|
| 1 | Design, Supply, installation, testing and commissioning of horizontal double skin PUF insulated recirculatory Air Handling Units (AHU)s in modular construction having thermal break profile suitable for clean room application complete with direct driven fan, electric motor, cooling coil, SS-304 eliminator, filters (pre & fine), mixing chamber and other associated accessories of following capacity as per tendertechnical specification. |
| 2 | a) Capacity: 42.5 TRb) Air Flow Rate : 25000 CFMc) St. Pressure: 150 mm of WC |
| 3 | a) Capacity: 50 TRb) Air Flow Rate : 30000 CFMc) St. Pressure: 150 mm of WC |
| 4 | Supply, fabrication, installation, testing and commissioning of GI ducting fabricated out of following thickness sheets. The GI ducting shall be complete with bends, elbows, reducers/transition pieces, MS or GI flanged joints, 6 mm thick neoprene gasket, GI hardware, leak proof joints etc in accordance with IS-277,IS-655, silicon sealant etc. as per drawings and as per tendertechnical specification. |
| 5 | 20G thick GI sheet ducting |
| 6 | 18 G thick GI sheet ducting |
| 7 | Insulation with 0.5mm thick cladding : Supply and installation of 19 mm thick closed cell class \"0\" zero nitrile rubber insulation complete with other accessories such as adhesive, jointing taps and covered with 0.5mm thick aluminium cladding as per tendertechnical specification. |
| 8 | Supply and installation of 19 mm thick closed cell class \"0\" zero nitrile rubber insulation with factory laminated aluminium foil complete with other accessories such as adhesive, jointing taps, etc. as per tendertechnical specification. |
| 9 | G.I. volume control damper - Supply, installation,testing of manually operated, multilouvered,opposed aerofoil blade G.I volume control damper with aluminum paint, outer body frame and blades fabricated out of extruded G.I section complete with other accessories such as locking arrangement, gear train, handle, position indicator etc. of 1.5mm (minimum) thickness. as per tendertechnical specification. |
| 10 | Supply and installation of combined motorised fire cum smoke control damper as per UL 555 and UL 555Scomplete with fire & smoke sensors, actuator, control panel and other accessories as per tendertechnical specifications. |
| 11 | Supply and installation of Sound Attenuator of length 1500 mm with GSS casing splitters, fibber glass tissue paper for covering with SS perforated sheet etc. suitable as pertechnical specification |
| 12 | Supply, Installation and testing of pre insulated aluminum class ‘O’ as per UL-723, Flexiable duct to withstand of min 6” w.g. pressure as per of technical specifications. |
| 13 | Supply and installation of grill with Volume control dampers :Type : Manually operated, multi-louvered, opposed blade type & AMCA Certified, Frame : Extruded aluminium section(minimum thickness 1.5mm), Blade : Aerofoil aluminium section minimum thickness 1.50mm. |
| 14 | Supply, installation and testing of GI powder coated terminal box of size 600 mm x600 mm of thickness 1.5 mm for HEPA filters as per technical specificationswith mini pleated H14 HEPA filters for clean room. The Filters shall be tested as per EN 1822 standards as per technical specifications. |
| 15 | Air curtain : Supply, Installation, testing and commissioning of air curtain, the body of air curtain shall be made with stainless steal 304 grade, with all accessories i.e. sensors, PCB board, control cabling etc., required for ITC of Air curtain at site. The air curtain shall be suitable for clean room application. |
| 16 | Air shower:Fabrication, supply and installation of air-shower suitable for decontaminating two persons at a time. The air shower shall be fabricated out of SS-304 sheet and as per technical specifications.i. Occupancy : 2 persons at a timeii. Material of construction : SS-304, Doors: Double skin insulated doors with viewing glass paneliii. Filters: Complete with HEPA and Pre filtersiv. Display :Display panel with counting timers |
| 17 | Supply, installation, testing and commissioning of microprocessor controlled air cooled packagedwater chilling machine of min 150 TR cooling capacity at 35 deg C ambient as per AHRI complete with air-cooled condenser, screw compressor, evaporator, expansion device, motor along with VFD drive and associated accessories as per tender specification. |
| 18 | Supply, installation, testing and commissioning of In-line vertical,Single Stage,Single Suction type centrifugal pump-motor set suitable for chilled water application complete with VFD compatible four (04) pole electrical motor as per technical specifications.Capacity : 1550 LPMDischarge head : 33 meter |
| 19 | Supply, installation, testing and commissioning of MS piping of following sizes & thickness / class for chilled water system complete with all required flanges, fittings, gaskets, fasteners, Nitrile rubberinsulation covered with aluminium cladding etc. as per tendertechnical specifications. |
| 20 | NB 200 mm class C |
| 21 | NB 150 mm class C |
| 22 | NB 80 mm class C |
| 23 | NB 40 mm class C |
| 24 | Supply, installation, testing and commissioning of flanged end, PN-16, CI/DI Butterfly valves of following sizes for chilled water system complete with all required counter flanges, fittings, gaskets, fasteners, Nitrile rubber insulation covered with aluminium cladding etc. as per tendertechnical specifications. |
| 25 | DN 150 mm |
| 26 | DN 80 mm |
| 27 | DN 40 mm |
| 28 | Supply, installation, testing and commissioning of PN-16, CI/DI balancing valves of following sizes for chilled water system complete with all required counter flanges, fittings, gaskets, fasteners, Nitrile rubber insulation covered with aluminium cladding etc. as per tendertechnical specifications. |
| 29 | DN 150 mm |
| 30 | DN 80 mm |
| 31 | Supply, installation, testing and commissioning of PN-16, CI/DI Non return valves of following sizes for chilled water system complete with all required counter flanges, fittings, gaskets, fasteners, Nitrile rubberinsulation covered with aluminium cladding etc. as per tendertechnical specifications. |
| 32 | DN 150 mm |
| 33 | DN 40 mm |
| 34 | Supply, installation, testing and commissioning of flanged end, PN-16, Y-strainer consists of strainer mesh & inlet/outlet connection of pumps of following sizes for chilled water system complete with all required counter flanges, fittings, gaskets, fasteners, Nitrile rubberinsulation covered with aluminium cladding etc. as per of technical specification. |
| 35 | DN 150 mm |
| 36 | DN 80 mm |
| 37 | Supply, installation, testing and commissioning of flanged end, PN-16, 3 way modulating valves with actuator having BMS compatibility of DN 80 mm size for chilled water system complete with all required counter flanges, fittings, gaskets, fasteners, Nitrile rubber insulation covered with aluminium cladding etc. as per tendertechnical specifications. |
| 38 | Supply, installation, testing and commissioning of PN 16/class-150, SS valves with flanges of following sizes for chilled water system complete with all required nipples, fittings, Nitrile rubberinsulation covered with aluminium cladding etc. as per tendertechnical specifications. |
| 39 | 25 mm NB |
| 40 | 40 mm NB |
| 41 | Supply, installation, testing and commissioningautomatic air vents valves, body & cover of valve shall be brass/SS as per tendertechnical specifications. |
| 42 | Providing, installation & commissioning of elevation moulded HDPE cylindrical vertical water storage tanks of approved make of 1500 litre capacity at required height with suitable cover at top including the cost of labour for making hole in the storage tank for inlet, outlet, scour and overflow, providing and fixing necessary GI nipples ranging from 15 mm to 50 mm NB of average 150 mm length with double check nuts, washers etc. complete as per tendertechnical specifications. |
| 43 | Supply, installation, testing and commissioning offollowing switch & gauges for measurement and control of parameters. |
| 44 | BMS compatible Flow switches forchilled water lines system. |
| 45 | Supply, installation, testing and commissioning of stem type thermometer having 0 to 50 deg C range ,100 mm dia dial with suitable stainless steel thermo wells for measurement of water temperature. |
| 46 | Supply, installation, testing and commissioning ofbourdon tube type Glycerin filled pressure gauge having 0 to 5 kg/sq. cm. Range,100 mm dia dial, U syphon and cockin stainless steel construction for measurement of water pressure. |
| 47 | Magnehelic gauge: Supply, installation & testing of100 mm dia, IP 67, Magnehelic gauge with die cast aluminum case, SS bezel and SS enclouser , tubes and SS fittings. |
| 48 | Supply, fabrication, installation and painting of MS structure required for support, flanges, structure etc. wherever ever required at site as per tendertechnical specifications. |
| 49 | Design, supply, installation and testing of centrifugal type, tangential in/out MS tank for chilled water system. The air separator shall have auto air purge valve along with clean-up / drain point at bottom with isolation valves. The required pressure shall be maintained into the chilled water systemas per tendertechnical specifications. |
| 50 | Testing, velidation & documentation of clean room as per ISO 14644 and technical specifications. |
| 51 | Supply, installation, testing and commissioning of following BMS compatible instruments for measurement and control of various parameters along with associated cabling. All analog I/Os of all instruments shall be 4-20 mAas per tendertechnical specifications. |
| 52 | Differential Pressure sensor and transmitter: Supply, installation, testing and commissioning of BMS compatible differential pressure (DP) sensor and transmitter for monitoring of AHU on/off status and filter dirty status in AHUas per tendertechnical specifications. |
| 53 | Relative humidity sensor and transmitter: Supply, installation, testing and commissioning of high accuracy (±1% or better for the span of 30% to 70%) Relative Humidity (RH) sensor and transmitter unit with associated cabling as per tender technical specifications |
| 54 | Temperature sensor and transmitter: Supply, installation, testing and commissioning of high accuracy (±0.03 deg.C @ 0 deg.C or better for the span of 0-35 deg. C) BMS compatible temperature sensor (1000 ohm platinum RTD type) and transmitter unit with associated cabling as per tender technical specifictions |
| 55 | Differential pressure cum air flow transmitter shall have BMS compatibility, 0…10V/4…20mA output signal, measuring range 0…50 m³/s, IP54 protection class, Accuracy: ±2% and T3015 aluminum flow sensing probewithmounting accessories. Necessary control and logic shall be provided with the air flow sensor. Scope shall also supply and installation of all required accessories along with associated control cabling for integration of the sensor in satisfactory manner. Manufacturer Test Certificate (TC) shall be submitted along with itemas per tendertechnical specifications. |
| 56 | Due point sensors with transmitter |
| 57 | Supply and laying GI earthing wire with accessories in cable tray / wall. |
| 58 | Supply and Installation of heavy gauge 25 mm dia PVC conduit . |
| 59 | HMI station: Supply, installation, testing and commissioning of server grade computer (HMI station) with BMS for AHUs, Configuration and monitoring software for Chiller system (Plant manager) and other associated licensed software alongwith development of SCADA system as per technical specification |
| 60 | Controller: Supply, installation, testing and commissioning of standalone BACnet/IP based modular type, BMS compatible DDC controller / automation station panel having integral web browser, I/O module, flash memory for programmed logic storage communication ports (RS 485, Ethernet RJ 45, and USB/additional ethernet), etc. For Air Handling Unit (AHU) control, monitoring, status indication, data logging, trends, report generation. The DDC controlled panel shall have redundant auxiliary power supplies with auto changeover, adjustible space heater having thermostat control, internal illumination, redundant ventilation fans, earthing provision etc as per tender technical specification. |
| 61 | UPS: Single phase 6 kVA online UPS with battery bank with 120 minutes backup as per the technical specifications. |
| 62 | Design, Fabrication, Supply, Installation, Testing & Commissioning of 3-phase CRCA sheet fabricated, duly powder coated power control Centre (PCC)/motor control centre (MCC) panel. PCC/MCC shall have following configurations: |
| 63 | MCC Panel 1 (for AHUs):Incomer: 800A FP MCCB (Ics≥50 kA) with Microprocessor trip release for O/L & S/C & E/F protection (LSIG) having individually adjustable current & time settings. Main busbar-800A TPN tinned copper busbar having maximum current density of 1.6A/sq.mm to withstand symmetrical fault level of 50 kA at 415 VOutgoing:1) 30 kW VFD feeders: 63A,TP MCCB (Ics≥50 kA, microprocessor trip release for O/L&S/C&E/F protection (LSIG) having individually adjustable current & time settings) with 30 kW VVVF drive along with 63A,AC-3 class,TP contactor, semiconductor fuses & all required switch gears/equipments &accessories for local &remote operation- 03 Nos.2) 18.5 KW VFD feeders: 63A,TP MCCB (Ics≥50 kA, microprocessor trip release for O/L&S/C&E/F protection (LSIG) having individually adjustable current & time settings) with 18.5 kW VVVF drive along with 63A,AC-3 class,TP contactor, semiconductor fuses & all required switch gears/equipments &accessories for local & remote operation- 063) MCCB feeders for heaters/preheaters//humidifiers: TP MCCB (Ics≥50 kA, microprocessor trip release for O/L&S/C&E/F protection (LSIG) having individually adjustable current & time settings) with power contactor suitable as per the current rating of reheater/preheater/humidifier, alongwith interlocking with signal/communication wire as per recommendation of OEM/EIC and complete with all accessories and internal wiring required for automatic and manual operation etc. complete as required and as per tendertechnical specifications. (A) 100A TP MCCB 50 kW Reheater/Preheater feeders - 07 Nos.4) Three phase power DB (integrated inside MCC panel 1):a) Incomer: 63 A, TP MCCB (Ics≥50 kA, microprocessor trip release for O/L&S/C&E/F protection (LSIG) having individually adjustable current & time settings) - 01 No.(b) Outgoings: 10A DP C-curve (Ics≥15 kA) MCB single phase feeders - 04 Nos16A DP C-curve (Ics≥15 kA) MCB single phase feeders - 04 Nos |
| 64 | MCC Panel-2 (for chiller)Incomer: 800A FP MCCB (Ics≥50 kA) with Microprocessor trip release for O/L & S/C & E/F protection (LSIG) having individually adjustable current & time settingsOutgoing:1) 200 kW chiller feeders: 400A, FP MCCB (Ics≥50kA) with microprocessor trip release for O/L, S/C & E/Fprotection (LSIG) having individually adjustable current &time settings with all required switch gears/ equipments & accessories for local and remote operation.- 02 Nos.2) 22 KW VFD feeders: 63A,TP MCCB (Ics≥50 kA, microprocessor trip release for O/L&S/C&E/F protection (LSIG) having individually adjustable current & time settings) with 22 KW VVVF drive along with 63A,AC-3 class,TP contactor, semiconductor fuses & all required switch gears/equipments &accessories for local & remote operation- 03 Nos.3) Three phase power DB (integrated inside MCC panel-2):a) Incomer: 63A, TP MCCB (Ics≥50 kA, microprocessor trip release for O/L&S/C&E/F protection (LSIG) having individually adjustable current & time settings) - 01 No.(b) Outgoings: 10A DP C-curve (Ics≥15 kA) MCB single phase feeders - 04 Nos16A DP C-curve (Ics≥15 kA) MCB single phase feeders - 04 Nos |
| 65 | Supply and installation of 150X100 mm HDG/Electrozinc perforated type cable trays on wall/metallic structure with all accessories as per item no 24 of technical specifications i.e. couplers,nuts&bolts etc as per tendertechnical specifications. |
| 66 | Supply and installation of 300 mm wide ladder type GI cable trays made out of 2mm thick MS sheet with 100mm side channels, rungs 35mmX15mmX15mm with CC spacing of 250mm with coupler plates including hardware, MS supports,GI earth strip (50X6mm) etc. as per tendertechnical specifications. |
| 67 | Supply & laying of1.1 KV grade , XLPE with FRLS PVC outer sheath insulatedArmored Copper Conductor cableof the following sizesas per tendertechnical specifications. |
| 68 | 3 core X 16 sq mm Cu Armoured Cable |
| 69 | 3 core X 25 sq mm Cu Armoured Cable |
| 70 | 3.5 core X 120 sq mm Cu Armoured Cable |
| 71 | Only installation, testing and commissioning of 1100 V grade power armoured aluminium conductor power cable of 3.5core 240 sq. mm size in trech / wall by supply and fixing of clamps and all required hardwareas per tendertechnical specifications. |
| 72 | Supply and installation of end termination for following 1100V grade LT XLPE cable using Heavy duty Double compression, Brass gland, Cu lugs suitable for crimping, end boxcomplete as required andas per tendertechnical specifications. |
| 73 | 3 core X 16 sq mm Cu Armoured Cable. |
| 74 | 3 core X 25 sq mm Cu Armoured Cable. |
| 75 | 3.5 core X 120 sq mm Cu Armoured Cable. |
| 76 | 3.5 core X 240 sq mm Al Armoured Cable. |
| 77 | Supply and installation of Control/BMS cables of following sizes as per relevantas per tendertechnical specifications. |
| 78 | 2 pair of 4CX 1.5 sqmm copper, armoured multi-stranded twisted pair shielded FRLS control cable. |
| 79 | 1 pair or 2CX1.5 sqmm copper, armoured multi-stranded twisted pair shielded FRLS control cable. |
| 80 | Ethernet cable (CAT6A) |
| 81 | Supply and laying GI earthing strip with accessories in cable tray / wall. |
| 82 | Supply and demostration of Pre-programmed DDC at site. |
| 83 | Supply, installation, testing and commissioning of Electromagnetic flow meter of 150 mm dia. pipe line for measurement of chilled water flow in pipe lines as per tendertechnical specifications. |
| 84 | Supply and laying GI earthing strip / wire with accessories in cable tray / wall. |
