Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Dismantling plain corrugated CGI/PGI sheet in roof covering incl redges complete all as specified and directed by Engineer-in-Charge |
| 2 | Supply and fixing 0.63mm thick galvanised, corrugated mild steel sheeting with two corrrugations side lap, fixed with coach screws and washers, in roofs, wall etc. with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge |
| 3 | Supply and fixing 0.63mm thick galvanised, plain mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed by Engineer-in-Charge |
| 4 | Material and labour for preparation of new steel and iron surfaces of any description over 10 Cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer over a coat of moderant solution to remove zinc coating in camoflaughed patterncomplete all as specified and directed by Engineer-in-Charge |
| 5 | Material and labour for preparation of old steel and iron surfaces of any description over 10 Cm width or girth not otherwise described and applying two coats of synthetic enamel paint in camoflaughed patterncomplete all as specified and directed by Engineer-in-Charge |
| 6 | Dismantling structural steel work of any description complete all as specified and directed by Engineer-in-Charge |
| 7 | Supply and fixing Fe 410-W(Gde E 250)quality A rolled mild steel in roof trusses (framed) trussed, purlins, crane gantries, rails and framing (beam, tee, angle, channel or flat sections) including distance pieaces cleats etc |
| 8 | Material and labour for preparation of new steel surfaces and applying two coats of synthetic enamal paint over one coat of red oxide primer complete. |
| 9 | Dismantling of wall or ceiling boards (fibre,pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets |
| 10 | Providing & fixing 4 mm thick false ceiling at all heights with GRS (semi perforated 12 mm thick micro tegular edged GRS false ceilling) false ceiling tile of size 595X595 mm of approved texture ,design and pattern having moisture content less then 2 %, humidity resistance of 99%,NRCO .50 to 0.75 as per IS 8225 :1987, Noncmbustiibleas per IS 476 (part 4)-1970 and light reflectance of 855 (minimum) to be laid in true horizontal level suspended on interlockingmetel T grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @120 gms per sqm including both side) comprising of main T runners of size 15X32 mm length 3000mm ,cross T of size 15X32 mm of length 600mm to fromgrid module of size 600mm X600mm suspended from Ceiling using galvanised mild steel items (galvanizing @ 80 gms per sqm) i e 50mm long ,8mm outer dia M-6 hanger rod upto 1000mm length and L shape level adjuster of size 85X25X2mm galvanised iron perimeter wall angle of size 24X24X0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plug at 450mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications ,drawing and as per direction of the Engr- in Charge. |
| 11 | Taking down chowkats or frames including shutter exc 1.50Sqm but nexc 4.00Sqm complete all as specified and directed by Engineer-in-Charge. |
| 12 | Supply and fixing Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cutand fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. and of approved quality with 6 mm thick figured glass and ss wire mesh of 0.36 mm nominal dia and average width of aperture 1.40 mm, complete all as specified and directed by Engineer-in-Charge.Note:- The rate shall also include making all damages/plasteringrepair, leveling and making good in plumb all the cills and jambs of opening before fixing windows and , shall deemed to have been included in the quoted rate and no extra shall be admitted at a laterdate in this respect. |
| 13 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Doortransmission gear made of mild sleel with multi point locking system with strikes,SS Hinges heavy dutyNote:- The rate shall also include making all damages/plasteringrepair, leveling and making good in plumb all the cills and jambs of opening before fixing ventelatorsand , shall deemed to have been included in the quoted rate and no extra shall be admitted at a laterdate in this respect. |
| 14 | Supply & fix sheet glass ordinary quality 5.5 mm thick exc 0.5 sqm in each pane Note :- All accessories pre wired with suitable size copper conductor cable and cable gland/lugs etc, proper arrangements for proper ventilation with provn of connecting earthing at both sides of panel board including making necessary arrangements for fixing all as required at site and directed by Engr-in-charge. |
| 15 | Supply and fixinggalvanised mild steel wire cloth nominal dia of wire 0.56mm and average width of aperture 1.00mm in wooden/steel frame Note :- All accessories pre wired with suitable size copper conductor cable and cable gland/lugs etc, proper arrangements for proper ventilation with provn of connecting earthing at both sides of panel board including making necessary arrangements for fixing all as required at site and directed by Engr-in-charge. |
| 16 | Demolition of brick work built in cement mortar including all quoins arches pillars etc. |
| 17 | Taking down cement plaster on brick wallincludingraking out joints hacking for key srcubbing down with water complete all as specified and directed by Engr-in-charge. |
| 18 | Material and labour brick work with sub class \"B\" bricks in cement mortar 1:6, straight or curved on plan exc 6 mtr nean radius, using old size bricks complete all as specified and directed by Engr-in-charge. |
| 19 | Material and labour for rendering 05 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specifiedand directed by Engineer-in-Charge. |
| 20 | Material and labour12mm thick rendering in cement mortar 1:6 on fair faces of brick work surace rendering is to be even and smooth with out using extra cenent complete all as specified and directed by Engr-in-charge. |
| 21 | Material and labour 5 mm thick cement plaster in cement mortar 1:3 on celings, surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. |
| 22 | Material and labour for preparation of new plastered surfaces and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/lit and UV resistance as perIS 15489:2004, Alkali and funggal resistance , dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applieed @0.90litre/10sqm over new surfaces |
| 23 | Material and labour for preparation of old plastered surfaces and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/lit and UV resistance as per IS 15489:2004, Alkali and funggal resistance , dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applieed @0.90litre/10sqm over new surfaces in camouflaged pattern complete all as specified and directed by Engr-in-charge. |
| 24 | Material and labour for Preparation of old decorated wall surfaces and applying two coats of Oil bound distemper onwalls over 3 mm thick wall care putty complete all as specified and directed by Engr-in-charge. |
| 25 | Material and labour for Preparation new surfaces of walls and applying two coats of oilemulsion distemper over a coat of 3 mm thick wall putty complete all as specified and directed by Engr-in-charge. |
| 26 | Material and labour for Preparation new surfaces of ceilings and applying two coats of oilemulsion distemper over a coat of primer complete all as specified and directed by Engr-in-charge. |
| 27 | Demolition of cement Concrete(unreinforced)in ground floors and pavings n exc 15 cm thickness (below or above ground level) or as in sunken complete all as specified and directed by Engr-in-charge. |
| 28 | Dismantling floor hearth wall tiling (but not backing) removing servicable tiles to store rubbish off the premisses complete all as specified and directed by Engr-in-charge. |
| 29 | Material and labour for hard core of guage n.exc 63mm, deposited spread and levelled in layers n. exc 15cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in-charge. |
| 30 | Material and labour for 100mm thick PCC(1:4:8) type D-2 using 40mm graded crushed stone aggregate) as in floors complete all as specified and directed by Engr-in-charge. |
| 31 | Material and labour for makrana marble work 18 to 20 mm thick (table rubbed and polished ) in steps ,jambs ,pillars ,windowcills ,cooking platforms and like in 15 mm thick cement mortar (1:4) including poitning in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of makrana type complete all as specified and directed by Engineer in charge. |
| 32 | Material and labour PCC 1:3:6, type C-2, 75mm thick as in plinth protection, Surface finished fair and smooth without using extra cement complete all as specified and directed by Engr-in-charge. |
| 33 | Material and labour for 40 mm thick PCC(1:2:4) type B-1 using 20mm graded crushed stone aggregate) as in floors( leveling course) complete all as specified and directed by Engr-in-charge. |
| 34 | Material and labour for 20mm thick granite black slab, machine cut, well polished, bedded in 15mm thick in cement mortar 1:4 as in cooking plaforms & like and jointed with grey cement slurry and pointed with white cement(1:2) using marble dust with admixtures of pigments to match the shade of granite stone including cutting and polishing etc complete all as specified and directed by Engr-in-charge. |
| 35 | Material and labour non skid ceramic colour tiles 7 to 8 mm thickjoint free edge cut(square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm(300mmx300mmx7 mmthick) set and jointed in neat cement slurry and pointed in colour cement to match as in floor including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engr-in-charge. |
| 36 | Material and labour glazed ceramic colour tiles 300mmx450mm/300mm x200mm x7mm thick set and jointed in neat cement slurry and pointed in coloured cement on vertical surfaces such as skirting/dado over cement mortar rendering/screding 10mm thick in cement mortar 1:4 complete all as specified and directed by Engr-in-charge. |
| 37 | Supply and fixing vitrified ceramic tiles light shade, 10 mm thick (square/rectangular) polished, area of each tiles notexc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cementto match including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engr-in-charge. |
| 38 | Material and labour Machine cut kota stone slab flooring 20-25mm thick over 20 mm cement screed base in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-charge. |
| 39 | Supply and fixing 5mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing all as specified by Engineer-in-charge |
| 40 | Supply and fixing solid PVC wall lining consisting of 5mm thick wood grain printedPVC sheet inclusive of solvant cement and fixing at site on PVC frame as per specification and drawing all as specified by Engineer-in-charge. |
| 41 | Supply and fixing vitreous chinaware wash hand basin white flat back size 550mm x 400mm excluding taps, waste chain and plug and porecelain stopper but incl bracket and cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engr-in-charge. |
| 42 | Supply and fixing vitreous china wash down water closet (Pedestel patern ) white incl fixing bolt, plastic water closet seat cover black/white closed pattern with flat bottom and cover and mild steel chromimum plated hinging device, fixedall as specified directed by Engr-in-Charge. |
| 43 | Supply and fixing Viterous china urinal flat back, size of 465x355x265mm white with grating and union for discharge p[ipe including flush pipe grating and waste pipe complete all as specified and directed by Engr-in-charge. |
| 44 | Supply and fixing Hot and coldmixer fancy typesingle ordoublelegged cast copper alloy screwed down high pressure with crutch or butterfly handlescrewed both ends iron pipe suitable for 15mm bore pipe fixed to wash hand basin complete all as specified and directed by Engr-in-charge. |
| 45 | Supply and fixing PVC connection, 60cm long, 15mm in size with PTMT nust and PVC washers at both ends cocomplete all as specified and directed by Engr-in-charge. |
| 46 | Supply and fixing 15mm Angle/stop/gate valves, fancy type chromium plated, screwed down, high pressure with crutch or butter fly handlescrewed at two right angles endsfor both iron pipe complete all as specified and directed by Engr-in-charge. |
| 47 | Supply and fixing stop/gate valve,15 mm cast copper alloy chromium plated fancy type with long shank & cup (concealed type) with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 15mm bore iron fixed complete all as specified and directed by Engr-in-charge. |
| 48 | Supply and fixing PVC white low level flushing cistem 10ltrs capacity with all fittings syphonic action push stype with inlet ball valve and float incl PVC flush pipe, ball valve, handle, MS bracket etc complete all as specified and directed by Engr-in-charge. |
| 49 | Supply and fixing brass chhromium plated tubular tower rail20mm dia , D type, 60cm longbetween flanges complete all as specified and directed by Engr-in-charge. |
| 50 | Supply and fixing for 600 mm X450 mmlooking mirror of any size 5.5mm thick with aluminium frame selected quality mounted on 6mm thickcommercial ply wood and fixed to woodenplugs with chromium plated brass screw and cup washer complete all as specified and directed by Engr-in-charge. |
| 51 | Supply and fixingMild steel chromium plated flushing jet for padestal pattern WC 1000mm long tube superior quality including flexible pipe and brass chromium plated nuts complete all as specified and directed by Engr-in-charge. |
| 52 | Taking down steel water tubing 15 mm and connections, etc. complete all as specified and directed by Engr-in-charge. |
| 53 | Taking down steel water tubing and connections 20mm,etc complete all as specified and directed by Engr-in-charge. |
| 54 | Supply and fixing medium grade steel water tubing, 15 mm bore galvanised (including taking down) with all fittings such as Union , Tank nipple with tank fittings and socket, elbow, nipple etc. and fixed complete to walls or laid in floors complete all as specified and directed by Engr-in-charge. |
| 55 | Supply and fixing medium grade steel water tubing, 20 mm bore galvanised (including taking down) with all fittings such as Union , Tank nipple with tank fittings and socket, elbow, nipple etc. and fixed complete to walls or layed in floors complete all as specified and directed by Engr-in-charge. |
| 56 | Cutting chases in brick wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engr-in-charge. |
| 57 | Dismantling water tanks of capacity n exc 500 ltrsand removing from the site complete all as specified and directed by Engr-in-charge. |
| 58 | Supply and fixing rotational moulded,minimum 3 layers HDPE water storage tank of 500 ltrs capacity(Cylindrical vertical with closed top)ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMTfloat valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and directed by Engr-in-charge. |
| 59 | Supply and fixing in Stainless Steel curtain rod of20 mm diawith Stainless Steel bracket including Cp globe at both ends for each door and window, rings and side caps for every one meter fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw including CP globe on both ends for each door and window opening complete all as specified and directed by Engr-in-charge. |
| 60 | Dismantling of cast iron work of any description complete all as specified and directed by Engr-in-charge. |
| 61 | Supply and fixing in repair PTMT grating doom 100 mm dia with cockroach trap fixed properly to the floor and sealed properly and finished with white cement complete all as specified and directed by Engr-in-charge. |
| 62 | Supply and fixing 110mm PVC cowl complete all as specified and directed by Engr-in-charge. |
| 63 | Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenchesor in floors complete all as specified and directed by Engr-in-charge. |
| 64 | Supply and fixing 110mm bore PVC (SWR), branch piece Single T complete all as specified and directed by Engr-in-charge. |
| 65 | Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed by Engr-in-charge. |
| 66 | Demolition and breaking up 200mm drain pipes (Salt glazedware, AC or reinforced cement concrtete set in cement mortar complete all as specified and directed by Engr-in-charge. |
| 67 | Material and labour for cement concrete(1:3:6)type C-2 to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm diabore of pipe complete all as specifiedand directed by Engineer-in-Charge. |
| 68 | Supply and fixing HDPE DWC ( double wall corrugated ) pipe confirming to IS-16098 of 152 & 180mm internal and external dia respectively. Presure rating SN-8 fixed with rubber seal and copler required with and including suitable bends 90/60/45 ddegree etc single Y junction complete as required fixed as per manufacture instruction ,laid in trenches for sewage lineall as specifiedand directed. Note- rates included for pipe,bends any size,type Y junctions copler/ adoptor etc required and net total length of pipe with fittings shall be measured for payment purpose complete all as specified and directed by Engr-in-charge. |
| 69 | Cement concrete in surface channels and drains in cement concrete 1:3:6 type C1 (20 mm graded crushed stone aggregate) finised even and smooth using extra cement complete all as specified and directed by Engr-in-charge. |
| 70 | Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface, work in hard dense soil complete all as specified and directed by Engr-in-charge. |
| 71 | Material and labour for PCC 1:4:8 Type D2 40mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge. |
| 72 | Material and labour for PCC 1:3:6 Type C1 20 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as spefcified and as directed by the Engineer-in-Charge. |
| 73 | Supply and fixing MS plates plain or chequered square cut or notched forming holes drilled or welded any thickness complete all as specified and directed by Engr-in-charge. |
| 74 | Material and labour for coloured chequered cement concrete tiles 22 to 25mm thick, set jointed and pointed in neat cement slurry in floors, with grey cement and pigment including screed bed or bedding layer of mortar 15mm thick in cement mortar (1:4) complete all as specified and as directed by the Engineer-in-Charge. |
| 75 | Material and labour for 100mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate),spike rolling to surfaces or making impressions of expandedmetal,whilst the concrete is green complete all as specified.as in floors complete all as specified and directed by Engr-in-charge. |
| 76 | Taking down old unserviceable/deteriorated batten/PVC conduit point wiring from existing place i.e.light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets, ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of paris and to match / finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash complete all as specified and directed by Engineer-in-Charge. |
| 77 | Taking down main switch/DB/ changeover/AC box of any capacity including fixing accessories of single/three phase complete all as specified and directed by Engineer-in-Charge. |
| 78 | Material and labour in replacement of concealed point wiring on wall and surface on ceiling/roof with necessary fixing arrangements withPVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes suitable for modular frame plate made out of MS sheet of thickness not less than 1.6 mm with earth dollyand with suitable modular frame plate ISI marked for fixing of switches / sockets, fan regulators, wall mountingfittings, door bell & bulkhead/telephone socket etcincluding PVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/Putti or distemper / colour wash with same existing colour surfaces complete all as specified and directed by Engineer-in-Charge for the following:-(a) One light, fan, bell point controlled by one switch. |
| 79 | (b) 5 Amp independent socket point controlled by one switch. |
| 80 | (c) One 5 Amp socket point controlled by one switch on same board. |
| 81 | All as per item No 80 here-in-before but for power point wiring with 2.5 SqmmPVC-FRLSH insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FRLSH insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead One light, fan, bell point controlled by one switch. |
| 82 | Material and labour in replacement of sub main wiring with two single core PVC-FRLSH insulated unsheathed multi stranded copper conductor cable of size 10.0 sqmm drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc laid in concealed position with 10.0 Sqmm PVC-FRLSH insulated unsheathed multi stranded copper conductor as a continuous earth wire including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of paris/Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge |
| 83 | All as per Sr No 82, but of size 1.5 sqmm complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply and fixing in replacement of Modular Switch 1 way, 5/6 Amps, 1 module (ISI marked) complete all as specified and as directed by Engineer-in-Charge. |
| 85 | Supply and fixing in replacement of modular switch 1 way, 16 Amps, 1 module (ISI marked) complete all as specified and as directed by Engineer-in-Charge. |
| 86 | Supply and fixing in replacement of modular socket, 5/6 Amps, multi pin (ISI marked) complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Supply and fixing in replacement of modular socket, 6/16 Amps, multi pin (ISI marked).complete all as specified and directed by Engr-in-Charge. |
| 88 | Supply and fixing in replacement ofmodular Bell push, 5/6 Amps, 1/2 module (ISI marked) complete all as specified and as directed by Engineer-in-Charge. |
| 89 | Supply and fixing in replacement ofDoor bell multi music type 230V, single pole,ISI Marked complete all as specified and directed by Engineer-in-Charge. |
| 90 | Supply and fixing in replacement ofCeiling rose, surface backlite, 65 x 20 mm three terminal ISI Marked complete all as specified and directed by Engineer-in-Charge. |
| 91 | Supply and fixing in replacement ofLamp holder insulatedbody with back plate suitable for angle / batten fittingISI Marked complete all as specified and directed by Engineer-in-Charge. |
| 92 | Material and labour for surface point wiring on wall and surface on ceiling/roof with necessary fixing arrangements withPVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dollyand bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mountingfittings, door bell & bulkhead/telephone socket etc with MS screw and cup washers including PVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing all as specified and directed by Engineer-in-Charge for the following:-(a) One light, fan, bell point controlled by one switch. |
| 93 | Material and labour for surface submain wiring with two single core PVC insulated flexible copper conductor cable of size 2 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 2 Sqmm as earth lead in & includingnon metallicPVC conduit medium grade with all conduit accessores as per specification all as required at site or directed by Engr-in-charge. |
| 94 | Material and labour for switch piano flush button single pole one way 5 amps 240 volts complete all as specified and directed by Engineer-in-Charge. |
| 95 | Supply and fixing LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. |
| 96 | Supply and fixing 1100 volts grade heavy duty cable PVC insulated Aluminium staranded conductor , served with inner sheathed PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 01 mtrs apart including 4mm suspention wire one twin core flate/cicular of size 6 sqmm x 2core complete all as specified and directed by Engineer-in-Charge. |
| 97 | Supply and fixing in replacement of Sheet metal enclosure VTPN MCCB DB 4way, 415 V (vertical type) Double door with bus bar double door type IP 43 - IK 09 as per IEC 61439-3 suitable for flush mounting complete with 250 A copper bus bar for each phase with 2 neutral and 2 earth bus bars with cable ties for cable management for DB\"s when MCBs & MCCB125 Amps (as incomer)to be used, fixed properly in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and directed by Engineer-in-Charge. |
| 98 | Supply and fixing in replacement ofMCCB 125 Amps, 3 Pole, 415V, 16 KA with thermal magnetic protection adjustable type with short circuit and overload protection complete all as specified and directed by Engr-in-charge. |
| 99 | Supply and fixing in replacement of Double door metallic sheet metal enclosure for DB when MCBs to be used SPN 12 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires complete all as specified and directed by Engineer-in-Charge. |
| 100 | Material and laboursheet metal enclosure MCB distribution board. Single pole & neutral 240volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link complete all as specified and directed by Engineer-in-Charge. |
| 101 | Material and laboursheet metal enclosure MCB distribution board. Single pole & neutral 240volts 2 way with IP-43 IK-09 protectioncomplete with appropriate size complete all as specified and directed by Engineer-in-Charge. |
| 102 | Supply and fixing in replacement MCB SP 240 volt 6 Amp to 32 amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed by Engineer-in-Charge. |
| 103 | All as per item srlitem No 102 but SP 40 Amps complete all as specified and directed by Engineer-in-Charge. |
| 104 | All as per item srlitem No 103 but SPN 16-40 Amps complete all as specified and directed by Engineer-in-Charge. |
| 105 | All as per item No 104 here-in-before but SPN 16-32 Amps complete all as specified and directed by Engineer-in-Charge. |
| 106 | Supply and fixing in replacement ofDecorative ultra slimlinear LED lighting fixtures with extruded polycorbonate environmental friendly energy saver LEDlight fitting 1x20 watt (4\"), 230 Volts, single tube mounting including LED Tube20Watt complete with electronic driver spring loaded rotory type lamp holder, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection with three core copper cable from ceiling rose to led light fitting complete all as specified and directed by Engineer-in-Charge. |
| 107 | Supply and fixing in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V ACd ecorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. |
| 108 | Supply and fixing in replacement ofLED Lamp 12 watt, 240 volts complete all as specified and directed by Engineer-in-Charge. |
| 109 | Supply and fixing in replacement ofrecess mounted LED panel, 36 watt ( 2\"x2\"), highly efficient suitable for celing complete with all fixing accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable all as specifiedand directed by Engr-in-Charge. |
| 110 | Supply and fixing building security light fitting new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07of 35 watt LED, 240 Volts inclbracket made out of GI pipe 25mm dia medium grade, 0.9 mtr long bent to shape with welded MS flat 25 x 6 mm for mounting of fitting & MS flat iron clamps made out of 25mmX 6mm thick FI nuts, bolts complete all as specified and directed by the Engr-in-charge. |
| 111 | Supply and fixing Gyser including installation and testing ofISI marked, energy efficient, water heater storage typemade of ultra-thick super cold rolled steel plates, incoloy glass-coated heating element offering superior heating performance, electrically operated, single phase, 50 Hz (BEE 5 star rating), complete of 25 Ltr capacity suitable to withstand 8 bar pressure with whirlflow technology and adjustable knob for convenient setting of temperature with and including supply and fixing, wire armoured 450 mm long, 15 mm dia brass coupler etc, flexible pipe suitable to withstand upto 100 degree celcius for hot and cold water, anchor fastner - 04 Nos of suitable size, 3 core PVC insulated, FRLSH multistranded copper conductor cable and plug top 15 Amps capacity complete in all respect all as specified and directed by Engr-in-Charge. |
| 112 | Supply and fixing heavy duty exhaust fan AC single phase 230/240 V of size 300 mm sweep 1400 RPMwith louver & shutterincluding connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and necessary grouting on wall complete and making good the wall surface after fixing of exhaust fan all as specified and directed by the Engr-in-charge. |
| 113 | Supply and fixing exhaust fan of size 250 mm sweep made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper windingincluding connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and necessary grouting on wall complete and making good the wall surface after fixing of exhaust fan all as specified and directed by the Engr-in-charge. Note : Old unserviceable Exhaust fan is to be deposited to MES store yard. |
| 114 | Material and labour Earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level ) withtop edge of earth plate not less than 1.5 Mtr below normal ground level connected to earth lead wire 4 mm as earth lead by means of bolts, nuts washers and check nutsof steel/GI duly protected with 20 mm bore light grade pipe upto main board , 20mm bore watering pipe light gradewith CI/MS funnel and wire mesh including excavation, earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoaldust and common salt as diirectred by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel withwire mesh complete and all as specified and as directed by Engr-in-charge. |
| 115 | Dismantling taking out carefully old/unserviceable UG cable any type any size from trenches/poles/ducts/LT panels after dismentling ends from OH conductors/MCCBs/joint boxes for relaying/refixing or carrying to store for Sch of Credit. |
| 116 | Supply, layingtesting and connecting 70 Sqmm 3.5 Core XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electrical cable with aluminium conductor, 1100 volts grade laid in trenches/ducts/wall or through pipe with suitable size of cable glands, crimping type cable lugs complete all as specified and directed by Engr-in-Charge. |
| 117 | Ditto as per Ser No 116, but of size 35 x 3.5 sqmm complete all as specified and directed by Engineer-in-Charge. |
| 118 | Material and labour for excavation in trenches in any type of soil, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, laying of cables and getting out complete all as specified & as directed by Engineer-in-charge. |
| 119 | Material and labour for returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm each layer complete all as specified and directed by Engineer-in-Charge. |
| 120 | Material and labour for removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge. |
| 121 | Material and labour for tubing GI light grade 50 mm bore laid in trenches, ducts, floor for protection of cable,fixed to wall or poles including fixing arrangement all as required and directed by Engineer-in-Charge. |
| 122 | Material and labour in replacement ofLED street light fitting 100 Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge. |
| 123 | Ditto as per Ser No 45, but of size 122 watt complete all as specified and directed by Engineer-in-Charge. |
| 124 | Fabrication, supply, installation and testingof LT feeder pillar box floor mounteddust/vermin proof outdoor type, powder coated of size 0.60x0.85x0.50 mtr factory fabricated , made out of MS sheet of thickness 3.15 mm mounted on angle iron legs made out of angle iron of size 40x40x6 mm within front & rear opening with locking arrangement , containing bus bar chamber to accommodate 3 phase & 1 neutral copper busbar of size 20x10mm drilled with suitables holes for fixing of cables and mounted on epoxy based insulator in horizontal position (stepped manner) in feeder pillar including necessary excavation and PCC work 1:2:4 complete all as specified and directed by Engr-in-charge. |
| 125 | Supply, fix and laying of DWC pipe of size 50/38 mm dia (outer dia) with coupler including passing the LT Cables of size 16-70 sqmm through the DWC pipe in trench/duct/on wall (with clamp) for protection of cable all as per direction of Engr-in-Charge. |
| 126 | Supply, fix and laying of DWC pipe of size 90/75 mm dia (outer dia) with coupler including passing the LT Cables of size 70-95 sqmm through the DWC pipe for protection of cable complete all as specified and directed by Engineer-in-Charge. |
| 127 | Febrication, Supply, installation and testing in replacementof LT cubical outdoor panel box (Feeder Pillar) of suitable size or as per site requirement, IP-52 protection class, CPRI approved,floor mounted dust/vermin prooffactory fabricated , made out of MS sheet of thickness 3.15 mmmounted on angle iron legs made out of angle iron of size 40x40x6mmwith front & rear opening with locking arrangement, powder coated, CRCA sheet containing bus bar chamber to accommodate 3 phase & 1 neutral copper busbar covered with R Y B and black PVC heat shrinkable sleeve, size 40 x 10 mm mounted on hygroscopic insulators in horizontal position (stepped manner) in upper part of panel, middle part of distribution panel provided with separate chambers for 01 No. incomming MCCB, 05 Nos for outgoing MCCBs connected to copper busbar of size 20 x 5 mm in bottom partfor cable connection in distribution panel including PCC foundation of panel complete all as specified and directed by Engineer-in-Charge to accomodate the following:-(a) MCCB 200 Amps 4P, 36 KA, 415 volts with S/C and O/L protection thermal magnetic release adjustable type as incomer - 01 No.(b) MCCB 125 Amps 3P, 25 KA, 415 volts with S/C and O/L protection thermal magnetic release adjustable type as O/G - 01 No.(c) MCCB 50 Amps 3P, 25 kA, 415 volt, with S/C and O/L protection thermal magnetic release adjustable type as O/G - 04 Nos(d) Digital Multifunction meter, 3 phase AC 415 volt, flush mounting 96x96 mm accuracy class 1.0, input voltage measurement range 50-520 VAC with suitable CT\"s capable of measuring V, A, F, PF, KW, KVA, kWh/kVAh, old energy, Load hours, CT secondary site selectable 1A/5A, CT/PT site programmable including all parameters - 01 No.(e) Set of LED phase indicator lamp (R,Y,B) - 01 set. Note :- All accessories pre wired with suitable size copper conductor cable and cable gland/lugs etc, proper arrangements for proper ventilation with provn of connecting earthing at both sides of panel board including making necessary arrangements for fixing all as required at site and directed by Engr-in-charge. |
| 128 | Material and labour Earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level ) withtop edge of earth plate not less than 1.5 Mtr below normal ground level connected to GI Strip of size 25x4 mm as earth lead by means of bolts, nuts washers and check nutsof steel/GI duly protected with 40 mm bore light grade pipe upto main board , 20mm bore watering pipe light gradewith CI/MS funnel and wire mesh including excavation, earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoaldust and common saltquantity as recommended by the manufacturer oras diirectred by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel withwire mesh complete and all as specified and as directed by Engr-in-charge. |
| 129 | Supply and fixing in replacement of Gun metal globe or gate valve iron wheel head, screwed both ends for iron pipe of bore of 20 mm and length as required on site or directed by engineer-in-charge. |
| 130 | Material and labour in replacement for construction of valve pit brick masonry internal size 600x600x600mm (from top of PCC to bottom of cover ) including excavation in any type of soil returning, filling in around foundation and removal of surplus soil to a distance not exceeding 50 mtr, PCC 1:4:8 type D2 in foundation brick work in cement mortar 1:6, 6mm thick plaster in cementmorter 1:4 to internal surface covered pit with MS sheet over 2 mm thick with locking arrangement, handle fixing arrangement and painting with aluminium paint two coats over a coat of red oxide primer all as per specified and as dircted by Engr-in-charge. |
| 131 | Supply and fixing in replacement of copper strip of size 20x3 mm complete with saddles/ insulators made out of PVC or fibre and fixing screws for roof conductor/down conductor including welding or brazing for joints all as required at site or asdirected by Engr-In-Charge. |
| 132 | Supply and fixing in replacement of air termination single pointed copper rod 12mm dia and 300mm long Note :- All accessories pre wired with suitable size copper conductor cable and cable gland/lugs etc, proper arrangements for proper ventilation with provn of connecting earthing at both sides of panel board including making necessary arrangements for fixing all as required at site and directed by Engr-in-charge. |
| 133 | Material and labour in replacement for test point terminal block made of gun metal or phosphorus bronze of size 75X75X6mm drilled and screwed including 03 Nos 8mm dia 25mm long hexagonal head screw complete all as specified and directed by Engr-in-charge. |
| 134 | Supply and fixing in replacement of GI tubing light grade25 mm dia, cut to size and bent to shape all as required at site including fixing arrangement with necessary clamps of required size at site and providing appropriate size of insulators to pipe from foundation of air termination rod complete all as specified and directed by Engr-in-charge. |
| 135 | Material and labour Earthing complete with copper earth plate electrode 600x600x3.15 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level ) withtop edge of earth plate not less than 1.5 Mtr below normal ground level connected to copper Strip of size 20x3 mm as earth lead by means of bolts, nuts washers and check nutsof steel/GI duly protected with 40 mm bore light grade pipe upto main board , 20mm bore watering pipe light gradewith CI/MS funnel and wire mesh including excavation, earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoaldust and common salt after mixing with BFC (Back Fill Compound) inadeqate quantity as recommended by the manufacturer oras diirectred by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel withwire mesh complete and all as specified and as directed by Engr-in-charge. |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
