolts & carrying out welding works for the damgaged / broken portions, making all doors freely operatable by applying grease and painting with two coats of synthetic enamel paint over one coat of red oxide primer for metal surface of panels surface area etc. complete all as specified and as directed & to the entire satisfaction of the Engr-In-Charge. |
| 66 | S&F Metal/fibre Sign Board of size 30x30 cm, 5mm thick, having colour coding as per relevant IS/IEC safety standards with red background having text written as \"MEN AT WORK - DO NOT SWITCH ON\" in english and suitable to be hung with chain or hook on the panel switch handle/breaker lever etc. incl taking down old unsv one complete all as specified and as directed & to the entire satisfaction of the Engr-In-Charge. Make : As per Sample/Existing. |
| 67 | S&F 3 Pole Power Contactor of AC3 duty & of rating 63 amps having 240 Volts rated No Volt Coil and having 2 NO (Normally open) + 2 NC (Normally closed) configuration incl taking down old unsv one complete all as specified and as directed by the Engr-In-Charge. |
| 68 | S&F Auxiliary Contact with 2 Nos 0.5 Module, 240 volts rated incl taking down old unsv one complete all as specified and as directed by the Engr-In-Charge. |
